| Age | Commit message (Collapse) | Author |
|---|
|
commit 28a9a9e83ceae2cee25b9af9ad20d53aaa9ab951 upstream
Packet queue state is over used to determine SDMA descriptor
availablitity and packet queue request state.
cpu 0 ret = user_sdma_send_pkts(req, pcount);
cpu 0 if (atomic_read(&pq->n_reqs))
cpu 1 IRQ user_sdma_txreq_cb calls pq_update() (state to _INACTIVE)
cpu 0 xchg(&pq->state, SDMA_PKT_Q_ACTIVE);
At this point pq->n_reqs == 0 and pq->state is incorrectly
SDMA_PKT_Q_ACTIVE. The close path will hang waiting for the state
to return to _INACTIVE.
This can also change the state from _DEFERRED to _ACTIVE. However,
this is a mostly benign race.
Remove the racy code path.
Use n_reqs to determine if a packet queue is active or not.
Cc: <stable@vger.kernel.org> # 4.9.0
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 074fca3a18e7e1e0d4d7dcc9d7badc43b90232f4 ]
Currently, for IB_WR_LOCAL_INV WR, when the next fence is None, the
current fence will be SMALL instead of Normal Fence.
Without this patch krping doesn't work on CX-5 devices and throws
following error:
The error messages are from CX5 driver are: (from server side)
[ 710.434014] mlx5_0:dump_cqe:278:(pid 2712): dump error cqe
[ 710.434016] 00000000 00000000 00000000 00000000
[ 710.434016] 00000000 00000000 00000000 00000000
[ 710.434017] 00000000 00000000 00000000 00000000
[ 710.434018] 00000000 93003204 100000b8 000524d2
[ 710.434019] krping: cq completion failed with wr_id 0 status 4 opcode 128 vender_err 32
Fixed the logic to set the correct fence type.
Fixes: 6e8484c5cf07 ("RDMA/mlx5: set UMR wqe fence according to HCA cap")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit db7a691a1551a748cb92d9c89c6b190ea87e28d5 upstream.
If the firmware reports a connection width that is not 1x, 4x, 8x or 12x
it causes the driver to fail during initialization.
To prevent this failure every time a new width is introduced to the RDMA
stack, we will set a default 4x width for these widths which ar unknown to
the driver.
This is needed to allow to run old kernels with new firmware.
Cc: <stable@vger.kernel.org> # 4.1
Fixes: 1b5daf11b015 ("IB/mlx5: Avoid using the MAD_IFC command under ISSI > 0 mode")
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0e0cb82804a6a21d9067022c2dfdf80d11da429 upstream.
pq_update() can only be called in two places: from the completion
function when the complete (npkts) sequence of packets has been
submitted and processed, or from setup function if a subset of the
packets were submitted (i.e. the error path).
Currently both paths can call pq_update() if an error occurrs. This
race will cause the n_req value to go negative, hanging file_close(),
or cause a crash by freeing the txlist more than once.
Several variables are used to determine SDMA send state. Most of
these are unnecessary, and have code inspectible races between the
setup function and the completion function, in both the send path and
the error path.
The request 'status' value can be set by the setup or by the
completion function. This is code inspectibly racy. Since the status
is not needed in the completion code or by the caller it has been
removed.
The request 'done' value races between usage by the setup and the
completion function. The completion function does not need this.
When the number of processed packets matches npkts, it is done.
The 'has_error' value races between usage of the setup and the
completion function. This can cause incorrect error handling and leave
the n_req in an incorrect value (i.e. negative).
Simplify the code by removing all of the unneeded state checks and
variables.
Clean up iovs node when it is freed.
Eliminate race conditions in the error path:
If all packets are submitted, the completion handler will set the
completion status correctly (ok or aborted).
If all packets are not submitted, the caller must wait until the
submitted packets have completed, and then set the completion status.
These two change eliminate the race condition in the error path.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3dc7c7badb7502ec3e3aa817a8bdd9e53aa54c52 ]
Before returning -EPERM we should release some resources, as already done
in the other error handling path of the function.
Fixes: d8f9cc328c88 ("IB/mlx4: Mark user MR as writable if actual virtual memory is writable")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e7b169f34403becd3c9fd3b6e46614ab788f2187 ]
During QP creation, the mlx5 driver translates the QP type to an
internal value which is passed on to FW. There was no check to make
sure that the translated value is valid, and -EINVAL was coerced into
the mailbox command.
Current firmware refuses this as an invalid QP type, but future/past
firmware may do something else.
Fixes: 09a7d9eca1a6c ('{net,IB}/mlx5: QP/XRCD commands via mlx5 ifc')
Reviewed-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0dbfaa9f2813787679e296eb5476e40938ab48c8 upstream.
The SL specified by a user needs to be a valid SL.
Add a range check to the user specified SL value which protects from
running off the end of the SL to SC table.
CC: stable@vger.kernel.org
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d623500b3c4efd8d4e945ac9003c6b87b469a9ab upstream.
If a packet stream uses an UnsupportedVL (virtual lane), the send
engine will not send the packet, and it will not indicate that an
error has occurred. This will cause the packet stream to block.
HFI has 8 virtual lanes available for packet streams. Each lane can
be enabled or disabled using the UnsupportedVL mask. If a lane is
disabled, adding a packet to the send context must be disallowed.
The current mask for determining unsupported VLs defaults to 0 (allow
all). This is incorrect. Only the VLs that are defined should be
allowed.
Determine which VLs are disabled (mtu == 0), and set the appropriate
unsupported bit in the mask. The correct mask will allow the send
engine to error on the invalid VL, and error recovery will work
correctly.
Cc: <stable@vger.kernel.org> # 4.9.x+
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94694d18cf27a6faad91487a38ce516c2b16e7d9 upstream.
