summaryrefslogtreecommitdiff
path: root/drivers/media/i2c/ov5640.c
AgeCommit message (Collapse)Author
2023-05-25media: ov5640: Drop dead code using frame_intervalJacopo Mondi
The ov5640_update_pixel_rate() function handles the parallel and MIPI CSI-2 cases separately. When running on a parallel setup the V4L2_CID_PIXEL_RATE value is calculated at the beginning of the function using the values configured with the frame_interval operations, and then the function immediately returns. The remaining of the function handles the MIPI CSI-2 configuration and should not use the 'current_fr' and 'def_fps' fields as those are only relevant for parallel mode. Drop a small section of dead code that updates vblank using frame_interval on a MIPI CSI-2 setup. Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
2023-05-25media: ov5640: Remove unused 'framerate' parameterJacopo Mondi
The 'current framerate' parameter passed to ov5640_try_fmt_internal() is unsued. Drop it. Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
2023-05-25media: ov5640: correct comments for default VGA to avoid confusionGuoniu.zhou
When OV5640 work at DVP mode, the default initialization settings make it output 30 frames per second. But when it work at CSI-2 mode the default link frequency will make it output 60 frames per second, so correct the comments to make it more clear. Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
2023-05-25media: Switch i2c drivers back to use .probe()Uwe Kleine-König
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type"), all drivers being converted to .probe_new() and then commit 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert back to (the new) .probe() to be able to eventually drop .probe_new() from struct i2c_driver. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
2023-02-06media: ov5640: Fix analogue gain controlPaul Elder
Gain control is badly documented in publicly available (including leaked) documentation. There is an AGC pre-gain in register 0x3a13, expressed as a 6-bit value (plus an enable bit in bit 6). The driver hardcodes it to 0x43, which one application note states is equal to x1.047. The documentation also states that 0x40 is equel to x1.000. The pre-gain thus seems to be expressed as in 1/64 increments, and thus ranges from x1.00 to x1.984. What the pre-gain does is however unspecified. There is then an AGC gain limit, in registers 0x3a18 and 0x3a19, expressed as a 10-bit "real gain format" value. One application note sets it to 0x00f8 and states it is equal to x15.5, so it appears to be expressed in 1/16 increments, up to x63.9375. The manual gain is stored in registers 0x350a and 0x350b, also as a 10-bit "real gain format" value. It is documented in the application note as a Q6.4 values, up to x63.9375. One version of the datasheet indicates that the sensor supports a digital gain: The OV5640 supports 1/2/4 digital gain. Normally, the gain is controlled automatically by the automatic gain control (AGC) block. It isn't clear how that would be controlled manually. There appears to be no indication regarding whether the gain controlled through registers 0x350a and 0x350b is an analogue gain only or also includes digital gain. The words "real gain" don't necessarily mean "combined analogue and digital gains". Some OmniVision sensors (such as the OV8858) are documented as supoprting different formats for the gain values, selectable through a register bit, and they are called "real gain format" and "sensor gain format". For that sensor, we have (one of) the gain registers documented as 0x3503[2]=0, gain[7:0] is real gain format, where low 4 bits are fraction bits, for example, 0x10 is 1x gain, 0x28 is 2.5x gain If 0x3503[2]=1, gain[7:0] is sensor gain format, gain[7:4] is coarse gain, 00000: 1x, 00001: 2x, 00011: 4x, 00111: 8x, gain[7] is 1, gain[3:0] is fine gain. For example, 0x10 is 1x gain, 0x30 is 2x gain, 0x70 is 4x gain (The second part of the text makes little sense) "Real gain" may thus refer to the combination of the coarse and fine analogue gains as a single value. The OV5640 0x350a and 0x350b registers thus appear to control analogue gain. The driver incorrectly uses V4L2_CID_GAIN as V4L2 has a specific control for analogue gain, V4L2_CID_ANALOGUE_GAIN. Use it. If registers 0x350a and 0x350b are later found to control digital gain as well, the driver could then restrict the range of the analogue gain control value to lower than x64 and add a separate digital gain control. Signed-off-by: Paul Elder <paul.elder@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Reviewed-by: Jai Luthra <j-luthra@ti.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2023-02-06media: ov5640: Handle delays when no reset_gpio setJai Luthra
