| Age | Commit message (Collapse) | Author |
|---|
|
This patch introduces basic I2C support for the SpacemiT K1 SoC,
utilizing interrupts for transfers.
The driver has been tested using i2c-tools on a Bananapi-F3 board,
and basic I2C read/write operations have been confirmed to work.
Signed-off-by: Troy Mitchell <troymitchell988@gmail.com>
Reviewed-by: Alex Elder <elder@riscstar.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250319-k1-i2c-master-v8-2-013e2df2b78d@gmail.com
|
|
Some SoCs require muxes in the routing for SDA and SCL lines.
Therefore, add support for setting the mux by reading the mux-states
property from the dt-node.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20250318103622.29979-3-j-choudhary@ti.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The driver gives the illusion of 10-bit address support, but the upper
3 bits of the given address are always thrown away. Remove unnecessary
considerations for 10 bit addressing and always complete 7 bit ops when
using the hlc methods.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20250318021632.2710792-3-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Kernel-docs require a ':' to signify the return behaviour of a function
with within the comment. Many functions in this file were missing ':'
after the "Returns" line, resulting in kernel-doc warnings.
Add the ':' to satisfy kernel-doc requirements.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20250318021632.2710792-2-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Newer versions of supported chips support MMIO in addition to legacy
PMIO register access. Probe the MMIO PCI BAR and use faster MMIO
register access if available.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/b4748b7a-aac5-445c-b813-20c4d2c23ec3@gmail.com
|
|
Switch to iomapped register access as a prerequisite for adding
support for MMIO register access.
This changes replaces the delayed inb_p()/outb_p() calls with calls to
ioread8()/iowrite8() which don't have this extra delay. According to
Documentation/driver-api/device-io.rst the _p versions are needed
for ISA device access only, therefore switching to the non-delayed
versions should not cause problems. However a certain risk remains,
which on the other hand is significantly reduced by the fact that
recent systems will use MMIO instead of PIO. ICH7 datasheet from 2012
mentions already that SMBus register space is also memory-mapped.
So all systems from at least the last 10 yrs should be safe.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/67535b17-c3fb-4507-b083-9c1884b4dd7d@gmail.com
|
|
irq allocated with devm_request_irq() will be freed in devm_irq_release(),
using free_irq() in ->remove() will causes a dangling pointer, and a
subsequent double free. So remove the free_irq() in the error path and
remove path.
Fixes: 969864efae78 ("i2c: amd-mp2: use msix/msi if the hardware supports")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20221103121146.99836-1-yangyingliang@huawei.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
In my tests terminating a transaction took about 25ms, what is
in line with the chip-internal timeout as described in 5.21.3.2
"Bus Time Out" in [0]. Therefore the 2ms delay is too low.
Instead of a fixed delay let's use i801_wait_intr() here,
this also facilitates the status handling.
This potential issue seems to have been existing forever, but as no
related problem is known, treat it as an improvement.
[0] Intel document #326776-003, 7 Series PCH datasheet
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/ad4ef645-5d03-4833-a0b6-f31f8fd06483@gmail.com
|
|
Move both functions to avoid forward declarations in a subsequent patch.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/a60ee54b-c5e8-4bdb-9f1f-8889f4dcd114@gmail.com
|
|
- Use pci_err et al instead of dev_err to simplify the code
- use format %pr to print resource
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/6676001a-a584-46e2-a98e-17163d82c218@gmail.com
|
|
probe error path
Ensure reset_control_assert() is called after pm_runtime_set_suspended()
in the cdns_i2c_probe exit path to maintain proper power management
sequence in error cases.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250206115708.1085523-3-manikanta.guntupalli@amd.com
|
|
Clock handling can be very simplified with using devm_clk_get_enabled() as
was done by commit 8d2aaf4382b7 ("gpio: zynq: Simplify using
devm_clk_get_enabled()").
And also fix issue in connection to incorrect sequence when err_clk_dis
label is called.
