| Age | Commit message (Collapse) | Author |
|---|
|
The capabilities include:
- Max number of compressed and aggregated CQEs in a single session,
while zero means unsupported.
- For Responder, there are two formats of mini CQE: mini CQE with Rx
hash and mini CQE with checksum. They're mutual exclusive.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The capabilities whether hardware support multi packet WQE or not is
exposed to user space through query_device by uhw.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rmda fixes from Doug Ledford.
"First round of -rc fixes.
Due to various issues, I've been away and couldn't send a pull request
for about three weeks. There were a number of -rc patches that built
up in the meantime (some where there already from the early -rc
stages). Obviously, there were way too many to send now, so I tried to
pare the list down to the more important patches for the -rc cycle.
Most of the code has had plenty of soak time at the various vendor's
testing setups, so I doubt there will be another -rc pull request this
cycle. I also tried to limit the patches to those with smaller
footprints, so even though a shortlog is longer than I would like, the
actual diffstat is mostly very small with the exception of just three
files that had more changes, and a couple files with pure removals.
Summary:
- Misc Intel hfi1 fixes
- Misc Mellanox mlx4, mlx5, and rxe fixes
- A couple cxgb4 fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (34 commits)
iw_cxgb4: invalidate the mr when posting a read_w_inv wr
iw_cxgb4: set *bad_wr for post_send/post_recv errors
IB/rxe: Update qp state for user query
IB/rxe: Clear queue buffer when modifying QP to reset
IB/rxe: Fix handling of erroneous WR
IB/rxe: Fix kernel panic in UDP tunnel with GRO and RX checksum
IB/mlx4: Fix create CQ error flow
IB/mlx4: Check gid_index return value
IB/mlx5: Fix NULL pointer dereference on debug print
IB/mlx5: Fix fatal error dispatching
IB/mlx5: Resolve soft lock on massive reg MRs
IB/mlx5: Use cache line size to select CQE stride
IB/mlx5: Validate requested RQT size
IB/mlx5: Fix memory leak in query device
IB/core: Avoid unsigned int overflow in sg_alloc_table
IB/core: Add missing check for addr_resolve callback return value
IB/core: Set routable RoCE gid type for ipv4/ipv6 networks
IB/cm: Mark stale CM id's whenever the mad agent was unregistered
IB/uverbs: Fix leak of XRC target QPs
IB/hfi1: Remove incorrect IS_ERR check
...
|
|
Add the 512 bytes limit of RDMA READ and the size of remote
address to the max SGE calculation.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
We put INT_MAX since this is the max value that can be held.
Though there is no hardware limitation, this is practically
a large enough number so we can use it.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When an internal error condition is detected, make sure to set the
device inactive after dispatching the event so ULPs can get a
notification of this event.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
We need to free dev->port when we fail to enable RoCE or
initialize node data.
Fixes: 0837e86a7a34 ('IB/mlx5: Add per port counters')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In order to support steering rules which add encapsulation headers,
encap_id parameter is needed.
Add new mlx5_flow_act struct which holds action related parameter:
action, flow_tag and encap_id. Use mlx5_flow_act struct when adding a new
steering rule.
This patch doesn't change any functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating flow tables, allow the caller to specify creation flags.
Currently no flags are used and as such this patch doesn't add any new
functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma
Saeed Mahameed says:
====================
Mellanox mlx5 core driver updates 2016-10-25
This series contains some updates and fixes of mlx5 core and
IB drivers with the addition of two features that demand
new low level commands and infrastructure updates.
- SRIOV VF max rate limit support
- mlx5e tc support for FWD rules with counter.
Needed for both net and rdma subsystems.
