| Age | Commit message (Collapse) | Author |
|---|
|
Some TMIO variants need specific actions in their reset routine, but
they are all based on a generic reset routine. So, the optional 'reset'
callback will now only take care of the additional stuff and we will
have a generic function around it. Less code, easier to maintain, and
much more readable. Code in tmio_mmc.c is untested but in my TC6387XB
datasheet the SDIO part is reset independently from the SD part, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After Yamada-san's refactorization introducing 'tmio_mmc_host_alloc', we
can populate mmc_ops directly and don't need a layer inbetween.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This reverts commit a87852c6b8827b7fece78ae57d871d56e4348e30. It did fix
the issue, but was building on top of already wrong assumptions. The
driver missed that 'hw_reset' was only for resetting remote HW (card)
and not for the IP core. Since we fixed that in a previous patch, we can
now remove this patch to make it clear that 'reset' is for resetting the
IP core only. Also, cancelling DMA will only be called when actually
needed again. It will also allow for further cleanups and better
readability. Note that in addition to the revert, the call in
'tmio_mmc_execute_tuning' will be converted, too, to maintain the
current behaviour.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This driver got the usage of 'hw_reset' wrong and missed that it is used
to reset the remote HW (card) only, not the local one (controller). Move
everything to the proper 'reset' callback. Also, add the generic reset
code from TMIO, so we will ensure the same behaviour (it will get
refactored away in a later patch). This also means we need to drop
MMC_CAP_HW_RESET because this is currently not supported by our
hardware.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There is a one time delay because of a card detect debounce timer in the
controller IP. This timer runs as soon as power is applied to the module
regardless of whether a card is present or not and any writes to
SDHCI_POWER_ON will return 0 before it expires. This timeout has been
measured to be about 1 second in am654x and j721e.
Write-and-read-back in a loop on SDHCI_POWER_ON for a maximum of
1.5 seconds to make sure that the controller actually powers on.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200825170015.32285-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There seems to be no particular reason to only test for ARM, so allow
for build-testing on other platforms to increase coverage.
Build-tested on x86 with allyesconfig.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200824171854.406157-1-alex.dewar90@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Value assigned to a variable(err) is never used, so remove it.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1598265914-23606-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use kobj_to_dev() instead of container_of()
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1598230956-58523-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This adds the eMMC driver for the Sparx5 SoC. It is based upon the
designware IP, but requires some extra initialization and quirks.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200825081357.32354-3-lars.povlsen@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
via_save_pcictrlreg() should be called with host->lock held
as it writes to pm_pcictrl_reg, otherwise there can be a race
condition between via_sd_suspend() and via_sdc_card_detect().
The same pattern is used in the function via_reset_pcictrl()
as well, where via_save_pcictrlreg() is called with host->lock
held.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200822061528.7035-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some Intel BYT based host controllers support the setting of latency
tolerance. Accordingly, implement the PM QoS ->set_latency_tolerance()
callback. The raw register values are also exposed via debugfs.
Intel EHL controllers require this support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: cb3a7d4a0aec4e ("mmc: sdhci-pci: Add support for Intel EHL")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200818104508.7149-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When reading the test description, I thought a correction of the
xfer_size was tested, which is not the case. It is tested that the
xfer_size is correct. Use 'proper xfer_size' to remove this ambiguity.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200817115838.2981-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Previously the cycle timeout was converted to a microsecond value but
then incorrectly treated as a nanosecond timeout. This patch changes
the code to convert both the nanosecond timeout and the cycle timeout
to a microsecond value and use that directly.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20200814185011.3252020-1-t.schramm@manjaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For SDIO functions, SDIO cards and SD COMBO cards are exported revision
number and info strings from CISTPL_VERS_1 structure. Revision number
should indicate compliance of standard and info strings should contain
product information in same format as product information for PCMCIA cards.
Product information for PCMCIA cards should contain following strings in
this order: Manufacturer, Product Name, Lot number, Programming Conditions.
