| Age | Commit message (Collapse) | Author |
|---|
|
inno_hdmi_init_hw
Putting these scattered initialization code together is helpful
for the following migration to the DRM bridge driver mode.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250512124615.2848731-6-andyshrk@163.com
|
|
This function not only configure hardware reset register, but also
do some other configurations. Therefore, it is more appropriate to
name it inno_hdmi_init_hw, which will also facilitate the addition
of other functions to this function in the following patch.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250512124615.2848731-5-andyshrk@163.com
|
|
Remove unnecessary parentheses to make checkpatch happy.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250512124615.2848731-4-andyshrk@163.com
|
|
1. Prefer using the BIT macro
2. Macro argument 'n' as '(n)' to avoid precedence issues
3. Add a blank line after enum declarations
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250512124615.2848731-3-andyshrk@163.com
|
|
Since this register definition is only use in one single c
file, there is no need to put it in a separate header.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250512124615.2848731-2-andyshrk@163.com
|
|
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs.
Signed-off-by: Yumeng Fang <fang.yumeng@zte.com.cn>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250515203554564-j1jBXUXR6bdiN6zARicC@zte.com.cn
|
|
Convert it to drm bridge driver, it will be convenient for us to
migrate the connector part to the display driver later.
Considering that some code depend on the connector, the following
changes have been made:
- Only process edid in &drm_bridge_funcs.edid_read(), so no need to
store additional edid info.
- Now cdn_dp_get_sink_capability() only focused on reading DPCD_REV.
- Update bpc info in cdn_dp_bridge_atomic_enable() instead of
cdn_dp_encoder_mode_set(). Actually, the bpc data will be used in
cdn_dp_bridge_atomic_enable().
- Switch to use DRM_BRIDGE_OP_DP_AUDIO helpers.
This patch also convert to use devm_drm_bridge_alloc() API.
Tested with RK3399 EVB IND board.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250529071334.441-1-kernel@airkyi.com
|
|
Each window of a vop2 is usable by a specific set of video ports, so while
binding the vop2, we look through the list of available windows trying to
find one designated as primary-plane and usable by that specific port.
The code later wants to use drm_crtc_init_with_planes with that found
primary plane, but nothing has checked so far if a primary plane was
actually found.
For whatever reason, the rk3576 vp2 does not have a usable primary window
(if vp0 is also in use) which brought the issue to light and ended in a
null-pointer dereference further down.
As we expect a primary-plane to exist for a video-port, add a check at
the end of the window-iteration and fail probing if none was found.
Fixes: 604be85547ce ("drm/rockchip: Add VOP2 driver")
Reviewed-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250610212748.1062375-1-heiko@sntech.de
|
|
Convert it to drm bridge driver, it will be convenient for us to
migrate the connector part to the display driver later.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
[on a not-upstream px30 board with lvds display]
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250526015834.102-1-kernel@airkyi.com
|
|
Pull in drm-intel-next for the updates to drm panic handling.
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
|
|
Panther Lake has proven to be stable through testing and use.
Remove the force_probe requirement and enable the platform by default.
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://lore.kernel.org/r/20250707201959.319406-1-matthew.s.atwood@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
Updates for v6.17
CI:
- uprev mesa and ci-templates
- use shallow clone to speed up build jobs
- remove sdm845/cheza jobs. These runners are no more (RIP
dear chezas)
- fix runner tag for i915 cml runners
- uprev igt to pull in msm test fixes
Core:
- VM_BIND support!
- single source of truth for UBWC configuration. Adds a global soc
driver for UBWC config which is used from display and GPU. (And
later vidc/camera/etc)
- Decouple ties between GPU and KMS, adding a `separate_gpu_kms`
modparam to allow the GPU and KMS to bind to separate DRM devices.
This should better deal with more exotic SoC configurations where
the number of GPUs is different from number of DPUs. The default
behavior is to still come up as a single unified DRM device to
avoid surprising userspace.
