| Age | Commit message (Collapse) | Author |
|---|
|
This mouse keeps disconnecting in runlevel 3. It needs the ALWAYS_POLL quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The report descriptor for the HOLTEK USB ID 04d9:a0c2 (ETEKCITY Scroll
T-140 Gaming Mouse) is set to a very large amount of consumer usages
(2^16), exceeding HID_MAX_USAGES. Added id, bindings and comments for
the mouse, added to hid_have_special_driver, and reduced the usage and
logical maximums to 0x2fff, consistent with the other mice in the
category. Tested on the hardware.
Signed-off-by: John C. DeSilva <desilvjo@umich.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Hans Petter Selasky <hps@selasky.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Enable the always-poll quirk for Elan Touchscreens found on some recent
Samsung laptops.
Without this quirk the device keeps disconnecting from the bus (and is
re-enumerated) unless opened (and kept open, should an input event
occur).
Note that while the device can be run-time suspended, the autosuspend
timeout must be high enough to allow the device to be polled at least
once before being suspended. Specifically, using autosuspend_delay_ms=0
will still cause the device to disconnect on input events.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add quirk to make sure that a device is always polled for input events
even if it hasn't been opened.
This is needed for devices that disconnects from the bus unless the
interrupt endpoint has been polled at least once or when not responding
to an input event (e.g. after having shut down X).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch adds a seperate hid-penmount driver to work
around an issue with the HID report descriptor. The
descriptor does not contain the ContactID usage and as
result the touchscreen is represented as normal mouse
to the system.
This driver maps the button 0 emitted by the touchscreen
to BTN_TOUCH. This makes it possible to use touch events
in userspace.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
thingm_remove_rgb() needs to flush the workqueue after all the LED classes
have been unregistered, otherwise the removal might race with another LED
event coming, causing thingm_led_set() to schedule additional work after
thingm_remove_rgb() has flushed it. This obviously causes oops later, as
the scheduled work has been freed in the meantime.
In addition to that, move the hid_hw_stop() to an earlier place, so that
dmesg is not polluted by failure messages about not being able to write
the LED while the device is being shut down.
Reported-and-tested-by: Dylan Alex Simon <dylan-kernel@dylex.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Adding USB_DEVICE_ID_STM_HID_SENSOR again in the quirk table. During 3.16 merge
cycle somehow quirk for device id USB_DEVICE_ID_STM_HID_SENSOR is missing.
I see commit dde3b45cd74e ("HID: hid-sensor-hub: new device id and quirk
for STM Sensor hub") added new id USB_DEVICE_ID_STM_HID_SENSOR_1,
but didn't really delete the old device id.
Anyway we need to add this back, otherwise it breaks ST sensor hubs.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
In case of an unsupported firmware, the driver bails out without setting
the LEDs interfaces, but forget to set the proper error code.
err is then still equal to 0 and the hid subsytem consider the device
to be in perfect shape.
When removing it, thingm_remove() tries to unbind the rgb LEDs which
has not been created, leading to a segfault.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The Wacom Cintiq Companion shares the same sensor than the Cintiq
Companion Hybrid, with the exception of the different PIDs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch changes the way usbhid carries out Clear-Halt and reset.
Currently, after a Clear-Halt on the interrupt-IN endpoint, the driver
immediately restarts the interrupt URB, even if the Clear-Halt failed.
This doesn't work out well when the reason for the failure was that
the device was disconnected (when a low- or full-speed device is
connected through a hub to an EHCI controller, transfer errors caused
by disconnection are reported as stalls by the hub). Instead now the
driver will attempt a reset after a failed Clear-Halt.
The way resets are carried out is also changed. Now the driver will
call usb_queue_reset_device() instead of calling usb_reset_device()
directly. This avoids a deadlock that would arise when a device is
unplugged: The hid_reset() routine runs as a workqueue item, a reset
attempt after the device has been unplugged will fail, failure will
cause usbhid to be unbound, and the disconnect routine will try to do
cancel_work_sync(). The usb_queue_reset_device() implementation is
carefully written to handle scenarios like this one properly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Bit 3 in byte 31 of the Sixaxis report indicates whether the battery is
charging or not charging as opposed to whether or not the cable is plugged in.