Note that not all SDIO cards export all those info strings in that order as
described in PCMCIA Metaformat Specification.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-5-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This simplify code for generating sdio config attributes and allows easily
define new sdio attributes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-4-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
They should indicate compliance of standard.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-3-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Before parsing CISTPL_VERS_1 structure check that its size is at least two
bytes to prevent buffer overflow.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to IC suggestion, everytime before sending the tuning command,
need to reset the usdhc, so to reset the tuning circuit, to let every
tuning command work well for the manual tuning method. For standard tuning
method, IC already add the reset operation in the hardware logic.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1597135057-22272-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Synopsys DesignWare MMC controller could be used in RISC-V and
C-SKY architectures.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/1596887102-9743-1-git-send-email-guoren@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Remove empty comment to fix W=1 compile warning:
drivers/mmc/host/s3cmci.c:400: warning: Cannot understand *
on line 400 - I thought it was a doc line
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200804151345.28005-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200718090614.88946-1-grandmaster@al2klimov.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SDHCI changed from using a tasklet to finish requests, to using an IRQ
thread i.e. commit c07a48c2651965 ("mmc: sdhci: Remove finish_tasklet").
Because this increased the latency to complete requests, a preparatory
change was made to complete the request from the IRQ handler if
possible i.e. commit 19d2f695f4e827 ("mmc: sdhci: Call mmc_request_done()
from IRQ handler if possible"). That alleviated the situation for MMC
block devices because the MMC block driver makes use of mmc_pre_req()
and mmc_post_req() so that successful requests are completed in the IRQ
handler and any DMA unmapping is handled separately in mmc_post_req().
However SDIO was still affected, and an example has been reported with
up to 20% degradation in performance.
Looking at SDIO I/O helper functions, sdio_io_rw_ext_helper() appeared
to be a possible candidate for making use of asynchronous requests
within its I/O loops, but analysis revealed that these loops almost
never iterate more than once, so the complexity of the change would not
be warrented.
Instead, mmc_pre_req() and mmc_post_req() are added before and after I/O
submission (mmc_wait_for_req) in mmc_io_rw_extended(). This still has
the potential benefit of reducing the duration of interrupt handlers, as
well as addressing the latency issue for SDHCI. It also seems a more
reasonable solution than forcing drivers to do everything in the IRQ
handler.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: c07a48c2651965 ("mmc: sdhci: Remove finish_tasklet")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200903082007.18715-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit b214fe592ab7 ("mmc: sdhci-of-esdhc: add erratum eSDHC7 support")
added code to check for a specific compatible string in the device-tree
on every esdhc interrupat. Instead of doing this record the quirk in
struct sdhci_esdhc and lookup the struct in esdhc_irq.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200903012029.25673-1-chris.packham@alliedtelesis.co.nz
Fixes: b214fe592ab7 ("mmc: sdhci-of-esdhc: add erratum eSDHC7 support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The commit cd57d07b1e4e ("sh: don't allow non-coherent DMA for NOMMU") made
CONFIG_NO_DMA to be set for some platforms, for good reasons.
Consequentially, CONFIG_HAS_DMA doesn't get set, which makes the DMA
mapping interface to be built as stub functions, but also prevent the
mmc_spi driver from being built as it depends on CONFIG_HAS_DMA.
It turns out that for some odd cases, the driver still relied on the DMA
mapping interface, even if the DMA was not actively being used.
To fixup the behaviour, let's drop the build dependency for CONFIG_HAS_DMA.
Moreover, as to allow the driver to succeed probing, let's move the DMA
initializations behind "#ifdef CONFIG_HAS_DMA".
Fixes: cd57d07b1e4e ("sh: don't allow non-coherent DMA for NOMMU")
Reported-by: Rich Felker <dalias@libc.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20200901150438.228887-1-ulf.hansson@linaro.org
|
|
As the comments in this patch say, if we tune and find all phases are
valid it's _almost_ as bad as no phases being found valid. Probably
all phases are not really reliable but we didn't detect where the
unreliable place is. That means we'll essentially be guessing and
hoping we get a good phase.
