| Age | Commit message (Collapse) | Author |
|---|
|
commit 5a72477273066b5b357801ab2d315ef14949d402 upstream.
Setting IACK bit when core is disabled does not clear the "Interrupt Flag"
bit in the status register, and the interrupt remains pending.
Sometimes it causes failure for the very first message transfer, that is
usually a device probe.
Hence, set IACK bit after core is enabled to clear pending interrupt.
Fixes: 18f98b1e3147 ("[PATCH] i2c: New bus driver for the OpenCores I2C controller")
Signed-off-by: Grygorii Tertychnyi <grygorii.tertychnyi@leica-geosystems.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cbf3fb5b29e99e3689d63a88c3cddbffa1b8de99 ]
When an I2C adapter acts only as a slave, it should not claim to
support I2C master capabilities.
Fixes: 5b6d721b266a ("i2c: designware: enable SLAVE in platform module")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Luis Oliveira <lolivei@synopsys.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Jan Dabros <jsd@semihalf.com>
Cc: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d6d5645e5fc1233a7ba950de4a72981c394a2557 ]
When an I2C adapter acts only as a slave, it should not claim to
support I2C master capabilities.
Fixes: 9d3ca54b550c ("i2c: at91: added slave mode support")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Juergen Fitschen <me@jue.yt>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Cc: Andi Shyti <andi.shyti@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3f858bbf04dbac934ac279aaee05d49eb9910051 upstream.
There is an issue with ACPI overlay table removal specifically related
to I2C multiplexers.
Consider an ACPI SSDT Overlay that defines a PCA9548 I2C mux on an
existing I2C bus. When this table is loaded we see the creation of a
device for the overall PCA9548 chip and 8 further devices - one
i2c_adapter each for the mux channels. These are all bound to their
ACPI equivalents via an eventual invocation of acpi_bind_one().
When we unload the SSDT overlay we run into the problem. The ACPI
devices are deleted as normal via acpi_device_del_work_fn() and the
acpi_device_del_list.
However, the following warning and stack trace is output as the
deletion does not go smoothly:
------------[ cut here ]------------
kernfs: can not remove 'physical_node', no directory
WARNING: CPU: 1 PID: 11 at fs/kernfs/dir.c:1674 kernfs_remove_by_name_ns+0xb9/0xc0
Modules linked in:
CPU: 1 PID: 11 Comm: kworker/u128:0 Not tainted 6.8.0-rc6+ #1
Hardware name: congatec AG conga-B7E3/conga-B7E3, BIOS 5.13 05/16/2023
Workqueue: kacpi_hotplug acpi_device_del_work_fn
RIP: 0010:kernfs_remove_by_name_ns+0xb9/0xc0
Code: e4 00 48 89 ef e8 07 71 db ff 5b b8 fe ff ff ff 5d 41 5c 41 5d e9 a7 55 e4 00 0f 0b eb a6 48 c7 c7 f0 38 0d 9d e8 97 0a d5 ff <0f> 0b eb dc 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90
RSP: 0018:ffff9f864008fb28 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff8ef90a8d4940 RCX: 0000000000000000
RDX: ffff8f000e267d10 RSI: ffff8f000e25c780 RDI: ffff8f000e25c780
RBP: ffff8ef9186f9870 R08: 0000000000013ffb R09: 00000000ffffbfff
R10: 00000000ffffbfff R11: ffff8f000e0a0000 R12: ffff9f864008fb50
R13: ffff8ef90c93dd60 R14: ffff8ef9010d0958 R15: ffff8ef9186f98c8
FS: 0000000000000000(0000) GS:ffff8f000e240000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f48f5253a08 CR3: 00000003cb82e000 CR4: 00000000003506f0
Call Trace:
<TASK>
? kernfs_remove_by_name_ns+0xb9/0xc0
? __warn+0x7c/0x130
? kernfs_remove_by_name_ns+0xb9/0xc0
? report_bug+0x171/0x1a0
? handle_bug+0x3c/0x70
? exc_invalid_op+0x17/0x70
? asm_exc_invalid_op+0x1a/0x20
? kernfs_remove_by_name_ns+0xb9/0xc0
? kernfs_remove_by_name_ns+0xb9/0xc0
acpi_unbind_one+0x108/0x180
device_del+0x18b/0x490
? srso_return_thunk+0x5/0x5f
? srso_return_thunk+0x5/0x5f
device_unregister+0xd/0x30
i2c_del_adapter.part.0+0x1bf/0x250
i2c_mux_del_adapters+0xa1/0xe0
i2c_device_remove+0x1e/0x80
device_release_driver_internal+0x19a/0x200
bus_remove_device+0xbf/0x100
device_del+0x157/0x490
? __pfx_device_match_fwnode+0x10/0x10
? srso_return_thunk+0x5/0x5f
device_unregister+0xd/0x30
i2c_acpi_notify+0x10f/0x140
notifier_call_chain+0x58/0xd0
blocking_notifier_call_chain+0x3a/0x60
acpi_device_del_work_fn+0x85/0x1d0
process_one_work+0x134/0x2f0
worker_thread+0x2f0/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe3/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2f/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
---[ end trace 0000000000000000 ]---
...