If the number of packets in a user sdma request does not match
the actual iovectors being sent, sdma_cleanup can be called on
an uninitialized request structure, resulting in a crash similar
to this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffffc0ae8bb7>] __sdma_txclean+0x57/0x1e0 [hfi1]
PGD 8000001044f61067 PUD 1052706067 PMD 0
Oops: 0000 [#1] SMP
CPU: 30 PID: 69912 Comm: upsm Kdump: loaded Tainted: G OE
------------ 3.10.0-862.el7.x86_64 #1
Hardware name: Intel Corporation S2600KPR/S2600KPR, BIOS
SE5C610.86B.01.01.0019.101220160604 10/12/2016
task: ffff8b331c890000 ti: ffff8b2ed1f98000 task.ti: ffff8b2ed1f98000
RIP: 0010:[<ffffffffc0ae8bb7>] [<ffffffffc0ae8bb7>] __sdma_txclean+0x57/0x1e0
[hfi1]
RSP: 0018:ffff8b2ed1f9bab0 EFLAGS: 00010286
RAX: 0000000000008b2b RBX: ffff8b2adf6e0000 RCX: 0000000000000000
RDX: 00000000000000a0 RSI: ffff8b2e9eedc540 RDI: ffff8b2adf6e0000
RBP: ffff8b2ed1f9bad8 R08: 0000000000000000 R09: ffffffffc0b04a06
R10: ffff8b331c890190 R11: ffffe6ed00bf1840 R12: ffff8b3315480000
R13: ffff8b33154800f0 R14: 00000000fffffff2 R15: ffff8b2e9eedc540
FS: 00007f035ac47740(0000) GS:ffff8b331e100000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 0000000c03fe6000 CR4: 00000000001607e0
Call Trace:
[<ffffffffc0b0570d>] user_sdma_send_pkts+0xdcd/0x1990 [hfi1]
[<ffffffff9fe75fb0>] ? gup_pud_range+0x140/0x290
[<ffffffffc0ad3105>] ? hfi1_mmu_rb_insert+0x155/0x1b0 [hfi1]
[<ffffffffc0b0777b>] hfi1_user_sdma_process_request+0xc5b/0x11b0 [hfi1]
[<ffffffffc0ac193a>] hfi1_aio_write+0xba/0x110 [hfi1]
[<ffffffffa001a2bb>] do_sync_readv_writev+0x7b/0xd0
[<ffffffffa001bede>] do_readv_writev+0xce/0x260
[<ffffffffa022b089>] ? tty_ldisc_deref+0x19/0x20
[<ffffffffa02268c0>] ? n_tty_ioctl+0xe0/0xe0
[<ffffffffa001c105>] vfs_writev+0x35/0x60
[<ffffffffa001c2bf>] SyS_writev+0x7f/0x110
[<ffffffffa051f7d5>] system_call_fastpath+0x1c/0x21
Code: 06 49 c7 47 18 00 00 00 00 0f 87 89 01 00 00 5b 41 5c 41 5d 41 5e 41 5f
5d c3 66 2e 0f 1f 84 00 00 00 00 00 48 8b 4e 10 48 89 fb <48> 8b 51 08 49 89 d4
83 e2 0c 41 81 e4 00 e0 00 00 48 c1 ea 02
RIP [<ffffffffc0ae8bb7>] __sdma_txclean+0x57/0x1e0 [hfi1]
RSP <ffff8b2ed1f9bab0>
CR2: 0000000000000008
There are two exit points from user_sdma_send_pkts(). One (free_tx)
merely frees the slab entry and one (free_txreq) cleans the sdma_txreq
prior to freeing the slab entry. The free_txreq variation can only be
called after one of the sdma_init*() variations has been called.
In the panic case, the slab entry had been allocated but not inited.
Fix the issue by exiting through free_tx thus avoiding sdma_clean().
Cc: <stable@vger.kernel.org> # 4.9.x+
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
commit 308aa2b8f7b7db3332a7d41099fd37851fb793b2 upstream.
Once the qp has been flushed, it cannot be flushed again. The user qp
flush logic wasn't enforcing it however. The bug can cause
touch-after-free crashes like:
Unable to handle kernel paging request for data at address 0x000001ec
Faulting instruction address: 0xc008000016069100
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c008000016069100] flush_qp+0x80/0x480 [iw_cxgb4]
LR [c00800001606cd6c] c4iw_modify_qp+0x71c/0x11d0 [iw_cxgb4]
Call Trace:
[c00800001606cd6c] c4iw_modify_qp+0x71c/0x11d0 [iw_cxgb4]
[c00800001606e868] c4iw_ib_modify_qp+0x118/0x200 [iw_cxgb4]
[c0080000119eae80] ib_security_modify_qp+0xd0/0x3d0 [ib_core]
[c0080000119c4e24] ib_modify_qp+0xc4/0x2c0 [ib_core]
[c008000011df0284] iwcm_modify_qp_err+0x44/0x70 [iw_cm]
[c008000011df0fec] destroy_cm_id+0xcc/0x370 [iw_cm]
[c008000011ed4358] rdma_destroy_id+0x3c8/0x520 [rdma_cm]
[c0080000134b0540] ucma_close+0x90/0x1b0 [rdma_ucm]
[c000000000444da4] __fput+0xe4/0x2f0
So fix flush_qp() to only flush the wq once.
Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a1ceeca679dccc492235f0f629d9e9f7b3d51ca8 ]
hns bitmap allocation functions return 0 on success and -1 on failure.
Callers of these functions wrongly used their return value as an errno,
fix that by making a proper conversion.
Fixes: a598c6f4c5a8 ("IB/hns: Simplify function of pd alloc and qp alloc")
Signed-off-by: Gal Pressman <pressmangal@gmail.com>
Acked-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d63c46734c545ad0488761059004a65c46efdde3 ]
Fix memory leak in the error path of mlx5_ib_create_srq() by making sure
to free the allocated srq.