Some module manufacturers [1][2] don't expose the RESETB and PWDN pins of the sensor directly through the 15-pin FFC connector. Instead wiring ~PWDN gpio to the sensor pins with appropriate delays. In such cases, reset_gpio will not be available to the driver, but it will still be toggled when the sensor is powered on, and thus we should still honor the wait time of >= 5ms + 1ms + 20ms (see figure 2-3 in [3]) before attempting any i/o operations over SCCB. Also, rename the function to ov5640_powerup_sequence to better match the datasheet (section 2.7). [1] https://digilent.com/reference/_media/reference/add-ons/pcam-5c/pcam_5c_sch.pdf [2] https://www.alinx.com/public/upload/file/AN5641_User_Manual.pdf [3] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf Fixes: 19a81c1426c1 ("[media] add Omnivision OV5640 sensor driver") Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Jai Luthra <j-luthra@ti.com> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2023-02-06media: ov5640: Fix soft reset sequence and timingsJai Luthra
Move the register-based reset out of the init_setting[] and into the powerup_sequence function. The sensor is power cycled and reset using the gpio pins so the soft reset is not always necessary. This also ensures that soft reset honors the timing sequence from the datasheet [1]. [1] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf Fixes: 19a81c1426c1 ("[media] add Omnivision OV5640 sensor driver") Reported-by: Nishanth Menon <nm@ti.com> Suggested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Signed-off-by: Jai Luthra <j-luthra@ti.com> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonaboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2023-02-06media: ov5640: Update last busy timestamp to reset autosuspend timerAndrey Skvortsov
Otherwise autosuspend delay doesn't work and power is cut off immediately as device is freed. Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2023-02-03media: ov5640: set correct default format for CSI-2 modeGuoniu.zhou
In commit a89f14bbcfa5 ("media: ov5640: Split DVP and CSI-2 formats"), it splits format list for DVP and CSI-2 mode, but the default format defined in commit 90b0f355c5a3 ("media: ov5640: Implement init_cfg") is only supported by DVP mode, so define a new default format for CSI-2 mode. Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com> Reviewed-by: Jai Luthra <j-luthra@ti.com> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-12-06media: ov5640: report correct frame rate to userGuoniu.zhou
In commit 3145efcdb4d0 ("media: ov5640: Rework timings programming"), it defines max_fps field in ov5640_mode_info structure to store maximum frame rate supported by each mode. But in ov5640_try_frame_interval(), it assumes the maximum frame rate supported by all modes is 60. But actually, only VGA support it. For others, the maximum frame rate supported is 30. So correct it by taking the maximum frame rate supported by each mode as the initialization value of the local variable maxfps. Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-12-06media: ov5640: set correct default link frequencyGuoniu.zhou
current_link_freq field in ov5640_dev structure is link frequency, not link frequency array index, so correct it. Fixes: 3c28588f35d3 ("media: ov5640: Update pixel_rate and link_freq") Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com> Acked-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-10-22Merge tag 'media/v6.1-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media Pull missed media updates from Mauro Carvalho Chehab: "It seems I screwed-up my previous pull request: it ends up that only half of the media patches that were in linux-next got merged in -rc1. The script which creates the signed tags silently failed due to 5.19->6.0 so it ended generating a tag with incomplete stuff. So here are the missing parts: - a DVB core security fix - lots of fixes and cleanups for atomisp staging driver - old drivers that are VB1 are being moved to staging to be deprecated - several driver updates - mostly for embedded systems, but there are also some things addressing issues with some PC webcams, in the UVC video driver" * tag 'media/v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (163 commits) media: sun6i-csi: Move csi buffer definition to main header file media: sun6i-csi: Introduce and use video helper functions media: sun6i-csi: Add media ops with link notify callback media: sun6i-csi: Remove controls handler from the driver media: sun6i-csi: Register the media device after creation media: sun6i-csi: Pass and store csi device directly in video code media: sun6i-csi: Tidy up video code media: sun6i-csi: Tidy up v4l2 code media: sun6i-csi: Tidy up Kconfig media: sun6i-csi: Use runtime pm for clocks and reset media: sun6i-csi: Define and use variant to get module clock rate media: sun6i-csi: Always set exclusive module clock rate media: sun6i-csi: Tidy up platform code media: sun6i-csi: Refactor main driver data structures media: sun6i-csi: Define and use driver name and (reworked) description media: cedrus: Add a Kconfig dependency on RESET_CONTROLLER media: sun8i-rotate: Add a Kconfig dependency on RESET_CONTROLLER media: sun8i-di: Add a Kconfig dependency on RESET_CONTROLLER media: sun4i-csi: Add a Kconfig dependency on RESET_CONTROLLER media: sun6i-csi: Add a Kconfig dependency on RESET_CONTROLLER ...
2022-09-24media: ov5640: Use runtime PMPaul Elder
Switch to using runtime PM for power management. Make it optional, however, to support ACPI. Signed-off-by: Paul Elder <paul.elder@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-08-16i2c: Make remove callback return voidUwe Kleine-König
The value returned by an i2c driver's remove function is mostly ignored. (Only an error message is printed if the value is non-zero that the error is ignored.) So change the prototype of the remove function to return no value. This way driver authors are not tempted to assume that passing an error to the upper layer is a good idea. All drivers are adapted accordingly. There is no intended change of behaviour, all callbacks were prepared to return 0 before. Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com> Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au> Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Crt Mori <cmo@melexis.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013 Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/* Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5 Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860 Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power Acked-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-07-08media: ov5640: Move format mux config in formatJacopo Mondi
The image format produced by the sensor is controlled by two registers, whose values computation is open coded in ov5640_set_framefmt(). As we have a list of formats already, move the OV5640_REG_FORMAT_CONTROL00 and OV5640_REG_ISP_FORMAT_MUX_CTRL register values to the static list of formats instead of open coding it. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Split DVP and CSI-2 formatsJacopo Mondi
The format enumeration list is shared between CSI-2 and DVP modes. This lead to the enumeration of unsupported format variants in both modes. Separate the list of DVP and CSI-2 formats and create helpers to access the correct one. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Adjust format to bpp in s_fmtJacopo Mondi
The ov5640 driver supports different sizes for different mbus_codes. In particular: - 8bpp modes: high resolution sizes (>= 1280x720) - 16bpp modes: all sizes - 24bpp modes: low resolutions sizes (< 1280x720) Adjust the image sizes according to the above constraints. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Restrict sizes to mbus codeJacopo Mondi
The ov5640 driver supports different sizes for different mbus_codes. In particular: - 8bpp modes: high resolution sizes (>= 1280x720) - 16bpp modes: all sizes - 24bpp modes: low resolutions sizes (< 1280x720) Restrict the frame sizes enumerations to the above constraints. While at it, make sure the fse->mbus_code parameter is valid, and return -EINVAL if it's not. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add BGR888 formatJacopo Mondi
Add support for BGR888 image format. No existing media bus codes describe exactly the way data is transferred on the CSI-2 bus. This is not a new issue, the CSI-2 YUV422 8-bit format is described by MEDIA_BUS_FMT_UYVY8_1X16 which is an arbitrary convention and not an exact match. Use the MEDIA_BUS_FMT_BGR888_1X24 to follow the same convention, based on the order in which bits are transmitted over the CSI-2 bus when producing images in RGB24 format. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add RGB565_1X16 formatJacopo Mondi