When reset_control_deassert() fails it jumps to err_clk_dis label which
disables clock and also disable pm_runtime setup but nothing has been setup
at this time of failure because initialization is done below
reset_control_deassert() call.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250206115708.1085523-2-manikanta.guntupalli@amd.com
|
|
Corrected a spelling mistake in the i2c-exynos5 driver to improve code
readability. No functional changes were made.
Signed-off-by: Anindya Sundar Gayen <anindya.sg@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250228133745.35053-1-anindya.sg@samsung.com
|
|
Use i2c_*bit_addr*_from_msg() helpers instead of local copy.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213141045.2716943-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use i2c_*bit_addr*_from_msg() helpers instead of local copy.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213141045.2716943-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use i2c_10bit_addr_*_from_msg() helpers instead of local copy.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213141045.2716943-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use i2c_10bit_addr_*_from_msg() helpers instead of local copy.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213141045.2716943-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use i2c_10bit_addr_*_from_msg() helpers instead of local copy.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213141045.2716943-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use i2c_10bit_addr_*_from_msg() helpers instead of local copy.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213141045.2716943-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use i2c_10bit_addr_*_from_msg() helpers instead of local copy.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213141045.2716943-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use i2c_10bit_addr_*_from_msg() helpers instead of local copy.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213141045.2716943-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use i2c_10bit_addr_*_from_msg() helpers instead of local copy.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213141045.2716943-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
When the I2C QUP controller is used together with a DMA engine it needs
to vote for the interconnect path to the DRAM. Otherwise it may be
unable to access the memory quickly enough.
The requested peak bandwidth is dependent on the I2C core clock.
To avoid sending votes too often the bandwidth is always requested when
a DMA transfer starts, but dropped only on runtime suspend. Runtime
suspend should only happen if no transfer is active. After resumption we
can defer the next vote until the first DMA transfer actually happens.
The implementation is largely identical to the one introduced for
spi-qup in commit ecdaa9473019 ("spi: qup: Vote for interconnect
bandwidth to DRAM") since both drivers represent the same hardware
block.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20231128-i2c-qup-dvfs-v1-3-59a0e3039111@kernkonzept.com
|
|
Building with W=1 shows a warning about ltc4306_of_match and
i2c_mux_reg_of_match being unused when CONFIG_OF is disabled:
drivers/i2c/muxes/i2c-mux-ltc4306.c:200:34: error: unused variable 'ltc4306_of_match' [-Werror,-Wunused-const-variable]
drivers/i2c/muxes/i2c-mux-reg.c:242:34: error: unused variable 'i2c_mux_reg_of_match' [-Werror,-Wunused-const-variable]
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250225163700.4169480-1-arnd@kernel.org
|
|
In the event of ASF error during the transfer, update the cmd and exit
the process, as data processing is not performed when a command fails.
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250217090258.398540-2-Shyam-sundar.S-k@amd.com
|
|
revision
Adjust the i2c_algorithm callbacks to be consistent with the most recent
revision by updating the callback names from master_xfer, reg_slave, and
unreg_slave to the current naming convention: xfer, reg_target, and
unreg_target.
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250217090258.398540-1-Shyam-sundar.S-k@amd.com
|
|
In light of the recent updates to the i2c subsystem, ensure to use the
correct callback names. Specifically, replace '.master_xfer' with '.xfer'.
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250217124709.3121848-2-Shyam-sundar.S-k@amd.com
|
|
Instead of using the 'goto label; mutex_unlock()' pattern use
'guard(mutex)' which will release the mutex when it goes out of scope.
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250217124709.3121848-1-Shyam-sundar.S-k@amd.com
|
|
If the clock i2c->clk was not enabled in i2c_pxa_probe(), it should not be
disabled in any path.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250212172803.1422136-1-mordan@ispras.ru
|
|
Refactor the current implementation of the high-level composite read and
write operations in preparation of the addition of block-mode read/write
operations.