Fixes: c2b37f76485f ("IB/mlx5: Fix integer overflows in mlx5_ib_create_srq")
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 062d0f22a30c39840ea49b72cfcfc1aa4cc538fa upstream.
In write to debugfs file 'resource_stats' the local buffer 'tmp_str' is
written at index 'count-1' where 'count' is the size of the write, so
potentially 0.
This patch filters odd values for the write size/position to avoid this
type of problem.
Signed-off-by: Michael Mera <dev@michaelmera.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8f9cc328c8888369880e2527e9186d745f2bbf6 upstream.
To allow rereg_user_mr to modify the MR from read-only to writable without
using get_user_pages again, we needed to define the initial MR as writable.
However, this was originally done unconditionally, without taking into
account the writability of the underlying virtual memory.
As a result, any attempt to register a read-only MR over read-only
virtual memory failed.
To fix this, do not add the writable flag bit when the user virtual memory
is not writable (e.g. const memory).
However, when the underlying memory is NOT writable (and we therefore
do not define the initial MR as writable), the IB core adds a
"force writable" flag to its user-pages request. If this succeeds,
the reg_user_mr caller gets a writable copy of the original pages.
If the user-space caller then does a rereg_user_mr operation to enable
writability, this will succeed. This should not be allowed, since
the original virtual memory was not writable.
Cc: <stable@vger.kernel.org>
Fixes: 9376932d0c26 ("IB/mlx4_ib: Add support for user MR re-registration")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b697d7d8c741f27b728a878fc55852b06d0f6f5e upstream.
The __get_txreq() function can return a pointer, ERR_PTR(-EBUSY), or NULL.
All of the relevant call sites look for IS_ERR, so the NULL return would
lead to a NULL pointer exception.
Do not use the ERR_PTR mechanism for this function.
Update all call sites to handle the return value correctly.
Clean up error paths to reflect return value.
Fixes: 45842abbb292 ("staging/rdma/hfi1: move txreq header code")
Cc: <stable@vger.kernel.org> # 4.9.x+
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b72717a20bba8bdd01b14c0460be7d15061cd6b upstream.
The code was mistakenly using the length of the page array memory instead
of the depth of the page array.
This would cause MR creation to fail in some cases.
Fixes: 8376b86de7d3 ("iw_cxgb4: Support the new memory registration API")
Cc: stable@vger.kernel.org
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1bc0299d976e000ececc6acd76e33b4582646cb7 upstream.
The following code fails to allocate a buffer for the
tail address that the hardware DMAs into when the user
context DMA_RTAIL is set.
if (HFI1_CAP_KGET_MASK(rcd->flags, DMA_RTAIL)) {
rcd->rcvhdrtail_kvaddr = dma_zalloc_coherent(
&dd->pcidev->dev, PAGE_SIZE, &dma_hdrqtail,
gfp_flags);
if (!rcd->rcvhdrtail_kvaddr)
goto bail_free;
rcd->rcvhdrqtailaddr_dma = dma_hdrqtail;
}
So the rcvhdrtail_kvaddr would then be NULL.
The mmap logic fails to check for a NULL rcvhdrtail_kvaddr.
The fix is to test for both user and kernel DMA_TAIL options
during the allocation as well as testing for a NULL
rcvhdrtail_kvaddr during the mmap processing.
Additionally, all downstream testing of the capmask for DMA_RTAIL
have been eliminated in favor of testing rcvhdrtail_kvaddr.
Cc: <stable@vger.kernel.org> # 4.9.x
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b1ca7ece15e94251d1d0d919f813943e4a58059 upstream.
There is no need to crash the machine if unknown work request was
received in SQP MAD.
Cc: <stable@vger.kernel.org> # 3.6
Fixes: 37bfc7c1e83f ("IB/mlx4: SR-IOV multiplex and demultiplex MADs")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b74a83cf54a3747e22c57e25712bd70eef8acee upstream.
On fatal error the driver simulates CQE's for ULPs that rely on
completion of all their posted work-request.
For the GSI traffic, the mlx5 has its own mechanism that sends the
completions via software CQE's directly to the relevant CQ.
This should be kept in fatal error too, so the driver should simulate
such CQE's with the specified error state in order to complete GSI QP
work requests.
Without the fix the next deadlock might appears:
schedule_timeout+0x274/0x350
wait_for_common+0xec/0x240
mcast_remove_one+0xd0/0x120 [ib_core]
ib_unregister_device+0x12c/0x230 [ib_core]
mlx5_ib_remove+0xc4/0x270 [mlx5_ib]
mlx5_detach_device+0x184/0x1a0 [mlx5_core]
mlx5_unload_one+0x308/0x340 [mlx5_core]
mlx5_pci_err_detected+0x74/0xe0 [mlx5_core]
Cc: <stable@vger.kernel.org> # 4.7
Fixes: 89ea94a7b6c4 ("IB/mlx5: Reset flow support for IB kernel ULPs")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d3e71136a080d007620472f50c7b3e63ba0f5cf upstream.
A warm restart will fail to unload the driver, leaving link state
potentially flapping up to the point the BIOS resets the adapter.
Correct the issue by hooking the shutdown pci method,
which will bring port down.
Cc: <stable@vger.kernel.org> # 4.9.x
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0252f73334f9ef68868e4684200bea3565a4fcee upstream.
