| Age | Commit message (Collapse) | Author |
|---|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
commit 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Also dev_err_probe message require a trailing \n.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Both sensors are quite similar. Their specs only differ regarding LVDS
and parallel output but are identical regarding MIPI-CSI-2 interface.
But they use a different init setting of hard-coded values, taken from
the datasheet.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
imx290_start_streaming logs what failed, but not the error
code from that function. Add it into the log message.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The sensor supports H & V flips, so add the relevant hooks for
V4L2_CID_HFLIP and V4L2_CID_VFLIP to configure them.
Note that the Bayer order is maintained as the readout area
shifts by 1 pixel in the appropriate direction (note the
comment about the top margin being 8 pixels whilst the bottom
margin is 9). The V4L2_SEL_TGT_CROP region is therefore
adjusted appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The sensor supports either a 37.125 or 74.25MHz external, but
the driver only supported 37.125MHz.
Add the relevant register configuration for either clock
frequency option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
IMX290_CTRL_07 was written from both imx290_global_init_settings
and imx290_1080p_settings and imx290_720p_settings.
Remove it from imx290_global_init_settings as the setting varies
based on the mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The default VMAX for 60fps in 720p mode is 750 according to the
datasheet, however the driver always left it at 1125 thereby stopping
60fps being achieved.
Make VMAX (and therefore V4L2_CID_VBLANK) mode dependent so that 720p60
can be achieved.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The driver exposed V4L2_CID_VBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
V4L2_CID_VBLANK also sets the limits for the exposure control,
therefore exposure ranges have to be updated when vblank changes
(either via s_ctrl, or via changing mode).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The driver exposed V4L2_CID_HBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" added support for the increased link frequencies
on 2 data lanes, but didn't update the CSI timing registers in
accordance with the datasheet.
Use the specified settings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Commit "97589ad61c73 media: i2c: imx290: Add support for 2 data lanes"
added support for running in two lane mode (instead of 4), but
without changing the link frequency that resulted in a max of 30fps.
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" then doubled the link frequency when in 2 lane mode,
but didn't undo the correction for running at only 30fps, just extending
horizontal blanking instead.
Remove the 30fps limit on 2 lane by correcting the register config
in accordance with the datasheet for 60fps operation over 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The datasheet lists the link frequency changes between
1080p and 720p modes. This is correct that the link frequency
changes as measured on an oscilloscope.
Link frequency is not necessarily the same as pixel rate.
The datasheet gives standard configurations for 1080p and 720p
modes at a number of frame rates.
Looking at the 1080p mode it gives:
HMAX = 0x898 = 2200
VMAX = 0x465 = 1125
2200 * 1125 * 60fps = 148.5MPix/s
Looking at the 720p mode it gives:
HMAX = 0xce4 = 3300
VMAX = 0x2ee = 750
3300 * 750 * 60fps = 148.5Mpix/s
This driver currently scales the pixel rate proportionally to the
link frequency, however the above shows that this is not the
correct thing to do, and currently all frame rate and exposure
calculations give incorrect results.
Correctly report the pixel rate as being 148.5MPix/s under any
mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Any V4L2 subdevice that implements controls and declares
V4L2_SUBDEV_FL_HAS_DEVNODE should also declare V4L2_SUBDEV_FL_HAS_EVENTS
and implement subscribe_event and unsubscribe_event hooks.
This driver didn't and would therefore fail v4l2-compliance
testing.
Add the relevant hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The colorspace fields were left untouched in imx290_set_fmt
which lead to a v4l2-compliance failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Fix up a couple of coding style issues regarding missing blank
lines after declarations, double blank lines, and incorrect
indentation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The IMX290 module is available as either mono or colour (Bayer).
Update the driver so that it can advertise the correct mono
formats instead of the colour ones.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
No need to call fwnode_property_read_u32(dev_fwnode()), when
we have already existing helper. So use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Since we have a proper endianness converters for LE 24-bit data use them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The runtime suspend/resume functions are only referenced from the
dev_pm_ops, but they use the old SET_RUNTIME_PM_OPS() helper
that requires a __maybe_unused annotation to avoid a warning:
drivers/media/i2c/imx290.c:1082:12: error: unused function 'imx290_runtime_resume' [-Werror,-Wunused-function]
static int imx290_runtime_resume(struct device *dev)
^
drivers/media/i2c/imx290.c:1090:12: error: unused function 'imx290_runtime_suspend' [-Werror,-Wunused-function]
static int imx290_runtime_suspend(struct device *dev)
^
Convert this to the new RUNTIME_PM_OPS() helper that so this
is not required. To improve this further, also use the pm_ptr()
helper that lets the dev_pm_ops get dropped entirely when
CONFIG_PM is disabled.
A related mistake happened in the of_match_ptr() macro here, which
like SET_RUNTIME_PM_OPS() requires the match table to be marked
as __maybe_unused, though I could not reproduce building this without
CONFIG_OF. Remove the of_match_ptr() here as there is no point in
dropping the match table in configurations without CONFIG_OF.
Fixes: 02852c01f654 ("media: i2c: imx290: Initialize runtime PM before subdev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Check the error status returned by imx290_set_data_lanes() in its
caller and propagate it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
There's no need to check for an incorrect number of data lanes in
imx290_set_data_lanes() as the value is validated at probe() time. Drop
the check.
The PHY_LANE_NUM and CSI_LANE_MODE registers are programmed with a value
equal to the number of lanes minus one. Compute it instead of handling
it in the switch/case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
There's no need to configure the data lanes in the runtime PM resume
handler. Do so in imx290_start_streaming() instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Initializing the subdev before runtime PM means that no subdev
initialization can interact with the runtime PM framework. This can be
problematic when modifying controls, as the .s_ctrl() handler commonly
calls pm_runtime_get_if_in_use(). These code paths are not trivial,
making the driver fragile and possibly causing subtle bugs.