DP:
- major rework of the I/O accessors
DPU:
- use version checks instead of feature bits
- SM8750 support
- set min_prefill_lines for SC8180X
DSI:
- SM8750 support
GPU:
- speedbin support for X1-85
- X1-45 support
MDSS:
- SM8750 support
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
From: Robin Clark <robin.clark@oss.qualcomm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACSVV0217R+kpoWQJeuYGHf6q_4aFyEJuKa=dZZKOnLQzFwppg@mail.gmail.com
|
|
https://gitlab.freedesktop.org/drm/i915/kernel into drm-next
drm/i915 feature pull #2 for v6.17:
Features and functionality:
- Add drm_panic support for both i915 and xe drivers (Jocelyn Falempe)
- Add initial flip queue implementation, disabled by default, for LNL and PTL
(Ville)
- Add support for Wildcat Lake (WCL) display, version 30.02 (Matt Roper, Matt
Atwood, Dnyaneshwar)
- Extend drm_panel and follower support to DDI eDP (Arun)
Refactoring and cleanups:
- Make all global state objects opaque (Jani)
- Move display works to display specific unordered workqueue (Luca)
- Add and use struct drm_device based pcode interface (Jani, Lucas)
- Use clamp() instead of max()+min() combo (Ankit)
- Simplify wait for power well disable (Jani)
- Various stylistics cleanups and renames (Jani)
Fixes:
- Deal with loss of pipe DMC state (Ville)
- Fix PTL HDCP2 stream status check (Suraj)
- Add workaround for ADL-P DKL PHY DP and HDMI (Nemesa)
- Fix skl_print_wm_changes() stack usage with KMSAN (Arnd Bergmann)
- Fix PCON capability reads on non-branch devices (Chaitanya)
- Fix which platforms have ultra joiner (Ankit)
DRM core changes:
- Add ttm_bo_kmap_try_from_panic() for xe drm_panic support (Jocelyn Falempe)
- Add private pointer to struct drm_scanout buffer for xe/i915 drm_panic support
(Jocelyn Falempe)
Merges:
- Backmerge drm-next for drm_panel and xe changes (Jani)
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6d728bf6ef23681b00dfbc7da9aeae41042dee02@intel.com
|
|
There looks to be an issue in our compression handling when the BO pages
are very fragmented, where we choose to skip the identity map and
instead fall back to emitting the PTEs by hand when migrating memory,
such that we can hopefully do more work per blit operation. However in
such a case we need to ensure the src PTEs are correctly tagged with a
compression enabled PAT index on dgpu xe2+, otherwise the copy will
simply treat the src memory as uncompressed, leading to corruption if
the memory was compressed by the user.
To fix this pass along use_comp_pat into emit_pte() on the src side, to
indicate that compression should be considered.
v2 (Jonathan): tweak the commit message
Fixes: 523f191cc0c7 ("drm/xe/xe_migrate: Handle migration logic for xe2+ dgfx")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Akshata Jahagirdar <akshata.jahagirdar@intel.com>
Cc: <stable@vger.kernel.org> # v6.12+
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Link: https://lore.kernel.org/r/20250701103949.83116-2-matthew.auld@intel.com
(cherry picked from commit f7a2fd776e57bd6468644bdecd91ab3aba57ba58)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
This reverts commit fe0154cf8222d9e38c60ccc124adb2f9b5272371.
Seeing some unexplained random failures during LRC context switches with
indirect ring state enabled. The failures were always there, but the
repro rate increased with the addition of WA BB as a separate BO.
Commit 3a1edef8f4b5 ("drm/xe: Make WA BB part of LRC BO") helped to
reduce the issues in the context switches, but didn't eliminate them
completely.
Indirect ring state is not required for any current features, so disable
for now until failures can be root caused.
Cc: stable@vger.kernel.org
Fixes: fe0154cf8222 ("drm/xe/xe2: Enable Indirect Ring State support for Xe2")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250702035846.3178344-1-matthew.brost@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 03d85ab36bcbcbe9dc962fccd3f8e54d7bb93b35)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
CIRC_SPACE does not work unless the size argument is a power of 2,
allocate PF queue size on power of 2 boundary.