This is not just a problem in theory. It was causing real problems on
a real board. On that board, most often phase 10 is found as the only
invalid phase, though sometimes 10 and 11 are invalid and sometimes
just 11. Some percentage of the time, however, all phases are found
to be valid. When this happens, the current logic will decide to use
phase 11. Since phase 11 is sometimes found to be invalid, this is a
bad choice. Sure enough, when phase 11 is picked we often get mmc
errors later in boot.
I have seen cases where all phases were found to be valid 3 times in a
row, so increase the retry count to 10 just to be extra sure.
Fixes: 415b5a75da43 ("mmc: sdhci-msm: Add platform_execute_tuning implementation")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200827075809.1.If179abf5ecb67c963494db79c3bc4247d987419b@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The commit 61d7437ed1390 ("mmc: sdhci-acpi: Fix HS400 tuning for AMDI0040")
broke resume for eMMC HS400. When the system suspends the eMMC controller
is powered down. So, on resume we need to reinitialize the controller.
Although, amd_sdhci_host was not getting cleared, so the DLL was never
re-enabled on resume. This results in HS400 being non-functional.
To fix the problem, this change clears the tuned_clock flag, clears the
dll_enabled flag and disables the DLL on reset.
Fixes: 61d7437ed1390 ("mmc: sdhci-acpi: Fix HS400 tuning for AMDI0040")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200831150517.1.I93c78bfc6575771bb653c9d3fca5eb018a08417d@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Fix HS400 tuning for ACPI ID AMDI0040
- Fix reset of CQHCI for Intel GLK-based controllers
- Use correct timeout clock for Tegra186/194/210
- Fix eMMC mounting on mt7622/Bpi-64
* tag 'mmc-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
sdhci: tegra: Add missing TMCLK for data timeout
arm64: tegra: Add missing timeout clock to Tegra194 SDMMC nodes
arm64: tegra: Add missing timeout clock to Tegra186 SDMMC nodes
arm64: tegra: Add missing timeout clock to Tegra210 SDMMC
dt-bindings: mmc: tegra: Add tmclk for Tegra210 and later
sdhci: tegra: Remove SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK for Tegra186
sdhci: tegra: Remove SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK for Tegra210
arm64: dts: mt7622: add reset node for mmc device
dt-bindings: mmc: Add missing description for clk_in/out_sd1
mmc: mediatek: add optional module reset property
mmc: dt-bindings: Add resets/reset-names for Mediatek MMC bindings
mmc: sdhci-pci: Fix SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers
mmc: sdhci-acpi: Fix HS400 tuning for AMDI0040
|
|
commit b5a84ecf025a ("mmc: tegra: Add Tegra210 support")
Tegra210 and later has a separate sdmmc_legacy_tm (TMCLK) used by Tegra
SDMMC hawdware for data timeout to achive better timeout than using
SDCLK and using TMCLK is recommended.
USE_TMCLK_FOR_DATA_TIMEOUT bit in Tegra SDMMC register
SDHCI_TEGRA_VENDOR_SYS_SW_CTRL can be used to choose either TMCLK or
SDCLK for data timeout.
Default USE_TMCLK_FOR_DATA_TIMEOUT bit is set to 1 and TMCLK is used
for data timeout by Tegra SDMMC hardware and having TMCLK not enabled
is not recommended.
So, this patch adds quirk NVQUIRK_HAS_TMCLK for SoC having separate
timeout clock and keeps TMCLK enabled all the time.
Fixes: b5a84ecf025a ("mmc: tegra: Add Tegra210 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-8-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
commit 4346b7c7941d ("mmc: tegra: Add Tegra186 support")
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set for Tegra186 from the
beginning of its support in driver.
Tegra186 SDMMC hardware by default uses timeout clock (TMCLK) instead
of SDCLK and this quirk should not be set.
So, this patch remove this quirk for Tegra186.
Fixes: 4346b7c7941d ("mmc: tegra: Add Tegra186 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-3-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
commit b5a84ecf025a ("mmc: tegra: Add Tegra210 support")
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set for Tegra210 from the
beginning of Tegra210 support in the driver.
