| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 7b86482632788acd48d7b9ee1867f5ad3a32ccbb ]
Use spi_is_bpw_supported() instead of directly accessing spi->controller
->bits_per_word_mask. bits_per_word_mask may be 0, which implies that
8-bits-per-word is supported. spi_is_bpw_supported() takes this into
account while spi_ctrl_mask == SPI_BPW_MASK(8) does not.
Fixes: 0b2a740b424e ("iio: adc: ad7949: enable use with non 14/16-bit controllers")
Closes: https://lore.kernel.org/linux-spi/c8b8a963-6cef-4c9b-bfef-dab2b7bd0b0f@sirena.org.uk/
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250611-iio-adc-ad7949-use-spi_is_bpw_supported-v1-1-c4e15bfd326e@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e8ad595064f6ebd5d2d1a5d5d7ebe0efce623091 upstream.
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Fixes: 1add69880240 ("iio: adc: Add support for STM32 ADC core")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://patch.msgid.link/20250515083101.3811350-1-nichen@iscas.ac.cn
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d8d7c1dbc46aa07a76acab7336a42ddd900be10 upstream.
The IIO core issues warnings when a scan mask is a subset of a previous
entry in the available_scan_masks array.
On a board using a MAX11601, the following warning is observed:
max1363 1-0064: available_scan_mask 7 subset of 6. Never used
This occurs because the entries in the max11607_mode_list[] array are not
ordered correctly. To fix this, reorder the entries so that no scan mask is
a subset of an earlier one.
While at it, reorder the mode_list[] arrays for other supported chips as
well, to prevent similar warnings on different variants.
Note fixes tag dropped as these were introduced over many commits a long
time back and the side effect until recently was a reduction in sampling
rate due to reading too many channels when only a few were desired.
Now we have a sanity check that reports this error but that is not
where the issue was introduced.
Cc: stable@vger.kernel.org
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/20250516173900.677821-2-festevam@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d21f2c2dd843bceefd9455f2919f6bb526797f0 upstream.
Since commit 2718f15403fb ("iio: sanity check available_scan_masks array"),
booting a board populated with a MAX11601 results in a flood of warnings:
max1363 1-0064: available_scan_mask 8 subset of 0. Never used
max1363 1-0064: available_scan_mask 9 subset of 0. Never used
max1363 1-0064: available_scan_mask 10 subset of 0. Never used
max1363 1-0064: available_scan_mask 11 subset of 0. Never used
max1363 1-0064: available_scan_mask 12 subset of 0. Never used
max1363 1-0064: available_scan_mask 13 subset of 0. Never used
...
These warnings are caused by incorrect offsets used for differential
channels in the MAX1363_4X_CHANS() and MAX1363_8X_CHANS() macros.
The max1363_mode_table[] defines the differential channel mappings as
follows:
MAX1363_MODE_DIFF_SINGLE(0, 1, 1 << 12),
MAX1363_MODE_DIFF_SINGLE(2, 3, 1 << 13),
MAX1363_MODE_DIFF_SINGLE(4, 5, 1 << 14),
MAX1363_MODE_DIFF_SINGLE(6, 7, 1 << 15),
MAX1363_MODE_DIFF_SINGLE(8, 9, 1 << 16),
MAX1363_MODE_DIFF_SINGLE(10, 11, 1 << 17),
MAX1363_MODE_DIFF_SINGLE(1, 0, 1 << 18),
MAX1363_MODE_DIFF_SINGLE(3, 2, 1 << 19),
MAX1363_MODE_DIFF_SINGLE(5, 4, 1 << 20),
MAX1363_MODE_DIFF_SINGLE(7, 6, 1 << 21),
MAX1363_MODE_DIFF_SINGLE(9, 8, 1 << 22),
MAX1363_MODE_DIFF_SINGLE(11, 10, 1 << 23),
Update the macros to follow this same pattern, ensuring that the scan masks
are valid and preventing the warnings.
Cc: stable@vger.kernel.org
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/20250516173900.677821-1-festevam@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3281ddcea6429f7bc1fdb39d407752dd1371aba9 upstream.
The AXP717 ADC channel maps is missing a sentinel entry at the end. This
causes a KASAN warning.