As a result, when connected via USB and fully charged, the power_supply status
is wrongly reported as 'Discharging' instead of 'Full'.
Use the battery level value to set the cable state so that the power status
is reported correctly as that seems to be the only reliable way to determine the
cable status on the Sixaxis.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
picolcd device is not expected to send any report with size larger than
64 bytes.
If this impossible event happens (sic!), print also a report ID to allow
for easier debugging.
Suggested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
We can do once the test of the validity of the dj_device, which removes
some duplicated code in various functions.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fixes for potential memory corruption problems in magicmouse and
picolcd drivers (the HW would have to be manufactured to be
deliberately evil to trigger those) which were found by Steven
Vittitoe
- fix for false error message appearing in dmesg from logitech-dj
driver, from Benjamin Tissoires
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: picolcd: sanity check report size in raw_event() callback
HID: magicmouse: sanity check report size in raw_event() callback
HID: logitech-dj: prevent false errors to be shown
|
|
The report passed to us from transport driver could potentially be
arbitrarily large, therefore we better sanity-check it so that raw_data
that we hold in picolcd_pending structure are always kept within proper
bounds.
Cc: stable@vger.kernel.org
Reported-by: Steven Vittitoe <scvitti@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The report passed to us from transport driver could potentially be
arbitrarily large, therefore we better sanity-check it so that
magicmouse_emit_touch() gets only valid values of raw_id.
Cc: stable@vger.kernel.org
Reported-by: Steven Vittitoe <scvitti@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Atmel 840B digitizer presents a stylus interface which reports twice
the X coordinate and then twice the Y coordinate. In its current
implementation, hid-input assign the first X to X, then the second to Y,
then the first Y to Z, then the second one to RX.
This is wrong, and X should always be mapped to X, no matter what.
A solution consists in forcing X, Y, Z, RX, RY, RZ to be mapped to their
correct user space counter part.
Reported-by: Éric Brunet <Eric.Brunet@lps.ens.fr>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This makes UHID_START include a "dev_flags" field that describes details
of the hid-device in the kernel. The first flags we introduce describe
whether a given report-type uses numbered reports. This is useful for
transport layers that force report-numbers and therefore might have to
prefix kernel-provided HID-messages with the report-number.
Currently, only HoG needs this and the spec only talks about "global
report numbers". That is, it's a global boolean not a per-type boolean.
However, given the quirks we already have in kernel-space, a per-type
value seems much more appropriate.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
We so far lacked support for hid_hw_raw_request(..., HID_REQ_SET_REPORT);
Add support for it and simply forward the request to user-space. Note that
SET_REPORT is synchronous, just like GET_REPORT, even though it does not
provide any data back besides an error code.
If a transport layer does SET_REPORT asynchronously, they can just ACK it
immediately by writing an uhid_set_report_reply to uhid.
This patch re-uses the synchronous uhid-report infrastructure to query
user-space. Note that this means you cannot run SET_REPORT and GET_REPORT
in parallel. However, that has always been a restriction of HID and due to
its blocking nature, this is just fine. Maybe some future transport layer
supports parallel requests (very unlikely), however, until then lets not
over-complicate things and avoid request-lookup-tables.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
We use strict prefixed in uhid.c:
uhid_char_*: implement char-dev callbacks
uhid_dev_*: implement uhid device management and runtime
uhid_hid_*: implement hid-dev callbacks
uhid_raw_request is an hid callback, so rename it to uhid_hid_raw_request.
While at it, move it closer to it's extracted helpers and keep the same
order as in "struct hid_driver".
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The old hdev->hid_get_raw_report() was broken by design. It was never
clear what kind of HW request it should trigger. Benjamin fixed that with
the core HID cleanup, though we never really adjusted uhid.
Unfortunately, our old UHID_FEATURE command was modelled around the broken
hid_get_raw_report(). We converted it silently to the new GET_REPORT and
nothing broke. Make this explicit by renaming UHID_FEATURE to
UHID_GET_REPORT and UHID_FEATURE_ANSWER to UHID_GET_REPORT_REPLY.