repeated 7 more times, 1 for each channel of the mux
...
The issue is that the binding of the ACPI devices to their peer I2C
adapters is not correctly cleaned up. Digging deeper into the issue we
see that the deletion order is such that the ACPI devices matching the
mux channel i2c adapters are deleted first during the SSDT overlay
removal. For each of the channels we see a call to i2c_acpi_notify()
with ACPI_RECONFIG_DEVICE_REMOVE but, because these devices are not
actually i2c_clients, nothing is done for them.
Later on, after each of the mux channels has been dealt with, we come
to delete the i2c_client representing the PCA9548 device. This is the
call stack we see above, whereby the kernel cleans up the i2c_client
including destruction of the mux and its channel adapters. At this
point we do attempt to unbind from the ACPI peers but those peers no
longer exist and so we hit the kernfs errors.
The fix is to augment i2c_acpi_notify() to handle i2c_adapters. But,
given that the life cycle of the adapters is linked to the i2c_client,
instead of deleting the i2c_adapters during the i2c_acpi_notify(), we
just trigger unbinding of the ACPI device from the adapter device, and
allow the clean up of the adapter to continue in the way it always has.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 525e6fabeae2 ("i2c / ACPI: add support for ACPI reconfigure notifications")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 55750148e5595bb85605e8fbb40b2759c2c4c2d7 ]
If an error occurs after the clk_prepare_enable() call, it should be undone
by a corresponding clk_disable_unprepare() call, as already done in the
remove() function.
As devm_clk_get() is used, we can switch to devm_clk_get_enabled() to
handle it automatically and fix the probe.
Update the remove() function accordingly and remove the now useless
clk_disable_unprepare() call.
Fixes: 0d676a6c4390 ("i2c: add support for Socionext SynQuacer I2C controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2e55b449de7298a751ed0256251019d302af453 ]
The Driver unintentionally programs ctrl reg to clear the fifo, which
happens after the start of transaction. Previously, this was not an issue
as it involved read-modified-write. However, this issue breaks i2c reads
on QEMU, as i2c-read is executed before guest starts programming control
register.
Fixes: ff0cf7bca630 ("i2c: cadence: Remove unnecessary register reads")
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 91811a31b68d3765b3065f4bb6d7d6d84a7cfc9f ]
Baruch reported an OOPS when using the designware controller as target
only. Target-only modes break the assumption of one transfer function
always being available. Fix this by always checking the pointer in
__i2c_transfer.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Closes: https://lore.kernel.org/r/4269631780e5ba789cf1ae391eec1b959def7d99.1712761976.git.baruch@tkos.co.il
Fixes: 4b1acc43331d ("i2c: core changes for slave support")
[wsa: dropped the simplification in core-smbus to avoid theoretical regressions]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c94612a72ac87b0337a0d85b9263266776ed4190 ]
I believe RX FIFO depth define 0 is incorrect on Wangxun 10Gb NIC. It
must be at least 1 since code is able to read received data from the
DW_IC_DATA_CMD register.
