| Age | Commit message (Collapse) | Author |
|---|
|
commit e7794c14fd73e5eb4a3e0ecaa5334d5a17377c50 upstream.
When RPMB was converted to a character device, it added support for
multiple RPMB partitions (Commit 97548575bef3 ("mmc: block: Convert RPMB to
a character device").
One of the changes in this commit was transforming the variable target_part
defined in __mmc_blk_ioctl_cmd into a bitmask. This inadvertently regressed
the validation check done in mmc_blk_part_switch_pre() and
mmc_blk_part_switch_post(), so let's fix it.
Fixes: 97548575bef3 ("mmc: block: Convert RPMB to a character device")
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231201153143.1449753-1-jorge@foundries.io
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c124d998ea0c9022e247b11ac51f86ec8afa0e1 upstream.
Commit 4bc31edebde5 ("mmc: core: Set HS clock speed before sending
HS CMD13") set HS clock (52MHz) before switching to HS mode. For this
freq, FCLK_DIV5 will be selected and div value is 10 (reg value is 9).
Then we set rx_clk_phase to 11 or 15 which is out of range and make
hardware frozen. After we send command request, no irq will be
interrupted and the mmc driver will keep to wait for request finished,
even durning rebooting.
So let's set it to Phase 90 which should work in most cases. Then let
meson_mx_sdhc_execute_tuning() to find the accurate value for data
transfer.
If this doesn't work, maybe need to define a factor in dts.
Fixes: e4bf1b0970ef ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/TYZPR01MB5556A3E71554A2EC08597EA4C9CDA@TYZPR01MB5556.apcprd01.prod.exchangelabs.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c616696a902987352426fdaeec1b0b3240949e6b upstream.
STOP command does not guarantee to wait while busy, but subsequent command
MMC_CMDQ_TASK_MGMT to discard the queue will fail if the card is busy, so
be sure to wait by employing mmc_poll_for_busy().
Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Link: https://lore.kernel.org/r/20231103084720.6886-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 174925d340aac55296318e43fd96c0e1d196e105 upstream.
During CQE error recovery, error-free data commands get requeued if there
is any data left to transfer, but non-data commands are completed even
though they have not been processed. Requeue them instead.
Note the only non-data command is cache flush, which would have resulted in
a cache flush being lost if it was queued at the time of CQE recovery.
Fixes: 1e8e55b67030 ("mmc: block: Add CQE support")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8155d1fa3a747baad5caff5f8303321d68ddd48c upstream.
It is important that MMC_CMDQ_TASK_MGMT command to discard the queue is
successful because otherwise a subsequent reset might fail to flush the
cache first. Retry it and the previous STOP command.
Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-5-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1de1b77982e1a1df9707cb11f9b1789e6b8919d4 upstream.
If a task completion notification (TCN) is received when there is no
outstanding task, the cqhci driver issues a "spurious TCN" warning. This
was observed to happen right after CQE error recovery.
When an error interrupt is received the driver runs recovery logic.
It halts the controller, clears all pending tasks, and then re-enables
it. On some platforms, like Intel Jasper Lake, a stale task completion
event was observed, regardless of the CQHCI_CLEAR_ALL_TASKS bit being set.
This results in either:
a) Spurious TC completion event for an empty slot.
b) Corrupted data being passed up the stack, as a result of premature
completion for a newly added task.
Rather than add a quirk for affected controllers, ensure tasks are cleared
by toggling CQHCI_ENABLE, which would happen anyway if
cqhci_clear_all_tasks() timed out. This is simpler and should be safe and
effective for all controllers.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Reported-by: Kornel Dulęba <korneld@chromium.org>
Tested-by: Kornel Dulęba <korneld@chromium.org>
Co-developed-by: Kornel Dulęba <korneld@chromium.org>
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-7-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 35597bdb04ec27ef3b1cea007dc69f8ff5df75a5 upstream.