Note that this is 100% ABI compatible to UHID_FEATURE. This is just a
rename. But we have to keep the old definitions around to not break API.
>From now on, UHID_GET_REPORT must trigger a GET_REPORT request on the
user-space hardware layer. All the ambiguity due to the weird "feature"
name should be gone now.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
All accesses to @report_done are protected by qlock (or report-contexts).
No need to use an atomic.
While at it, invert the logic and call it "report_running". This is
similar to the uhid->running field and easier to read.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
All accesses to @report_id are protected by @qlock. No need to use an
atomic.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Avoid hard-coding the target buffer sizes and use sizeof() instead. This
also makes us future-proof to buffer-extensions later on.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Avoid keeping uhid->rd_data and uhid->rd_size set in case
uhid_dev_create2() fails. This is non-critical as we never flip
uhid->running and thus never enter uhid_dev_destroy(). However, it's much
nicer for debugging if pointers are only set if they point to valid data.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Instead of hard-coding the uhid_dev_create() function twice, copy any
create_req into a create2_req structure and forward it.
We allocate uhid_create_req on the stack here, but that should be fine.
Unlike uhid_create2_req it is fairly small (<1KB) and it's only used
temporarily to swap entries. uhid_dev_create2() doesn't access it.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The report-query is blocking, so when user-space destroys a device we have
to wake up any blocking kernel context that is currently in the report-cb.
We used some broken correlation between @report_done and @running so far.
Replace it by a much more obvious use.
We now wake up the report-cb if either @report_done or @running is set.
wake_up() and wait_event() serve as implicit barriers (as they always do)
so no need to use smp_rmb/wmb directly.
Note that @report_done is never reset by anyone but the report-cb, thus
it cannot flip twice while we wait for it. And whenever we set @running,
we afterwards synchronously remove the HID device. Therefore, we wait for
all report-cbs to finish before we return. This way, @running can never
flip to true while we wait for it.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit "HID: logitech: perform bounds checking on device_id early
enough" unfortunately leaks some errors to dmesg which are not real
ones:
- if the report is not a DJ one, then there is not point in checking
the device_id
- the receiver (index 0) can also receive some notifications which
can be safely ignored given the current implementation
Move out the test regarding the report_id and also discards
printing errors when the receiver got notified.
Fixes: ad3e14d7c5268c2e24477c6ef54bbdf88add5d36
Cc: stable@vger.kernel.org
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fixes for a couple potential memory corruption problems (the HW would
have to be manufactured to be deliberately evil to trigger those)
found by Ben Hawkes
- fix for potential infinite loop when using sysfs interface of
logitech driver, from Simon Wood
- a couple more simple driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix a couple of off-by-ones
HID: logitech: perform bounds checking on device_id early enough
HID: logitech: fix bounds checking on LED report size
HID: logitech: Prevent possibility of infinite loop when using /sys interface
HID: rmi: print an error if F11 is not found instead of stopping the device
HID: hid-sensor-hub: use devm_ functions consistently
HID: huion: Use allocated buffer for DMA
HID: huion: Fail on parameter retrieval errors
|
|
There are a few very theoretical off-by-one bugs in report descriptor size
checking when performing a pre-parsing fixup. Fix those.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
device_index is a char type and the size of paired_dj_deivces is 7
elements, therefore proper bounds checking has to be applied to
device_index before it is used.
We are currently performing the bounds checking in
logi_dj_recv_add_djhid_device(), which is too late, as malicious device
could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the
problem in one of the report forwarding functions called from
logi_dj_raw_event().
Fix this by performing the check at the earliest possible ocasion in
logi_dj_raw_event().
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The check on report size for REPORT_TYPE_LEDS in logi_dj_ll_raw_request()
is wrong; the current check doesn't make any sense -- the report allocated
by HID core in hid_hw_raw_request() can be much larger than
DJREPORT_SHORT_LENGTH, and currently logi_dj_ll_raw_request() doesn't
handle this properly at all.