The sending of the i2c command is generic and will apply for both the
block-mode and non-block-mode ops. Extract this from the current hlc
ops, and place into a generic function, octeon_i2c_hlc_cmd_send.
The considerations made for extended addresses in the command
construction are almost common for all cases, extract these into
octeon_i2c_hlc_ext. There is one difference between the extended read
and write cases. When performing extended read or writes the SW_TWSI_EXT
must be written with an extended internal address, but the data field is
only filled in the write case (read back in read case). This results in
the original code block for the read case immediately writing this
register, while the write case fills in any data and then writes the
register. To create a common block of code for both processes remove the
SW_TWSI_EXT write from within the code block and instead in it's place a
variable is set, set_ext, which is returned and used as a condition to
do the register write, in the read command case.
There are parts of the commands construction which are common (only in
the read case), extract this and place into generic function
octeon_i2c_hlc_read_cmd. This function also reads the return from
octeon_i2c_hlc_ext and completes the write to SW_TWSI_EXT if required.
The write commands cannot be made entirely into common code as there are
distinct differences in the block mode and non-block-mode process.
Particularly the writing of data into the buffer.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20241010025317.2040470-2-aryan.srivastava@alliedtelesis.co.nz
|
|
If i2c_add_adapter() fails, the request_region() call in sis630_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/3d607601f2c38e896b10207963c6ab499ca5c307.1741033587.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
If i2c_add_adapter() fails, the request_region() call in ali15x3_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/9b2090cbcc02659f425188ea05f2e02745c4e67b.1741031878.git.christophe.jaillet@wanadoo.fr
|
|
If i2c_add_adapter() fails, the request_region() call in ali1535_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/0daf63d7a2ce74c02e2664ba805bbfadab7d25e5.1741031571.git.christophe.jaillet@wanadoo.fr
|
|
On the GTA04A5 writing a reset command to the gyroscope causes IRQ
storms because NACK IRQs are enabled and therefore triggered but not
acked.
Sending a reset command to the gyroscope by
i2cset 1 0x69 0x14 0xb6
with an additional debug print in the ISR (not the thread) itself
causes
[ 363.353515] i2c i2c-1: ioctl, cmd=0x720, arg=0xbe801b00
[ 363.359039] omap_i2c 48072000.i2c: addr: 0x0069, len: 2, flags: 0x0, stop: 1
[ 363.366180] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x1110)
[ 363.371673] omap_i2c 48072000.i2c: IRQ (ISR = 0x0010)
[ 363.376892] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.382263] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.387664] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
repeating till infinity
[...]
(0x2 = NACK, 0x100 = Bus free, which is not enabled)
Apparently no other IRQ bit gets set, so this stalls.
Do not ignore enabled interrupts and make sure they are acked.
If the NACK IRQ is not needed, it should simply not enabled, but
according to the above log, caring about it is necessary unless
the Bus free IRQ is enabled and handled. The assumption that is
will always come with a ARDY IRQ, which was the idea behind
ignoring it, proves wrong.
It is true for simple reads from an unused address.
To still avoid the i2cdetect trouble which is the reason for
commit c770657bd261 ("i2c: omap: Fix standard mode false ACK readings"),
avoid doing much about NACK in omap_i2c_xfer_data() which is used
by both IRQ mode and polling mode, so also the false detection fix
is extended to polling usage and IRQ storms are avoided.
By changing this, the hardirq handler is not needed anymore to filter
stuff.
The mentioned gyro reset now just causes a -ETIMEDOUT instead of
hanging the system.
Fixes: c770657bd261 ("i2c: omap: Fix standard mode false ACK readings").
CC: stable@kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250228140420.379498-1-andreas@kemnade.info
|
|
The commit b1f8921dfbaa
("i2c: amd-asf: Clear remote IRR bit to get successive interrupt")
introduced a method to enable successive interrupts but inadvertently
omitted the necessary write to the EOI register, resulting in a failure to
receive successive interrupts.
Fix this by adding the required write to the EOI register.