The following error occurs in a debug build when running MPI PSM:
[ 307.415911] WARNING: CPU: 4 PID: 23867 at lib/dma-debug.c:1158
check_unmap+0x4ee/0xa20
[ 307.455661] ib_qib 0000:05:00.0: DMA-API: device driver failed to check map
error[device address=0x00000000df82b000] [size=4096 bytes] [mapped as page]
[ 307.517494] Modules linked in:
[ 307.531584] ib_isert iscsi_target_mod ib_srpt target_core_mod rpcrdma
sunrpc ib_srp scsi_transport_srp scsi_tgt ib_iser libiscsi ib_ipoib
scsi_transport_iscsi rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm
ib_qib intel_powerclamp coretemp rdmavt intel_rapl iosf_mbi kvm_intel kvm
irqbypass crc32_pclmul ghash_clmulni_intel ipmi_ssif ib_core aesni_intel sg
ipmi_si lrw gf128mul dca glue_helper ipmi_devintf iTCO_wdt gpio_ich hpwdt
iTCO_vendor_support ablk_helper hpilo acpi_power_meter cryptd ipmi_msghandler
ie31200_edac shpchp pcc_cpufreq lpc_ich pcspkr ip_tables xfs libcrc32c sd_mod
crc_t10dif crct10dif_generic mgag200 i2c_algo_bit drm_kms_helper syscopyarea
sysfillrect sysimgblt fb_sys_fops ttm ahci crct10dif_pclmul crct10dif_common
drm crc32c_intel libahci tg3 libata serio_raw ptp i2c_core
[ 307.846113] pps_core dm_mirror dm_region_hash dm_log dm_mod
[ 307.866505] CPU: 4 PID: 23867 Comm: mpitests-IMB-MP Kdump: loaded Not
tainted 3.10.0-862.el7.x86_64.debug #1
[ 307.911178] Hardware name: HP ProLiant DL320e Gen8, BIOS J05 11/09/2013
[ 307.944206] Call Trace:
[ 307.956973] [<ffffffffbd9e915b>] dump_stack+0x19/0x1b
[ 307.982201] [<ffffffffbd2a2f58>] __warn+0xd8/0x100
[ 308.005999] [<ffffffffbd2a2fdf>] warn_slowpath_fmt+0x5f/0x80
[ 308.034260] [<ffffffffbd5f667e>] check_unmap+0x4ee/0xa20
[ 308.060801] [<ffffffffbd41acaa>] ? page_add_file_rmap+0x2a/0x1d0
[ 308.090689] [<ffffffffbd5f6c4d>] debug_dma_unmap_page+0x9d/0xb0
[ 308.120155] [<ffffffffbd4082e0>] ? might_fault+0xa0/0xb0
[ 308.146656] [<ffffffffc07761a5>] qib_tid_free.isra.14+0x215/0x2a0 [ib_qib]
[ 308.180739] [<ffffffffc0776bf4>] qib_write+0x894/0x1280 [ib_qib]
[ 308.210733] [<ffffffffbd540b00>] ? __inode_security_revalidate+0x70/0x80
[ 308.244837] [<ffffffffbd53c2b7>] ? security_file_permission+0x27/0xb0
[ 308.266025] qib_ib0.8006: multicast join failed for
ff12:401b:8006:0000:0000:0000:ffff:ffff, status -22
[ 308.323421] [<ffffffffbd46f5d3>] vfs_write+0xc3/0x1f0
[ 308.347077] [<ffffffffbd492a5c>] ? fget_light+0xfc/0x510
[ 308.372533] [<ffffffffbd47045a>] SyS_write+0x8a/0x100
[ 308.396456] [<ffffffffbd9ff355>] system_call_fastpath+0x1c/0x21
The code calls a qib_map_page() which has never correctly tested for a
mapping error.
Fix by testing for pci_dma_mapping_error() in all cases and properly
handling the failure in the caller.
Additionally, streamline qib_map_page() arguments to satisfy just
the single caller.
Cc: <stable@vger.kernel.org>
Reviewed-by: Alex Estrin <alex.estrin@intel.com>
Tested-by: Don Dutile <ddutile@redhat.com>
Reviewed-by: Don Dutile <ddutile@redhat.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b15606f47b89b0b09936d7f45b59ba6275527041 ]
Return code wasn't set properly when CNQ allocation failed.
This only affect error message logging, currently user will
receive an error message that says the qedr driver load failed
with rc '0', instead of ENOMEM
Fixes: ec72fce4 ("qedr: Add support for RoCE HW init")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c3594f22302cca5e924e47ec1cc8edd265708f41 ]
QPs that were configured with ack timeout value lower than 1
msec will not implement re-transmission timeout.
This means that if a packet / ACK were dropped, the QP
will not retransmit this packet.
This can lead to an application hang.
Fixes: cecbcddf6 ("qedr: Add support for QP verbs")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5d414b178e950ce9685c253994cc730893d5d887 ]
"err" is either zero or possibly uninitialized here. It should be
-EINVAL.
Fixes: 427c1e7bcd7e ("{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a18177925c252da7801149abe217c05b80884798 ]
The commit cited below added a gid_type field (RoCEv1 or RoCEv2)
to GID properties.
When adding GIDs, this gid_type field was copied over to the
hardware gid table. However, when deleting GIDs, the gid_type field
was not copied over to the hardware gid table.
As a result, when running RoCEv2, all RoCEv2 gids in the
hardware gid table were set to type RoCEv1 when any gid was deleted.
This problem would persist until the next gid was added (which would again
restore the gid_type field for all the gids in the hardware gid table).
Fix this by copying over the gid_type field to the hardware gid table
when deleting gids, so that the gid_type of all remaining gids is
preserved when a gid is deleted.
Fixes: b699a859d17b ("IB/mlx4: Add gid_type to GID properties")
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0077416a3d529baccbe07ab3242e8db541cfadf6 ]
When using IPv4 addresses in RoCEv2, the GID format for the mapped
IPv4 address should be: ::ffff:<4-byte IPv4 address>.
In the cited commit, IPv4 mapped IPV6 addresses had the 3 upper dwords
zeroed out by memset, which resulted in deleting the ffff field.