Add the missing sentinel entry.
Fixes: 5ba0cb92584b ("iio: adc: axp20x_adc: add support for AXP717 ADC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://patch.msgid.link/20250607135627.2086850-1-wens@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e5cdb098a3cb165d52282ffc3a6448642953ea13 ]
Fix Smatch-detected issue:
drivers/iio/adc/ad_sigma_delta.c:604 ad_sd_trigger_handler() error:
uninitialized symbol 'status_pos'.
The variable `status_pos` was only initialized in specific switch cases
(1, 2, 3, 4), which could leave it uninitialized if `reg_size` had an
unexpected value.
Fix by adding a default case to the switch block to catch unexpected
values of `reg_size`. Use `dev_err_ratelimited()` for error logging and
`goto irq_handled` instead of returning early.
Signed-off-by: Purva Yeshi <purvayeshi550@gmail.com>
Link: https://patch.msgid.link/20250410170408.8585-1-purvayeshi550@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 89944d88f8795c6c89b9514cb365998145511cd4 upstream.
Fix incorrect value mask for register write. Register values are 8-bit,
not 9. If this function was called with a value > 0xFF and an even addr,
it would cause writing to the next register.
Fixes: f2a22e1e172f ("iio: adc: ad7606: Add support for software mode for ad7616")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250428-iio-adc-ad7606_spi-fix-write-value-mask-v1-1-a2d5e85a809f@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c5dfea39a245b2dad869db24e2830aa299b1cf2 upstream.
Add dependency to Kconfig’s ti-ads1298 because compiling it as a module
failed with an undefined kfifo symbol.
Fixes: 00ef7708fa60 ("iio: adc: ti-ads1298: Add driver")
Signed-off-by: Arthur-Prince <r2.arthur.prince@gmail.com>
Co-developed-by: Mariana Valério <mariana.valerio2@hotmail.com>
Signed-off-by: Mariana Valério <mariana.valerio2@hotmail.com>
Link: https://patch.msgid.link/20250430191131.120831-1-r2.arthur.prince@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7cdfbc0113d087348b8e65dd79276d0f57b89a10 upstream.
Apply a mask to the raw value received over the SPI bus for unsigned
direct reads. As we found recently, SPI controllers may not set unused
bits to 0 when reading with bits_per_word != {8,16,32}. The ad7944 uses
bits_per_word of 14 and 18, so we need to mask the value to be sure we
returning the correct value to userspace during a direct read.
Fixes: d1efcf8871db ("iio: adc: ad7944: add driver for AD7944/AD7985/AD7986")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-adc-ad7944-max-high-bits-on-direct-read-v1-1-b173facceefe@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f62c49d8f32d6ce8871b01795498352775aa61db ]
The conversion result registers differs between devices. Make sure the
mapping is correct by using a device dependent .get_raw() callback function.
Fixes: 732ad34260d3 ("iio: adc: mcp3911: add support for the whole MCP39xx family")
Co-developed-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250428-mcp3911-fixes-v2-1-406e39330c3d@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52c43d80fa8370eb877fc63b1fc1eec67e1b1410 ]
Fix a typo,(PAC1934 -> PAC193X), into the link from an application note
related to the ACPI device definition.
Fixes: 0fb528c8255b ("iio: adc: adding support for PAC193x")
Reported-by: Matteo Martelli <matteomartelli3@gmail.com>
Closes: https://patch.msgid.link/172794015844.2520.11909797050797595912@njaxe.localdomain
Signed-off-by: Marius Cristea <marius.cristea@microchip.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250424-pac1934-doc_link-v1-1-9832445cb270@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8712e4986e7ce42a14c762c4c350f290989986a5 ]
The sinc4 filter has a factor 0.23 between Output Data Rate and f_{3dB}
and for sinc3 the factor is 0.272 according to the data sheets for
ad7124-4 (Rev. E.) and ad7124-8 (Rev. F).
Fixes: cef2760954cf ("iio: adc: ad7124: add 3db filter")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/20250317115247.3735016-6-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 503d20ed8cf7c7b40ec0bd94f53c490c1d91c31b ]
Replace use of storagebits with realbits for determining the number of
bytes needed for SPI transfers.