A correctly operating controller should successfully halt and clear tasks.
Failure may result in errors elsewhere, so promote messages from debug to
warnings.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b578d5d18e929aa7c007a98cce32657145dde219 upstream.
Failing to halt complicates the recovery. Additionally, unless the card or
controller are stuck, which is expected to be very rare, then the halt
should succeed, so it is better to wait. Set a large timeout.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103084720.6886-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 477865af60b2117ceaa1d558e03559108c15c78c upstream.
With cat regulator_summary, we found that vqmmc was not shutting
down after the card was pulled.
cat /sys/kernel/debug/regulator/regulator_summary
1.before fix
1)Insert SD card
vddsdio 1 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 1 0mA 3500mV 3600mV
2)Pull out the SD card
vddsdio 1 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 1 0mA 3500mV 3600mV
2.after fix
1)Insert SD cardt
vddsdio 1 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 1 0mA 3500mV 3600mV
2)Pull out the SD card
vddsdio 0 1 0 unknown 3500mV 0mA 1200mV 3750mV
71100000.mmc-vqmmc 0 0mA 3500mV 3600mV
Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231115083406.7368-1-wenchao.chen@unisoc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9ed644f58670865cf067351deb71010bd87a52f upstream.
To address IO performance commit f9e5b33934ce
("mmc: host: Improve I/O read/write performance for GL9763E")
limited LPM negotiation to runtime suspend state.
The problem is that it only flips the switch in the runtime PM
resume/suspend logic.
Disable LPM negotiation in gl9763e_add_host.
This helps in two ways:
1. It was found that the LPM switch stays in the same position after
warm reboot. Having it set in init helps with consistency.
2. Disabling LPM during the first runtime resume leaves us susceptible
to the performance issue in the time window between boot and the
first runtime suspend.
Fixes: f9e5b33934ce ("mmc: host: Improve I/O read/write performance for GL9763E")
Cc: stable@vger.kernel.org
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Reviewed-by: Sven van Ashbrook <svenva@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231114115516.1585361-1-korneld@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 015c9cbcf0ad709079117d27c2094a46e0eadcdb upstream.
Due to a flaw in the hardware design, the GL9750 replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9750
PCI config. Therefore, the replay timer timeout must be masked.
Fixes: d7133797e9e1 ("mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter ASPM L1.2")
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.geng@canonical.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231107095741.8832-2-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d7133797e9e1b72fd89237f68cb36d745599ed86 upstream.
When GL9750 enters ASPM L1 sub-states, it will stay at L1.1 and will not
enter L1.2. The workaround is to toggle PM state to allow GL9750 to enter
ASPM L1.2.
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20230912091710.7797-1-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed9009ad300c0f15a3ecfe9613547b1962bde02c upstream.
Micron MTFC4GACAJCN eMMC supports cache but requires that flush cache
operation be allowed only after a write has occurred. Otherwise, the
cache flush command or subsequent commands will time out.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231030224809.59245-1-beanhuo@iokpp.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71956d0cb56c1e5f9feeb4819db87a076418e930 upstream.
ti,otap-del-sel-legacy/ti,itap-del-sel-legacy passed from DT
are currently ignored for all SD/MMC and eMMC modes. Fix this
by making start loop index to MMC_TIMING_LEGACY.
Fixes: 8ee5fc0e0b3b ("mmc: sdhci_am654: Update OTAPDLY writes")
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231026061458.1116276-1-n-yadav@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b44f9da81783fda72632ef9b0d05ea3f3ca447a5 upstream.
This error path should return -EINVAL instead of success.
Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/0769d30c-ad80-421b-bf5d-7d6f5d85604e@moroto.mountain
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 57925e16c9f7d18012bcf45bfa658f92c087981a upstream.
For the t7 and older SoC families, the CMD_CFG_ERROR has no effect.
Starting from SoC family C3, setting this bit without SG LINK data
address will cause the controller to generate an IRQ and stop working.