Cc: stable@vger.kernel.org
Fixes: 3338e4f90c14 ("drm/xe: Use topology to determine page fault queue size")
Fixes: 29582e0ea75c ("drm/xe: Add page queue multiplier")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Francois Dugast <francois.dugast@intel.com>
Link: https://lore.kernel.org/r/20250702213511.3226167-1-matthew.brost@intel.com
(cherry picked from commit 491b9783126303755717c0cbde0b08ee59b6abab)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Our LMEM buffer objects are not cleared by default on alloc
and during VF provisioning we only setup LMTT PTEs for the
actually provisioned LMEM range. But beyond that valid range
we might leave some stale data that could either point to some
other VFs allocations or even to the PF pages.
Explicitly clear all new LMTT page to avoid the risk that a
malicious VF would try to exploit that gap.
While around add asserts to catch any undesired PTE overwrites
and low-level debug traces to track LMTT PT life-cycle.
Fixes: b1d204058218 ("drm/xe/pf: Introduce Local Memory Translation Table")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Lukasz Laguna <lukasz.laguna@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://lore.kernel.org/r/20250701220052.1612-1-michal.wajdeczko@intel.com
(cherry picked from commit 3fae6918a3e27cce20ded2551f863fb05d4bef8d)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Calling dev_pm_domain_attach()/dev_pm_domain_detach() in bus driver
probe/remove functions can affect system behavior when the drivers
attached to the bus use devres-managed resources. Since devres actions
may need to access device registers, calling dev_pm_domain_detach() too
early, i.e., before these actions complete, can cause failures on some
systems. One such example is Renesas RZ/G3S SoC-based platforms.
If the device clocks are managed via PM domains, invoking
dev_pm_domain_detach() in the bus driver's remove function removes the
device's clocks from the PM domain, preventing any subsequent
pm_runtime_resume*() calls from enabling those clocks.
The second argument of dev_pm_domain_attach() specifies whether the PM
domain should be powered on during attachment. Likewise, the second
argument of dev_pm_domain_detach() indicates whether the domain should be
powered off during detachment.
Upcoming changes address the issue described above (initially for the
platform bus only) by deferring the call to dev_pm_domain_detach() until
after devres_release_all() in device_unbind_cleanup(). The detach_power_off
field in struct dev_pm_info stores the detach power off info from the
second argument of dev_pm_domain_attach().
Because there are cases where the device's PM domain power-on/off behavior
must be conditional (e.g., in i2c_device_probe()), the patch introduces
PD_FLAG_ATTACH_POWER_ON and PD_FLAG_DETACH_POWER_OFF flags to be passed
to dev_pm_domain_attach().
Finally, dev_pm_domain_attach() and its users are updated to use the newly
introduced PD_FLAG_ATTACH_POWER_ON and PD_FLAG_DETACH_POWER_OFF macros.
This change is preparatory.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # I2C
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/20250703112708.1621607-2-claudiu.beznea.uj@bp.renesas.com
[ rjw: Changelog adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
[ +0.000020] BUG: KASAN: slab-use-after-free in amdgpu_userq_suspend+0x51a/0x5a0 [amdgpu]
[ +0.000817] Read of size 8 at addr ffff88812eec8c58 by task amd_pci_unplug/1733
[ +0.000027] CPU: 10 UID: 0 PID: 1733 Comm: amd_pci_unplug Tainted: G W 6.14.0+ #2
[ +0.000009] Tainted: [W]=WARN
