| Age | Commit message (Collapse) | Author |
|---|
|
The macro timed_wait_for() in utils.h isn't used in current ipc
driver, so remove it for avoiding confusion.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
And as such should be marked static to avoid global namespace pollution.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This adds support for the THQ uDraw tablet for the PS3, as
4 separate device nodes, so that user-space can easily consume
events coming from the hardware.
Note that the touchpad two-finger support is fairly unreliable,
and a right-click can only be achieved with a two-finger tap
with the two fingers slightly apart (about 1cm should be enough).
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The eraser end of the 8K pen available for the MobileStudio Pro has a tool
ID of 0x84a. The 'wacom_intuos_get_tool_type' function does not currently
recognize this ID, causing it to return BTN_TOOL_PEN rather than
BTN_TOOL_RUBBER. This does not cause a problem for the MobileStudio Pro
since, as a HID_GENERIC device, the driver relies on the state of the
HID_DG_INVERT usage instead. It would, however, cause problems if the pen
is used with devices that use the traditional 'wacom_intuos_irq' codepath
instead.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This is trying to clear the lower 32 bits but the type is wrong so it
clears everything.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Certain devices produced by Weida Tech need to have a wakeup command sent to
them before powering on. The call itself will come back with error, but the
device can be powered on afterwards.
[jkosina@suse.cz: rewrite changelog]
[jkosina@suse.cz: remove unused device ID addition]
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
ts_format.reserved is not used anywhere yet, but the compiler generates a
warning when the struct's (uninitialized) field is being copied around
drivers/hid/intel-ish-hid/ipc/ipc.c: In function ‘write_ipc_from_queue’:
drivers/hid/intel-ish-hid/ipc/ipc.c:316: warning: ‘ts_format.reserved’ may be used uninitialized in this function
Avoid this by force-initializing the field to zero.
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
User is unable to access to input-X-yyy and feature-X-yyy where
X is a hex value and more than 9 (e.g. input-a-yyy, feature-b-yyy) in HID
sensor custom sysfs interface.
This is because when creating the attribute, the attribute index is
written to using %x (hex). However, when reading and writing values into
the attribute, the attribute index is scanned using %d (decimal). Hence,
user is unable to access to attributes with index in hex values
(e.g. 'a', 'b', 'c') but able to access to attributes with index in
decimal values (e.g. 1, 2, 3,..).
This fix will change input-%d-%x-%s and feature-%d-%x-%s to input-%x-%x-%s
and feature-%x-%x-%s in show_values() and store_values() accordingly.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
On some platforms ISH interrupt is shared, which causes request_irq to
fail. This requires IRQF_SHARED irq flag.
But IRQF_NO_SUSPEND and IRQF_SHARED should not be used together, so
removed IRQF_NO_SUSPEND flag. Anyway this driver doesn't require
IRQF_NO_SUSPEND, as this interrupt is not required during "noirq" phases
of suspending and resuming devices as well as during the time when
nonboot CPUs are taken offline and brought back online.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When built as a module, modprobe followed by rmmod can fail because
DMA was still active. So to fix this, DMA needs to be disabled during
module exit.
This change disables DMA during modules exit and change the ISH PCI
device status to D3.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add a new function ish_disable_dma() and move DMA disable operations
here, so that this functionality can be reused.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Same operations are done in ish_hw_start() and _ish_hw_reset() to
wakeup ISH device. Consolidate them by introducing a new function
ish_wakeup() and move the code there.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add a new module named hid-mf that implements force feedback for game
controller adapters manufactured by Mayflash. Currently only the PS3 adapter is
supported, other adapters still need to be tested.
Signed-off-by: Marcel Hasler <mahasler@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
All known gamepad adapters by Mayflash (identified as Dragonrise) need
HID_QUIRK_MULTI_INPUT to split them up into four input devices. Without this
quirk those adapters are falsely recognized as tablets. Fixes bug 115841
(https://bugzilla.kernel.org/show_bug.cgi?id=115841).
Signed-off-by: Marcel Hasler <mahasler@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Like many similar devices it needs a quirk to work.
