| Age | Commit message (Collapse) | Author |
|---|
|
Pass the to-be-limited register to alert functions and use it to determine
conversion from limit to register value.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Convert driver to use the with_info hardware monitoring API
to reduce its dependency on sysfs attribute functions.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
ina2xx_get_value() will be needed earlier in the next patch, so move it.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Alerts should only be cleared after reported, not immediately after the
alert condition has been cleared. Set the latch enable bit to keep alerts
latched until the alert register has been read from the chip.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Move all chip initialization code into a single function.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Module tests show various overflow problems when writing limits
and other attributes.
in0_crit: Suspected overflow: [max=82, read 0, written 2147483648]
in0_lcrit: Suspected overflow: [max=82, read 0, written 2147483648]
in1_crit: Suspected overflow: [max=40959, read 0, written 2147483647]
in1_lcrit: Suspected overflow: [max=40959, read 0, written 2147483647]
power1_crit: Suspected overflow: [max=134218750, read 0, written 2147483648]
update_interval: Suspected overflow: [max=2253, read 2, written 2147483647]
Implement missing clamping on attribute write operations to avoid those
problems.
While at it, check in the probe function if the shunt resistor value
passed from devicetree is valid, and bail out if it isn't. Also limit
mutex use to the code calling ina2xx_set_shunt() since it isn't needed
when called from the probe function.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
If it is necessary to re-initialize the chip, for example because
it has been power cycled, use regmap functions to update register
contents. This ensures that all registers, including the configuration
register and alert registers, are updated to previously configured
values without having to locally cache everything.
For this to work, volatile registers have to be marked as volatile.
Also, the cache needs to be bypassed when reading the calibration
and mask_enable registers. While the calibration register is not
volatile, it will be reset to 0 if the chip has been power cycled.
Most of the bits in the mask_enable register are configuration bits,
except for bit 4 which reports if an alert has been observed.
Both registers need to be marked as non-volatile to be updated
after a power cycle, but it is necessary to bypass the cache when
reading them to detect if the chip has been power cycled and to
read the alert status.
The chip does not support register auto-increments. It is therefore
necessary to configure regmap to use single register read/write
operations. Otherwise regmap tries to write all registers in a single
operation when synchronizing register contents with the hardware,
and the synchronization fails.
Another necessary change is to declare ina226_alert_to_reg() as u16.
So far it returned an s16 which is sign extended to a large negative
value which is then sent to regmap as unsigned int, causing an -EINVAL
error return.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
If regmap is accessed more than once in a function, declare and used
local regmap variable.
While at it, drop low value debug messages.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Recent versions of checkpatch complain that struct regmap_config
should be declared as const.
WARNING: struct regmap_config should normally be const
Doing so reveals a potential problem in the driver: If both supported
chips are present in a single system, the maximum number of registers
may race when devices are instantiated since max_registers is updated
in the probe function. Solve the problem by setting .max_registers to the
maximum register address of all supported chips. This does not make a
practical difference while fixing the potential race condition and reducing
code complexity.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use bit operations where possible to make the code more generic and to
align it with other drivers. Also use compile time conversion from bit
to mask to reduce runtime overhead.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
There are no in-tree users of ina2xx platform data. Drop it and support
device properties instead as alternative if it should ever be needed.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Simplify driver maintenance by reordering include files to alphabetic
order.
Whule at it, drop unnecessary / unused jiffies.h.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
clang warns (or errors due to CONFIG_WERROR):
drivers/hwmon/oxp-sensors.c:481:3: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
drivers/hwmon/oxp-sensors.c:553:3: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
drivers/hwmon/oxp-sensors.c:556:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
drivers/hwmon/oxp-sensors.c:607:3: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return. Add the missing breaks to
silence the warnings.
Fixes: b82b38a49926 ("hwmon: (oxp-sensors) Add support for multiple new devices.")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Message-ID: <20240828-hwmon-oxp-sensors-fix-clang-implicit-fallthrough-v1-1-dc48496ac67a@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The pwm1_enable attribute of the pwmfan driver influences the mode of
operation, especially in case of a requested pwm1 duty cycle of zero.
Especially setting pwm1_enable to two, should keep the pwm controller
enabled even if the duty cycle is set to zero [1].
This is not the case at the moment, as the pwm controller is disabled
always if pwm1 is set to zero.
This commit tries to fix this behavior.