For now this define is irrelevant since the txgbe_i2c_dw_xfer_quirk()
doesn't use the rx_fifo_depth member variable of struct dw_i2c_dev but
is needed when converting code into generic polling mode implementation.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ceb013b2d9a2946035de5e1827624edc85ae9484 upstream.
If registering the platform device fails, the lookup table is
removed in the error path. On module removal we would try to
remove the lookup table again. Fix this by setting priv->lookup
only if registering the platform device was successful.
In addition free the memory allocated for the lookup table in
the error path.
Fixes: d308dfbf62ef ("i2c: mux/i801: Switch to use descriptor passing")
Cc: stable@vger.kernel.org
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 87aec499368d488c20292952d6d4be7cb9e49c5e ]
When being a target, NAK from the controller means that all bytes have
been transferred. So, the last byte needs also to be marked as
'processed'. Otherwise index registers of backends may not increase.
Fixes: f7414cd6923f ("i2c: imx: support slave mode for imx I2C driver")
Signed-off-by: Corey Minyard <minyard@acm.org>
Tested-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
[wsa: fixed comment and commit message to properly describe the case]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c1c9d0f6f7f1dbf29db996bd8e166242843a5f21 ]
According to the Intel datasheets, software must reset the block
buffer index twice for block process call transactions: once before
writing the outgoing data to the buffer, and once again before
reading the incoming data from the buffer.
The driver is currently missing the second reset, causing the wrong
portion of the block buffer to be read.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Piotr Zakowski <piotr.zakowski@intel.com>
Closes: https://lore.kernel.org/linux-i2c/20240213120553.7b0ab120@endymion.delvare/
Fixes: 315cd67c9453 ("i2c: i801: Add Block Write-Block Read Process Call support")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f44bff19268517ee98e80e944cad0f04f1db72e3 ]
On powerpc, it is possible to compile test both the new apple (arm) and
old pasemi (powerpc) drivers for the i2c hardware at the same time,
which leads to a warning about linking the same object file twice:
scripts/Makefile.build:244: drivers/i2c/busses/Makefile: i2c-pasemi-core.o is added to multiple modules: i2c-apple i2c-pasemi
Rework the driver to have an explicit helper module, letting Kbuild
take care of whether this should be built-in or a loadable driver.
Fixes: 9bc5f4f660ff ("i2c: pasemi: Split pci driver to its own file")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 83ef106fa732aea8558253641cd98e8a895604d7 ]
For i2c read operation in GSI mode, we are getting timeout
due to malformed TRE basically incorrect TRE sequence
in gpi(drivers/dma/qcom/gpi.c) driver.
I2C driver has geni_i2c_gpi(I2C_WRITE) function which generates GO TRE and
geni_i2c_gpi(I2C_READ)generates DMA TRE. Hence to generate GO TRE before
DMA TRE, we should move geni_i2c_gpi(I2C_WRITE) before
geni_i2c_gpi(I2C_READ) inside the I2C GSI mode transfer function
i.e. geni_i2c_gpi_xfer().
TRE stands for Transfer Ring Element - which is basically an element with
size of 4 words. It contains all information like slave address,
clk divider, dma address value data size etc).
Mainly we have 3 TREs(Config, GO and DMA tre).
- CONFIG TRE : consists of internal register configuration which is
required before start of the transfer.
- DMA TRE : contains DDR/Memory address, called as DMA descriptor.
- GO TRE : contains Transfer directions, slave ID, Delay flags, Length
of the transfer.
I2c driver calls GPI driver API to config each TRE depending on the
protocol.
For read operation tre sequence will be as below which is not aligned
to hardware programming guide.
- CONFIG tre
- DMA tre
- GO tre
As per Qualcomm's internal Hardware Programming Guide, we should configure
TREs in below sequence for any RX only transfer.