Issuing the request gets the device into an irrecoverable state.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fix
drivers/hid/intel-ish-hid/ipc/pci-ish.c:247:12: warning: ‘ish_suspend’ defined but not used [-Wunused-function]
static int ish_suspend(struct device *device)
^
drivers/hid/intel-ish-hid/ipc/pci-ish.c:282:12: warning: ‘ish_resume’ defined but not used [-Wunused-function]
static int ish_resume(struct device *device)
^
by sticking them in the CONFIG_PM range too.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-input@vger.kernel.org
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When report count is more than one and report size is not 4 bytes, then we
need some packing into result buffer from the caller of function
sensor_hub_get_feature.
By default the value extracted from a field is 4 bytes from hid core
(using hid_hw_request(hsdev->hdev, report, HID_REQ_GET_REPORT)), even
if report size if less than 4 byte. So when we copy data to user buffer in
sensor_hub_get_feature, we need to only copy report size bytes even
when report count is more than 1. This is
not an issue for most of the sensor hub fields as report count will be 1
where we already copy only report size bytes, but some string fields
like description, it is a problem as the report count will be more than 1.
For example:
Field(6)
Physical(Sensor.OtherCustom)
Application(Sensor.Sensor)
Usage(11)
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Report Size(16)
Report Count(11)
Here since the report size is 2 bytes, we will have 2 additional bytes of
0s copied into user buffer, if we directly copy to user buffer from
report->field[]->value
This change will copy report size bytes into the buffer of caller for each
usage report->field[]->value. So for example without this change, the
data displayed for a custom sensor field "sensor-model":
76 00 101 00 110 00 111 00 118 00 111
(truncated to report count of 11)
With change
76 101 110 111 118 111 32 89 111 103 97
("Lenovo Yoga" in ASCII )
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The "Steering" usage (HID_UP_SIMULATION | 0xc8) is defined in HUT 1.12 as
follows:
"A steering wheel is a single degree-of-freedom device that rotates about
an axis. The zero position is always the neutral or 'straight ahead'
position, with positive values turning clockwise and negative values
turning counterclockwise. If the Coordinate Values Wrap attribute is
set, the steering wheel can be turned past 360 degrees."
The hidinput_configure_usage function canonically maps this usage to the
ABS_WHEEL axis, but hidinput_calc_abs_res does not recognize this axis
as one for which it can calculate a resolution. This effectively prevents
wheels from being assigned a proper resolution that userspace can use
to determine the precise angle of input.
This commit adds ABS_WHEEL as a rotational axis to hidinput_calc_abs_res.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The HID specification that the MobileStudio Pro follows includes usages
for several values that would be good to support so that future devices
"just work" out of the box. Extend the HID_GENERIC pad codepath to handle
these usages.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Adds support for usages that may appear on the pen or pad interface which
report the state of the tablet battery.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
As with usages for the pen, the Custom HID specificiation includes
usages for the pad. Here we add functions to map and handle most
of the pad usages present on the MobileStudio Pro.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Many of Wacom's display tablets include an "outbound" area where pen
digitizing is possible but outside of the display area. To accommodate
such sensors in the HID_GENERIC codepath, we add support for the
necessary vendor-defined HID feature usages and adjust the min/max
values of the X and Y axes accordingly, similar to what is done in
the non-generic codepath.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Many of Wacom's display tablets include an "outbound" area where pen
digitizing is possible but outside of the display area. To ensure that
pen coordinates are mapped to the correct on-screen location, the driver
sets the minimum and maximum axis values of X and Y to those coordinates
which coincide with the screen edge. These values are simply the
hardware minimum/maximum plus/minus the outbound size for a particular
edge.
When outbound support was added/updated in ac414da, fa77034, and
ecd618d, we decided to have the wacom_features structs store the desired
minimum and maximum values directly. In hindsight, this was perhaps not
the best choice since it has allowed minor errors to crop up unnoticed.
Some tablets have had their coordinates over-corrected (e.g. most of the
devices "fixed" in ecd618d were already adjusted in ac414da), while
others never had a correction applied (e.g. the ISDv5 325, whose
declared maximum the hardware maximum instead of the outbound maximum).
A less error-prone method of handling the outbound is to let the driver
calculate the correct minimum/maximum values by providing it with both
the actual hardware maximums and the size of the outbound on each edge.