[ +0.000003] Hardware name: ASUS System Product Name/ROG STRIX B550-F GAMING (WI-FI), BIOS 1401 12/03/2020
[ +0.000004] Call Trace:
[ +0.000004] <TASK>
[ +0.000003] dump_stack_lvl+0x76/0xa0
[ +0.000011] print_report+0xce/0x600
[ +0.000009] ? srso_return_thunk+0x5/0x5f
[ +0.000006] ? kasan_complete_mode_report_info+0x76/0x200
[ +0.000007] ? kasan_addr_to_slab+0xd/0xb0
[ +0.000006] ? amdgpu_userq_suspend+0x51a/0x5a0 [amdgpu]
[ +0.000707] kasan_report+0xbe/0x110
[ +0.000006] ? amdgpu_userq_suspend+0x51a/0x5a0 [amdgpu]
[ +0.000541] __asan_report_load8_noabort+0x14/0x30
[ +0.000005] amdgpu_userq_suspend+0x51a/0x5a0 [amdgpu]
[ +0.000535] ? stop_cpsch+0x396/0x600 [amdgpu]
[ +0.000556] ? stop_cpsch+0x429/0x600 [amdgpu]
[ +0.000536] ? __pfx_amdgpu_userq_suspend+0x10/0x10 [amdgpu]
[ +0.000536] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? kgd2kfd_suspend+0x132/0x1d0 [amdgpu]
[ +0.000542] amdgpu_device_fini_hw+0x581/0xe90 [amdgpu]
[ +0.000485] ? down_write+0xbb/0x140
[ +0.000007] ? __mutex_unlock_slowpath.constprop.0+0x317/0x360
[ +0.000005] ? __pfx_amdgpu_device_fini_hw+0x10/0x10 [amdgpu]
[ +0.000482] ? __kasan_check_write+0x14/0x30
[ +0.000004] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? up_write+0x55/0xb0
[ +0.000007] ? srso_return_thunk+0x5/0x5f
[ +0.000005] ? blocking_notifier_chain_unregister+0x6c/0xc0
[ +0.000008] amdgpu_driver_unload_kms+0x69/0x90 [amdgpu]
[ +0.000484] amdgpu_pci_remove+0x93/0x130 [amdgpu]
[ +0.000482] pci_device_remove+0xae/0x1e0
[ +0.000008] device_remove+0xc7/0x180
[ +0.000008] device_release_driver_internal+0x3d4/0x5a0
[ +0.000007] device_release_driver+0x12/0x20
[ +0.000004] pci_stop_bus_device+0x104/0x150
[ +0.000006] pci_stop_and_remove_bus_device_locked+0x1b/0x40
[ +0.000005] remove_store+0xd7/0xf0
[ +0.000005] ? __pfx_remove_store+0x10/0x10
[ +0.000006] ? __pfx__copy_from_iter+0x10/0x10
[ +0.000006] ? __pfx_dev_attr_store+0x10/0x10
[ +0.000006] dev_attr_store+0x3f/0x80
[ +0.000006] sysfs_kf_write+0x125/0x1d0
[ +0.000004] ? srso_return_thunk+0x5/0x5f
[ +0.000005] ? __kasan_check_write+0x14/0x30
[ +0.000005] kernfs_fop_write_iter+0x2ea/0x490
[ +0.000005] ? rw_verify_area+0x70/0x420
[ +0.000005] ? __pfx_kernfs_fop_write_iter+0x10/0x10
[ +0.000006] vfs_write+0x90d/0xe70
[ +0.000005] ? srso_return_thunk+0x5/0x5f
[ +0.000005] ? __pfx_vfs_write+0x10/0x10
[ +0.000004] ? local_clock+0x15/0x30
[ +0.000008] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? __kasan_slab_free+0x5f/0x80
[ +0.000005] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? __kasan_check_read+0x11/0x20
[ +0.000004] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? fdget_pos+0x1d3/0x500
[ +0.000007] ksys_write+0x119/0x220
[ +0.000005] ? putname+0x1c/0x30
[ +0.000006] ? __pfx_ksys_write+0x10/0x10
[ +0.000007] __x64_sys_write+0x72/0xc0
[ +0.000006] x64_sys_call+0x18ab/0x26f0
[ +0.000006] do_syscall_64+0x7c/0x170
[ +0.000004] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? __pfx___x64_sys_openat+0x10/0x10
[ +0.000006] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? __kasan_check_read+0x11/0x20
[ +0.000003] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? fpregs_assert_state_consistent+0x21/0xb0
[ +0.000006] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? syscall_exit_to_user_mode+0x4e/0x240
[ +0.000005] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? do_syscall_64+0x88/0x170
[ +0.000003] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? irqentry_exit+0x43/0x50
[ +0.000004] ? srso_return_thunk+0x5/0x5f
[ +0.000004] ? exc_page_fault+0x7c/0x110
[ +0.000006] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ +0.000006] RIP: 0033:0x7480c0b14887