Fix the check by actually trimming down the report size properly if it is
too large.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer fixes from Dmitry Torokhov:
"Second round of updates for the input subsystem. Mostly small fixups
to the code merged in the first round (atmel_mxt_ts, wacom) but also a
smallish patch to xbox driver to support Xbox One controllers and a
patch to better handle Synaptics profile sensors found in Cr-48
Chromebooks that should not affect any other devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: edt-ft5x06 - remove superfluous assignment
Input: xpad - add support for Xbox One controllers
Input: atmel_mxt_ts - fix a few issues reported by Coverity
Input: atmel_mxt_ts - split config update a bit
Input: atmel_mxt_ts - simplify mxt_initialize a bit
Input: joystick - use get_cycles on ARMv8
Input: wacom - fix compiler warning if !CONFIG_PM
Input: cap1106 - allow changing key mapping from userspace
Input: synaptics - use firmware data for Cr-48
Input: synaptics - properly initialize slots for semi-MT
Input: MT - make slot cleanup callable outside mt_sync_frame()
Input: atmel_mxt_ts - mXT224 DMA quirk was fixed in firmware v2.0.AA
|
|
If the device data is not accessible for some reason, returning 0 will cause the call to be
continuously called again as none of the string has been 'consumed'.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Currently rmi_probe will return -EIO if the device doesn't report that it has F11.
This would indicate that something happened and the device is in the bootloader.
We can recover the device using a userspace firmware update tool, but it needs
access to the device through the hidraw device file. If the probe returns -EIO
the hidraw device won't be created. So instead of failing the probe, just print
an error message, but leave the device accessible from userspace.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If CONFIG_PM is not set:
drivers/hid/wacom_sys.c:1436: warning: ‘wacom_reset_resume’ defined but
not used
Protect the unused functions by #ifdef CONFIG_PM to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use devm_kzalloc for all calls to kzalloc and not just the first. Use
devm functions for other allocations as well. The calls to free the
allocated memory in the probe and remove functions are done away with
and a label is removed in the probe function.
The semantic match that finds the inconsistency is as follows:
// <smpl>
@@
@@
*devm_kzalloc(...)
...
*kzalloc(...)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Allocate a buffer with kmalloc for receiving the parameters string
descriptor with usb_control_msg, instead of using a buffer on the stack,
as the latter is unsafe. Use an enum for indices into the buffer to
ensure the buffer size if sufficient.
This fixes the static checker error "doing dma on the stack (buf)".
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fail Huion tablet interface enabling and probing, if parameter retrieval
fails. Move the main code path out of the else block accordingly.
This should prevent devices appearing in a half-working state due to
original report descriptor being used, simplifying diagnostics. This
also makes it easier to add cleanup in later commits, as error handling
is simplified.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- big update to Wacom driver by Benjamin Tissoires, converting it to
HID infrastructure and unifying USB and Bluetooth models
- large update to ALPS driver by Hans de Goede, which adds support for
newer touchpad models as well as cleans up and restructures the code
- more changes to Atmel MXT driver, including device tree support
- new driver for iPaq x3xxx touchscreen
- driver for serial Wacom tablets
- driver for Microchip's CAP1106
- assorted cleanups and improvements to existing drover and input core
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (93 commits)
Input: wacom - update the ABI doc according to latest changes
Input: wacom - only register once the MODULE_* macros
Input: HID - remove hid-wacom Bluetooth driver
Input: wacom - add copyright note and bump version to 2.0
Input: wacom - remove passing id for wacom_set_report
Input: wacom - check for bluetooth protocol while setting OLEDs
Input: wacom - handle Intuos 4 BT in wacom.ko
Input: wacom - handle Graphire BT tablets in wacom.ko
Input: wacom - prepare the driver to include BT devices
Input: hyperv-keyboard - register as a wakeup source
Input: imx_keypad - remove ifdef round PM methods
Input: jornada720_ts - get rid of space indentation and use tab