However, since procedure ipv6_addr_v4mapped() already verifies that the
gid has format ::ffff:<ipv4 address>, no change is needed for the gid,
and the memset can simply be removed.
Fixes: 7e57b85c444c ("IB/mlx4: Add support for setting RoCEv2 gids in hardware")
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 551e1c67b4207455375a2e7a285dea1c7e8fc361 ]
iWARP does not support RDMA WRITE or SEND with immediate data.
Driver should check this before submitting to FW and return an
immediate error
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e3fd112cbf21d049faf64ba1471d72b93c22109a ]
Race in qedr_poll_cq, lastest_cqe wasn't protected by lock,
leading to a case where two context's accessing poll_cq at
the same time lead to one of them having a pointer to an old
latest_cqe and reading an invalid cqe element
Signed-off-by: Amit Radzi <Amit.Radzi@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b081808a66345ba725b77ecd8d759bee874cd937 ]
Failure in XRCD FW deallocation command leaves memory leaked and
returns error to the user which he can't do anything about it.
This patch changes behavior to always free memory and always return
success to the user.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6376e926af1a8661dd1b2e6d0896e07f84a35844 ]
If the application invalidates the MR before the FMR WR, HW parses the
consumer key portion of the stag and returns an invalid stag key
Asynchronous Event (AE) that tears down the QP.
Fix this by zeroing-out the consumer key portion of the allocated stag
returned to application for FMR.
Fixes: ee855d3b93f3 ("RDMA/i40iw: Add base memory management extensions")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f9e76ca3771bf23d2142a81a88ddd8f31f5c4c03 upstream.
A pio send egress error can occur when the PSM library attempts to
to send a bad packet. That issue is still being investigated.
The pio error interrupt handler then attempts to progress the recovery
of the errored pio send context.
Code inspection reveals that the handling lacks the necessary locking
if that recovery interleaves with a PSM close of the "context" object
contains the pio send context.
The lack of the locking can cause the recovery to access the already
freed pio send context object and incorrectly deduce that the pio
send context is actually a kernel pio send context as shown by the
NULL deref stack below:
[<ffffffff8143d78c>] _dev_info+0x6c/0x90
[<ffffffffc0613230>] sc_restart+0x70/0x1f0 [hfi1]
[<ffffffff816ab124>] ? __schedule+0x424/0x9b0
[<ffffffffc06133c5>] sc_halted+0x15/0x20 [hfi1]
[<ffffffff810aa3ba>] process_one_work+0x17a/0x440
[<ffffffff810ab086>] worker_thread+0x126/0x3c0
[<ffffffff810aaf60>] ? manage_workers.isra.24+0x2a0/0x2a0
[<ffffffff810b252f>] kthread+0xcf/0xe0
[<ffffffff810b2460>] ? insert_kthread_work+0x40/0x40
[<ffffffff816b8798>] ret_from_fork+0x58/0x90
[<ffffffff810b2460>] ? insert_kthread_work+0x40/0x40
This is the best case scenario and other scenarios can corrupt the
already freed memory.
Fix by adding the necessary locking in the pio send context error
handler.
Cc: <stable@vger.kernel.org> # 4.9.x
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45d924571a5e1329580811f2419da61b07ac3613 upstream.
When an invalid num_vls is used as a module parameter, the code
execution follows an exception path where the macro dd_dev_err()
expects dd->pcidev->dev not to be NULL in hfi1_init_dd(). This
causes a NULL pointer dereference.
Fix hfi1_init_dd() by initializing dd->pcidev and dd->pcidev->dev
earlier in the code. If a dd exists, then dd->pcidev and
dd->pcidev->dev always exists.
BUG: unable to handle kernel NULL pointer dereference
at 00000000000000f0
IP: __dev_printk+0x15/0x90
Workqueue: events work_for_cpu_fn
RIP: 0010:__dev_printk+0x15/0x90
Call Trace:
dev_err+0x6c/0x90
? hfi1_init_pportdata+0x38d/0x3f0 [hfi1]
hfi1_init_dd+0xdd/0x2530 [hfi1]
? pci_conf1_read+0xb2/0xf0
? pci_read_config_word.part.9+0x64/0x80
? pci_conf1_write+0xb0/0xf0
? pcie_capability_clear_and_set_word+0x57/0x80
init_one+0x141/0x490 [hfi1]
local_pci_probe+0x3f/0xa0
work_for_cpu_fn+0x10/0x20
process_one_work+0x152/0x350
worker_thread+0x1cf/0x3e0
kthread+0xf5/0x130
? max_active_store+0x80/0x80
? kthread_bind+0x10/0x10
? do_syscall_64+0x6e/0x1a0
? SyS_exit_group+0x10/0x10
ret_from_fork+0x35/0x40
Cc: <stable@vger.kernel.org> # 4.9.x
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f32ac2e452c2180cd2df581cbadac183e27ecd0 upstream.
Before the change, if the user passed a static rate value different
than zero and the FW doesn't support static rate,
it would end up configuring rate of 2.5 GBps.
Fix this by using rate 0; unlimited, in cases where FW
doesn't support static rate configuration.
Cc: <stable@vger.kernel.org> # 3.10
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 002bf2282b2d7318e444dca9ffcb994afc5d5f15 upstream.
Ensure that user didn't supply values too large that can cause overflow.