[1] https://docs.kernel.org/hwmon/pwm-fan.html
Signed-off-by: Johannes Kirchmair <johannes.kirchmair@skidata.com>
Message-ID: <20240827054454.521494-1-mailinglist1@johanneskirchmair.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use the min() macro to simplify the pc87360_init_device() function
and improve its readability.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Message-ID: <20240827070442.40667-1-shenlichuan@vivo.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
SG2042 use an external MCU to provide basic hardware information
and thermal sensors.
Add driver support for the onboard MCU of SG2042.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Message-ID: <IA1PR20MB49536C786048D1E676BB9C20BB822@IA1PR20MB4953.namprd20.prod.outlook.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use scoped for_each_child_of_node_scoped() when iterating over device
nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Message-ID: <20240822062956.3490387-9-ruanjinjie@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use scoped for_each_child_of_node_scoped() when iterating over device
nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Message-ID: <20240822062956.3490387-8-ruanjinjie@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use scoped for_each_child_of_node_scoped() when iterating over device
nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Message-ID: <20240822062956.3490387-7-ruanjinjie@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use scoped for_each_child_of_node_scoped() when iterating over device
nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Message-ID: <20240822062956.3490387-6-ruanjinjie@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use scoped for_each_child_of_node_scoped() when iterating over device
nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Message-ID: <20240822062956.3490387-5-ruanjinjie@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use scoped for_each_child_of_node_scoped() when iterating over device
nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Message-ID: <20240822062956.3490387-4-ruanjinjie@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use scoped for_each_child_of_node_scoped() when iterating over device
nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Message-ID: <20240822062956.3490387-3-ruanjinjie@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use scoped for_each_child_of_node_scoped() when iterating over device
nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Message-ID: <20240822062956.3490387-2-ruanjinjie@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This removes some boilerplate from the code and will allow adding
future CPUs by just device IDs.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Message-ID: <20240820053558.1052853-1-superm1@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the OrangePi NEO-01. It uses different registers for PWM
manual mode, set PWM, and read fan speed than previous devices. Valid PWM
input and duty cycle is 1-244, we scale this from 1-255 to maintain
compatibility with the existing interface.
Add OneXPlayer 2 series, OneXFly, and X1 series models. The 2/X1 series use
new registers for turbo button takeover and read fan speed. X1 has an Intel
variant so change the CPU detection at init to only check for the affected
devices. While at it, adjust formatting of some constants and reorder all
cases alphabetically for consistency. Rename OXP_OLD constants to OXP_MINI
for disambiguation. Update code comments for clarity.
Add support for AYANEO models 2S, AIR 1S, Flip series, GEEK 1S, and KUN.
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Tested-by: Kevin Greenberg <kdgreenberg234@protonmail.com>
Tested-by: Joshua Tam <csinaction@pm.me>
Tested-by: Parth Menon <parthasarathymenon@gmail.com>
Tested-by: Philip Müller <philm@manjaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202408160329.TLNbIwRC-lkp@intel.com/
Message-ID: <20240822183525.27289-2-derekjohn.clark@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The documented compatible string is "st,stts751", not "stts751". Even if
"stts751" was in use, there's no need to list "stts751" in the DT match
table. The I2C core will strip any vendor prefix and match against the
i2c_device_id table which has an "stts751" entry.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Message-ID: <20240826191811.1416011-1-robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Fixes: 9e8269de100d ("hwmon: (ntc_thermistor) Add DT with IIO support to NTC thermistor driver")
Signed-off-by: Yuntao Liu <liuyuntao12@huawei.com>
Message-ID: <20240815083021.756134-1-liuyuntao12@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit 2be5f0d75325 ("hwmon: (sch56xx) Use devres functions for watchdog")
removed the implementation but leave declaration.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Message-ID: <20240816095740.877729-1-yuehaibing@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Message-ID: <20240814024555.3875387-1-liaochen4@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Some of the newer Microsoft Surface devices (such as the Surface Book
3 and Pro 9) have thermal sensors connected via the Surface Aggregator
Module (the embedded controller on those devices). Add a basic driver
to read out the temperature values of those sensors.
The EC can have up to 16 thermal sensors connected via a single
sub-device, each providing temperature readings and a label string.
Link: https://github.com/linux-surface/surface-aggregator-module/issues/59
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Co-developed-by: Ivor Wanders <ivor@iwanders.net>
Signed-off-by: Ivor Wanders <ivor@iwanders.net>
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Message-ID: <20240811001503.753728-1-luzmaximilian@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Boards G15CF has got a nct6775 chip, but by default there's no use of it
because of resource conflict with WMI method.