When adding SPI offload support, storagebits will always be 32 rather
than 16 for 16-bit 16-bit chips so we can no longer rely on storagebits
being the correct size expected by the SPI framework (it always uses
4 bytes for > 16-bit xfers and 2 bytes for > 8-bit xfers). Instead,
derive the correct size from realbits since it will always be correct
even when SPI offloading is used.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-vy: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250207-dlech-mainline-spi-engine-offload-2-v8-10-e48a489be48c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ffbc26bc91c1f1eb3dcf5d8776e74cbae21ee13a ]
On architectures where an s64 is not 64-bit aligned, this may result
insufficient alignment of the timestamp and the structure being too small.
Use aligned_s64 to force the alignment.
Fixes: a1caeebab07e ("iio: adc: ad7768-1: Fix too small buffer passed to iio_push_to_buffers_with_timestamp()") # aligned_s64 newer
Reported-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-3-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52d349884738c346961e153f195f4c7fe186fcf4 ]
On architectures where an s64 is only 32-bit aligned insufficient padding
would be left between the earlier elements and the timestamp. Use
aligned_s64 to enforce the correct placement and ensure the storage is
large enough.
Fixes: 54e018da3141 ("iio:ad7266: Mark transfer buffer as __be16") # aligned_s64 is much newer.
Reported-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-2-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5097eaae98e53f9ab9d35801c70da819b92ca907 ]
Here the lack of marking allows the overall structure to not be
sufficiently aligned resulting in misplacement of the timestamp
in iio_push_to_buffers_with_timestamp(). Use aligned_s64 to
force the alignment on all architectures.
Fixes: 7c0299e879dd ("iio: adc: Add support for DLN2 ADC")
Reported-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-4-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 839f81de397019f55161c5982d670ac19d836173 upstream.
clock_set_rate should be executed after devm_clk_get_enabled.
Fixes: 97ad10bb2901 ("iio: adc: rockchip_saradc: Make use of devm_clk_get_enabled")
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20250312062016.137821-1-xxm@rock-chips.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f083f8a21cc785ebe3a33f756a3fa3660611f8db upstream.
Fix register read/write routine as per datasheet.
When reading multiple consecutive registers, only the first one is read
properly. This is due to missing chip select deassert and assert again
between first and second 16bit transfer, as shown in the datasheet
AD7606C-16, rev 0, figure 110.
Fixes: f2a22e1e172f ("iio: adc: ad7606: Add support for software mode for ad7616")
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250418-wip-bl-ad7606-fix-reg-access-v3-1-d5eeb440c738@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8236644f5ecb180e80ad92d691c22bc509b747bb ]
The ad7768-1 ADC output code is two's complement, meaning that the voltage
conversion result is a signed value.. Since the value is a 24 bit one,
stored in a 32 bit variable, the sign should be extended in order to get
the correct representation.
Also the channel description has been updated to signed representation,
to match the ADC specifications.
Fixes: a5f8c7da3dbe ("iio: adc: Add AD7768-1 ADC basic support")
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://patch.msgid.link/505994d3b71c2aa38ba714d909a68e021f12124c.1741268122.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
return value check
[ Upstream commit 0af1c801a15225304a6328258efbf2bee245c654 ]
The data used is all in local variables so there is no advantage
in setting *val = ret with the direct mode claim held.
Move it later to after error check.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-13-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 8236644f5ecb ("iio: adc: ad7768-1: Fix conversion result sign")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2416cec859299be04d021b4cf98eff814f345af7 ]
Datasheet recommends Setting the MOSI idle state to high in order to
prevent accidental reset of the device when SCLK is free running.
This happens when the controller clocks out a 1 followed by 63 zeros
while the CS is held low.
Check if SPI controller supports SPI_MOSI_IDLE_HIGH flag and set it.