- CONFIG tre
- GO tre
- DMA tre
Fixes: d8703554f4de ("i2c: qcom-geni: Add support for GPI DMA")
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # qrb5165-rb5
Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 92a85b7c6262f19c65a1c115cf15f411ba65a57c ]
Rockchip RV1126 is using old style i2c controller, the i2c2
bus uses a non-sequential offset in the grf register for the
mask/value bits for this bus.
This patch fixes i2c2 bus on rv1126 SoCs.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 990489e1042c6c5d6bccf56deca68f8dbeed8180 ]
To properly handle ACK on the bus when transferring more than one
message in polling mode, move the polling handling loop from
s3c24xx_i2c_message_start() to s3c24xx_i2c_doxfer(). This way
i2c_s3c_irq_nextbyte() is always executed till the end, properly
acknowledging the IRQ bits and no recursive calls to
i2c_s3c_irq_nextbyte() are made.
While touching this, also fix finishing transfers in polling mode by
using common code path and always waiting for the bus to become idle
and disabled.
Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d9cf23ed55d7ba3ab26d617a3ae507863674c8f ]
To properly handle read transfers in polling mode, no waiting for the ACK
state is needed as it will never come. Just wait a bit to ensure start
state is on the bus and continue processing next bytes.
Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 19cde9c92b8d3b7ee555d0da3bcb0232d3a784f4 ]
Possible deadlock scenario (on reboot):
rk3x_i2c_xfer_common(polling)
-> rk3x_i2c_wait_xfer_poll()
-> rk3x_i2c_irq(0, i2c);
--> spin_lock(&i2c->lock);
...
<rk3x i2c interrupt>
-> rk3x_i2c_irq(0, i2c);
--> spin_lock(&i2c->lock); (deadlock here)
Store the IRQ number and disable/enable it around the polling transfer.
This patch has been tested on NanoPC-T4.
Signed-off-by: Jensen Huang <jensenhuang@friendlyarm.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a3368e1186e3ce8e38f78cbca019622095b1f331 upstream.
Since commit aa49c90894d0 ("i2c: core: Run atomic i2c xfer when
!preemptible"), the whole reboot/power off sequence on non-preempt kernels
is using atomic i2c xfer, as !preemptible() always results to 1.
During device_shutdown(), the i2c might be used a lot and not all busses
have implemented an atomic xfer handler. This results in a lot of
avoidable noise, like:
[ 12.687169] No atomic I2C transfer handler for 'i2c-0'
[ 12.692313] WARNING: CPU: 6 PID: 275 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x118
...
Fix this by allowing non-atomic xfer when the interrupts are enabled, as
it was before.
Link: https://lore.kernel.org/r/20231222230106.73f030a5@yea
Link: https://lore.kernel.org/r/20240102150350.3180741-1-mwalle@kernel.org
Link: https://lore.kernel.org/linux-i2c/13271b9b-4132-46ef-abf8-2c311967bb46@mailbox.org/
Fixes: aa49c90894d0 ("i2c: core: Run atomic i2c xfer when !preemptible")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Tested-by: Michael Walle <mwalle@kernel.org>
Tested-by: Tor Vic <torvic9@mailbox.org>
[wsa: removed a comment which needs more work, code is ok]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b4cc1cbba5195a4dd497cf2f8f09e7807977d543 ]
Some masters may drive the transfers with low enough latency between
the nak/stop phase of the current command and the start/address phase
of the following command that the interrupts are coalesced by the
time we process them.
Handle the stop conditions before processing SLAVE_MATCH to fix the
complaints that sometimes occur below.
"aspeed-i2c-bus 1e78a040.i2c-bus: irq handled != irq. Expected
0x00000086, but was 0x00000084"
Fixes: f9eb91350bb2 ("i2c: aspeed: added slave support for Aspeed I2C driver")
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 043465b66506e8c647cdd38a2db1f2ee0f369a1b ]
Add missing clk_disable_unprepare() and geni_se_resources_off() in the error
path in geni_i2c_probe().