These values are more easy to verify as correct since the values can be
trivially compared against specifications.
This patch reverts the declared maximum values to the actual hardware
maximums, e.g. as declared prior to ac414da (values for these and other
display tablets that were subsuquently introduced have been verified
against specs). Per-edge outbound sizes are stored in the wacom_features
struct as offset_{left,right,top,bottom} and used in combination with
the hardware ranges to calculate effective axis ranges for ABS_X and
ABS_Y.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Devices following the new Custom HID mode specification (as well as even
some recent component sensors which use the same standard HID usage)
are capable of reporting tool ID information that we need to relay to
userspace. This patch adds support for reading and relaying the tool
type information, which is (unfortunately) split across two usages.
We also advertise the existence of tool types beyond BTN_TOOL_PEN
that might be available.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The 'wacom_intuos_inout' function incorrectly assmebles tool IDs from the
proximity report, shifting the higher values of the ID four bits farther
than intended. This problem was not detected until too late, but has not
caused any issues since the incorrect IDs still fit in a 32-bit integer
and userspace programs have not required the value to match the hardware
(just that the values are unique and constant).
The tool IDs reported by the new MobileStudio Pro (or any future
HID_GENERIC device that supports them) do not suffer from the same
assembly issue, however. In order for 'wacom_intuos_get_tool_type' to
work for with both codepaths, we correct this issue internally and
have 'wacom_intuos_general' only mangle the ID when it is posted to
userspace.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Wacom's professional tablets beginning with the Intuos4 are capable of
reporting an intermediate degree of proximity where the pen is no longer
close enough to communicate with ("in prox"), but still close enough to
be sensed ("in range"). This additional state is particularly useful for
performing palm rejection as it allows the driver to disable the touch
sensor while the pen is a greater distance from the tablet.
Like other professional tablets, the new MobileStudio Pro also reports
this intermeidate "in range" proximity state. Its descriptor assigns
usage 0xff0d0036 to this bit. Normally 'wacom_equivalent_usage' would
translate this to the standard HID "Quality" usage, but since this has
a different meaning we have it explicitly ignore the usage and define
it ourselves as "Sense" (since "In Range" is already defined by the
HID standard and interpreted by our driver as meaning "in prox").
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The airbrush fingerwheel does not have a usage that corresponds cleanly
with a standard HID usage, so we add explicit support for it via its
vendor-defined usage.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The vendor-defined 0xFF0D01032 ("Distance") usage is nearly equivalent to
HID_GD_Z, except that the axis direction is inverted. Unlike HID_GD_Z which
increases in value as the pen-to-surface distance is decreased, this usage
decreases. Treat this usage as a special case to ensure we don't invert the
scale to be ABS_DISTANCE compatible like we do for HID_GD_Z.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Wacom's new "MobileStudio Pro" tablets are the first devices in their
branded product line-up to include a usable HID descriptor for the pen
interface. Like prior branded products, the device can operate in one
of two modes: 'Standard HID', and 'Wacom Custom HID'. Although the
first mode is usable by the HID_GENERIC codepath as-is (huzzah!), it is
subject to some restrictions -- most notably pressure being limited
to 2048 levels instead of 8192. To ensure tablets that include support
for Custom HID mode work optimally, we add support for its usages and
switch the device to Custom HID mode if possible.
The usages defined for Custom HID mode are often numerically similar to
their standard HID equivalents, allowing us to write a simple translation
function that takes arbitrary HID usages as input and which returns
the corresponding standard HID usage as output (if one exists). Switching
on this translated usage instead of the actual usage allows the existing
cases to apply to both modes of operation without having to explicitly
define every Custom HID usage.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The HID standard defines usages that allow digitizers to report the pen's
height, tilt, and rotation and which are used by Wacom's new "MobileStudio
Pro" devices.
Note that 'hidinput_calc_abs_res' expects ABS_Z (historically used by our
driver to report twist) to have linear units. To ensure it calculates a
resolution with the actually-angular units provided in the HID descriptor
we nedd to lie and tell it we're calculating it for the (rotational) ABS_RZ
axis instead.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The product name received from the string descriptor in the new MobileStudio
Pro line of tablets begins with "Wacom", which leads to unnecessary visual
noise in the device name when appended to the vendor name which also includes
"Wacom". Look for and fix cases like this.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
ISDv4 devices have long supported reporting data from each of two barrel
switches, but HID_DG_BARRELSWITCH2 itself was only recently standardized.