UBSAN: Undefined behaviour in drivers/infiniband/hw/mlx5/qp.c:263:23
shift exponent -2147483648 is negative
CPU: 0 PID: 292 Comm: syzkaller612609 Not tainted 4.16.0-rc1+ #131
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014 Call
Trace:
dump_stack+0xde/0x164
ubsan_epilogue+0xe/0x81
set_rq_size+0x7c2/0xa90
create_qp_common+0xc18/0x43c0
mlx5_ib_create_qp+0x379/0x1ca0
create_qp.isra.5+0xc94/0x2260
ib_uverbs_create_qp+0x21b/0x2a0
ib_uverbs_write+0xc2c/0x1010
vfs_write+0x1b0/0x550
SyS_write+0xc7/0x1a0
do_syscall_64+0x1aa/0x740
entry_SYSCALL_64_after_hwframe+0x26/0x9b
RIP: 0033:0x433569
RSP: 002b:00007ffc6e62f448 EFLAGS: 00000217 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00000000004002f8 RCX: 0000000000433569
RDX: 0000000000000070 RSI: 00000000200042c0 RDI: 0000000000000003
RBP: 00000000006d5018 R08: 00000000004002f8 R09: 00000000004002f8
R10: 00000000004002f8 R11: 0000000000000217 R12: 0000000000000000
R13: 000000000040c9f0 R14: 000000000040ca80 R15: 0000000000000006
Cc: <stable@vger.kernel.org> # 3.10
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Cc: syzkaller <syzkaller@googlegroups.com>
Reported-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26bff1bd74a4f7417509a83295614e9dab995b2a upstream.
The c4iw_rdev_close() logic was not releasing all the hw
resources (PBL and RQT memory) during the device removal
event (driver unload / system reboot). This can cause panic
in gen_pool_destroy().
The module remove function will wait for all the hw
resources to be released during the device removal event.
Fixes c12a67fe(iw_cxgb4: free EQ queue memory on last deref)
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Cc: stable@vger.kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 75a4598209cbe45540baa316c3b51d9db222e96e upstream.
mlx5 modify_qp() relies on FW that the error will be thrown if wrong
state is supplied. The missing check in FW causes the following crash
while using XRC_TGT QPs.
[ 14.769632] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 14.771085] IP: mlx5_ib_modify_qp+0xf60/0x13f0
[ 14.771894] PGD 800000001472e067 P4D 800000001472e067 PUD 14529067 PMD 0
[ 14.773126] Oops: 0002 [#1] SMP PTI
[ 14.773763] CPU: 0 PID: 365 Comm: ubsan Not tainted 4.16.0-rc1-00038-g8151138c0793 #119
[ 14.775192] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
[ 14.777522] RIP: 0010:mlx5_ib_modify_qp+0xf60/0x13f0
[ 14.778417] RSP: 0018:ffffbf48001c7bd8 EFLAGS: 00010246
[ 14.779346] RAX: 0000000000000000 RBX: ffff9a8f9447d400 RCX: 0000000000000000
[ 14.780643] RDX: 0000000000000000 RSI: 000000000000000a RDI: 0000000000000000
[ 14.781930] RBP: 0000000000000000 R08: 00000000000217b0 R09: ffffffffbc9c1504
[ 14.783214] R10: fffff4a180519480 R11: ffff9a8f94523600 R12: ffff9a8f9493e240
[ 14.784507] R13: ffff9a8f9447d738 R14: 000000000000050a R15: 0000000000000000
[ 14.785800] FS: 00007f545b466700(0000) GS:ffff9a8f9fc00000(0000) knlGS:0000000000000000
[ 14.787073] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 14.787792] CR2: 0000000000000000 CR3: 00000000144be000 CR4: 00000000000006b0
[ 14.788689] Call Trace:
[ 14.789007] _ib_modify_qp+0x71/0x120
[ 14.789475] modify_qp.isra.20+0x207/0x2f0
[ 14.790010] ib_uverbs_modify_qp+0x90/0xe0
[ 14.790532] ib_uverbs_write+0x1d2/0x3c0
[ 14.791049] ? __handle_mm_fault+0x93c/0xe40
[ 14.791644] __vfs_write+0x36/0x180
[ 14.792096] ? handle_mm_fault+0xc1/0x210
[ 14.792601] vfs_write+0xad/0x1e0
[ 14.793018] SyS_write+0x52/0xc0
[ 14.793422] do_syscall_64+0x75/0x180
[ 14.793888] entry_SYSCALL_64_after_hwframe+0x21/0x86
[ 14.794527] RIP: 0033:0x7f545ad76099
[ 14.794975] RSP: 002b:00007ffd78787468 EFLAGS: 00000287 ORIG_RAX: 0000000000000001
[ 14.795958] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f545ad76099
[ 14.797075] RDX: 0000000000000078 RSI: 0000000020009000 RDI: 0000000000000003
[ 14.798140] RBP: 00007ffd78787470 R08: 00007ffd78787480 R09: 00007ffd78787480
[ 14.799207] R10: 00007ffd78787480 R11: 0000000000000287 R12: 00005599ada98760
[ 14.800277] R13: 00007ffd78787560 R14: 0000000000000000 R15: 0000000000000000
[ 14.801341] Code: 4c 8b 1c 24 48 8b 83 70 02 00 00 48 c7 83 cc 02 00
00 00 00 00 00 48 c7 83 24 03 00 00 00 00 00 00 c7 83 2c 03 00 00 00 00
00 00 <c7> 00 00 00 00 00 48 8b 83 70 02 00 00 c7 40 04 00 00 00 00 4c
[ 14.804012] RIP: mlx5_ib_modify_qp+0xf60/0x13f0 RSP: ffffbf48001c7bd8
[ 14.804838] CR2: 0000000000000000
[ 14.805288] ---[ end trace 3f1da0df5c8b7c37 ]---
Cc: syzkaller <syzkaller@googlegroups.com>
Reported-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c4dd4b69f55abcc8dd079f8de55d9d8c2ddbefce ]
This fixes a kernel panic when loading the hfi driver as a dynamic module.