To fix it, don't set the bit CMD_CFG_ERROR anymore.
Fixes: 18f92bc02f17 ("mmc: meson-gx: make sure the descriptor is stopped on errors")
Signed-off-by: Rong Chen <rong.chen@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231026073156.2868310-1-rong.chen@amlogic.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85dd3af64965c1c0eb7373b340a1b1f7773586b0 upstream.
Due to a flaw in the hardware design, the GL9755 replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9755
PCI config. Therefore, the replay timer timeout must be masked.
Fixes: 36ed2fd32b2c ("mmc: sdhci-pci-gli: A workaround to allow GL9755 to enter ASPM L1.2")
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.geng@canonical.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231107095741.8832-3-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 421b605edb1ce611dee06cf6fd9a1c1f2fd85ad0 upstream.
This reverts commit 84ee19bffc9306128cd0f1c650e89767079efeff.
The commit above made quirks with an OEMID fail to be applied, as they
were checking card->cid.oemid for the full 16 bits defined in MMC_FIXUP
macros but the field would only contain the bottom 8 bits.
eMMC v5.1A might have bogus values in OEMID's higher bits so another fix
will be made, but it has been decided to revert this until that is ready.
Fixes: 84ee19bffc93 ("mmc: core: Capture correct oemid-bits for eMMC cards")
Link: https://lkml.kernel.org/r/ZToJsSLHr8RnuTHz@codewreck.org
Link: https://lkml.kernel.org/r/CAPDyKFqkKibcXnwjnhc3+W1iJBHLeqQ9BpcZrSwhW2u9K2oUtg@mail.gmail.com
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Cc: stable@vger.kernel.org
Cc: Alex Fetters <Alex.Fetters@garmin.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20231103004220.1666641-1-asmadeus@codewreck.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The OEMID is an 8-bit binary number rather than 16-bit as the current code
parses for. The OEMID occupies bits [111:104] in the CID register, see the
eMMC spec JESD84-B51 paragraph 7.2.3. It seems that the 16-bit comes from
the legacy MMC specs (v3.31 and before).
Let's fix the parsing by simply move to use 8-bit instead of 16-bit. This
means we ignore the impact on some of those old MMC cards that may be out
there, but on the other hand this shouldn't be a problem as the OEMID seems
not be an important feature for these cards.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230927071500.1791882-1-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use atomic readl_poll_timeout_atomic, because msdc_reset_hw
may be invoked in IRQ handler in the following context:
msdc_irq() -> msdc_cmd_done() -> msdc_reset_hw()
The following kernel BUG stack trace can be observed on
Genio 1200 EVK after initializing MSDC1 hardware during kernel boot:
[ 1.187441] BUG: scheduling while atomic: swapper/0/0/0x00010002
[ 1.189157] Modules linked in:
[ 1.204633] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.15.42-mtk+modified #1
[ 1.205713] Hardware name: MediaTek Genio 1200 EVK-P1V2-EMMC (DT)
[ 1.206484] Call trace:
[ 1.206796] dump_backtrace+0x0/0x1ac
[ 1.207266] show_stack+0x24/0x30
[ 1.207692] dump_stack_lvl+0x68/0x84
[ 1.208162] dump_stack+0x1c/0x38
[ 1.208587] __schedule_bug+0x68/0x80
[ 1.209056] __schedule+0x6ec/0x7c0
[ 1.209502] schedule+0x7c/0x110
[ 1.209915] schedule_hrtimeout_range_clock+0xc4/0x1f0
[ 1.210569] schedule_hrtimeout_range+0x20/0x30
[ 1.211148] usleep_range_state+0x84/0xc0
[ 1.211661] msdc_reset_hw+0xc8/0x1b0
[ 1.212134] msdc_cmd_done.isra.0+0x4ac/0x5f0
[ 1.212693] msdc_irq+0x104/0x2d4
[ 1.213121] __handle_irq_event_percpu+0x68/0x280
[ 1.213725] handle_irq_event+0x70/0x15c
[ 1.214230] handle_fasteoi_irq+0xb0/0x1a4
[ 1.214755] handle_domain_irq+0x6c/0x9c
[ 1.215260] gic_handle_irq+0xc4/0x180
[ 1.215741] call_on_irq_stack+0x2c/0x54
[ 1.216245] do_interrupt_handler+0x5c/0x70
[ 1.216782] el1_interrupt+0x30/0x80
[ 1.217242] el1h_64_irq_handler+0x1c/0x2c