Fixes: b1f8921dfbaa ("i2c: amd-asf: Clear remote IRR bit to get successive interrupt")
Cc: stable@vger.kernel.org # v6.13+
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Fixes: 9b25419ad397 ("i2c: amd-asf: Add routine to handle the ASF slave process")
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250219135747.3251182-1-Shyam-sundar.S-k@amd.com
|
|
According to the chip manual, the I2C register access type of
Loongson-2K2000/LS7A is "B", so we can only access registers in byte
form (readb()/writeb()).
Although Loongson-2K0500/Loongson-2K1000 do not have similar
constraints, register accesses in byte form also behave correctly.
Also, in hardware, the frequency division registers are defined as two
separate registers (high 8-bit and low 8-bit), so we just access them
directly as bytes.
Fixes: 015e61f0bffd ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller")
Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Cc: stable@vger.kernel.org # v6.3+
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250220125612.1910990-1-zhoubinbin@loongson.cn
|
|
The customer reports that there is a soft lockup issue related to
the i2c driver. After checking, the i2c module was doing a tx transfer
and the bmc machine reboots in the middle of the i2c transaction, the i2c
module keeps the status without being reset.
Due to such an i2c module status, the i2c irq handler keeps getting
triggered since the i2c irq handler is registered in the kernel booting
process after the bmc machine is doing a warm rebooting.
The continuous triggering is stopped by the soft lockup watchdog timer.
Disable the interrupt enable bit in the i2c module before calling
devm_request_irq to fix this issue since the i2c relative status bit
is read-only.
Here is the soft lockup log.
[ 28.176395] watchdog: BUG: soft lockup - CPU#0 stuck for 26s! [swapper/0:1]
[ 28.183351] Modules linked in:
[ 28.186407] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.15.120-yocto-s-dirty-bbebc78 #1
[ 28.201174] pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 28.208128] pc : __do_softirq+0xb0/0x368
[ 28.212055] lr : __do_softirq+0x70/0x368
[ 28.215972] sp : ffffff8035ebca00
[ 28.219278] x29: ffffff8035ebca00 x28: 0000000000000002 x27: ffffff80071a3780
[ 28.226412] x26: ffffffc008bdc000 x25: ffffffc008bcc640 x24: ffffffc008be50c0
[ 28.233546] x23: ffffffc00800200c x22: 0000000000000000 x21: 000000000000001b
[ 28.240679] x20: 0000000000000000 x19: ffffff80001c3200 x18: ffffffffffffffff
[ 28.247812] x17: ffffffc02d2e0000 x16: ffffff8035eb8b40 x15: 00001e8480000000
[ 28.254945] x14: 02c3647e37dbfcb6 x13: 02c364f2ab14200c x12: 0000000002c364f2
[ 28.262078] x11: 00000000fa83b2da x10: 000000000000b67e x9 : ffffffc008010250
[ 28.269211] x8 : 000000009d983d00 x7 : 7fffffffffffffff x6 : 0000036d74732434
[ 28.276344] x5 : 00ffffffffffffff x4 : 0000000000000015 x3 : 0000000000000198
[ 28.283476] x2 : ffffffc02d2e0000 x1 : 00000000000000e0 x0 : ffffffc008bdcb40
[ 28.290611] Call trace:
[ 28.293052] __do_softirq+0xb0/0x368
[ 28.296625] __irq_exit_rcu+0xe0/0x100
[ 28.300374] irq_exit+0x14/0x20
[ 28.303513] handle_domain_irq+0x68/0x90
[ 28.307440] gic_handle_irq+0x78/0xb0
[ 28.311098] call_on_irq_stack+0x20/0x38
[ 28.315019] do_interrupt_handler+0x54/0x5c
[ 28.319199] el1_interrupt+0x2c/0x4c
[ 28.322777] el1h_64_irq_handler+0x14/0x20
[ 28.326872] el1h_64_irq+0x74/0x78
[ 28.330269] __setup_irq+0x454/0x780
[ 28.333841] request_threaded_irq+0xd0/0x1b4
[ 28.338107] devm_request_threaded_irq+0x84/0x100
[ 28.342809] npcm_i2c_probe_bus+0x188/0x3d0
[ 28.346990] platform_probe+0x6c/0xc4
[ 28.350653] really_probe+0xcc/0x45c
[ 28.354227] __driver_probe_device+0x8c/0x160
[ 28.358578] driver_probe_device+0x44/0xe0
[ 28.362670] __driver_attach+0x124/0x1d0
[ 28.366589] bus_for_each_dev+0x7c/0xe0
[ 28.370426] driver_attach+0x28/0x30
[ 28.373997] bus_add_driver+0x124/0x240
[ 28.377830] driver_register+0x7c/0x124