Tegra210 SDMMC hardware by default uses timeout clock (TMCLK)
instead of SDCLK and this quirk should not be set.
So, this patch remove this quirk for Tegra210.
Fixes: b5a84ecf025a ("mmc: tegra: Add Tegra210 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch fixs eMMC-Access on mt7622/Bpi-64.
Before we got these Errors on mounting eMMC ion R64:
[ 48.664925] blk_update_request: I/O error, dev mmcblk0, sector 204800 op 0x1:(WRITE)
flags 0x800 phys_seg 1 prio class 0
[ 48.676019] Buffer I/O error on dev mmcblk0p1, logical block 0, lost sync page write
This patch adds a optional reset management for msdc.
Sometimes the bootloader does not bring msdc register
to default state, so need reset the msdc controller.
Cc: <stable@vger.kernel.org> # v5.4+
Fixes: 966580ad236e ("mmc: mediatek: add support for MT7622 SoC")
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20200814014346.6496-4-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
For Intel controllers, SDHCI_RESET_ALL resets also CQHCI registers.
Normally, SDHCI_RESET_ALL is not used while CQHCI is enabled, but that can
happen on the error path. e.g. if mmc_cqe_recovery() fails, mmc_blk_reset()
is called which, for a eMMC that does not support HW Reset, will cycle the
bus power and the driver will perform SDHCI_RESET_ALL.
So whenever performing SDHCI_RESET_ALL ensure CQHCI is deactivated.
That will force the driver to reinitialize CQHCI when it is next used.
A similar change was done already for sdhci-msm, and other drivers using
CQHCI might benefit from a similar change, if they also have CQHCI reset
by SDHCI_RESET_ALL.
Fixes: 8ee82bda230fc9 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Cc: stable@vger.kernel.org # 5.4.x: 0ffa6cfbd949: mmc: cqhci: Add cqhci_deactivate()
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200819121848.16967-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The AMD eMMC Controller can only use the tuned clock while in HS200 and
HS400 mode. If we switch to a different mode, we need to disable the
tuned clock. If we have previously performed tuning and switch back to
HS200 or HS400, we can re-enable the tuned clock.
Previously the tuned clock was not getting disabled when switching to
DDR52 which is part of the HS400 tuning sequence.
Fixes: 34597a3f60b1 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200819125832.v2.1.Ie8f0689ec9f449203328b37409d1cf06b565f331@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Rather than call the internal s3c_gpio_cfgall_range() function
through a platform header, move the code into the set_power
callback that is already exported by the board, and add
a default implementation.
In DT mode, the code already does not set the pin config,
so nothing changes there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200806182059.2431-29-krzk@kernel.org
[krzk: Rebase and correct set_power in mach-h1940.c]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The plat-samsung directory and mach-s5pv210 can be build
completely independently, so split the two Kconfig symbols
CONFIG_PLAT_SAMSUNG and CONFIG_ARCH_S5PV210.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-18-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Now that no code in arch/arm is shared between mach-exynos and the
others, make the split formal.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200806182059.2431-15-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The s3cmci driver does not use machine header mach/dma.h.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add a new host cap bit and a corresponding DT property, to support
power cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host controllers:
- Convert a few DT bindings to the json-schema
- mtk-sd:
- Add support for command queue through cqhci
- Add support for the MT6779 variant
- renesas_sdhi_internal_dmac:
- Fix dma unmapping in the error path
- sdhci_am654:
- Add support for the AM65x PG2.0 variant
- Extend support for phys/clocks
- sdhci-cadence:
- Drop incorrect HW tuning for SD mode
- sdhci-msm:
- Add support for interconnect bandwidth scaling
- Enable internal voltage control
- Enable low power state for pinctrls
- sdhci-of-at91:
- Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli:
- Improve clock handling for GL975x
- sdhci-pci-o2micro:
- Add HW tuning for SDR104 mode