[ +0.000005] Code: 10 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
[ +0.000005] RSP: 002b:00007fff142b0058 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ +0.000006] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007480c0b14887
[ +0.000003] RDX: 0000000000000001 RSI: 00007480c0e7365a RDI: 0000000000000004
[ +0.000003] RBP: 00007fff142b0080 R08: 0000563b2e73c170 R09: 0000000000000000
[ +0.000003] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff142b02f8
[ +0.000003] R13: 0000563b159a72a9 R14: 0000563b159a9d48 R15: 00007480c0f19040
[ +0.000008] </TASK>
[ +0.000445] Allocated by task 427 on cpu 5 at 29.342331s:
[ +0.000011] kasan_save_stack+0x28/0x60
[ +0.000006] kasan_save_track+0x18/0x70
[ +0.000006] kasan_save_alloc_info+0x38/0x60
[ +0.000005] __kasan_kmalloc+0xc1/0xd0
[ +0.000006] __kmalloc_cache_noprof+0x1bd/0x430
[ +0.000007] amdgpu_driver_open_kms+0x172/0x760 [amdgpu]
[ +0.000493] drm_file_alloc+0x569/0x9a0
[ +0.000007] drm_client_init+0x1b7/0x410
[ +0.000007] drm_fbdev_client_setup+0x174/0x470
[ +0.000006] drm_client_setup+0x8a/0xf0
[ +0.000006] amdgpu_pci_probe+0x510/0x10c0 [amdgpu]
[ +0.000483] local_pci_probe+0xe7/0x1b0
[ +0.000006] pci_device_probe+0x5bf/0x890
[ +0.000006] really_probe+0x1fd/0x950
[ +0.000005] __driver_probe_device+0x307/0x410
[ +0.000006] driver_probe_device+0x4e/0x150
[ +0.000005] __driver_attach+0x223/0x510
[ +0.000006] bus_for_each_dev+0x102/0x1a0
[ +0.000005] driver_attach+0x3d/0x60
[ +0.000006] bus_add_driver+0x309/0x650
[ +0.000005] driver_register+0x13d/0x490
[ +0.000006] __pci_register_driver+0x1ee/0x2b0
[ +0.000006] rfcomm_dlc_clear_state+0x69/0x220 [rfcomm]
[ +0.000011] do_one_initcall+0x9c/0x3e0
[ +0.000007] do_init_module+0x29e/0x7f0
[ +0.000006] load_module+0x5c75/0x7c80
[ +0.000006] init_module_from_file+0x106/0x180
[ +0.000006] idempotent_init_module+0x377/0x740
[ +0.000006] __x64_sys_finit_module+0xd7/0x180
[ +0.000006] x64_sys_call+0x1f0b/0x26f0
[ +0.000006] do_syscall_64+0x7c/0x170
[ +0.000005] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ +0.000013] Freed by task 1733 on cpu 5 at 59.907086s:
[ +0.000011] kasan_save_stack+0x28/0x60
[ +0.000006] kasan_save_track+0x18/0x70
[ +0.000005] kasan_save_free_info+0x3b/0x60
[ +0.000005] __kasan_slab_free+0x54/0x80
[ +0.000006] kfree+0x127/0x470
[ +0.000006] amdgpu_driver_postclose_kms+0x455/0x760 [amdgpu]
[ +0.000493] drm_file_free.part.0+0x5b1/0xba0
[ +0.000006] drm_file_free+0x13/0x30
[ +0.000006] drm_client_release+0x1c4/0x2b0
[ +0.000006] drm_fbdev_ttm_fb_destroy+0xd2/0x120 [drm_ttm_helper]
[ +0.000007] put_fb_info+0x97/0xe0
[ +0.000007] unregister_framebuffer+0x197/0x380
[ +0.000005] drm_fb_helper_unregister_info+0x94/0x100
[ +0.000005] drm_fbdev_client_unregister+0x3c/0x80
[ +0.000007] drm_client_dev_unregister+0x144/0x330
[ +0.000006] drm_dev_unregister+0x49/0x1b0
[ +0.000006] drm_dev_unplug+0x4c/0xd0
[ +0.000006] amdgpu_pci_remove+0x58/0x130 [amdgpu]
[ +0.000484] pci_device_remove+0xae/0x1e0
[ +0.000008] device_remove+0xc7/0x180
[ +0.000007] device_release_driver_internal+0x3d4/0x5a0
[ +0.000006] device_release_driver+0x12/0x20
[ +0.000007] pci_stop_bus_device+0x104/0x150
[ +0.000006] pci_stop_and_remove_bus_device_locked+0x1b/0x40
[ +0.000006] remove_store+0xd7/0xf0
[ +0.000006] dev_attr_store+0x3f/0x80
[ +0.000005] sysfs_kf_write+0x125/0x1d0
[ +0.000006] kernfs_fop_write_iter+0x2ea/0x490
[ +0.000006] vfs_write+0x90d/0xe70
[ +0.000006] ksys_write+0x119/0x220
[ +0.000006] __x64_sys_write+0x72/0xc0
[ +0.000006] x64_sys_call+0x18ab/0x26f0
[ +0.000005] do_syscall_64+0x7c/0x170
