| Age | Commit message (Collapse) | Author |
|---|
|
Before we write stripe data to raid disks, we must guarantee stripe data
is settled down in log disk. To do this, we flush log disk cache and
wait the flush finish. That wait introduces sleep time in raid5d thread
and impact performance. This patch moves the log disk cache flush
process to the stripe handling state machine, which can remove the wait
in raid5d.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
crc32c has lower overhead with cpu acceleration. It's a shame I didn't
use it in first post, sorry. This changes disk format, but we are still
ok in current stage.
V2: delete unnecessary type conversion as pointed out by Bart
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
This is the log recovery support. The process is quite straightforward.
We scan the log and read all valid meta/data/parity into memory. If a
stripe's data/parity checksum is correct, the stripe will be recoveried.
Otherwise, it's discarded and we don't scan the log further. The reclaim
process guarantees stripe which starts to be flushed raid disks has
completed data/parity and has correct checksum. To recovery a stripe, we
just copy its data/parity to corresponding raid disks.
The trick thing is superblock update after recovery. we can't let
superblock point to last valid meta block. The log might look like:
| meta 1| meta 2| meta 3|
meta 1 is valid, meta 2 is invalid. meta 3 could be valid. If superblock
points to meta 1, we write a new valid meta 2n. If crash happens again,
new recovery will start from meta 1. Since meta 2n is valid, recovery
will think meta 3 is valid, which is wrong. The solution is we create a
new meta in meta2 with its seq == meta 1's seq + 10 and let superblock
points to meta2. recovery will not think meta 3 is a valid meta,
because its seq is wrong
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
This is the reclaim support for raid5 log. A stripe write will have
following steps:
1. reconstruct the stripe, read data/calculate parity. ops_run_io
prepares to write data/parity to raid disks
2. hijack ops_run_io. stripe data/parity is appending to log disk
3. flush log disk cache
4. ops_run_io run again and do normal operation. stripe data/parity is
written in raid array disks. raid core can return io to upper layer.
5. flush cache of all raid array disks
6. update super block
7. log disk space used by the stripe can be reused
In practice, several stripes consist of an io_unit and we will batch
several io_unit in different steps, but the whole process doesn't
change.
It's possible io return just after data/parity hit log disk, but then
read IO will need read from log disk. For simplicity, IO return happens
at step 4, where read IO can directly read from raid disks.
Currently reclaim run if there is specific reclaimable space (1/4 disk
size or 10G) or we are out of space. Reclaim is just to free log disk
spaces, it doesn't impact data consistency. The size based force reclaim
is to make sure log isn't too big, so recovery doesn't scan log too
much.
Recovery make sure raid disks and log disk have the same data of a
stripe. If crash happens before 4, recovery might/might not recovery
stripe's data/parity depending on if data/parity and its checksum
matches. In either case, this doesn't change the syntax of an IO write.
After step 3, stripe is guaranteed recoverable, because stripe's
data/parity is persistent in log disk. In some cases, log disk content
and raid disks content of a stripe are the same, but recovery will still
copy log disk content to raid disks, this doesn't impact data
consistency. space reuse happens after superblock update and cache
flush.
There is one situation we want to avoid. A broken meta in the middle of
a log causes recovery can't find meta at the head of log. If operations
require meta at the head persistent in log, we must make sure meta
before it persistent in log too. The case is stripe data/parity is in
log and we start write stripe to raid disks (before step 4). stripe
data/parity must be persistent in log before we do the write to raid
disks. The solution is we restrictly maintain io_unit list order. In
this case, we only write stripes of an io_unit to raid disks till the
io_unit is the first one whose data/parity is in log.
The io_unit list order is important for other cases too. For example,
some io_unit are reclaimable and others not. They can be mixed in the
list, we shouldn't reuse space of an unreclaimable io_unit.
Includes fixes to problems which were...
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
This introduces a simple log for raid5. Data/parity writing to raid
array first writes to the log, then write to raid array disks. If
crash happens, we can recovery data from the log. This can speed up
raid resync and fix write hole issue.
The log structure is pretty simple. Data/meta data is stored in block
unit, which is 4k generally. It has only one type of meta data block.
The meta data block can track 3 types of data, stripe data, stripe
parity and flush block. MD superblock will point to the last valid
meta data block. Each meta data block has checksum/seq number, so
recovery can scan the log correctly. We store a checksum of stripe
data/parity to the metadata block, so meta data and stripe data/parity
can be written to log disk together. otherwise, meta data write must
wait till stripe data/parity is finished.
For stripe data, meta data block will record stripe data sector and
size. Currently the size is always 4k. This meta data record can be made
simpler if we just fix write hole (eg, we can record data of a stripe's
different disks together), but this format can be extended to support
caching in the future, which must record data address/size.
For stripe parity, meta data block will record stripe sector. It's
size should be 4k (for raid5) or 8k (for raid6). We always store p
parity first. This format should work for caching too.
flush block indicates a stripe is in raid array disks. Fixing write
hole doesn't need this type of meta data, it's for caching extension.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