Prior to its adoption, ISDv4 devices would associate the bit indicating
the state of the second barrel switch with the "Undefined" 0x000D0000
usage. Although most such devices have explicit support, a few use the
HID_GENERIC codepath which ignores the "Undefined" usage.
This patch adds code which detects the presence of a pre-standard second
barrel switch and corrects the usage value so that the HID_GENERIC code
will declare its presence and report its state.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This just centralizes the logic used in both wacom_setup_numbered_buttons
and wacom_report_numbered_buttons so that they don't drift out of sync.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
We've defined several new usages (e.g. WACOM_G9_PEN and WACOM_G9_TOUCHSCREEN)
which aren't checked by the WACOM_PEN_FIELD and WACOM_FINGER_FIELD macros but
probably should be.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Our loose use of "pen" and "digitizer" in the naming of several of our
vendor-defined usages may be a source of confusion given that the terms
have specific meaning within the HID specification. "Pen" specifically
refers to "an integrated display that allows the use of a stylus" (e.g.
something like a tablet PC or Cintiq) wheras "Digitizer" is a better
fit for opaque tablets like an Intuos.
While we're at it, go ahead and rename the definitions to make them more
distinct and better match up with the convention used by HID (e.g. the use
of '_UP_' for usage pages) and make them more distinct.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When i2c-core doesn't find the IRQ associated to the GPIO because
the gpiochip is not available, it assigns -EPROBE_DEFER to the irq.
We need to bail out there and on any other error in an IRQ.
Signed-off-by: David Arcari <darcari@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This reverts commit a485923efbb8 ("HID: i2c-hid: Add support for ACPI
GPIO interrupts") and commit a7d2bf25a483 ("HID: i2c-hid: Do not fail
probing if gpiolib is not enabled") at the same time.
Since commit c884fbd45214 ("gpio / ACPI: Add support for retrieving
GpioInt resources from a device") i2c_core already set the IRQ by
looking into the ACPI tree and retrieving the gpioInt. So we just
have some boiler-plate here that is not needed anymore.
The only downside effect here is that now we are not exiting early
enough if the irq is set to -EPROBE_DEFER or any other error, but
this is going to be fixed in the following patch.
Signed-off-by: David Arcari <darcari@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The Akai MIDImix (09e8:0031) is a MIDI fader controller that speaks
regular MIDI and works well with Linux. However, initialization gets
delayed due to reports timeout:
[3643645.631124] hid-generic 0003:09E8:0031.0020: timeout initializing reports
[3643645.632416] hid-generic 0003:09E8:0031.0020: hiddev0: USB HID v1.11 Device [AKAI MIDI Mix] on usb-0000:00:14.0-2/input0
Adding "usbhid.quirks=0x09e8:0x0031:0x20000000" on the kernel
command line makes the issues go away.
Signed-off-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This reverts commit 18339f59c3a6 ("HID: dragonrise: fix HID...") because it
breaks certain dragonrise 0079:0006 gamepads. While it may fix a breakage
caused by commit 79346d620e9d ("HID: input: force generic axis to be mapped
to their user space axis"), it is probable that the manufacturer released
different hardware with the same PID so this fix works for only a subset
and breaks the other gamepads sharing the PID.
What is needed is another more generic solution which fixes 79346d620e9d
("HID: input: force generic axis ...") breakage for this controller: we
need to add an exception for this driver to make it keep the old behaviour
previous to the initial breakage (this is done in patch 2 of this series).
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit 79346d620e9d ("HID: input: force generic axis to be mapped to their
user space axis") made mapping generic axes to their userspace equivalents
mandatory and some lower end gamepads which were depending on the previous
behaviour suffered severe regressions because they were reusing axes and
expecting hid-input to multiplex their map to the respective userspace axis
by always searching for and using the next available axis.
One solution is to add a hid quirk for this type of "previous" behaviour in
hid-input to bypass the new axes policy in favour of the old one, but since
only one hardware vendor seems to be affected negatively we're better off
making and exception and mapping in the driver for now; if more vendors or
drivers turn out to experience the problem we should reconsider the quirk
solution.