[ +0.000006] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ +0.000012] The buggy address belongs to the object at ffff88812eec8000
which belongs to the cache kmalloc-rnd-07-4k of size 4096
[ +0.000016] The buggy address is located 3160 bytes inside of
freed 4096-byte region [ffff88812eec8000, ffff88812eec9000)
[ +0.000023] The buggy address belongs to the physical page:
[ +0.000009] page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x12eec8
[ +0.000007] head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
[ +0.000005] flags: 0x17ffffc0000040(head|node=0|zone=2|lastcpupid=0x1fffff)
[ +0.000007] page_type: f5(slab)
[ +0.000008] raw: 0017ffffc0000040 ffff888100054500 dead000000000122 0000000000000000
[ +0.000005] raw: 0000000000000000 0000000080040004 00000000f5000000 0000000000000000
[ +0.000006] head: 0017ffffc0000040 ffff888100054500 dead000000000122 0000000000000000
[ +0.000005] head: 0000000000000000 0000000080040004 00000000f5000000 0000000000000000
[ +0.000006] head: 0017ffffc0000003 ffffea0004bbb201 ffffffffffffffff 0000000000000000
[ +0.000005] head: 0000000000000008 0000000000000000 00000000ffffffff 0000000000000000
[ +0.000005] page dumped because: kasan: bad access detected
[ +0.000010] Memory state around the buggy address:
[ +0.000009] ffff88812eec8b00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ +0.000012] ffff88812eec8b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ +0.000011] >ffff88812eec8c00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ +0.000011] ^
[ +0.000010] ffff88812eec8c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ +0.000011] ffff88812eec8d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ +0.000011] ==================================================================
The use-after-free occurs because a delayed work item (`suspend_work`) may still
be pending or running when resources it accesses are freed during device removal
or file close. The previous code used `flush_work(&fpriv->evf_mgr.suspend_work.work)`,
which does not wait for delayed work that has not yet started. As a result, the
delayed work could run after its memory was freed, causing a use-after-free.
By switching to `flush_delayed_work(&fpriv->evf_mgr.suspend_work)`, we ensure that
the kernel waits for both queued and delayed work to finish before
freeing memory, closing this race.
Fixes: adba0929736a ("drm/amdgpu: Fix Illegal opcode in command stream Error")
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 5fb90421fa0fbe0a968274912101fe917bf1c47b.
The original patch moved `amdgpu_userq_mgr_fini()` to the driver's
`postclose` callback, which is called after `drm_gem_release()` in
the DRM file cleanup sequence.If a user application crashes or aborts
without cleaning up its user queues, 'drm_gem_release()` may free
GEM objects that are still referenced by active user queues, leading
to use-after-free. By reverting, we ensure that user queues are
disabled and cleaned up before any GEM objects are released,
preventing this class of bug. However, this reintroduces a race
during PCI hot-unplug, where device removal can race with per-file
cleanup, leading to use-after-free in suspend/unplug paths.
This will be fixed in the next patch.
Fixes: 5fb90421fa0f ("drm/amdgpu: fix slab-use-after-free in amdgpu_userq_mgr_fini+0x70c")
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Common resolutions are added to supported modes to enable compatibility
scenarios that compositors may use to do things like clone displays. There
is no guarantee however that the panel will natively support these modes.
