| Age | Commit message (Collapse) | Author |
|---|
|
The /** at the start indicates that these are kernel-doc comments, but
really these are just regular comments.
Replace /** by /* to avoid a large number of warnings from kernel-doc.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Suggested-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Give typo in kernel-doc documentation: hdr -> hrd
Fixes this warning:
drivers/media/platform/allegro-dvt/nal-h264.h:33: warning: expecting prototype for struct nal_h264_hdr_parameters. Prototype was for struct
nal_h264_hrd_parameters instead
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The Allegro Codec supports HEVC encoding. The messages to the MCU are
the same for H.264 and HEVC, but some options have to be changed. These
are actually only a few options.
The driver, however, must add the HEVC VPS/SPS/PPS NAL Units to the
coded stream and must properly provide the HEVC format and controls to
user space.
[hverkuil: fix warning for wrong enum type (h264 instead of hevc)]
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
These controls are specific to H.264 and shall only be activated, if the
coded format is H.264.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The HEVC Non-VCL NAL units require more space than the H.264 Non-VCL NAL
units. Therefore, the driver needs to reserve more space in front of the
actual coded data that is written by the hardware codec.
Increase the offset that shall be used by the hardware codec from 64
bytes to 128 bytes which is as arbitrary as before.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The maximum bitrate and the size of the CPB are dependent on the level.
As the levels differ between the different codecs, the functions to get
the maximum bitrate and CPB must be codec specific, too.
Rename the functions to make it obvious that the function are only valid
for H.264.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The driver only supports CAVLC for H.264, but HEVC only uses CABAC. As
the driver has to explicitly tell the MCU to use CABAC for HEVC, add a
helper function to get the entropy mode.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
V4L2 specifies different controls for the QP values of different codecs.
Simplify users that just care for the QP values by providing accessor
function that return the correct control based on the currently set
codec.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The profile and level are straight copies from the v4l2-ctrls. Avoid
duplication and directly read the value of the v4l2-ctrl.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The cpb_size and the gop_size are straight copies of the values in the
v4l2-ctrls. To avoid this duplication, directly get the values from the
v4l2-ctrls and remove the copies.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The cbp_size_value_minus1 in the SPS can scaled using cpb_size_scale to
reduce the number of bits necessary to encode the value. For simplicity,
the scaling was set to 1.
Restructure to the code to make it easier to drop the cbp_size from the
channel and as we are at it, also properly implement the scaling.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As the driver now uses the v4l2-ctrls to setup the channel, there is no
need to explicitly set the bitrate. The initial bitrate is now set via
the same path as if it is set from userspace using the v4l2-ctrl.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
v4l2_ctrl_handler_setup() calls s_ctrl for all controls of the handler.
This ensures that the channel is initialized using the default values of
the v4l2-ctrls.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The log2_max_poc field is used to set log2_max_pic_order_cnt_lsb_minus4
for the coded stream. It has an allowed range of 0 to 12.
param contains the value without the minus4, but since firmware
version 2019.1, the value has to be log2_max_pic_order_cnt_lsb - 1,
presumably to fit the maximum value of 16 into a 4 bit field.
The driver does not support firmware version 2019.1. Thus, change the
behaviour starting from firmware version 2019.2.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There are several encoding options that are hard coded in the parameter
that is used to configure the hardware codec. However, some of the
options must be written to the SPS/PPS by the driver. Furthermore, some
of the options depend on the codec that is used (i.e. H.264 or HEVC).
Therefore, move options that depend on the codec to the channel and add
constants for options that are independent of the codec but must be
written to the SPS/PPS.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
A format change (i.e. the frame size or the codec) has multiple effects
on a channel:
- The available controls
- The limits of the available controls
- The default encoding options
To avoid scattering the changes all over the driver, add a new function
that goes over the channel and does all required adjustments.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In order to support different codecs, the driver must support changing
the format on CAPTURE. Therefore, the driver needs to handle S_FMT on
CAPTURE.
As the driver will have a different number of formats for OUTPUT and
CAPTURE, split the check for the format index in ENUM_FMT into CAPTURE
and OUTPUT.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
When encoding a video as HEVC, the allegro driver needs to generate the
Non-VCL NAL units for HEVC. Do the same as for H.264 and add a module
that takes C structs for the VPS/SPS/PPS and encodes the fields as RBPS
as specified by "ITU-T Rec. H.265 (02/2018) high efficiency video
coding".
[hverkuil: add missing static for nal_hevc_write/read_start_code_prefix]
[hverkuil: fix typo: pps -> vps in nal_hevc_write_vps]
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Allow generators to explicitly signal an error if the C structs contain
unsupported or invalid fields.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The RBSP structure is the same for HEVC and H.264. In order to be able
to reuse the RBSP handler for generating HEVC NAL units, extract the
functions from the H.264 generator.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The dst_handle field in the PUT_STREAM_BUFFER and ENCODE_FRAME_RESPONSE
is used to retrieve the V4L2 CAPTURE buffer. Calling it stream_id is
confusing. Call it dst_handle inspired by src_handle for the OUTPUT
buffer.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The v4l2-m2m has various helpers for correctly handle the draining. Drop
the driver specific state machine and use the m2m helper functions.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The stateful encoder API was finalized. Nothing is blocking the driver
from being moved out of staging.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