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The hid-led driver works fine under 4.8.0, however with the next
kernel from today I get this:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2578 at drivers/usb/core/hcd.c:1584 usb_hcd_map_urb_for_dma+0x373/0x550 [usbcore]
transfer buffer not dma capable
Modules linked in: hid_led(+) usbhid vfat fat ir_sony_decoder iwlmvm led_class mac80211 snd_hda_codec_realtek snd_hda_codec_generic x86_pkg_temp_thermal iwlwifi crc32c_intel snd_hda_codec_hdmi i2c_i801 i2c_smbus snd_hda_intel cfg80211 snd_hda_codec snd_hda_core snd_pcm r8169 snd_timer mei_me mii snd mei ir_lirc_codec lirc_dev nuvoton_cir rc_core btusb btintel bluetooth rfkill usb_storage efivarfs ipv6 ehci_pci ehci_hcd xhci_pci xhci_hcd usbcore usb_common ext4 jbd2 mbcache ahci libahci libata
CPU: 0 PID: 2578 Comm: systemd-udevd Not tainted 4.8.0-rc8-next-20161003 #1
Hardware name: ZOTAC ZBOX-CI321NANO/ZBOX-CI321NANO, BIOS B246P105 06/01/2015
ffffc90003dbb7e0 ffffffff81280425 ffffc90003dbb830 0000000000000000
ffffc90003dbb820 ffffffff8105b086 0000063003dbb800 ffff88006f374480
0000000000000000 0000000000000000 0000000000000001 ffff880079544000
Call Trace:
[<ffffffff81280425>] dump_stack+0x68/0x93
[<ffffffff8105b086>] __warn+0xc6/0xe0
[<ffffffff8105b0ea>] warn_slowpath_fmt+0x4a/0x50
[<ffffffffa0143a43>] usb_hcd_map_urb_for_dma+0x373/0x550 [usbcore]
[<ffffffffa01441b6>] usb_hcd_submit_urb+0x316/0x9c0 [usbcore]
[<ffffffff810bce80>] ? rcu_read_lock_sched_held+0x40/0x80
[<ffffffff810e0043>] ? module_assert_mutex_or_preempt+0x13/0x50
[<ffffffff810e0c07>] ? __module_address+0x27/0xf0
[<ffffffffa01456e4>] usb_submit_urb+0x2c4/0x520 [usbcore]
[<ffffffffa0145fea>] usb_start_wait_urb+0x5a/0xe0 [usbcore]
[<ffffffffa014612c>] usb_control_msg+0xbc/0xf0 [usbcore]
[<ffffffff810e0c07>] ? __module_address+0x27/0xf0
[<ffffffffa079a724>] usbhid_raw_request+0xa4/0x180 [usbhid]
[<ffffffffa07a93b1>] hidled_recv+0x71/0xe0 [hid_led]
[<ffffffffa07a947d>] thingm_init+0x2d/0x50 [hid_led]
[<ffffffffa07a969b>] hidled_probe+0xcb/0x24a [hid_led]
[<ffffffff814d96f2>] hid_device_probe+0xd2/0x150
[<ffffffff8146023d>] driver_probe_device+0x1fd/0x2c0
[<ffffffff8146039a>] __driver_attach+0x9a/0xa0
[<ffffffff81460300>] ? driver_probe_device+0x2c0/0x2c0
[<ffffffff8145e25d>] bus_for_each_dev+0x5d/0x90
[<ffffffff8145fa79>] driver_attach+0x19/0x20
[<ffffffff8145f5ff>] bus_add_driver+0x11f/0x220
[<ffffffffa07ac000>] ? 0xffffffffa07ac000
[<ffffffff8146086b>] driver_register+0x5b/0xd0
[<ffffffffa07ac000>] ? 0xffffffffa07ac000
[<ffffffff814d83d1>] __hid_register_driver+0x61/0xa0
[<ffffffffa07ac01e>] hidled_driver_init+0x1e/0x20 [hid_led]
[<ffffffff81000408>] do_one_initcall+0x38/0x150
[<ffffffff810bce80>] ? rcu_read_lock_sched_held+0x40/0x80
[<ffffffff81194ca0>] ? kmem_cache_alloc_trace+0x1d0/0x230
[<ffffffff811342f9>] do_init_module+0x5a/0x1cb
[<ffffffff810e3862>] load_module+0x1e42/0x2530
[<ffffffff810e0990>] ? __symbol_put+0x50/0x50
[<ffffffff810dfc50>] ? show_coresize+0x30/0x30
[<ffffffff811ad650>] ? kernel_read_file+0x100/0x190
[<ffffffff811ad794>] ? kernel_read_file_from_fd+0x44/0x70
[<ffffffff810e415a>] SYSC_finit_module+0xba/0xc0
[<ffffffff810e4179>] SyS_finit_module+0x9/0x10
[<ffffffff815e082a>] entry_SYSCALL_64_fastpath+0x18/0xad
---[ end trace c9e6ea27003ecf9e ]---
Fix this by using a kmalloc'ed buffer when calling hid_hw_raw_request.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Support additional DS4 model.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The motion sensor values are 16-bit, so make the value range match.