Updates and Fixes:
From Saeed Mahameed (2):
- mlx5 IB: Skip handling unknown mlx5 events
- Add ConnectX-5 PCIe 4.0 VF device ID
From Artemy Kovalyov (2):
- Update struct mlx5_ifc_xrqc_bits
- Ensure SRQ physical address structure endianness
From Eugenia Emantayev (1):
- Fix length of async_event_mask
New Features:
From Mohamad Haj Yahia (3): mlx5 SRIOV VF max rate limit support
- Introduce TSAR manipulation firmware commands
- Introduce E-switch QoS management
- Add SRIOV VF max rate configuration support
From Mark Bloch (7): mlx5e Tc support for FWD rule with counter
- Don't unlock fte while still using it
- Use fte status to decide on firmware command
- Refactor find_flow_rule
- Group similar rules under the same fte
- Add multi dest support
- Add option to add fwd rule with counter
- mlx5e tc support for FWD rule with counter
Mark here fixed two trivial issues with the flow steering core, and did
some refactoring in the flow steering API to support adding mulit destination
rules to the same hardware flow table entry at once. In the last two patches
added the ability to populate a flow rule with a flow counter to the same flow entry.
V2: Dropped some patches that added new structures without adding any usage of them.
Added SRIOV VF max rate configuration support patch that introduces
the usage of the TSAR infrastructure.
Added flow steering fixes and refactoring in addition to mlx5 tc
support for forward rule with counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when calling mlx5_add_flow_rule we accept
only one flow destination, this commit allows to pass
multiple destinations.
This change forces us to change the return structure to a more
flexible one. We introduce a flow handle (struct mlx5_flow_handle),
it holds internally the number for rules created and holds an array
where each cell points the to a flow rule.
From the consumers (of mlx5_add_flow_rule) point of view this
change is only cosmetic and requires only to change the type
of the returned value they store.
From the core point of view, we now need to use a loop when
allocating and deleting rules (e.g given to us a flow handler).
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Do not dispatch unknown mlx5 core events on mlx5_ib_event.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
ARM 64B cache line systems have L1_CACHE_BYTES set to 128.
cache_line_size() will return the correct size.
Fixes: cf50b5efa2fe('net/mlx5_core/ib: New device capabilities
handling.')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull main rdma updates from Doug Ledford:
"This is the main pull request for the rdma stack this release. The
code has been through 0day and I had it tagged for linux-next testing
for a couple days.
Summary:
- updates to mlx5
- updates to mlx4 (two conflicts, both minor and easily resolved)
- updates to iw_cxgb4 (one conflict, not so obvious to resolve,
proper resolution is to keep the code in cxgb4_main.c as it is in
Linus' tree as attach_uld was refactored and moved into
cxgb4_uld.c)
- improvements to uAPI (moved vendor specific API elements to uAPI
area)
- add hns-roce driver and hns and hns-roce ACPI reset support
- conversion of all rdma code away from deprecated
create_singlethread_workqueue
- security improvement: remove unsafe ib_get_dma_mr (breaks lustre in
staging)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (75 commits)
staging/lustre: Disable InfiniBand support
iw_cxgb4: add fast-path for small REG_MR operations
cxgb4: advertise support for FR_NSMR_TPTE_WR
IB/core: correctly handle rdma_rw_init_mrs() failure
IB/srp: Fix infinite loop when FMR sg[0].offset != 0
IB/srp: Remove an unused argument
IB/core: Improve ib_map_mr_sg() documentation
IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets
IB/mthca: Move user vendor structures
IB/nes: Move user vendor structures
IB/ocrdma: Move user vendor structures
IB/mlx4: Move user vendor structures
IB/cxgb4: Move user vendor structures
IB/cxgb3: Move user vendor structures
IB/mlx5: Move and decouple user vendor structures
IB/{core,hw}: Add constant for node_desc
ipoib: Make ipoib_warn ratelimited
IB/mlx4/alias_GUID: Remove deprecated create_singlethread_workqueue
IB/ipoib_verbs: Remove deprecated create_singlethread_workqueue
IB/ipoib: Remove deprecated create_singlethread_workqueue
...
|
|
This patch decouples and moves vendors specific structures to
common UAPI folder which will be visible to all consumers.
These structures are used by user-space library driver
(libmlx5) and currently manually copied to that library.
This move will allow cross-compile against these files and
simplify introduction of vendor specific data.
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
IB bond device name is now 'mlx5_bond_X', instead of
'mlx5_X'.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When LAG is active, port up/down events should be triggered
by tracking the LAG master, and not one of the two slave
netdevs.
In the same manner, ib_query_port() should return the details
of the LAG master.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This is done in two steps:
1) Issuing CREATE_VPORT_LAG in order to have Ethernet traffic from
both ports arriving on PF0 root flowtable, so we will be able to catch
all raw-eth traffic on PF0.