[ 28.381662] __platform_driver_register+0x2c/0x34
[ 28.386362] npcm_i2c_init+0x3c/0x5c
[ 28.389937] do_one_initcall+0x74/0x230
[ 28.393768] kernel_init_freeable+0x24c/0x2b4
[ 28.398126] kernel_init+0x28/0x130
[ 28.401614] ret_from_fork+0x10/0x20
[ 28.405189] Kernel panic - not syncing: softlockup: hung tasks
[ 28.411011] SMP: stopping secondary CPUs
[ 28.414933] Kernel Offset: disabled
[ 28.418412] CPU features: 0x00000000,00000802
[ 28.427644] Rebooting in 20 seconds..
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250220040029.27596-2-kfting@nuvoton.com
|
|
drivers/i2c/i2c-core-base.c: In function ‘i2c_detect.isra’:
drivers/i2c/i2c-core-base.c:2544:1: warning: the frame size of 1312 bytes is larger than 1024 bytes [-Wframe-larger-than=]
2544 | }
| ^
Fix this by allocating the temporary client structure dynamically, as it
is a rather large structure (1216 bytes, depending on kernel config).
This is basically a revert of the to-be-fixed commit with some
checkpatch improvements.
Fixes: 735668f8e5c9 ("i2c: core: Allocate temp client on the stack in i2c_detect")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
[wsa: updated commit message, merged tags from similar patch]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/6a0d31244560b76cc7e76954bf68dbe14a4761e3.1738746904.git.namcao@linutronix.de
|
|
i2c_of_match_device() is not used anymore outside of I²C framework,
unexport it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
This reverts commit 56a50667cbcfaf95eea9128d5676af94e54b51a8. Mux
handling is not sufficiently implemented. It needs more time.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
clients"
This reverts commit 3cfe39b3a845593a485ab1c716615979004ef9f6. Mux
handling is not sufficiently implemented. It needs more time.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- add a missing Kconfig dependency for imx-lpi2c
- in the core, handle the new per-client debugfs directory during
probe/remove, not during {un}register
* tag 'i2c-for-6.14-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: Fix core-managed per-client debugfs handling
i2c: imx-lpi2c: select CONFIG_I2C_SLAVE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the big set of driver core and debugfs updates for 6.14-rc1.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at
least one user that does have a regression with these, but Al is
working on tracking down the fix for it. In my use (and everyone
else's linux-next use), it does not seem like a big issue at the
moment.
Here's a short list of the things in here:
- driver core rust bindings for PCI, platform, OF, and some i/o
functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing
things in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon""
* tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
rust: device: Use as_char_ptr() to avoid explicit cast
rust: device: Replace CString with CStr in property_present()
devcoredump: Constify 'struct bin_attribute'
devcoredump: Define 'struct bin_attribute' through macro
rust: device: Add property_present()
saner replacement for debugfs_rename()
orangefs-debugfs: don't mess with ->d_name
octeontx2: don't mess with ->d_parent or ->d_parent->d_name
arm_scmi: don't mess with ->d_parent->d_name
slub: don't mess with ->d_name
sof-client-ipc-flood-test: don't mess with ->d_name
qat: don't mess with ->d_name
xhci: don't mess with ->d_iname
mtu3: don't mess wiht ->d_iname
greybus/camera - stop messing with ->d_iname
mediatek: stop messing with ->d_iname
netdevsim: don't embed file_operations into your structs
b43legacy: make use of debugfs_get_aux()
b43: stop embedding struct file_operations into their objects
carl9170: stop embedding file_operations into their objects
...
|
|
The debugfs directory should be created when a device
is probed, not when it is registered. It should be removed
when the device is removed, not when it is unregistered.