The driver already supports the 2X8_[LE|BE] variants of RGB565 formats. As for CSI-2 the 2X8 variants do not apply, add RGB565_1X16 variant with little-endian ordering of components as required by the CSI-2 specifications. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Register device propertiesJacopo Mondi
Parse the device properties and register the rotation and orientation V4L2 controls using v4l2_ctrl_new_fwnode_properties(). Remove the open-coded parsing of the rotation property and assume the DTS is correct is providing either <0> or <180> as possible rotations. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Implement get_selectionJacopo Mondi
Implement the get_selection pad operation for the OV5640 sensor driver. The supported targets report the sensor's native size, the active pixel array size and the analog crop rectangle from which the image is produced. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Implement init_cfgJacopo Mondi
Implement the init_cfg pad operation to initialize the subdev state format to the default one. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Change CSI-2 timings to comply with FPSJacopo Mondi
Now that the frame duration can be controlled by tuning the VBLANK duration in CSI-2 mode, fix all modes definitions to comply with the reported FPS. All modes run at 30 FPS except for full-resolution mode 2592x1944 which runs at 15FPS. Tested on a 2 data lanes setup in UYVY and RGB565 modes in CSI-2 mode. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Remove frame rate check from find_mode()Jacopo Mondi
The current implementation of ov5640_find_mode() fails if the frame rate programmed with s_frame_interval doesn't match the maximum frame rate for the current mode. This causes issues when moving from one mode with higher FPS to another one which only supports a lower FPS range with tools like media-ctl. It also forces users that do not use s_frame_interval(), but rather configure blankings explicitly, to adjust the programmed FPS range to avoid failures. For this reason, remove the FPS check from ov5640_find_mode() and only perform it at s_frame_interval() time. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Adjust vblank with s_frame_intervalHugues Fruchet
Adjust the vertical blanking when s_frame_interval is used. s_frame_interval allows to set a fixed frame rate, which gets stored as the sensor's current one. When a new mode is applied, the current frame rate is reset to the mode's default one. In order to correctly report the currently configured vertical blanking for s_frame_interval users, verify that the desired frame rate has not been changed. If that's the case, compute the correct blanking value and reflect it through the corresponding v4l2 control. Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add VBLANK controlJacopo Mondi
Add the VBLANK control which allows to select the duration of the frame vertical blankings and allows to control the framerate. The VBLANK control also modifies the exposure time range, which cannot exceed the maximum frame length. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add HBLANK controlJacopo Mondi
Add the HBLANK control as read-only. The hblank value is fixed in the mode definition and is updated everytime a new format is applied. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Remove ov5640_mode_init_dataJacopo Mondi
The ov5640_mode_init_data is a fictional sensor more which is used to program the initial sensor settings. It is only used to initialize the sensor and can be replaced it with a throw-away mode which just wraps the register table. Also rename the register table to drop the format from the name to make it clear an actual sensor mode has to be applied after the initial programming. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Remove duplicated mode settingsJacopo Mondi
The register tables for all resolutions smaller than 720p are now identical. Remove the duplicated ones and create a single ov5640_setting_low_res[] register table. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Re-sort per-mode register tablesJacopo Mondi
The per-mode register tables are not sorted by size. Fix it. Cosmetic change only. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Provide timings accessorJacopo Mondi
Provide a function to shortcut access to the correct timings definition to avoid repeating the same pattern when accessing the sensor timings. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Split DVP and CSI-2 timingsJacopo Mondi