Fixes: a5f8c7da3dbe ("iio: adc: Add AD7768-1 ADC basic support")
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/c2a2b0f3d54829079763a5511359a1fa80516cfb.1741268122.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7b6033ed5a9e1a369a9cf58018388ae4c5f17e41 ]
Checking the binary representation of two structs (of the same type)
for equality doesn't have the same semantic as comparing all members for
equality. The former might find a difference where the latter doesn't in
the presence of padding or when ambiguous types like float or bool are
involved. (Floats typically have different representations for single
values, like -0.0 vs +0.0, or 0.5 * 2² vs 0.25 * 2³. The type bool has
at least 8 bits and the raw values 1 and 2 (probably) both evaluate to
true, but memcmp finds a difference.)
When searching for a channel that already has the configuration we need,
the comparison by member is the one that is needed.
Convert the comparison accordingly to compare the members one after
another. Also add a static_assert guard to (somewhat) ensure that when
struct ad7173_channel_config::config_props is expanded, the comparison
is adapted, too.
This issue is somewhat theoretic, but using memcmp() on a struct is a
bad pattern that is worth fixing.
Fixes: 76a1e6a42802 ("iio: adc: ad7173: add AD7173 driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-14-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 05a5d874f7327b75e9bc4359618017e047cc129c ]
Checking the binary representation of two structs (of the same type)
for equality doesn't have the same semantic as comparing all members for
equality. The former might find a difference where the latter doesn't in
the presence of padding or when ambiguous types like float or bool are
involved. (Floats typically have different representations for single
values, like -0.0 vs +0.0, or 0.5 * 2² vs 0.25 * 2³. The type bool has
at least 8 bits and the raw values 1 and 2 (probably) both evaluate to
true, but memcmp finds a difference.)
When searching for a channel that already has the configuration we need,
the comparison by member is the one that is needed.
Convert the comparison accordingly to compare the members one after
another. Also add a static_assert guard to (somewhat) ensure that when
struct ad7124_channel_config::config_props is expanded, the comparison
is adapted, too.
This issue is somewhat theoretic, but using memcmp() on a struct is a
bad pattern that is worth fixing.
Fixes: 7b8d045e497a ("iio: adc: ad7124: allow more than 8 channels")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-13-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 280acb19824663d55a3f4d09087c76fabe86fa3c ]
Checking the binary representation of two structs (of the same type)
for equality doesn't have the same semantic as comparing all members for
equality. The former might find a difference where the latter doesn't in
the presence of padding or when ambiguous types like float or bool are
involved. (Floats typically have different representations for single
values, like -0.0 vs +0.0, or 0.5 * 2² vs 0.25 * 2³. The type bool has
at least 8 bits and the raw values 1 and 2 (probably) both evaluate to
true, but memcmp finds a difference.)
When searching for a channel that already has the configuration we need,
the comparison by member is the one that is needed.
Convert the comparison accordingly to compare the members one after
another. Also add a static_assert guard to (somewhat) ensure that when
struct ad4130_setup_info is expanded, the comparison is adapted, too.
This issue is somewhat theoretic, but using memcmp() on a struct is a
bad pattern that is worth fixing.
Fixes: 62094060cf3a ("iio: adc: ad4130: add AD4130 driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-12-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit aa5119c36d19639397d29ef305aa53a5ecd72b27 upstream.
The number of valid bits in SAMA7G5 ADC channel data register are 16.
Hence changing the realbits value to 16
Fixes: 840bf6cb983f ("iio: adc: at91-sama5d2_adc: add support for sama7g5 device")
Signed-off-by: Nayab Sayed <nayabbasha.sayed@microchip.com>
Link: https://patch.msgid.link/20250115-fix-sama7g5-adc-realbits-v2-1-58a6e4087584@microchip.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21d7241faf406e8aee3ce348451cc362d5db6a02 upstream.
Channel configuration doesn't work as expected.
For FIELD_PREP the bit mask is needed and not the bit number.
Fixes: 874bbd1219c7 ("iio: adc: ad7192: Use bitfield access macros")
Signed-off-by: Markus Burri <markus.burri@mt.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250124150703.97848-1-markus.burri@mt.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4be339af334c283a1a1af3cb28e7e448a0aa8a7c upstream.
When during a measurement two channels are enabled, two measurements are
done that are reported sequencially in the DATA register. As the code
triggered by reading one of the sysfs properties expects that only one
channel is enabled it only reads the first data set which might or might
not belong to the intended channel.