- Fix support for O2 host controller Seabird1"
* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
mmc: mediatek: make function msdc_cqe_disable() static
MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
dt-bindings: mmc: mediatek: Add document for mt6779
mmc: mediatek: command queue support
mmc: mediatek: refine msdc timeout api
mmc: mediatek: add MT6779 MMC driver support
mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
mmc: via-sdmmc: use generic power management
memstick: jmb38x_ms: use generic power management
mmc: sdhci-cadence: do not use hardware tuning for SD mode
mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
mmc: cqhci: Fix a print format for the task descriptor
mmc: sdhci-of-arasan: fix timings allocation code
mmc: sdhci: Fix a potential uninitialized variable
dt-bindings: mmc: renesas,sdhi: convert to YAML
dt-bindings: mmc: convert arasan sdhci bindings to yaml
mmc: sdhci: Fix potential null pointer access while accessing vqmmc
mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (322 commits)
habanalabs: remove unused but set variable 'ctx_asid'
nvmem: qcom-spmi-sdam: Enable multiple devices
dt-bindings: nvmem: SID: add binding for A100's SID controller
nvmem: update Kconfig description
nvmem: qfprom: Add fuse blowing support
dt-bindings: nvmem: Add properties needed for blowing fuses
dt-bindings: nvmem: qfprom: Convert to yaml
nvmem: qfprom: use NVMEM_DEVID_AUTO for multiple instances
nvmem: core: add support to auto devid
nvmem: core: Add nvmem_cell_read_u8()
nvmem: core: Grammar fixes for help text
nvmem: sc27xx: add sc2730 efuse support
nvmem: Enforce nvmem stride in the sysfs interface
MAINTAINERS: Add git tree for NVMEM FRAMEWORK
nvmem: sprd: Fix return value of sprd_efuse_probe()
drivers: android: Fix the SPDX comment style
drivers: android: Fix a variable declaration coding style issue
drivers: android: Remove braces for a single statement if-else block
drivers: android: Remove the use of else after return
drivers: android: Fix a variable declaration coding style issue
...
|
|
The sparse tool complains as follows:
drivers/mmc/host/mtk-sd.c:2269:6: warning:
symbol 'msdc_cqe_disable' was not declared. Should it be static?
This function is not used outside of mtk-sd.c, so this commit
marks it static.
Fixes: 88bd652b3c74 ("mmc: mediatek: command queue support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Link: https://lore.kernel.org/r/20200727171129.2945-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull uninitialized_var() macro removal from Kees Cook:
"This is long overdue, and has hidden too many bugs over the years. The
series has several "by hand" fixes, and then a trivial treewide
replacement.
- Clean up non-trivial uses of uninitialized_var()
- Update documentation and checkpatch for uninitialized_var() removal
- Treewide removal of uninitialized_var()"
* tag 'uninit-macro-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
compiler: Remove uninitialized_var() macro
treewide: Remove uninitialized_var() usage
checkpatch: Remove awareness of uninitialized_var() macro
mm/debug_vm_pgtable: Remove uninitialized_var() usage
f2fs: Eliminate usage of uninitialized_var() macro
media: sur40: Remove uninitialized_var() usage
KVM: PPC: Book3S PR: Remove uninitialized_var() usage
clk: spear: Remove uninitialized_var() usage
clk: st: Remove uninitialized_var() usage
spi: davinci: Remove uninitialized_var() usage
ide: Remove uninitialized_var() usage
rtlwifi: rtl8192cu: Remove uninitialized_var() usage
b43: Remove uninitialized_var() usage
drbd: Remove uninitialized_var() usage
x86/mm/numa: Remove uninitialized_var() usage
docs: deprecated.rst: Add uninitialized_var()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The most significant change here is the extension of the Energy Model
to cover non-CPU devices (as well as CPUs) from Lukasz Luba.
There is also some new hardware support (Ice Lake server idle states
table for intel_idle, Sapphire Rapids and Power Limit 4 support in the
RAPL driver), some new functionality in the existing drivers (eg. a
new switch to disable/enable CPU energy-efficiency optimizations in
intel_pstate, delayed timers in devfreq), some assorted fixes (cpufreq
core, intel_pstate, intel_idle) and cleanups (eg. cpuidle-psci,
devfreq), including the elimination of W=1 build warnings from cpufreq
done by Lee Jones.