To make the subdev initialization more robust, initialize runtime PM
first.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Use runtime PM autosuspend to avoid powering off the sensor during fast
stop-reconfigure-restart cycles. This also fixes runtime PM handling in
the probe function that didn't suspend the device, effectively leaving
it resumed forever.
While at it, improve documentation of power management in probe() and
remove().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The imx290_pixfmt structure contains information about formats,
currently limited to the bpp value. Extend it with the register settings
for each format, and rename it to imx290_format_info to make its purpose
clearer. Add a function named imx290_format_info() to look up format
info for a media bus code, and use it through the code. This allows
dropping the imx290 bpp field as the value is now looked up dynamically.
The error handling in imx290_setup_format() can also be dropped, as the
format is guaranteed by imx290_set_fmt() to be valid.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Use the V4L2 subdev active state API to store the active format. This
simplifies the driver not only by dropping the imx290 current_format
field, but it also allows dropping the imx290 lock, replaced with the
state lock.
The lock check in imx290_ctrl_update() can be dropped as
imx290_set_fmt() can't be called anywmore with which set to ACTIVE
before controls are initialized.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Move the external clock initialization code from probe() to a separate
function to improve readability. No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Improve error handling in the probe() function with dev_err_probe().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Make the probe() function more readable by factoring out the DT parsing
code to a separate function. No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The black level programmed in the BLKLEVEL register depends on the
output format. The black level value computation is currently performed
in imx290_set_ctrl(), in addition to having different black level values
in the output-specific register value tables. Move it to a separate
function to simplify the imx290_set_ctrl() code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The hblank, vblank, pixel rate and link frequency values and limits are
currently computed when creating controls, in imx290_ctrl_init(), and
updated in imx290_ctrl_update(). This duplicates the logic in different
places. Simplify the code by setting the control values and limits to
hardcoded values when creating the controls, and call
imx290_ctrl_update() to then update them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Avoid accessing the imx290 current_format and current_mode fields in
imx290_calc_pixel_rate() to prepare for the removal of those fields.
Among the two callers of the function, imx290_ctrl_update() has an
explicit mode pointer already, and we can also give it a format pointer.
Use those explicitly.
While at it, inline the imx290_get_link_freq() function in
imx290_calc_pixel_rate() as it is only called there.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The imx290_get_link_freq_index() function hides the fact that it relies
on the imx290 current_mode field, which obfuscates the code instead of
making it more readable. Inline it in the callers, and use the mode
pointer we already have in imx290_ctrl_update() instead of using the
current_mode field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Move the control update code to a separate function to group it with all
the control-related code and make imx290_set_fmt() more readable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The probe() function is large. Make it more readable by factoring the
subdev initialization code out. While at it, rename the error labels as
the "free_" prefix isn't accurate.
No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Move functions around to group them in logical sections, in order to
improve readability. As a result, the IMX290_NUM_SUPPLIES macro has to
be changed. No other code change is included, only moves.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The IMX290 gain register controls the analogue gain. Replace the
V4L2_CID_GAIN control with V4L2_CID_ANALOGUE_GAIN.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Implement read-only access to crop selection rectangles to expose the
analogue crop rectangle. The public (leaked) IMX290 documentation is not
very clear on how cropping is implemented and configured exactly, so
the margins may not be entirely accurate.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The driver duplicates the same pattern to access the try or active
format in multiple locations. Factor it out to a separate function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Registers 0x3012, 0x3013 and 0x3480 are not documented and are set in
the per-mode register arrays with values indentical for all modes. Move
them to the common array.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Create the V4L2_CID_ORIENTATION and V4L2_CID_ROTATION controls to
expose the corresponding fwnode properties.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Add support for the V4L2_CID_HBLANK and V4L2_CID_VBLANK controls to the
imx290 driver. Make the controls read-only to start with, to report the
values to userspace for timing calculation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The imx290_probe() function is too large. Split control initialzation to
a dedicated function to increase code readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The gain is expressed in multiple of 0.3dB, as a value between 0.0dB
and 72.0dB. Gains between 0.0dB and 30.0dB (included) apply analog gain
only, higher gains from 30.3dB to 72dB apply additional digital gain.
The maximum gain value is erroneously set to 72. Increase it to 100 to
cover the whole analog gain range. Support for digital gain can be added
separately if needed.
The IMX327 and IMX462 are largely compatible with the IMX290, but have
an analog gain range of 0.0dB to 29.4dB and 42dB of digital gain. When
support for those sensors gets added to the driver, the gain control
should be adjusted accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Support configuring the exposure time, which is expressed as the
complement of the exposure time (frame period minus integration time).
The frame period is currently fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Define macros for all registers programmed by the driver for which
documentation is available to increase readability. This starts making
use of 16-bit registers in the register arrays, so the value field has
to be increased to 32 bits.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Error handling for register writes requires checking the error status of
every single write. This makes the code complex, or incorrect when the
checks are omitted. Simplify this by passing a pointer to an error code
to the imx290_write_reg() function, which allows writing multiple
registers in a row and only checking for errors at the end.
While at it, rename imx290_write_reg() to imx290_write() as there's
nothing else than registers to write, and rename imx290_read_reg()
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Define registers with the appropriate size, using the variable-size
register access mechanism that has just been introduced. This simplifies
the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The IMX290 has registers of different sizes. To simplify the code,
handle this in the read/write functions instead of in the callers by
encoding the register size in the symbolic name macros. All registers
are defined as 8-bit for now, a subsequent change will move to larger
registers where applicable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