[ 1.217769] el1h_64_irq+0x78/0x7c
[ 1.218206] cpuidle_enter_state+0xc8/0x600
[ 1.218744] cpuidle_enter+0x44/0x5c
[ 1.219205] do_idle+0x224/0x2d0
[ 1.219624] cpu_startup_entry+0x30/0x80
[ 1.220129] rest_init+0x108/0x134
[ 1.220568] arch_call_rest_init+0x1c/0x28
[ 1.221094] start_kernel+0x6c0/0x700
[ 1.221564] __primary_switched+0xc0/0xc8
Fixes: ffaea6ebfe9c ("mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling")
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioachino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230922095348.22182-1-pablo.sun@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Userspace has currently no way of checking the internal R1 response error
bits for some commands. This is a problem for some commands, like RPMB for
example. Typically, we may detect that the busy completion has successfully
ended, while in fact the card did not complete the requested operation.
To fix the problem, let's always poll with CMD13 for these commands and
during the polling, let's also aggregate the R1 response bits. Before
completing the ioctl request, let's propagate the R1 response bits too.
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Co-developed-by: Christian Loehle <christian.loehle@arm.com>
Signed-off-by: Christian Loehle <christian.loehle@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230913112921.553019-1-ulf.hansson@linaro.org
|
|
Return an error code if sdhci_sprd_get_best_clk_sample() fails.
Currently, it returns success.
Fixes: d83d251bf3c2 ("mmc: sdhci-sprd: Add SD HS mode online tuning")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Wenchao Chen <wenchao.chen@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/a8af0a08-8405-43cc-bd83-85ff25f572ca@moroto.mountain
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
To improve the r/w performance of GL9763E, the current driver inhibits LPM
negotiation while the device is active.
This prevents a large number of SoCs from suspending, notably x86 systems
which commonly use S0ix as the suspend mechanism - for example, Intel
Alder Lake and Raptor Lake processors.
Failure description:
1. Userspace initiates s2idle suspend (e.g. via writing to
/sys/power/state)
2. This switches the runtime_pm device state to active, which disables
LPM negotiation, then calls the "regular" suspend callback
3. With LPM negotiation disabled, the bus cannot enter low-power state
4. On a large number of SoCs, if the bus not in a low-power state, S0ix
cannot be entered, which in turn prevents the SoC from entering
suspend.
Fix by re-enabling LPM negotiation in the device's suspend callback.
Suggested-by: Stanislaw Kardach <skardach@google.com>
Fixes: f9e5b33934ce ("mmc: host: Improve I/O read/write performance for GL9763E")
Cc: stable@vger.kernel.org
Signed-off-by: Sven van Ashbrook <svenva@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230831160055.v3.1.I7ed1ca09797be2dd76ca914c57d88b32d24dac88@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
tuning only support in 4-bit mode or 8 bit mode, so in 1-bit mode,
need to hold retuning.
Find this issue when use manual tuning method on imx93. When system
resume back, SDIO WIFI try to switch back to 4 bit mode, first will
trigger retuning, and all tuning command failed.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: dfa13ebbe334 ("mmc: host: Add facility to support re-tuning")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230830093922.3095850-1-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull modules updates from Luis Chamberlain:
"Summary of the changes worth highlighting from most interesting to
boring below:
- Christoph Hellwig's symbol_get() fix to Nvidia's efforts to
circumvent the protection he put in place in year 2020 to prevent
proprietary modules from using GPL only symbols, and also ensuring
proprietary modules which export symbols grandfather their taint.