Add the board to the WMI monitoring list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Tested-by: Attila <attila@fulop.one>
Message-ID: <20240812152652.1303-1-pauk.denis@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
There is no need to actively disable a regulator that has not been
enabled by the driver, which makes the call to cc2_disable() in the
probe function meaningless, because the probe function never enables
the device's dedicated regulator.
Once the call to cc2_disable() is dropped, the error paths can directly
return dev_err_probe() in all cases.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20240813-chipcap2-probe-improvements-v2-1-e9a2932a8a00@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Update datasheet references. Replace misleading 'force parameter needed'
with 'must be instantiated explicitly'. Explain the reason for the missing
auto-detection. Mention all supported chips in Kconfig.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Convert driver to with_info hwmon API to simplify the code and
to reduce its size.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use regmap for local caching and for multi-byte operations to be able
to use regmap API functions and to reduce the need for locking in the
driver.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The chip IDs are not used by the driver. Drop them. Use driver data to
store the limit register resolution instead, and use this information
when writing temperature limits to improve chip specific rounding and
to avoid writing into unused register bits.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Simplify driver maintenance by reordering files to alphabetic order.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Checking three configuration register bits and the manufacturer ID
register to auto-detect LM92 is a bit vague. Repeat twice on replicated
register addresses to improve detection accuracy. Check the manufacturer
ID first and bail out immediately without reading the other register if
there is a mismatch to reduce the number of i2c transfers needed in that
case. Also explicitly test for an error from reading the configuration
register to avoid potential situations where the returned error masked
against 0xe0 is 0.
While at it, drop "lm92: Found National Semiconductor LM92 chip" detection
noise.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use of_property_present() to test for property presence rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20240731191312.1710417-13-robh@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The temperature reading function was using a signed long for the ADC
code, which could lead to mishandling of invalid codes on 32-bit
platforms. This allowed out-of-range ADC codes to be incorrectly
interpreted as valid values and used in temperature calculations.
Change adc_code to u32 to ensure that invalid ADC codes are correctly
identified on all platforms.
Fixes: 1b2ca93cd059 ("hwmon: Add driver for Astera Labs PT5161L retimer")
Signed-off-by: Cosmo Chou <chou.cosmo@gmail.com>
Message-ID: <20240819104630.2375441-1-chou.cosmo@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
X570-E GAMING does not have VRM temperature sensor.
Signed-off-by: Ross Brown <true.robot.ross@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20240730062320.5188-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Bail out immediately if reading any of the registers used for chip
detection fails, or if it returns an unexpected value. Drop all log
messages from detection code.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The chip supports reading and writing the conversion rate.
Add support for the update_interval sysfs attribute.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Convert driver to with_info hwmon API to simplify the code and
with it its maintainability.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use regmap for local caching, to hide register read/write address
differences, and for multi-byte operations. With this change,
the driver specific lock is no longer necessary.
While at it, check errors seen when initializing the chip and bail out
if chip initialization fails.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Bit 0, 5, and 6 in the status register are reserved and, if set, do not
indicate an alarm. Bit 7 is the 'busy' bit and also does not indicate
an alarm. Mask the non-alarm bits to avoid reporting them to userspace.
Cc: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Simplify maintenance by reordering include files to alphabetic order.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Module test code reports underflows when writing sensor limits.
temp2_min: Suspected underflow: [min=-77000, read 101000, written -2147483648]
temp2_max: Suspected underflow: [min=-77000, read 101000, written -2147483648]
temp2_crit: Suspected underflow: [min=-77000, read 101000, written -2147483648]
Clamp temperature ranges when writing limits to fix the problem.
While at it, use sign_extend32() when reading temperatures to make
the code easier to understand.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In the MAX6581 datasheet Revision 0 to 3, the local channel overtemperature
status is reported in bit 6 of register 0x45, and the overtemperature
status for remote channel 7 is reported in bit 7. In Revision 4 and later,
the local channel overtemperature status is reported in bit 7, and the
remote channel 7 overtemperature status is reported in bit 6. A real
chip was found to match the functionality documented in Revision 4 and
later.
The code was fixed with commit 1ea3fd1eb986 ("hwmon: (max6697) Fix swapped
temp{1,8} critical alarms"). At that time it looked like this was an
original bug. It only turned out later that the problem was the result of
incorrect information in the chip datasheet.
Document the discrepancy to avoid confusion caused by old versions of the
datasheet.
Cc: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