Separate the timings for the DVP mode from the timings for the CSI-2 mode in the ov5640 modes definition. The CSI-2 timings will deviate from the DVP ones as the clock tree is calculated differently. In CSI-2 mode change the analog crop rectangles as the OV5640 pixel array is composed as: - vertically: 16 dummy columns, 2592 valid ones and 16 dummy columns for a total of 2624 columns - horizontally: 8 optical black lines, 6 dummy ones, 1944 valid and 6 dummies for a total of 1964 lines Adjust the analog crop rectangle in CSI-2 mode to: - Skip the first 16 dummy columns - Skip the first 14 black/dummy lines - Pass the whole valid pixel array size to the ISP for all modes except 1024x768, 720p and 1080p which are obtained by cropping the valid pixel array. Tested in RGB565, UYVY and RGB888 modes in CSI-2 mode. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Fix 720x480 in RGB888 modeJacopo Mondi
Adjust the left crop of 720x480 to enable capture in RGB888 format, which is otherwise broken. The 56 pixels alignment has been copied from the 720x576 mode. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Rework timings programmingJacopo Mondi
The current definition of a sensor mode defines timings as follows: - hact, vact: Visible width and height - htot, vtot: Total sizes including blankings This makes difficult to clearly separate the visible sizes from the blankings and to make the vertical blanking programmable. Rework the sensor modes sizes definition to: - Report the analog crop sizes - Report the visible crop size - Report the total pixels per line as HBLANK is fixed - Report the VBLANK value to make it programmable Also modify the ov5640_set_timings() function to program all the windowing registers are remove them from the per-mode register-value tables. Do not change the timing values from the ones reported in the register tables to maintain bisectability. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Rework CSI-2 clock treeJacopo Mondi
Re-work the ov5640_set_mipi_pclk() function to calculate the PLL configuration using the pixel_rate and link_freq values set at s_fmt time. Rework the DVP clock mode settings to calculate the pixel clock internally and remove the assumption on the 16bpp format. Tested in MIPI CSI-2 mode with 1 and 2 data lanes with: - all the sensor supported resolutions in UYVY, RGB565 and MJPEG formats. - resolutions >= 1280x720 in RAW Bayer format. - resolutions < 1280x720 in RGB888 format. [Rework pclk_period and link_freq computation] Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Update pixel_rate and link_freqJacopo Mondi
After having set a new format re-calculate the pixel_rate and link_freq control values and update them when in MIPI mode. Take into account the limitation of the link frequency having to be strictly smaller than 1GHz when computing the desired link_freq, and adjust the resulting pixel_rate acounting for the clock tree configuration. [Adjust link_freq calculation] Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add LINK_FREQ controlJacopo Mondi
Add the V4L2_CID_LINK_FREQ control to the ov5640 driver. Make the control read-only for the moment. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Associate bpp with formatsJacopo Mondi
Associate the bit depth to each format supported by the sensor. The bpp will be used to calculate the line length. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add ov5640_is_csi2() functionJacopo Mondi
Checking if the sensor is used in DVP or MIPI CSI-2 mode is a repeated pattern which is about to be repeated more often. Provide an inline function to shortcut that. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5604: Re-arrange modes definitionJacopo Mondi
The array of supported modes is close to unreadable. Re-arrange it giving it some room to breath. Cosmetic change only. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add pixel rate to modesJacopo Mondi
Add to each mode supported by the sensor the ideal pixel rate, as defined by Table 2.1 in the chip manual. The ideal pixel rate will be used to compute the MIPI CSI-2 clock tree. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-02-23media: ov5640: Fix set format, v4l2_mbus_pixelcode not updatedMirela Rabulea