[How]
If the compositor hasn't enabled scaling but a non-native resolution has
been picked for an LVDS panel turn the scaler on anyway. This will ensure
compatibility.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Common modes are added to LVDS for compatibility in clone mode, but
not all panels support them. Non-native modes were disabled in the past
but this caused problems because compositors didn't use scaling for non
native modes. Now non-native modes on LVDS will enable the scaler by
default.
[How]
Check the connector type. If the connector is LVDS avoid adding common
modes.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add a parameter to amdgpu_sdma_reset_engine() to let the
caller handle the kernel rings. This allows the kernel
rings to back up their unprocessed state if the reset comes in
via the drm scheduler rather than KFD.
Reviewed-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Move the force completion handling into the common
engine reset function. No need to duplicate it for
every IP version.
Reviewed-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If ring reset is disabled, skip resetting queues. Instead, fall back to
device based reset.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For extended wait with retries on a PSP register value, add a noverbose
flag to avoid excessive error messages on each timeout.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There is a small typo in phm_wait_on_indirect_register().
Swap mask and value arguments provided to phm_wait_on_register() so that
they satisfy the function signature and actual usage scheme.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool.
In practice this doesn't fix any issues because the only place this
function is used uses the same value for the value and mask.
Fixes: 3bace3591493 ("drm/amd/powerplay: add hardware manager sub-component")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Need to reinit the ring before remapping it and all of
the KIQ handling needs to be within the kiq lock.
Fixes: 1741281a157f ("drm/amdgpu/gfx10: add ring reset callbacks")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pass amdgpu device context instead of drm device context to some
amdgpu_device_* functions. DRM device context is not required in those
functions. No functional change.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add the unversioned define for the PTL HuC FW.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250626182805.1701096-15-daniele.ceraolospurio@intel.com
|
|
The first official GuC relase for PTL is 70.47.0, which maps to
API version 1.22.4.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250626182805.1701096-14-daniele.ceraolospurio@intel.com
|
|
UAPI compatibility version 1.22.2
Resolves various bugs. Recommend newer version.
Signed-off-by: Julia Filipchuk <julia.filipchuk@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250626182805.1701096-13-daniele.ceraolospurio@intel.com
|
|
Avoid dereferencing struct drm_gem_object.import_attach for the
imported dma-buf. The dma_buf field in the GEM object instance refers
to the same buffer. Prepares to make import_attach an implementation
detail of PRIME.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250619113100.70292-3-tzimmermann@suse.de
|
|
Instead of testing import_attach for imported GEM buffers, invoke
drm_gem_is_imported() to do the test.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250619113100.70292-2-tzimmermann@suse.de
|
|
If any of the ACPI calls fail, memory allocated for the input buffer
would be leaked. Fix failure paths to free allocated memory.
Also add checks to ensure the allocations succeeded in the first place.
Reported-by: Danilo Krummrich <dakr@kernel.org>
Fixes: 176fdcbddfd2 ("drm/nouveau/gsp/r535: add support for booting GSP-RM")
Signed-off-by: Ben Skeggs <bskeggs@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://lore.kernel.org/r/20250617040036.2932-1-bskeggs@nvidia.com
|
|
The vgem driver does not need to create a platform device, as there is
no real platform resources associated it, it only did so because it was
simple to do that in order to get a device to use for resource
management of drm resources. Change the driver to use the faux device
instead as this is NOT a real platform device.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@gmail.com>
Cc: Simona Vetter <simona@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/2025070114-iron-shiny-b92e@gregkh
|
|
The vkms driver does not need to create a platform device, as there is
no real platform resources associated it, it only did so because it was
simple to do that in order to get a device to use for resource
management of drm resources. Change the driver to use the faux device
instead as this is NOT a real platform device.