Signed-off-by: Steven L Roberts <robers97@gmail.com>
Reviewed-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1dad0ebeea1cd890b8892523f736916e245b0aef ]
The patch 761e19a504af (RDMA/iw_cxgb4: Handle return value of
c4iw_ofld_send() in abort_arp_failure()) from May 6, 2016
leads to the following static checker warning:
drivers/infiniband/hw/cxgb4/cm.c:575 abort_arp_failure()
warn: passing freed memory 'skb'
Also fixes skb leak when l2t resolution fails
Fixes: 761e19a504afa55 (RDMA/iw_cxgb4: Handle return value of
c4iw_ofld_send() in abort_arp_failure())
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fe99afd1febd74e0ef1fed7e3283f09effe1f4f0 ]
Lower Inbound RDMA Read Queue (Q1) object count by a factor of 2
as it is incorrectly doubled. Also, round up Q1 and Transmit FIFO (XF)
object count to power of 2 to satisfy hardware requirement.
Fixes: 86dbcd0f12e9 ("i40iw: add file to handle cqp calls")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit df8b13a1b23356d01dfc4647a5629cdb0f4ce566 ]
Partial FPDU processing is broken as the sequence number
for the first partial FPDU is wrong due to incorrect
Q2 buffer offset. The offset should be 64 rather than 16.
Fixes: 786c6adb3a94 ("i40iw: add puda code")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c292dbb398ee46fc1343daf6c3cf9715a75688e upstream.
Add a check for the length of the qpin structure to prevent out-of-bounds reads
BUG: KASAN: slab-out-of-bounds in create_raw_packet_qp+0x114c/0x15e2
Read of size 8192 at addr ffff880066b99290 by task syz-executor3/549
CPU: 3 PID: 549 Comm: syz-executor3 Not tainted 4.15.0-rc2+ #27 Hardware
name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
Call Trace:
dump_stack+0x8d/0xd4
print_address_description+0x73/0x290
kasan_report+0x25c/0x370
? create_raw_packet_qp+0x114c/0x15e2
memcpy+0x1f/0x50
create_raw_packet_qp+0x114c/0x15e2
? create_raw_packet_qp_tis.isra.28+0x13d/0x13d
? lock_acquire+0x370/0x370
create_qp_common+0x2245/0x3b50
? destroy_qp_user.isra.47+0x100/0x100
? kasan_kmalloc+0x13d/0x170
? sched_clock_cpu+0x18/0x180
? fs_reclaim_acquire.part.15+0x5/0x30
? __lock_acquire+0xa11/0x1da0
? sched_clock_cpu+0x18/0x180
? kmem_cache_alloc_trace+0x17e/0x310
? mlx5_ib_create_qp+0x30e/0x17b0
mlx5_ib_create_qp+0x33d/0x17b0
? sched_clock_cpu+0x18/0x180
? create_qp_common+0x3b50/0x3b50
? lock_acquire+0x370/0x370
? __radix_tree_lookup+0x180/0x220
? uverbs_try_lock_object+0x68/0xc0
? rdma_lookup_get_uobject+0x114/0x240
create_qp.isra.5+0xce4/0x1e20
? ib_uverbs_ex_create_cq_cb+0xa0/0xa0
? copy_ah_attr_from_uverbs.isra.2+0xa00/0xa00
? ib_uverbs_cq_event_handler+0x160/0x160
? __might_fault+0x17c/0x1c0
ib_uverbs_create_qp+0x21b/0x2a0
? ib_uverbs_destroy_cq+0x2e0/0x2e0
ib_uverbs_write+0x55a/0xad0
? ib_uverbs_destroy_cq+0x2e0/0x2e0
? ib_uverbs_destroy_cq+0x2e0/0x2e0
? ib_uverbs_open+0x760/0x760
? futex_wake+0x147/0x410
? check_prev_add+0x1680/0x1680
? do_futex+0x3d3/0xa60
? sched_clock_cpu+0x18/0x180
__vfs_write+0xf7/0x5c0
? ib_uverbs_open+0x760/0x760
? kernel_read+0x110/0x110
? lock_acquire+0x370/0x370
? __fget+0x264/0x3b0
vfs_write+0x18a/0x460
SyS_write+0xc7/0x1a0
? SyS_read+0x1a0/0x1a0
? trace_hardirqs_on_thunk+0x1a/0x1c
entry_SYSCALL_64_fastpath+0x18/0x85
RIP: 0033:0x4477b9
RSP: 002b:00007f1822cadc18 EFLAGS: 00000292 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00000000004477b9
RDX: 0000000000000070 RSI: 000000002000a000 RDI: 0000000000000005
RBP: 0000000000708000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000292 R12: 00000000ffffffff
R13: 0000000000005d70 R14: 00000000006e6e30 R15: 0000000020010ff0
Allocated by task 549:
__kmalloc+0x15e/0x340
kvmalloc_node+0xa1/0xd0
create_user_qp.isra.46+0xd42/0x1610
create_qp_common+0x2e63/0x3b50
mlx5_ib_create_qp+0x33d/0x17b0
create_qp.isra.5+0xce4/0x1e20
ib_uverbs_create_qp+0x21b/0x2a0
ib_uverbs_write+0x55a/0xad0
__vfs_write+0xf7/0x5c0
vfs_write+0x18a/0x460
SyS_write+0xc7/0x1a0
entry_SYSCALL_64_fastpath+0x18/0x85
Freed by task 368:
kfree+0xeb/0x2f0
kernfs_fop_release+0x140/0x180
__fput+0x266/0x700
task_work_run+0x104/0x180
exit_to_usermode_loop+0xf7/0x110
syscall_return_slowpath+0x298/0x370
entry_SYSCALL_64_fastpath+0x83/0x85
The buggy address belongs to the object at ffff880066b99180 which
belongs to the cache kmalloc-512 of size 512 The buggy address is
located 272 bytes inside of 512-byte region [ffff880066b99180,
ffff880066b99380) The buggy address belongs to the page:
page:000000006040eedd count:1 mapcount:0 mapping: (null)
index:0x0 compound_mapcount: 0
flags: 0x4000000000008100(slab|head)
raw: 4000000000008100 0000000000000000 0000000000000000 0000000180190019
raw: ffffea00019a7500 0000000b0000000b ffff88006c403080 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff880066b99180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff880066b99200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff880066b99280: 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff880066b99300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff880066b99380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Cc: syzkaller <syzkaller@googlegroups.com>
Fixes: 0fb2ed66a14c ("IB/mlx5: Add create and destroy functionality for Raw Packet QP")
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c2b37f76485f073f020e60b5954b6dc4e55f693c upstream.