2) Creation of LAG demux flowtable in order to direct all non-raw-eth
traffic back to its source port, assuring that normal Ethernet
traffic "jumps" to the root flowtable of its RX port (non-LAG behavior).
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Since ib_query_port() in RoCE returns the state of its netdev as the port
state, it makes sense to propagate the port up/down events to ib_core
when the netdev port state changes, instead of relying on traditional
core events.
This also keeps both the event and ib_query_port() synchronized.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add support to receive Traffic Class, specific IPv6 protocol
or IPv6 flow label.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add support to receive TOS or specific IPv4 protocol.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add validation check that all set fields in flow specification
are supported by vendor.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add support to create sniffer rule. This rule receive all
incoming and outgoing packets from the port.
A user could create such rule by using IB_FLOW_ATTR_SNIFFER type.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Move the reference count increasing of flow table to be in
create_flow_rule, it will increase the reference count for each rule
creation and not for each flow.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Fix covertiy warning of passing "&flow_attr" to function
"create_flow_rule" which uses it as an array.
In addition pass flow attributes argument as const.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Saving the flow table priority object's pointer in the flow handle
is necessary for downstream patches since the sniffer flow table isn't
placed at the standard flow_db structure but in a different database.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Fix multicast flow rule leak on adding unicast rule failure.
Fixes: 038d2ef87572 ('IB/mlx5: Add flow steering support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Expose RSS related capabilities on both IB and vendor channels.
In addition to the IB capabilities the driver reports some extra
capabilities on its vendor channel:
- Bit mask of the supported types of hash functions.
- Bit mask of the supported RX fields that can participate
in the RX hashing.
Those capabilities are applicable only when the link layer
is Ethernet.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Instead of exposing ib_get_dma_mr to ULPs and letting them use it more or
less unchecked, this moves the capability of creating a global rkey into
the RDMA core, where it can be easily audited. It also prints a warning
everytime this feature is used as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
|
|
Set the source mac address in the FTE when L2 specification
is provided.
Fixes: 038d2ef87572 ('IB/mlx5: Add flow steering support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
MAD_IFC command is supported only for physical functions (PF)
and when physical port is IB. The proposed fix enforces it.
Fixes: d603c809ef91 ("IB/mlx5: Fix decision on using MAD_IFC")
Reported-by: David Chang <dchang@suse.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use TIR number based on selector, it should be done to differentiate
between RSS QP to RAW one.
Reported-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Tested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
All three conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This file does not use any structs or functions defined by io-mapping.h
(nor does it directly use iomap, ioremap, iounamp or friends). Remove it
to simplify verification of changes to io-mapping.h
The include existed since its inception in
commit e126ba97dba9edeb6fafa3665b5f8497fc9cdf8c
Author: Eli Cohen <eli@mellanox.com>
Date: Sun Jul 7 17:25:49 2013 +0300
mlx5: Add driver for Mellanox Connect-IB adapters
which looks like a copy across from the Mellanox ethernet driver.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Eli Cohen <eli@mellanox.com>
Cc: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Matan Barak <matanb@mellanox.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Replaced mlx5_query_port_proto_oper with separate functions per link
type. The functions should take different arguments so no point in
trying to unite them.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Now as all commands use mlx5 ifc interface, instead of doing two calls
for executing a command we embed command status checking into
mlx5_cmd_exec to simplify the interface.
Also we do here some cleanup for redundant software structures
(inbox/outbox) and functions and improved command failure output.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull base rdma updates from Doug Ledford:
"Round one of 4.8 code: while this is mostly normal, there is a new
driver in here (the driver was hosted outside the kernel for several
years and is actually a fairly mature and well coded driver). It
amounts to 13,000 of the 16,000 lines of added code in here.