Fixes: d06905d68610 ("i2c: add core-managed per-client directory in debugfs")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The addition of target mode causes a build failure when CONFIG_I2C_SLAVE
is turned off:
drivers/i2c/busses/i2c-imx-lpi2c.c:1273:10: error: 'const struct i2c_algorithm' has no member named 'reg_target'
1273 | .reg_target = lpi2c_imx_register_target,
| ^~~~~~~~~~
drivers/i2c/busses/i2c-imx-lpi2c.c:1274:10: error: 'const struct i2c_algorithm' has no member named 'unreg_target'
1274 | .unreg_target = lpi2c_imx_unregister_target,
| ^~~~~~~~~~~~
Select the Kconfig symbol like we do for other similar drivers.
Fixes: 1ee867e465c1 ("i2c: imx-lpi2c: add target mode support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Ilpo Järvinen:
"acer-wmi:
- Add support for PH14-51, PH16-72, and Nitro AN515-58
- Add proper hwmon support
- Improve error handling when reading "gaming system info"
- Replace direct EC reads for the current platform profile with WMI
calls to handle EC address variations
- Replace custom platform_profile cycling with the generic one
ACPI:
- platform_profile: Major refactoring and improvements
- Support registering multiple platform_profile handlers concurrently
to avoid the need to quirk which handler takes precedence
- Support reporting "custom" profile for cases where the current
profile is ambiguous or when settings tweaks are done outside the
pre-defined profile
- Abstract and layer platform_profile API better using the class_dev
and drvdata
- Various minor improvements
- Add Documentation and kerneldoc
amd/hsmp:
- Add support for HSMP protocol v7
amd/pmc:
- Support AMD 1Ah family 70h
- Support STB with Ryzen desktop SoCs
amd/pmf:
- Support Custom BIOS inputs for PMF TA
- Support passing SRA sensor data from AMD SFH (HID) to PMF TA
dell-smo8800:
- Move SMO88xx quirk away from the generic i2c-i801 driver
- Add accelerometer support for Dell Latitude E6330/E6430 and XPS
9550
- Support probing accelerometer for models yet to be listed in the
DMI mapping table because ACPI lacks i2c-address for the
accelerometer (behind a module parameter because probing might be
dangerous)
HID:
- amd_sfh: Add support for exporting SRA sensor data
hp-wmi:
- Add fan and thermal support for Victus 16-s1000
input:
- Add key for phone linking
- i8042: Add context for the i8042 filter to enable cleaning up the
filter related global variables from pdx86 drivers
lenovo-wmi-camera:
- Use SW_CAMERA_LENS_COVER instead of KEY_CAMERA_ACCESS
mellanox mlxbf-pmc:
- Add support for monitoring cycle count
- Add Documentation
thinkpad_acpi:
- Add support for phone link key
tools/power/x86/intel-speed-select:
- Fix Turbo Ratio Limit restore
x86-android-tables:
- Add support for Vexia EDU ATLA 10 Bluetooth and EC battery driver
And miscellaneous cleanups / refactoring / improvements"
* tag 'platform-drivers-x86-v6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (133 commits)
platform/x86: acer-wmi: Fix initialization of last_non_turbo_profile
platform/x86: acer-wmi: Ignore AC events
platform/mellanox: mlxreg-io: use sysfs_emit() instead of sprintf()
platform/mellanox: mlxreg-hotplug: use sysfs_emit() instead of sprintf()
platform/mellanox: mlxbf-bootctl: use sysfs_emit() instead of sprintf()
platform/x86: hp-wmi: Add fan and thermal profile support for Victus 16-s1000
ACPI: platform_profile: Add a prefix to log messages
ACPI: platform_profile: Add documentation
ACPI: platform_profile: Clean platform_profile_handler
ACPI: platform_profile: Move platform_profile_handler
ACPI: platform_profile: Remove platform_profile_handler from exported symbols