To prevent this situation disable all channels during probe. This fixes
a problem in practise because the reset default for channel 0 is
enabled. So all measurements before the first measurement on channel 0
(which disables channel 0 at the end) might report wrong values.
Fixes: 7b8d045e497a ("iio: adc: ad7124: allow more than 8 channels")
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20241104101905.845737-2-u.kleine-koenig@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36a44e05cd807a54e5ffad4b96d0d67f68ad8576 upstream.
Fix a possible race condition during driver probe in the ad7173 driver
due to using a shared static info struct. If more that one instance of
the driver is probed at the same time, some of the info could be
overwritten by the other instance, leading to incorrect operation.
To fix this, make the static info struct const so that it is read-only
and make a copy of the info struct for each instance of the driver that
can be modified.
Reported-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Fixes: 76a1e6a42802 ("iio: adc: ad7173: add AD7173 driver")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Tested-by: Guillaume Ranquet <granquet@baylibre.com>
Link: https://patch.msgid.link/20241127-iio-adc-ad7313-fix-non-const-info-struct-v2-1-b6d7022b7466@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de6a73bad1743e9e81ea5a24c178c67429ff510b upstream.
Current implementation of at91_ts_register() calls input_free_deivce()
on st->ts_input, however, the err label can be reached before the
allocated iio_dev is stored to st->ts_input. Thus call
input_free_device() on input instead of st->ts_input.
Fixes: 84882b060301 ("iio: adc: at91_adc: Add support for touchscreens without TSMR")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://patch.msgid.link/20241207043045.1255409-1-joe@pf.is.s.u-tokyo.ac.jp
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a8e34096ec70d73ebb6d9920688ea312700cbd9 upstream.
Using gpiod_set_value() to control the reset GPIO causes some verbose
warnings during boot when the reset GPIO is controlled by an I2C IO
expander.
As the caller can sleep, use the gpiod_set_value_cansleep() variant to
fix the issue.
Tested on a custom i.MX93 board with a ADS124S08 ADC.
Cc: stable@kernel.org
Fixes: e717f8c6dfec ("iio: adc: Add the TI ads124s08 ADC code")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://patch.msgid.link/20241122164308.390340-1-festevam@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bcb394bb28e55312cace75362b8e489eb0e02a30 upstream.
devm_kasprintf() can return a NULL pointer on failure. A check on the
return value of such a call in ads1298_init() is missing. Add it.
Fixes: 00ef7708fa60 ("iio: adc: ti-ads1298: Add driver")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://patch.msgid.link/20241118090208.14586-1-hanchunchao@inspur.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54d394905c92b9ecc65c1f9b2692c8e10716d8e1 upstream.
This device returns signed, 16-bit samples as stated in its datasheet
(see 8.5.2 Data Format). That is in line with the scan_type definition
for the IIO_VOLTAGE channel, but 'unsigned int' is being used to read
and push the data to userspace.
Given that the size of that type depends on the architecture (at least
2 bytes to store values up to 65535, but its actual size is often 4
bytes), use the 's16' type to provide the same structure in all cases.
Fixes: a9306887eba4 ("iio: adc: ti-ads1119: Add driver")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20241202-ti-ads1119_s16_chan-v1-1-fafe3136dc90@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 75f339d3ecd38cb1ce05357d647189d4a7f7ed08 upstream.
The 'scan' local struct is used to push data to user space from a
triggered buffer, but it has a hole between the sample (unsigned int)
and the timestamp. This hole is never initialized.
Initialize the struct to zero before using it to avoid pushing
uninitialized information to userspace.
Cc: stable@vger.kernel.org
Fixes: a9306887eba4 ("iio: adc: ti-ads1119: Add driver")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20241125-iio_memset_scan_holes-v1-2-0cb6e98d895c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a7377ccfd940cd6e9201756aff1e7852c266e69 upstream.
The 'buffer' local array is used to push data to user space from a
triggered buffer, but it does not set values for inactive channels, as
it only uses iio_for_each_active_channel() to assign new values.
Initialize the array to zero before using it to avoid pushing
uninitialized information to userspace.