This patch validates user provided input to prevent integer overflow due
to integer manipulation in the mlx5_ib_create_srq function.
Cc: syzkaller <syzkaller@googlegroups.com>
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 744820869166c8c78be891240cf5f66e8a333694 ]
Debugfs file reset_stats is created with S_IRUSR permissions,
but ocrdma_dbgfs_ops_read() doesn't support OCRDMA_RESET_STATS,
whereas ocrdma_dbgfs_ops_write() supports only OCRDMA_RESET_STATS.
The patch fixes misstype with permissions.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 22546b741af8355cd2e16739b6af4a8f17081839 ]
Soft lockups can occur because the mad processing on different CPUs acquire
the spin lock dc8051_lock:
[534552.835870] [<ffffffffa026f993>] ? read_dev_port_cntr.isra.37+0x23/0x160 [hfi1]
[534552.835880] [<ffffffffa02775af>] read_dev_cntr+0x4f/0x60 [hfi1]
[534552.835893] [<ffffffffa028d7cd>] pma_get_opa_portstatus+0x64d/0x8c0 [hfi1]
[534552.835904] [<ffffffffa0290e7d>] hfi1_process_mad+0x48d/0x18c0 [hfi1]
[534552.835908] [<ffffffff811dc1f1>] ? __slab_free+0x81/0x2f0
[534552.835936] [<ffffffffa024c34e>] ? ib_mad_recv_done+0x21e/0xa30 [ib_core]
[534552.835939] [<ffffffff811dd153>] ? __kmalloc+0x1f3/0x240
[534552.835947] [<ffffffffa024c3fb>] ib_mad_recv_done+0x2cb/0xa30 [ib_core]
[534552.835955] [<ffffffffa0237c85>] __ib_process_cq+0x55/0xd0 [ib_core]
[534552.835962] [<ffffffffa0237d70>] ib_cq_poll_work+0x20/0x60 [ib_core]
[534552.835964] [<ffffffff810a7f3b>] process_one_work+0x17b/0x470
[534552.835966] [<ffffffff810a8d76>] worker_thread+0x126/0x410
[534552.835969] [<ffffffff810a8c50>] ? rescuer_thread+0x460/0x460
[534552.835971] [<ffffffff810b052f>] kthread+0xcf/0xe0
[534552.835974] [<ffffffff810b0460>] ? kthread_create_on_node+0x140/0x140
[534552.835977] [<ffffffff81696418>] ret_from_fork+0x58/0x90
[534552.835980] [<ffffffff810b0460>] ? kthread_create_on_node+0x140/0x140
This issue is made worse when the 8051 is busy and the reads take longer.
Fix by using a non-spinning lock procure.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: Mike Marciszyn <mike.marciniszyn@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 12f8fedef2ec94c783f929126b20440a01512c14 ]
There is a difference when parsing a completion entry between Ethernet
and IB ports. When link layer is Ethernet the bits describe the type of
L3 header in the packet. In the case when link layer is Ethernet and VLAN
header is present the value of SL is equal to the 3 UP bits in the VLAN
header. If VLAN header is not present then the SL is undefined and consumer
of the completion should check if IB_WC_WITH_VLAN is set.
While that, this patch also fills the vlan_id field in the completion if
present.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1377661298d2820d675553d186c31b6f46c140d0 ]
Anonymous VMA (->vm_ops == NULL) cannot be shared, otherwise
it would lead to SIGBUS.
Remove the shared flags from the vma after we change it to be
anonymous.
This is easily reproduced by doing modprobe -r while running a
user-space application such as raw_ethernet_bw.
Fixes: 7c2344c3bbf97 ('IB/mlx5: Implements disassociate_ucontext API')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ecc7d83be3243835c9396a1a2fb8ce95f205207b ]
When the driver disassociate user context, it changes the vma to
anonymous by setting the vm_ops to null and zap the vma ptes.
In order to avoid race in the kernel, we need to take write lock
before we change the vma entries.
Fixes: 7c2344c3bbf97 ('IB/mlx5: Implements disassociate_ucontext API')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ca37a664a8e4e9988b220988ceb4d79e3316f195 ]
Anonymous VMA (->vm_ops == NULL) cannot be shared, otherwise
it would lead to SIGBUS.
Remove the shared flags from the vma after we change it to be
anonymous.
This is easily reproduced by doing modprobe -r while running a
user-space application such as raw_ethernet_bw.
Fixes: ae184ddeca5db ('IB/mlx4_ib: Disassociate support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 22c3653d04bd0c67b75e99d85e0c0bdf83947df5 ]
When the driver disassociate user context, it changes the vma to
anonymous by setting the vm_ops to null and zap the vma ptes.
In order to avoid race in the kernel, we need to take write lock
before we change the vma entries.
Fixes: ae184ddeca5db ('IB/mlx4_ib: Disassociate support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fb897ad315643e5dc1092a115b3cec914b66df9d ]
Attempting to read the status of a QSFP cable creates noise in the logs
and misses out on setting an appropriate Offline/Disabled Reason if the
cable is not plugged in. Check for this prior to attempting the read and
attendant retries.
Fixes: 673b975f1fba ("IB/hfi1: Add QSFP sanity pre-check")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