Input: jornada720_ts - switch to using managed resources
Input: alps - Rushmore and v7 resolution support
Input: mcs5000_ts - remove ifdef around power management methods
Input: mcs5000_ts - protect PM functions with CONFIG_PM_SLEEP
Input: ads7846 - release resources on failure for clean exit
Input: wacom - add support for 0x12C ISDv4 sensor
Input: atmel_mxt_ts - use deep sleep mode when stopped
ARM: dts: am437x-gp-evm: Update binding for touchscreen size
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED updates from Bryan Wu:
"This cycle we got:
- a fix of attribute-creation race for the whole leds subsystem
- new drivers (HID:GT683R, leds-ipaq-micro)
- other fixing and clean up"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (23 commits)
leds: ipaq-micro: fix sparse non static symbol warning
leds: add driver for the iPAQ micro
Documentation: dts: tcs6507: Fix wrong statement about #gpio-cells
leds: convert blink timer to workqueue
leds:pca963x: Update for PCA9635 and correct statement about MODE2 OUTDRV default
leds:pca963x: Always initialize MODE2 register
leds:pca963x: Add support for PCA9635 LED driver chip
HID: gt683r: move mode attribute to led-class devices
HID: gt683r: fix race condition
HID: add support for MSI GT683R led panels
leds: lp55xx-common: fix attribute-creation race
leds: lp55xx-common: fix sysfs entry leak
input: lm8323: fix attribute-creation race
leds: wm831x-status: fix attribute-creation race
leds: ss4200: fix attribute-creation race
leds: ns2: fix attribute-creation race
leds: netxbig: fix attribute-creation race
leds: max8997: fix attribute-creation race
leds: lm3642: fix attribute-creation race
leds: lm355x: fix attribute-creation race
...
|
|
Prepare first round of input updates for 3.17.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
"Some highlights:
- hid-sony improvements of Sixaxis device support by Antonio Ospite
- hid-hyperv driven devices can now be used as wakeup source, by
Dexuan Cui
- hid-lenovo driver is now more generic and supports more devices, by
Jamie Lentin
- hid-huion now supports wider range of tablets, by Nikolai
Kondrashov
- other various unsorted fixes and device ID additions"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
HID: hyperv: register as a wakeup source
HID: sony: Default initialize all elements of the LED max_brightness array to 1
HID: huion: Fix sparse warnings
HID: usbhid: Use flag HID_DISCONNECTED when a usb device is removed
HID: ignore jabra gn9350e
HID: cp2112: add I2C mode
HID: use multi input quirk for 22b9:2968
HID: rmi: only bind the hid-rmi driver to the mouse interface of composite USB devices
HID: rmi: check that report ids exist in the report_id_hash before accessing their size
HID: lenovo: Add support for Compact (BT|USB) keyboard
HID: lenovo: Don't call function in condition, show error codes
HID: lenovo: Prepare support for adding other devices
HID: lenovo: Rename hid-lenovo-tpkbd to hid-lenovo
HID: huion: Handle tablets with UC-Logic vendor ID
HID: huion: Switch to generating report descriptor
HID: huion: Don't ignore other interfaces
HID: huion: Use "tablet" instead of specific model
HID: add quirk for 0x04d9:0xa096 device
HID: i2c-hid: call the hid driver's suspend and resume callbacks
HID: rmi: change logging level of log messages related to unexpected reports
...
|
|
Putting the various MODULE_* makes them appear several times in modinfo
because wacom.h is used both in wacom_sys.c and wacom_wac.h.
Having the macros near the module declaration makes them appear only once.
Add also MODULE_VERSION(DRIVER_VERSION) to export the current version
number.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Bluetooth Wacom tablets are now handled by the regular wacom.ko driver.
Remove the now useless hid-wacom driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Every call of wacom_set_report was passing "id" as a separate parameter
and buffer also passed the same information. We can use first u8 of the
buffer instead of "id"
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Bluetooth Intuos 4 use 1-bit definition while the USB ones use a 4-bits
definition. This changes the size of the raw image we receive, and thus
the kernel will only accept 1-bit images for Bluetooth and 4-bits for
USB.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
A good point of this change is that now, the Intuos4 bluetooth can handle
the different tools (artpen, airbrush, mice), and we get a common interface
between USB and BT for accessing the LEDs/OLEDs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