Specifics:
- Make the Energy Model cover non-CPU devices (Lukasz Luba).
- Add Ice Lake server idle states table to the intel_idle driver and
eliminate a redundant static variable from it (Chen Yu, Rafael
Wysocki).
- Eliminate all W=1 build warnings from cpufreq (Lee Jones).
- Add support for Sapphire Rapids and for Power Limit 4 to the Intel
RAPL power capping driver (Sumeet Pawnikar, Zhang Rui).
- Fix function name in kerneldoc comments in the idle_inject power
capping driver (Yangtao Li).
- Fix locking issues with cpufreq governors and drop a redundant
"weak" function definition from cpufreq (Viresh Kumar).
- Rearrange cpufreq to register non-modular governors at the
core_initcall level and allow the default cpufreq governor to be
specified in the kernel command line (Quentin Perret).
- Extend, fix and clean up the intel_pstate driver (Srinivas
Pandruvada, Rafael Wysocki):
* Add a new sysfs attribute for disabling/enabling CPU
energy-efficiency optimizations in the processor.
* Make the driver avoid enabling HWP if EPP is not supported.
* Allow the driver to handle numeric EPP values in the sysfs
interface and fix the setting of EPP via sysfs in the active
mode.
* Eliminate a static checker warning and clean up a kerneldoc
comment.
- Clean up some variable declarations in the powernv cpufreq driver
(Wei Yongjun).
- Fix up the ->enter_s2idle callback definition to cover the case
when it points to the same function as ->idle correctly (Neal Liu).
- Rearrange and clean up the PSCI cpuidle driver (Ulf Hansson).
- Make the PM core emit "changed" uevent when adding/removing the
"wakeup" sysfs attribute of devices (Abhishek Pandit-Subedi).
- Add a helper macro for declaring PM callbacks and use it in the MMC
jz4740 driver (Paul Cercueil).
- Fix white space in some places in the hibernate code and make the
system-wide PM code use "const char *" where appropriate (Xiang
Chen, Alexey Dobriyan).
- Add one more "unsafe" helper macro to the freezer to cover the NFS
use case (He Zhe).
- Change the language in the generic PM domains framework to use
parent/child terminology and clean up a typo and some comment
fromatting in that code (Kees Cook, Geert Uytterhoeven).
- Update the operating performance points OPP framework (Lukasz Luba,
Andrew-sh.Cheng, Valdis Kletnieks):
* Refactor dev_pm_opp_of_register_em() and update related drivers.
* Add a missing function export.
* Allow disabled OPPs in dev_pm_opp_get_freq().
- Update devfreq core and drivers (Chanwoo Choi, Lukasz Luba, Enric
Balletbo i Serra, Dmitry Osipenko, Kieran Bingham, Marc Zyngier):
* Add support for delayed timers to the devfreq core and make the
Samsung exynos5422-dmc driver use it.
* Unify sysfs interface to use "df-" as a prefix in instance
names consistently.
* Fix devfreq_summary debugfs node indentation.
* Add the rockchip,pmu phandle to the rk3399_dmc driver DT
bindings.
* List Dmitry Osipenko as the Tegra devfreq driver maintainer.
* Fix typos in the core devfreq code.
- Update the pm-graph utility to version 5.7 including a number of
fixes related to suspend-to-idle (Todd Brandt).
- Fix coccicheck errors and warnings in the cpupower utility (Shuah
Khan).
- Replace HTTP links with HTTPs ones in multiple places (Alexander A.