Fixes: 14d02fbadb5d ("i2c: qcom-geni: add desc struct to prepare support for I2C Master Hub variant")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 382561d16854a747e6df71034da08d20d6013dfe ]
When an I2C device contains a wake IRQ subordinate to a regmap-irq chip,
the regmap-irq code must be able to perform I2C transactions during
suspend_device_irqs() and resume_device_irqs(). Therefore, the bus must
be suspended/resumed during the NOIRQ phase.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f726eaa787e9f9bc858c902d18a09af6bcbfcdaf ]
When running on a many core ARM64 server, errors were
happening in the ISR that looked like corrupted memory. These
corruptions would fix themselves if small delays were inserted
in the ISR. Errors reported by the driver included "i2c_designware
APMC0D0F:00: i2c_dw_xfer_msg: invalid target address" and
"i2c_designware APMC0D0F:00:controller timed out" during
in-band IPMI SSIF stress tests.
The problem was determined to be memory writes in the driver were not
becoming visible to all cores when execution rapidly shifted between
cores, like when a register write immediately triggers an ISR.
Processors with weak memory ordering, like ARM64, make no
guarantees about the order normal memory writes become globally
visible, unless barrier instructions are used to control ordering.
To solve this, regmap accessor functions configured by this driver
were changed to use non-relaxed forms of the low-level register
access functions, which include a barrier on platforms that require
it. This assures memory writes before a controller register access are
visible to all cores. The community concluded defaulting to correct
operation outweighed defaulting to the small performance gains from
using relaxed access functions. Being a low speed device added weight to
this choice of default register access behavior.
Signed-off-by: Jan Bottorff <janb@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f78ca48a8ba9cdec96e8839351e49eec3233b177 upstream.
Currently we set SMBHSTCNT_LAST_BYTE only after the host has started
receiving the last byte. If we get e.g. preempted before setting
SMBHSTCNT_LAST_BYTE, the host may be finished with receiving the byte
before SMBHSTCNT_LAST_BYTE is set.
Therefore change the code to set SMBHSTCNT_LAST_BYTE before writing
SMBHSTSTS_BYTE_DONE for the byte before the last byte. Now the code
is also consistent with what we do in i801_isr_byte_done().
Reported-by: Jean Delvare <jdelvare@suse.com>
Closes: https://lore.kernel.org/linux-i2c/20230828152747.09444625@endymion.delvare/
Cc: stable@vger.kernel.org
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8183fa10c25c7b3c20670bf2b430ddcc1ee03c0 upstream.
During SMBus block data read process, we have seen high interrupt rate
because of TX_EMPTY irq status while waiting for block length byte (the
first data byte after the address phase). The interrupt handler does not
do anything because the internal state is kept as STATUS_WRITE_IN_PROGRESS.
Hence, we should disable TX_EMPTY IRQ until I2C DesignWare receives
first data byte from I2C device, then re-enable it to resume SMBus
transaction.
It takes 0.789 ms for host to receive data length from slave.
Without the patch, i2c_dw_isr() is called 99 times by TX_EMPTY interrupt.
And it is none after applying the patch.
Cc: stable@vger.kernel.org
Co-developed-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b211c7671212cad0b83603c674838c7e824d845 upstream.
This reverts commit 0b01392c18b9993a584f36ace1d61118772ad0ca.
Conversion of PXA to generic I2C recovery, makes the I2C bus completely
lock up if recovery pinctrl is present in the DT and I2C recovery is
enabled.
So, until the generic I2C recovery can also work with PXA lets revert
to have working I2C and I2C recovery again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: stable@vger.kernel.org # 5.11+
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa49c90894d06e18a1ee7c095edbd2f37c232d02 upstream.
Since bae1d3a05a8b, i2c transfers are non-atomic if preemption is
disabled. However, non-atomic i2c transfers require preemption (e.g. in
wait_for_completion() while waiting for the DMA).
panic() calls preempt_disable_notrace() before calling
emergency_restart(). Therefore, if an i2c device is used for the
restart, the xfer should be atomic. This avoids warnings like:
[ 12.667612] WARNING: CPU: 1 PID: 1 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch+0x33c/0x6b0
[ 12.676926] Voluntary context switch within RCU read-side critical section!