Summary:
- Updates/fixes for iw_cxgb4 driver
- Updates/fixes for mlx5 driver
- Add flow steering and RSS API
- Add hardware stats to mlx4 and mlx5 drivers
- Add firmware version API for RDMA driver use
- Add the rxe driver (this is a software RoCE driver that makes any
Ethernet device a RoCE device)
- Fixes for i40iw driver
- Support for send only multicast joins in the cma layer
- Other minor fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (72 commits)
Soft RoCE driver
IB/core: Support for CMA multicast join flags
IB/sa: Add cached attribute containing SM information to SA port
IB/uverbs: Fix race between uverbs_close and remove_one
IB/mthca: Clean up error unwind flow in mthca_reset()
IB/mthca: NULL arg to pci_dev_put is OK
IB/hfi1: NULL arg to sc_return_credits is OK
IB/mlx4: Add diagnostic hardware counters
net/mlx4: Query performance and diagnostics counters
net/mlx4: Add diagnostic counters capability bit
Use smaller 512 byte messages for portmapper messages
IB/ipoib: Report SG feature regardless of HW UD CSUM capability
IB/mlx4: Don't use GFP_ATOMIC for CQ resize struct
IB/hfi1: Disable by default
IB/rdmavt: Disable by default
IB/mlx5: Fix port counter ID association to QP offset
IB/mlx5: Fix iteration overrun in GSI qps
i40iw: Add NULL check for puda buffer
i40iw: Change dup_ack_thresh to u8
i40iw: Remove unnecessary check for moving CQ head
...
|
|
|
|
Fixes the following sparse warning:
drivers/infiniband/hw/mlx5/main.c:2574:25: warning: duplicate const
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Reduce the set of arguments passed to mlx5_add_flow_rule
by introducing flow_spec structure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
And remove sysfs entry in favor of the common code.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Expose new counters using the get protocol stats callback.
We expose the following counters:
|------------------------------------------------------------------------|
| Name | IB | EN | Description |
|------------------------------------------------------------------------|
|rx_write_requests | + | - | Number of received WRITE requests for |
| | | | the associated QP. |
|------------------------------------------------------------------------|
|rx_read_requests | + | - | Number of received READ requests for |
| | | | the associated QP. |
|------------------------------------------------------------------------|
|rx_atomic_requests | + | - | Number of received ATOMIC requests for |
| | | | the associated QP. |
|------------------------------------------------------------------------|
|out_of_buffer | + | + | Number of drops occurred due to lack |
| | | | of WQE for the associated QPs/RQs. |
|------------------------------------------------------------------------|
|out_of_sequence | + | - | Number of errors in the packet |
| | | | transport sequence number |
|------------------------------------------------------------------------|
|duplicate_request | + | + | Number of received duplicated packets. |
| | | | A request that previously executed is |
| | | | named duplicated. |
|------------------------------------------------------------------------|
|rnr_nak_retry_err | + | + | Number of received RNR NAC packets. |
| | | | The QP retry limit did not exceed. |
|------------------------------------------------------------------------|
|packet_seq_err | + | + | Number of received NAK - sequence error|
| | | | packets. The QP retry limit did not |
| | | | exceed. |
|------------------------------------------------------------------------|
|implied_nak_err | + | + | Number of times the requester detected |
| | | | an ACK with a PSN larger than expected |
| | | | PSN for RDMA READ or ATOMIC response |
| | | | The QP retry limit did not exceed. |
|------------------------------------------------------------------------|
|local_ack_timeout_err| + | - | Number of NO ACK responses from |
| | | | responder within timer interval. |
| | | | The QP retry limit did not exceed. |
|------------------------------------------------------------------------|
Counters are available if all of them are supported.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In order to support statistics for ports, we attach
each QP to a counter set which is dedicate to this port.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Enable mlx5 based hardware to report TCP segmentation offload (TSO)
capabilities from kernel to user space. A TSO enabled NIC will accept
big chunks of data with sizes greater than MTU for TCP traffic. The TSO
engine will break the data into separate packets and will insert headers
automatically.
The capabilities are exposed to user space through query_device by uhw
directly. The following capabilities are reported:
1. The maximum payload size in bytes supported for segmentation by TSO
engine.
2. Bitmap showing which QP types are supported by TSO operation. The bitmap
is built by members from 'enmu ib_qp_type'. For example, similar code
should be performed if UD QP is supported:
supported_qpts |= 1 << IB_QPT_UD;
To make user-space library aware of whether kernel supports uhw or not, a
new flag: cmds_supp_uhw will be returned back to user-space through
alloc_ucontext.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Enable flow steering for IPv6 traffic by using an IPv6 spec.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
