| Age | Commit message (Collapse) | Author |
|---|
|
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when Intel host controllers wait for the present
state to propagate.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
|
This patch adds support for HS200 tuning mode on AMD eMMC-4.5.1
Reviewed-by: Sen, Pankaj <Pankaj.Sen@amd.com>
Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reviewed-by: Agrawal, Nitesh-kumar <Nitesh-kumar.Agrawal@amd.com>
Signed-off-by: S-k, Shyam-sundar <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
cd_con_id is not used and always NULL.
Remove it to make code a bit more cleaner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
On NI 9037 boards the max SDIO frequency is limited by trace lengths
and other layout choices. The max SDIO frequency is stored in an ACPI
table.
The driver reads the ACPI entry MXFQ during sdio_probe_slot and sets the
f_max field of the host.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Jaeden Amero <jaeden.amero@ni.com>
Reviewed-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add PCI ID for Intel byt sdio host controller sub-vended by NI.
The controller has different behavior because of the board layout NI
puts it on.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
With commit f35bbf61ab77 ("gpio / ACPI: Return -EPROBE_DEFER if the
gpiochip was not found"), a gpio descriptor request can now be deferred if
the providing gpio host controller driver hasn't been loaded yet. Allow use
in mmc slot probe in order to prevent card detect gpio setup from failing
in this case.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support for eMMC/SD/SDIO Intel GLK host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some Intel controllers (e.g. BXT) might fail to set bus power after a
D3 -> D0 transition due to the present state not yet having propagated.
Retry for up to 2 milliseconds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Let devices define their own sdhci_ops so that device-specific variations
can be implemented without adding quirks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Set MMC_CAP_CMD_DURING_TFR for Intel BYT and related eMMC host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Intel Merrifield provides an interface to an external SD card.
Enable it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Intel Merrifield is known to have an SDIO interface and on Intel Edison board a
WiFi card is wired to it.
Enable the interface here to allow WiFi card enumeration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Refactor intel_mrfld_mmc_probe_slot() to use switch case. The change allows to
add a support for SD and SDIO interfaces without any pain.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The commit 52ac7acf412b ("mmc: sdhci-pci: Convert to use managed functions
pcim_* and devm_*") converted ->probe() / ->remove() functions to use device
managed resource API. Here is a follow up to cover sdhci_pci_probe_slot() and
sdhci_pci_remove_slot().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Convert to define the system PM callbacks to be build for CONFIG_PM_SLEEP
and use the SET_SYSTEM_SLEEP_PM_OPS. In this way the code becomes cleaner.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Everywhere else in the code MRFLD abbreviation is used for Intel Merrifield. Do
the same for sdhci-pci.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
At the successful conclusion of sdhci_pci_probe(), if runtime pm was
allowed, the device would be runtime suspended. That wastes a lot of time
during initialization. Instead leave the device active until the mmc core
scans for a card.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The CMD19/CMD14 bus width test has been found to be unreliable in
some cases. It is not essential, so simply remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Set MMC_CAP_AGGRESSIVE_PM for Broxton host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit 9250aea76bfc ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support and PCI IDs for more Broxton host controllers
Other BXT IDs were added in v4.4 so cc'ing stable. This patch
is dependent on commit 163cbe31e516 ("mmc: sdhci-pci: Fix card
detect race for Intel BXT/APL") but that is already in stable
since v4.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
DMA mask will already be set by sdhci_set_dma_mask(), which
is equivalent to the removed code since pci_set_dma_mask()
expands to its DMA-API counterpart.
There should also be no reason to set the DMA mask after probe.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In some cases, the stronger 33 Ohm driver strength must not be used
so it is not a suitable default. Change it to the standard default
50 Ohm value.
The patch applies to v4.2+ except the file name changed. It is
drivers/mmc/host/sdhci-pci.c prior to v.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add PCI IDs for Intel host controllers
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add another PCI ID for an Intel eMMC host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
drivers/mmc/host/sdhci-pci-core.c:447:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sdhci-pci-o2micro.c contains no initialisation and its functions are only
called from shdci-pci.c, so there is no reason for it to be a separate
module, let alone or for it to always be built-in.
- Rename sdhci-pci.c to sdhci-pci-core.c so that the sdhci-pci module
can be built from multiple source files
- Add sdhci-pci-o2micro.c to it
- Remove redundant exports
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