That was done through year 2020 commit 262e6ae7081d ("modules:
inherit TAINT_PROPRIETARY_MODULE"). Christoph's new fix is done by
clarifing __symbol_get() was only ever intended to prevent module
reference loops by Linux kernel modules and so making it only find
symbols exported via EXPORT_SYMBOL_GPL(). The circumvention tactic
used by Nvidia was to use symbol_get() to purposely swift through
proprietary module symbols and completely bypass our traditional
EXPORT_SYMBOL*() annotations and community agreed upon
restrictions.
A small set of preamble patches fix up a few symbols which just
needed adjusting for this on two modules, the rtc ds1685 and the
networking enetc module. Two other modules just needed some build
fixing and removal of use of __symbol_get() as they can't ever be
modular, as was done by Arnd on the ARM pxa module and Christoph
did on the mmc au1xmmc driver.
This is a good reminder to us that symbol_get() is just a hack to
address things which should be fixed through Kconfig at build time
as was done in the later patches, and so ultimately it should just
go.
- Extremely late minor fix for old module layout 055f23b74b20
("module: check for exit sections in layout_sections() instead of
module_init_section()") by James Morse for arm64. Note that this
layout thing is old, it is *not* Song Liu's commit ac3b43283923
("module: replace module_layout with module_memory"). The issue
however is very odd to run into and so there was no hurry to get
this in fast.
- Although the fix did not go through the modules tree I'd like to
highlight the fix by Peter Zijlstra in commit 54097309620e
("x86/static_call: Fix __static_call_fixup()") now merged in your
tree which came out of what was originally suspected to be a
fallout of the the newer module layout changes by Song Liu commit
ac3b43283923 ("module: replace module_layout with module_memory")
instead of module_init_section()"). Thanks to the report by
Christian Bricart and the debugging by Song Liu & Peter that turned
to be noted as a kernel regression in place since v5.19 through
commit ee88d363d156 ("x86,static_call: Use alternative RET
encoding").
I highlight this to reflect and clarify that we haven't seen more
fallout from ac3b43283923 ("module: replace module_layout with
module_memory").
- RISC-V toolchain got mapping symbol support which prefix symbols
with "$" to help with alignment considerations for disassembly.
This is used to differentiate between incompatible instruction
encodings when disassembling. RISC-V just matches what ARM/AARCH64
did for alignment considerations and Palmer Dabbelt extended
is_mapping_symbol() to accept these symbols for RISC-V. We already
had support for this for all architectures but it also checked for
the second character, the RISC-V check Dabbelt added was just for
the "$". After a bit of testing and fallout on linux-next and based
on feedback from Masahiro Yamada it was decided to simplify the
check and treat the first char "$" as unique for all architectures,
and so we no make is_mapping_symbol() for all archs if the symbol
starts with "$".
The most relevant commit for this for RISC-V on binutils was:
https://sourceware.org/pipermail/binutils/2021-July/117350.html
- A late fix by Andrea Righi (today) to make module zstd
decompression use vmalloc() instead of kmalloc() to account for
large compressed modules. I suspect we'll see similar things for
other decompression algorithms soon.