In ov5640_set_fmt, pending_fmt_change will always be false, because the sensor format is saved before comparing it with the previous format: fmt = &sensor->fmt;... *fmt = *mbus_fmt;... if (mbus_fmt->code != sensor->fmt.code) sensor->pending_fmt_change = true; This causes the sensor to capture with the previous pixelcode. Also, changes might happen even for V4L2_SUBDEV_FORMAT_TRY, so fix that. Basically, revert back to the state before commit 071154499193 ("media: ov5640: Fix set format regression") as it was more clear, and then update format even when pixelcode does not change, as resolution might change. Fixes: 071154499193 ("media: ov5640: Fix set format regression") Fixes: 6949d864776e ("media: ov5640: do not change mode if format or frame interval is unchanged") Fixes: fb98e29ff1ea5 ("media: ov5640: fix mode change regression") Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com> Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Acked-by: Hugues Fruchet <hugues.fruchet@st.com> Tested-by: Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
2021-08-04media: ov5640: Complement yuv mbus formats with their 1X16 versionsXavier Roumegue
According to media bus pixel codes definition, data formats on serial busses should be described with one bus sample per pixel. Documentation/userspace-api/media/v4l/subdev-formats.rst states: "The media bus pixel codes document parallel formats. Should the pixel data be transported over a serial bus, the media bus pixel code that describes a parallel format that transfers a sample on a single clock cycle is used. For instance, both MEDIA_BUS_FMT_BGR888_1X24 and MEDIA_BUS_FMT_BGR888_3X8 are used on parallel busses for transferring an 8 bits per sample BGR data, whereas on serial busses the data in this format is only referred to using MEDIA_BUS_FMT_BGR888_1X24. This is because there is effectively only a single way to transport that format on the serial busses." Some MIPI CSI receivers strictly obey this definition and declare support for only *1X_* formats. Hence, complement the supported media bus formats with their 1X16 versions (currently applicable to yuyv, uyvy) to enhance interoperability with CSI receivers. Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-06-17media: v4l2-subdev: add subdev-wide state structTomi Valkeinen
We have 'struct v4l2_subdev_pad_config' which contains configuration for a single pad used for the TRY functionality, and an array of those structs is passed to various v4l2_subdev_pad_ops. I was working on subdev internal routing between pads, and realized that there's no way to add TRY functionality for routes, which is not pad specific configuration. Adding a separate struct for try-route config wouldn't work either, as e.g. set-fmt needs to know the try-route configuration to propagate the settings. This patch adds a new struct, 'struct v4l2_subdev_state' (which at the moment only contains the v4l2_subdev_pad_config array) and the new struct is used in most of the places where v4l2_subdev_pad_config was used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config are changed to instead take v4l2_subdev_state. The changes to drivers/media/v4l2-core/v4l2-subdev.c and include/media/v4l2-subdev.h were written by hand, and all the driver changes were done with the semantic patch below. The spatch needs to be applied to a select list of directories. I used the following shell commands to apply the spatch: dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media" for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done Note that Coccinelle chokes on a few drivers (gcc extensions?). With minor changes we can make Coccinelle run fine, and these changes can be reverted after spatch. The diff for these changes is: For drivers/media/i2c/s5k5baf.c: @@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd, &s5k5baf_cis_rect, v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS), v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS), - v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT) + v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT), }; s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r); return 0; For drivers/media/platform/s3c-camif/camif-capture.c: @@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd, *mf = camif->mbus_fmt; break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* crop rectangle at camera interface input */ mf->width = camif->camif_crop.width; mf->height = camif->camif_crop.height; @@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd, } break; - case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P: + case CAMIF_SD_PAD_SOURCE_C: /* Pixel format can be only changed on the sink pad. */ mf->code = camif->mbus_fmt.code; mf->width = crop->width; The semantic patch is: // <smpl> // Change function parameter @@ identifier func; identifier cfg; @@ func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...) { <... - cfg + sd_state ...