...
[ 12.742376] schedule_timeout from wait_for_completion_timeout+0x90/0x114
[ 12.749179] wait_for_completion_timeout from tegra_i2c_wait_completion+0x40/0x70
...
[ 12.994527] atomic_notifier_call_chain from machine_restart+0x34/0x58
[ 13.001050] machine_restart from panic+0x2a8/0x32c
Use !preemptible() instead, which is basically the same check as
pre-v5.2.
Fixes: bae1d3a05a8b ("i2c: core: remove use of in_atomic()")
Cc: stable@vger.kernel.org # v5.2+
Suggested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://lore.kernel.org/r/20230327-tegra-pmic-reboot-v7-2-18699d5dcd76@skidata.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cc9c54232f04aef3a5d7f64a0ece7df00f1aaa3d ]
i2c-dev.c utilizes memdup_user() to copy a userspace array. This is done
without an overflow check.
Use the new wrapper memdup_array_user() to copy the array more safely.
Suggested-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5ac61d26b8baff5b2e5a9f3dc1ef63297e4b53e7 ]
Make sure we don't OOPS in case clock-frequency is set to 0 in a DT. The
variable set here is later used as a divisor.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6af79f7fe748fe6a3c5c3a63d7f35981a82c2769 ]
Yang Yingliang reported a memleak:
===
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff888014aec078 (size 8):
comm "xrun", pid 356, jiffies 4294910619 (age 16.332s)
hex dump (first 8 bytes):
31 2d 30 30 31 63 00 00 1-001c..
backtrace:
[<00000000eb56c0a9>] __kmalloc_track_caller+0x1a6/0x300
[<000000000b220ea3>] kvasprintf+0xad/0x140
[<00000000b83203e5>] kvasprintf_const+0x62/0x190
[<000000002a5eab37>] kobject_set_name_vargs+0x56/0x140
[<00000000300ac279>] dev_set_name+0xb0/0xe0
[<00000000b66ebd6f>] i2c_new_client_device+0x7e4/0x9a0
If device_register() returns error in i2c_new_client_device(),
the name allocated by i2c_dev_set_name() need be freed. As
comment of device_register() says, it should use put_device()
to give up the reference in the error path.
===
I think this solution is less intrusive and more robust than he
originally proposed solutions, though.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Closes: http://patchwork.ozlabs.org/project/linux-i2c/patch/20221124085448.3620240-1-yangyingliang@huawei.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c56f9ef25a33e51f09a448d25cf863b61c9658d ]
Add SMBus PCI ID on Intel Birch Stream SoC.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ba15a14399c262f91ce30c19fcbdc952262dd1be ]
Add the code to handle an invalid state when both bits S_RX_EVENT
(indicating a transaction) and S_START_BUSY (indicating the end
of transaction - transition of START_BUSY from 1 to 0) are set in
the interrupt status register during a slave read.
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Fixes: 1ca1b4516088 ("i2c: iproc: handle Master aborted error")
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
In case of SMBUS byte read with PEC enabled, the whole transfer
is split into two commands. A first write command, followed by
a read command. The write command does not have any PEC byte
and a PEC byte is appended at the end of the read command.
(cf Read byte protocol with PEC in SMBUS specification)
Within the STM32 I2C controller, handling (either sending
or receiving) of the PEC byte is done via the PECBYTE bit in
register CR2.
Currently, the PECBYTE is set at the beginning of a transfer,
which lead to sending a PEC byte at the end of the write command
(hence losing the real last byte), and also does not check the
PEC byte received during the read command.
This patch corrects the function stm32f7_i2c_smbus_xfer_msg
in order to only set the PECBYTE during the read command.
Fixes: 9e48155f6bfe ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
i2c-mux-gpmux uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: ac8498f0ce53 ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
i2c-demux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: 50a5ba876908 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
i2c-mux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: c4aee3e1b0de ("i2c: mux: pinctrl: remove platform_data")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When the `CONFIG_I2C_SLAVE` option is enabled and the device operates
as a slave, a situation arises where the master sends a START signal
without the accompanying STOP signal. This action results in a
persistent I2C bus timeout. The core issue stems from the fact that
the i2c controller remains in a slave read state without a timeout
mechanism. As a consequence, the bus perpetually experiences timeouts.