Klimov)"
* tag 'pm-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (71 commits)
cpuidle: ACPI: fix 'return' with no value build warning
cpufreq: intel_pstate: Fix EPP setting via sysfs in active mode
cpufreq: intel_pstate: Rearrange the storing of new EPP values
intel_idle: Customize IceLake server support
PM / devfreq: Fix the wrong end with semicolon
PM / devfreq: Fix indentaion of devfreq_summary debugfs node
PM / devfreq: Clean up the devfreq instance name in sysfs attr
memory: samsung: exynos5422-dmc: Add module param to control IRQ mode
memory: samsung: exynos5422-dmc: Adjust polling interval and uptreshold
memory: samsung: exynos5422-dmc: Use delayed timer as default
PM / devfreq: Add support delayed timer for polling mode
dt-bindings: devfreq: rk3399_dmc: Add rockchip,pmu phandle
PM / devfreq: tegra: Add Dmitry as a maintainer
PM / devfreq: event: Fix trivial spelling
PM / devfreq: rk3399_dmc: Fix kernel oops when rockchip,pmu is absent
cpuidle: change enter_s2idle() prototype
cpuidle: psci: Prevent domain idlestates until consumers are ready
cpuidle: psci: Convert PM domain to platform driver
cpuidle: psci: Fix error path via converting to a platform driver
cpuidle: psci: Fail cpuidle registration if set OSI mode failed
...
|
|
Pull core block updates from Jens Axboe:
"Good amount of cleanups and tech debt removals in here, and as a
result, the diffstat shows a nice net reduction in code.
- Softirq completion cleanups (Christoph)
- Stop using ->queuedata (Christoph)
- Cleanup bd claiming (Christoph)
- Use check_events, moving away from the legacy media change
(Christoph)
- Use inode i_blkbits consistently (Christoph)
- Remove old unused writeback congestion bits (Christoph)
- Cleanup/unify submission path (Christoph)
- Use bio_uninit consistently, instead of bio_disassociate_blkg
(Christoph)
- sbitmap cleared bits handling (John)
- Request merging blktrace event addition (Jan)
- sysfs add/remove race fixes (Luis)
- blk-mq tag fixes/optimizations (Ming)
- Duplicate words in comments (Randy)
- Flush deferral cleanup (Yufen)
- IO context locking/retry fixes (John)
- struct_size() usage (Gustavo)
- blk-iocost fixes (Chengming)
- blk-cgroup IO stats fixes (Boris)
- Various little fixes"
* tag 'for-5.9/block-20200802' of git://git.kernel.dk/linux-block: (135 commits)
block: blk-timeout: delete duplicated word
block: blk-mq-sched: delete duplicated word
block: blk-mq: delete duplicated word
block: genhd: delete duplicated words
block: elevator: delete duplicated word and fix typos
block: bio: delete duplicated words
block: bfq-iosched: fix duplicated word
iocost_monitor: start from the oldest usage index
iocost: Fix check condition of iocg abs_vdebt
block: Remove callback typedefs for blk_mq_ops
block: Use non _rcu version of list functions for tag_set_list
blk-cgroup: show global disk stats in root cgroup io.stat
blk-cgroup: make iostat functions visible to stat printing
block: improve discard bio alignment in __blkdev_issue_discard()
block: change REQ_OP_ZONE_RESET and REQ_OP_ZONE_RESET_ALL to be odd numbers
block: defer flush request no matter whether we have elevator
block: make blk_timeout_init() static
block: remove retry loop in ioc_release_fn()
block: remove unnecessary ioc nested locking
block: integrate bd_start_claiming into __blkdev_get
...
|
|
Use the newly introduced pm_ptr() macro to simplify the code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This should resolve the merge/build issues reported when trying to
create linux-next.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Support command queue for mt6779 platform.
a. Add msdc_set_busy_timeout() to calculate emmc write timeout.
b. Connect mtk msdc driver to cqhci driver through
host->cq_host->ops = &msdc_cmdq_ops;
c. msdc_cmdq_irq() will link up with cqchi_irq(). Besides, it provides
more irq error messages like RSPCRCERR/CMDTO/DATACRCERR/DATTMO.
d. Select kernel config MMC_CQHCI for MMC_MTK
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/1595205759-5825-4-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Extract msdc timeout api common part to have
better code architecture and avoid redundant code.
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1595205759-5825-3-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add new code to support MT6779 mmc driver.
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Link: https://lore.kernel.org/r/1595205759-5825-2-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