> } // Change function declaration parameter @@ identifier func; identifier cfg; type T; @@ T func(..., - struct v4l2_subdev_pad_config *cfg + struct v4l2_subdev_state *sd_state , ...); // Change function return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...) { ... } // Change function declaration return value @@ identifier func; @@ - struct v4l2_subdev_pad_config + struct v4l2_subdev_state *func(...); // Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it // inside a pad_state. @@ identifier func; identifier pad_cfg; @@ func(...) { ... struct v4l2_subdev_pad_config pad_cfg; + struct v4l2_subdev_state pad_state = { .pads = &pad_cfg }; <+... ( v4l2_subdev_call | sensor_call | isi_try_fse | isc_try_fse | saa_call_all ) (..., - &pad_cfg + &pad_state ,...) ...+> } // If the function uses fields from pad_config, access via state->pads @@ identifier func; identifier state; @@ func(..., struct v4l2_subdev_state *state , ...) { <... ( - state->try_fmt + state->pads->try_fmt | - state->try_crop + state->pads->try_crop | - state->try_compose + state->pads->try_compose ) ...> } // If the function accesses the filehandle, use fh->state instead @@ struct v4l2_subdev_fh *fh; @@ - fh->pad + fh->state @@ struct v4l2_subdev_fh fh; @@ - fh.pad + fh.state // Start of vsp1 specific @@ @@ struct vsp1_entity { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... }; @@ symbol entity; @@ vsp1_entity_init(...) { ... entity->config = - v4l2_subdev_alloc_pad_config + v4l2_subdev_alloc_state (&entity->subdev); ... } @@ symbol entity; @@ vsp1_entity_destroy(...) { ... - v4l2_subdev_free_pad_config + v4l2_subdev_free_state (entity->config); ... } @exists@ identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)"; symbol config; @@ func(...) { ... - struct v4l2_subdev_pad_config *config; + struct v4l2_subdev_state *config; ... } // End of vsp1 specific // Start of rcar specific @@ identifier sd; identifier pad_cfg; @@ rvin_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } // End of rcar specific // Start of rockchip specific @@ identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)"; symbol rsz; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = rsz->pad_cfg }; ... - rsz->pad_cfg + &state ... } @@ identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)"; symbol isp; symbol pad_cfg; @@ func(...) { + struct v4l2_subdev_state state = { .pads = isp->pad_cfg }; ... - isp->pad_cfg + &state ... } @@ symbol rkisp1; symbol isp; symbol pad_cfg; @@ rkisp1_isp_register(...) { + struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg }; ... - rkisp1->isp.pad_cfg + &state ... } // End of rockchip specific // Start of tegra-video specific @@ identifier sd; identifier pad_cfg; @@ __tegra_channel_try_format(...) { ... - struct v4l2_subdev_pad_config *pad_cfg; + struct v4l2_subdev_state *sd_state; ... - pad_cfg = v4l2_subdev_alloc_pad_config(sd); + sd_state = v4l2_subdev_alloc_state(sd); <... - pad_cfg + sd_state ...> - v4l2_subdev_free_pad_config(pad_cfg); + v4l2_subdev_free_state(sd_state); ... } @@ identifier sd_state; @@ __tegra_channel_try_format(...) { ... struct v4l2_subdev_state *sd_state; <... - sd_state->try_crop + sd_state->pads->try_crop ...> } // End of tegra-video specific // </smpl> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-04-06media: v4l: fwnode: Rename v4l2_async_register_subdev_sensor_commonSakari Ailus
Rename v4l2_async_register_subdev_sensor_common as v4l2_async_register_subdev_sensor. This is a part of the effort to make the long names present in V4L2 fwnode and async frameworks shorter. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-11-16media: ov5640: fix support of BT656 bus modeHugues Fruchet
Fix PCLK polarity not being taken into account. Add comments about BT656 register control. Remove useless ov5640_set_stream_bt656() function. Refine comments about MIPI IO register control. Fixes: 4039b03720f7 ("media: i2c: ov5640: Add support for BT656 mode") Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-11-16media: ov5640: add support of 160x120 resolutionHugues Fruchet
Add support of 160x120 resolution. Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-09-10media: i2c: ov5640: Fail probe on unsupported bus_typeLad Prabhakar
Fail probe if unsupported bus_type is detected. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-09-10media: i2c: ov5640: Add support for BT656 modeLad Prabhakar
Enable support for BT656 mode. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-30 13:27:20 +0000