In this case, the i2c bus will be reset, but the slave_state reset is
missing.
Fixes: fee465150b45 ("i2c: aspeed: Reset the i2c controller when timeout occurs")
Signed-off-by: Jian Zhang <zhangjian.3032@bytedance.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Sometimes, our completions race with new master transfers and override
the bus->operation and bus->master_or_slave variables. This causes
transactions to timeout and kernel crashes less frequently.
To remedy this, we re-order all completions to the very end of the
function.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: William A. Kennington III <william@wkennington.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
I2C_CLASS_DEPRECATED is a flag and not an actual class.
There's nothing speaking against both, parent and child, having
I2C_CLASS_DEPRECATED set. Therefore exclude it from the check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The error paths for xiic_reinit() return negative values on failure
and 0 on success - this error message therefore is triggered on
_success_ rather than failure. Correct the condition so it's only
shown on failure as intended.
Fixes: 8fa9c9388053 ("i2c: xiic: return value of xiic_reinit")
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In i2c_mux_gpio_probe_fw(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 98b2b712bc85 ("i2c: i2c-mux-gpio: Enable this driver in ACPI land")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
devm_kstrdup() returns pointer to allocated string on success,
NULL on failure. So it is better to check the return value of it.
Fixes: e35478eac030 ("i2c: mux: demux-pinctrl: run properly with multiple instances")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The DesignWare IP can be synthesized with the IC_EMPTYFIFO_HOLD_MASTER_EN
parameter.
In this case, when the TX FIFO gets empty and the last command didn't have
the STOP bit (IC_DATA_CMD[9]), the controller will hold SCL low until
a new command is pushed into the TX FIFO or the transfer is aborted.
When the controller is holding SCL low, it cannot be disabled.
The transfer must first be aborted.
Also, the bus recovery won't work because SCL is held low by the master.
Check if the master is holding SCL low in __i2c_dw_disable() before trying
to disable the controller. If SCL is held low, an abort is initiated.
When the abort is done, then proceed with disabling the controller.
This whole situation can happen for instance during SMBus read data block
if the slave just responds with "byte count == 0".
This puts the driver in an unrecoverable state, because the controller is
holding SCL low and the current __i2c_dw_disable() procedure is not
working. In this situation only a SoC reset can fix the i2c bus.
Co-developed-by: Jonathan Borne <jborne@kalray.eu>
Signed-off-by: Jonathan Borne <jborne@kalray.eu>
Signed-off-by: Yann Sionneau <ysionneau@kalray.eu>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
We have to unregister tco_pdev also if i2c_add_adapter() fails.
Fixes: 9424693035a5 ("i2c: i801: Create iTCO device on newer Intel PCHs")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This fixes the below warnings
drivers/i2c/busses/i2c-cadence.c:221: warning: Function parameter or
member 'rinfo' not described in 'cdns_i2c'
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308171510.bKHBcZQW-lkp@intel.com/
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Reset the i2c controller when an i2c transfer timeout occurs.
The remaining interrupts and device should be reset to avoid
unpredictable controller behavior.
Fixes: 2e57b7cebb98 ("i2c: aspeed: Add multi-master use case support")
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The "i2c_mlxcpld" platform device is only instantiated on X86 systems
(through drivers/platform/x86/mlx-platform.c), or on ARM64 systems with
ACPI (through drivers/platform/mellanox/nvsw-sn2201.c). Hence further
restrict the dependency on ARM64 to ACPI, to prevent asking the user
about this driver when configuring an ARM64 kernel without ACPI support.
While at it, document in the Kconfig help text that the driver supports
ARM64/ACPI based systems, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
I2C Address Translator (ATR) support is not a stand-alone driver, but a
library. All of its users select I2C_ATR. Hence there is no need for
the user to enable this symbol manually, except when compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has mainly cleanups this time and a few driver improvements.