Cc: stable@vger.kernel.org
Fixes: 61fa5dfa5f52 ("iio: adc: ti-ads8688: Fix alignment of buffer in iio_push_to_buffers_with_timestamp()")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241125-iio_memset_scan_holes-v1-8-0cb6e98d895c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 38724591364e1e3b278b4053f102b49ea06ee17c upstream.
The 'data' local struct is used to push data to user space from a
triggered buffer, but it does not set values for inactive channels, as
it only uses iio_for_each_active_channel() to assign new values.
Initialize the struct to zero before using it to avoid pushing
uninitialized information to userspace.
Cc: stable@vger.kernel.org
Fixes: 4e130dc7b413 ("iio: adc: rockchip_saradc: Add support iio buffers")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241125-iio_memset_scan_holes-v1-4-0cb6e98d895c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b7f99fa1b64af2f696b13cec581cb4cd7d3982b8 ]
spi_get_device_match_data() can return a NULL pointer. Hence, let's
check for it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20241014-fix-error-check-v1-1-089e1003d12f@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3a4187ec454e19903fd15f6e1825a4b84e59a4cd upstream.
The AD7923 was updated to support devices with 8 channels, but the size
of tx_buf and ring_xfer was not increased accordingly, leading to a
potential buffer overflow in ad7923_update_scan_mode().
Fixes: 851644a60d20 ("iio: adc: ad7923: Add support for the ad7908/ad7918/ad7928")
Cc: stable@vger.kernel.org
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Zicheng Qu <quzicheng@huawei.com>
Link: https://patch.msgid.link/20241029134637.2261336-1-quzicheng@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c174b53e95adf2eece2afc56cd9798374919f99a upstream.
In the ad7780_write_raw() , val2 can be zero, which might lead to a
division by zero error in DIV_ROUND_CLOSEST(). The ad7780_write_raw()
is based on iio_info's write_raw. While val is explicitly declared that
can be zero (in read mode), val2 is not specified to be non-zero.
Fixes: 9085daa4abcc ("staging: iio: ad7780: add gain & filter gpio support")
Cc: stable@vger.kernel.org
Signed-off-by: Zicheng Qu <quzicheng@huawei.com>
Link: https://patch.msgid.link/20241028142027.1032332-1-quzicheng@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 869aa5e847696bcda8966be9d03de2560226bcc3 ]
Even if it's not critical, the avoidance of checking the error code
from devm_mutex_init() call today diminishes the point of using devm
variant of it. Tomorrow it may even leak something. Add the missed
check.
Fixes: 371f778b83cd ("iio: adc: add support for pac1921")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Matteo Martelli <matteomartelli3@gmail.com>
Link: https://patch.msgid.link/20241030162013.2100253-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8ebfd09255219ae55f8a101f6aeb0f64dd780d88 ]
Even if it's not critical, the avoidance of checking the error code
from devm_mutex_init() call today diminishes the point of using devm
variant of it. Tomorrow it may even leak something. Add the missed
check.
Fixes: 938fd562b974 ("iio: adc: Add support for AD4000")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241030162013.2100253-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 62dd96ac9cdf2814f41cfc55ecaf22a28aad6ccb ]
Fix reading unsigned data from the AD4000 ADC via the _raw sysfs
attribute by ensuring that *val is set before returning from
ad4000_single_conversion(). This was not being set in any code path
and was causing the attribute to return a random value.
Fixes: 938fd562b974 ("iio: adc: Add support for AD4000")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241030-iio-adc-ad4000-fix-reading-unsigned-data-v1-1-2e28dd75fe29@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
In the ad7124_write_raw() function, parameter val can potentially
be zero. This may lead to a division by zero when DIV_ROUND_CLOSEST()
is called within ad7124_set_channel_odr(). The ad7124_write_raw()
function is invoked through the sequence: iio_write_channel_raw() ->
iio_write_channel_attribute() -> iio_channel_write(), with no checks
in place to ensure val is non-zero.
Cc: stable@vger.kernel.org
Fixes: 7b8d045e497a ("iio: adc: ad7124: allow more than 8 channels")
Signed-off-by: Zicheng Qu <quzicheng@huawei.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20241022134330.574601-1-quzicheng@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ad7380-4 is the only device in the family that does not have an internal
reference. It uses "refin" as a required external reference.