platform/x86: thinkpad_acpi: Use devm_platform_profile_register()
platform/x86: inspur_platform_profile: Use devm_platform_profile_register()
platform/x86: hp-wmi: Use devm_platform_profile_register()
platform/x86: ideapad-laptop: Use devm_platform_profile_register()
platform/x86: dell-pc: Use devm_platform_profile_register()
platform/x86: asus-wmi: Use devm_platform_profile_register()
platform/x86: amd: pmf: sps: Use devm_platform_profile_register()
platform/x86: acer-wmi: Use devm_platform_profile_register()
platform/surface: surface_platform_profile: Use devm_platform_profile_register()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Core:
- list-based mechanisms for handling auto-detected and userspace
created clients are replaced with a flag-based approach. The
resulting code is much simpler as well as the locking.
- i2c clients now get a default debugfs dir managed by the I2C core.
Drivers don't have to maintain their own directory anymore.
Driver updates:
- xiic: atomic_transfer support
- imx-lpi2c: DMA and target mode support
- riic cleanups
- npcm: better timeout handling and more precise frequency setups
- davinci: remove unused platform_data
- at24: add new compatibles for variants from Giantec and Puya
Semiconductor (together with a new vendor prefix)"
* tag 'i2c-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: add kdoc for the new debugfs entry of clients
i2c: designware: Actually make use of the I2C_DW_COMMON and I2C_DW symbol namespaces
i2c: add core-managed per-client directory in debugfs
i2c: Force ELAN06FA touchpad I2C bus freq to 100KHz
i2c: riic: Add `riic_bus_barrier()` to check bus availability
i2c: riic: Use predefined macro and simplify clock tick calculation
i2c: riic: Mark riic_irqs array as const
i2c: riic: Make use of devres helper to request deasserted reset line
i2c: riic: Use GENMASK() macro for bitmask definitions
i2c: riic: Use BIT macro consistently
i2c: riic: Use local `dev` pointer in `dev_err_probe()`
i2c: riic: Use dev_err_probe in probe and riic_init_hw functions
i2c: riic: Introduce a separate variable for IRQ
i2c: amd756: Remove superfluous TODO
Revert "i2c: amd756: Fix endianness handling for word data"
i2c: i801: Add lis3lv02d for Dell Precision M6800
i2c: i801: Remove unnecessary PCI function call
i2c: core: Allocate temp client on the stack in i2c_detect
i2c: slave-eeprom: Constify 'struct bin_attribute'
i2c: imx-lpi2c: make controller available until the system enters suspend_noirq() and from resume_noirq().
...
|
|
This backend requests a NACK from the controller driver when it detects
an error. If that request gets ignored from some reason, subsequent
accesses will wrongly be handled OK. To fix this, an error now changes
the state machine, so the backend will report NACK until a STOP
condition has been detected. This make the driver more robust against
controllers which will sadly apply the NACK not to the current byte but
the next one.
Fixes: a8335c64c5f0 ("i2c: add slave testunit driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
When this controller is a target, the NACK handling had two issues.
First, the return value from the backend was not checked on the initial
WRITE_REQUESTED. So, the driver missed to send a NACK in this case.
Also, the NACK always arrives one byte late on the bus, even in the
WRITE_RECEIVED case. This seems to be a HW issue. We should then not
rely on the backend to correctly NACK the superfluous byte as well. Fix
both issues by introducing a flag which gets set whenever the backend
requests a NACK and keep sending it until we get a STOP condition.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