Because a lot of developers were on holidays (including myself) it was
a good timing to apply lots of cleanups which would normally cause
merge conflicts with other floating patches. Extra thanks go to Andi
Shyti who backed me up when I was on a four week hiatus. This is also
the reason that some patches were commited later than ideal"
* tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (67 commits)
i2c: at91: Use dev_err_probe() instead of dev_err()
I2C: ali15x3: Do PCI error checks on own line
i2c: Make return value check more accurate and explicit for devm_pinctrl_get()
i2c: designware: Add support for recovery when GPIO need pinctrl
i2c: mlxcpld: Add support for extended transaction length
i2c: mlxcpld: Allow driver to run on ARM64 architecture
i2c: nforce2: Do PCI error check on own line
i2c: sis5595: Do PCI error checks on own line
i2c: qcom-cci: Fix error checking in cci_probe()
i2c: muxes: pca954x: Add regulator support
i2c: muxes: pca954x: Add MAX735x/MAX736x support
dt-bindings: i2c: Add Maxim MAX735x/MAX736x variants
dt-bindings: i2c: pca954x: Correct interrupt support
i2c: pnx: Use devm_platform_get_and_ioremap_resource()
i2c: pxa: Use devm_platform_get_and_ioremap_resource()
i2c: s3c2410: Use devm_platform_get_and_ioremap_resource()
i2c: sh_mobile: Use devm_platform_get_and_ioremap_resource()
i2c: st: Use devm_platform_get_and_ioremap_resource()
i2c: qcom-geni: Convert to devm_platform_ioremap_resource()
i2c: stm32f4: Use devm_platform_get_and_ioremap_resource()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new i2c drivers: ds90ub913, ds90ub953, ds90ub960, dw9719, ds90ub913
- new Intel IVSC MEI drivers
- some Mediatek platform drivers were moved to a common location
- Intel atomisp2 driver is now working with the main ov2680 driver. Due
to that, the atomisp2 ov2680 staging one was removed
- the bttv driver was finally converted to videobuf2 framework. This
was the last one upstream using videobuf version 1 core. We'll likely
remove the old videobuf framework on 6.7
- lots of improvements at atomisp driver: it now works with normal I2C
sensors. Several compile-mode dependecies to select between ISP2400
and ISP2401 are now solved in runtime
- a new ipu-bridge logic was added to work with IVSC MEI drivers
- venus driver gained better support for new VPU versions
- the v4l core async framework has gained lots of improvements and
cleanups
- lots of other cleanups, improvements and driver fixes
* tag 'media/v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (358 commits)
media: ivsc: Add ACPI dependency
media: bttv: convert to vb2
media: bttv: use audio defaults for winfast2000
media: bttv: refactor bttv_set_dma()
media: bttv: move vbi_skip/vbi_count out of buffer
media: bttv: remove crop info from bttv_buffer
media: bttv: remove tvnorm field from bttv_buffer
media: bttv: remove format field from bttv_buffer
media: bttv: move do_crop flag out of bttv_fh
media: bttv: copy vbi_fmt from bttv_fh
media: bttv: copy vid fmt/width/height from fh
media: bttv: radio use v4l2_fh instead of bttv_fh
media: bttv: replace BUG with WARN_ON
media: bttv: use video_drvdata to get bttv
media: i2c: rdacm21: Fix uninitialized value
media: coda: Remove duplicated include
media: vivid: fix the racy dev->radio_tx_rds_owner
media: i2c: ccs: Check rules is non-NULL
media: i2c: ds90ub960: Fix PLL config for 1200 MHz CSI rate
media: i2c: ds90ub953: Fix use of uninitialized variables
...
|
|
Change
if (IS_ERR(x)) { dev_err(...); return PTR_ERR(x); }
into
return dev_err_probe()
Also, return the correct error instead of hardcoding -ENODEV
This change has also the advantage of handling the -EPROBE_DEFER situation.
Signed-off-by: Yann Sionneau <yann@sionneau.net>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