- samples/hw_breakpoint minor fixes by Rong Tao, Arnd Bergmann and
Chen Jiahao"
* tag 'modules-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
module/decompress: use vmalloc() for zstd decompression workspace
kallsyms: Add more debug output for selftest
ARM: module: Use module_init_layout_section() to spot init sections
arm64: module: Use module_init_layout_section() to spot init sections
module: Expose module_init_layout_section()
modules: only allow symbol_get of EXPORT_SYMBOL_GPL modules
rtc: ds1685: use EXPORT_SYMBOL_GPL for ds1685_rtc_poweroff
net: enetc: use EXPORT_SYMBOL_GPL for enetc_phc_index
mmc: au1xmmc: force non-modular build and remove symbol_get usage
ARM: pxa: remove use of symbol_get()
samples/hw_breakpoint: mark sample_hbp as static
samples/hw_breakpoint: fix building without module unloading
samples/hw_breakpoint: Fix kernel BUG 'invalid opcode: 0000'
modpost, kallsyms: Treat add '$'-prefixed symbols as mapping symbols
kernel: params: Remove unnecessary ‘0’ values from err
module: Ignore RISC-V mapping symbols too
|
|
The polarity of the card detection gpio is handled by the "cd-inverted"
property in the device tree. Move this inversion logic to gpiolib to avoid
reading the gpio raw value.
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230825095157.76073-4-balamanikandan.gunasundar@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Move the contents of linux/atmel-mci.h into
drivers/mmc/host/atmel-mci.c as it is only used in one file
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20230825095157.76073-3-balamanikandan.gunasundar@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Replace the legacy GPIO APIs with gpio descriptor consumer interface.
To maintain backward compatibility, we rely on the "cd-inverted"
property to manage the invertion flag instead of GPIO property.
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230825095157.76073-2-balamanikandan.gunasundar@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
First of all, Unisoc's IC provides cmd delay and read delay to ensure
that the host can get the correct data. However, according to SD Spec,
there is no need to do tuning in high speed mode, but with the
development of chip processes, it is more and more difficult to find
a suitable delay to cover all the chips. Therefore, we need SD high
speed mode online tuning.
In addition, we added mmc_sd_switch() and mmc_send_status() to the
header file to allow it to be usable by the driver.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Link: https://lore.kernel.org/r/20230825091743.15613-3-wenchao.chen@unisoc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
To support the need for host specific tuning for SD high-speed mode, let's
add two new optional callbacks, ->prepare|execute_sd_hs_tuning() and let's
call them when switching into the SD high-speed mode.
Note that, during the tuning process it's also needed for host drivers to
send commands to the SD card to verify that the tuning process succeeds.
Therefore, let's also share the corresponding functions from the core to
allow this.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Link: https://lore.kernel.org/r/20230825091743.15613-2-wenchao.chen@unisoc.com
[Ulf: Dropped unnecessary function declarations and updated the commit msg]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This commit implements the runtime PM operations to disable eMMC card clock
when idle.
Reviewed-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: Liming Sun <limings@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230822195929.168552-2-limings@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This commit adds handling in dwcmshc_resume() for different error
cases.
Signed-off-by: Liming Sun <limings@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230822195929.168552-1-limings@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty") into tty-next
We need the serial-core fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Errata ERR010450 only shows up if voltage is 1.8V, but if the device is
supplied by 3v3 the errata can be ignored. So let's check for if quirk
SDHCI_QUIRK2_NO_1_8_V is defined or not before limiting the frequency.
Cc: Jim Reinhart <jimr@tekvox.com>
Cc: James Autry <jautry@tekvox.com>
Cc: Matthew Maron <matthewm@tekvox.com>
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Acked-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230811214853.8623-1-giulio.benetti@benettiengineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Now that sdhci_pltfm_unregister() has been removed, rename
sdhci_pltfm_register() to sdhci_pltfm_init_and_add_host() to better
reflect what it does.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-17-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Now that sdhci_pltfm_unregister() is unused, remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-16-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-15-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-14-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-13-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-12-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-11-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-10-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-9-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-8-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-7-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-5-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() so that
devm_clk_get_optional_enabled() can be used for pltfm_host->clk.
This has the side effect that the order of operations on the error path
and remove path is not the same as it was before, but should be safe
nevertheless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sdhci_pltfm_remove() instead of sdhci_pltfm_unregister() because
sdhci_pltfm_unregister() is going to be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811130351.7038-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