It is hard to reach the upper values, but they can be reached. At
least the current accelerometer value of 8192 is very easy to pass.
It is still not nice that the motion sensors live in no man's land
in between ABS_MISC and ABS_MT_SLOT, but that's something for another
time, which the proposed ABS_ACCEL_*/ABS_GYRO_* were meant for.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Read the touch history field in the HID descriptor and use this value
to determine how many touch events to read from the report. As part
of this patch, we did a first attempt of making the offset calculation
code less magical.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add a CRC value to each output report. This removes the need for the
'no output reports on interrupt end-point' quirk.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Put the report type (feature / output) in the report size definitions.
This prevents name collisions later on for other different reports, which use
the same report id, but have a different size.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Early on the sony_probe function calls hid_hw_start to start the hardware.
Afterwards it issues some hardware requests, initializes other functionality
like Force Feedback, power classes and others. However by the time
hid_hw_start returns, the device nodes have already been created, which leads
to a race condition by user space applications which may detect the device
prior to completion of initialization. We have observed this problem many
times, this patch fixes the problem.
This patch moves most of sony_probe to sony_input_configured, which is called
prior to device registration. This fixes the race condition and the same
approach is used in other HID drivers.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- Integrated Sensor Hub support (Cherrytrail+) from Srinivas Pandruvada
- Big cleanup of Wacom driver; namely it's now using devres, and the
standardized LED API so that libinput doesn't need to have root
access any more, with substantial amount of other cleanups
piggy-backing on top. All this from Benjamin Tissoires
- Report descriptor parsing would now ignore and out-of-range System
controls in case of the application actually being System Control.
This fixes quite some issues with several devices, and allows us to
remove a few ->report_fixup callbacks. From Benjamin Tissoires
- ... a lot of other assorted small fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (76 commits)
HID: add missing \n to end of dev_warn messages
HID: alps: fix multitouch cursor issue
HID: hid-logitech: Documentation updates/corrections
HID: hid-logitech: Improve Wingman Formula Force GP support
HID: hid-logitech: Rewrite of descriptor for all DF wheels
HID: hid-logitech: Compute combined pedals value
HID: hid-logitech: Add combined pedal support Logitech wheels
HID: hid-logitech: Introduce control for combined pedals feature
HID: sony: Update copyright and add Dualshock 4 rate control note
HID: sony: Defer the initial USB Sixaxis output report
HID: sony: Relax duplicate checking for USB-only devices
Revert "HID: microsoft: fix invalid rdesc for 3k kbd"
HID: alps: fix error return code in alps_input_configured()
HID: alps: fix stick device not working after resume
HID: support for keyboard - Corsair STRAFE
HID: alps: Fix memory leak
HID: uclogic: Add support for UC-Logic TWHA60 v3
HID: uclogic: Override constant descriptors
HID: uclogic: Support UGTizer GP0610 partially
HID: uclogic: Add support for several more tablets
...
|
|
'for-4.9/hid-input', 'for-4.9/intel-ish', 'for-4.9/kye-uclogic-waltop-fixes', 'for-4.9/logitech', 'for-4.9/sony', 'for-4.9/upstream' and 'for-4.9/wacom' into for-linus
|