All other devices in the family use "refio"" as an optional external
reference.
Fixes: 737413da8704 ("iio: adc: ad7380: add support for ad738x-4 4 channels variants")
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241022-ad7380-fix-supplies-v3-4-f0cefe1b7fa6@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
vcc and vlogic are required but are not retrieved and enabled in the
probe. Add them.
In order to prepare support for additional parts requiring different
supplies, add vcc and vlogic to the platform specific structures
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241022-ad7380-fix-supplies-v3-3-f0cefe1b7fa6@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use devm_regulator_get_enable_read_voltage() to simplify the code.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241022-ad7380-fix-supplies-v3-2-f0cefe1b7fa6@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
IIO: 1st set of fixes for the 6.12 cycle.
Most of this pull request is the result of Javier Carrasco doing a
careful audit for missing Kconfig dependencies that luck has meant
the random builds have never hit. The rest is the usual mix of old
bugs that have surfaced and some fallout from the recent merge window.
adi,ad5686
- Fix binding duplication of compatible strings.
bosch,bma400
- Fix an uninitialized variable in the event tap handling.
bosch,bmi323
- Fix several issues in the register saving and restore on suspend/resume
sensiron,spd500
- Fix missing CRC8 dependency
ti,op3001
- Fix a missing full-scale range value (values above this point were
all reported wrongly)
vishay,veml6030
- Fix a segmentation fault due to some type confusion.
- Fix wrong ambient light sensor resolution.
* tag 'iio-fixes-for-6.12a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (34 commits)
iio: frequency: admv4420: fix missing select REMAP_SPI in Kconfig
iio: frequency: {admv4420,adrf6780}: format Kconfig entries
iio: adc: ad4695: Add missing Kconfig select
iio: adc: ti-ads8688: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: hid-sensors: Fix an error handling path in _hid_sensor_set_report_latency()
iioc: dac: ltc2664: Fix span variable usage in ltc2664_channel_config()
iio: dac: stm32-dac-core: add missing select REGMAP_MMIO in Kconfig
iio: dac: ltc1660: add missing select REGMAP_SPI in Kconfig
iio: dac: ad5770r: add missing select REGMAP_SPI in Kconfig
iio: amplifiers: ada4250: add missing select REGMAP_SPI in Kconfig
iio: frequency: adf4377: add missing select REMAP_SPI in Kconfig
iio: resolver: ad2s1210: add missing select (TRIGGERED_)BUFFER in Kconfig
iio: resolver: ad2s1210 add missing select REGMAP in Kconfig
iio: proximity: mb1232: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: pressure: bm1390: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: magnetometer: af8133j: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: light: bu27008: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: chemical: ens160: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: dac: ad5766: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: dac: ad3552r: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
...
|
|
Add select IIO_BUFFER and select IIO_TRIGGERED_BUFFER to the Kconfig for
the ad4695 driver.
Fixes: 6cc7e4bf2e08 ("iio: adc: ad4695: implement triggered buffer")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241009-iio-adc-ad4695-fix-kconfig-v1-1-e2a4dfde8d55@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This driver makes use of triggered buffers, but does not select the
required modules.
Fixes: 2a86487786b5 ("iio: adc: ti-ads8688: add trigger and buffer support")
Add the missing 'select IIO_BUFFER' and 'select IIO_TRIGGERED_BUFFER'.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20241003-iio-select-v1-4-67c0385197cd@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This driver makes use of triggered buffers, but does not select the
required modules.
Add the missing 'select IIO_BUFFER' and 'select IIO_TRIGGERED_BUFFER'.
Fixes: 6c7bc1d27bb2 ("iio: adc: ti-lmp92064: add buffering support")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-iio-select-v1-6-67c0385197cd@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This driver makes use of regmap_spi, but does not select the required
module.
Add the missing 'select REGMAP_SPI'.
Fixes: 627198942641 ("iio: adc: add ADC driver for the TI LMP92064 controller")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241003-iio-select-v1-5-67c0385197cd@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