Tested-by: Louis Chauvet <louis.chauvet@bootlin.com>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Cc: Simona Vetter <simona@ffwll.ch>
Cc: Melissa Wen <melissa.srw@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/2025070147-antics-pleat-edd2@gregkh
|
|
The vast majority of drivers that use GEM-SHMEM helpers do not use
an s/g table for imported buffers; specifically all drivers that use
DRM_GEM_SHMEM_DRIVER_OPS. Therefore convert the initializer macro
to DRM_GEM_SHMEM_DRIVER_OPS_NO_MAP_SGT and remove the latter. This
helps to avoid swiotbl errors, such as seen with some Aspeed systems
ast 0000:07:00.0: swiotlb buffer is full (sz: 3145728 bytes), total 32768 (slots), used 0 (slots)
The error is caused by the system's limited DMA capabilities and can
happen with any GEM-SHMEM-based driver. It results in a performance
penalty.
In the case of vgem and vkms, the devices do not support DMA at all,
which can result in failure to map the buffer object into the kernel's
address space. [1][2] Avoiding the s/g table fixes this problem.
The other drivers based on GEM-SHMEM, imagination, lima, panfrost,
panthor, v3d and virtio, use the s/g table of imported buffers. Neither
driver uses the default initializer, so they won't be affected by
this change.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: Zenghui Yu <zenghui.yu@linux.dev>
Closes: https://lore.kernel.org/dri-devel/6d22bce3-4533-4cfa-96ba-64352b715741@linux.dev/ # [1]
Reported-by: José Expósito <jose.exposito89@gmail.com>
Closes: https://lore.kernel.org/dri-devel/20250311172054.2903-1-jose.exposito89@gmail.com/ # [2]
Tested-by: Zenghui Yu <zenghui.yu@linux.dev>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://lore.kernel.org/r/20250630143537.309052-1-tzimmermann@suse.de
|
|
Commit a59a27176914 ("drm/bridge: tc358767: convert to
devm_drm_bridge_alloc() API") split tc_probe_bridge_endpoint() in two
functions, thus duplicating the loop over the endpoints in each of those
functions. However it missed duplicating the of_graph_parse_endpoint() call
which initializes the struct of_endpoint, resulting in an uninitialized
read.
Fixes: a59a27176914 ("drm/bridge: tc358767: convert to devm_drm_bridge_alloc() API")
Cc: stable@vger.kernel.org
Reported-by: Colin King (gmail) <colin.i.king@gmail.com>
Closes: https://lore.kernel.org/all/056b34c3-c1ea-4b8c-9672-c98903ffd012@gmail.com/
Reviewed-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250704-drm-bridge-alloc-fix-tc358767-regression-v2-1-ec0e511bedd0@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
|
|
devm_drm_bridge_alloc() is the new API to be used for allocating
(and partially initializing) a private driver struct embedding
a struct drm_bridge.
Analogix DP driver somehow missed the automated conversion in commit
9c399719cfb9 ("drm: convert many bridge drivers from devm_kzalloc() to
devm_drm_bridge_alloc() API"), what causes the following warning:
------------[ cut here ]------------
WARNING: lib/refcount.c:25 at drm_bridge_attach+0x2c/0x248, CPU#1: kworker/u8:1/34
refcount_t: addition on 0; use-after-free.
Modules linked in:
CPU: 1 UID: 0 PID: 34 Comm: kworker/u8:1 Not tainted 6.16.0-rc3-next-20250627-dirty #15839 PREEMPT
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x88
dump_stack_lvl from __warn+0x94/0x1f0
__warn from warn_slowpath_fmt+0x124/0x1bc
warn_slowpath_fmt from drm_bridge_attach+0x2c/0x248
drm_bridge_attach from analogix_dp_bind+0x70/0xc8
analogix_dp_bind from exynos_dp_bind+0x58/0xc4
exynos_dp_bind from component_bind_all+0x11c/0x27c
component_bind_all from exynos_drm_bind+0xe8/0x198
exynos_drm_bind from try_to_bring_up_aggregate_device+0x200/0x2d8
try_to_bring_up_aggregate_device from __component_add+0xb0/0x170
__component_add from exynos_dp_probe+0xc0/0x164
exynos_dp_probe from platform_probe+0x5c/0xb8
platform_probe from really_probe+0xe0/0x3d8
really_probe from __driver_probe_device+0x9c/0x1e0
__driver_probe_device from driver_probe_device+0x30/0xc0
driver_probe_device from __device_attach_driver+0xa8/0x120
__device_attach_driver from bus_for_each_drv+0x84/0xdc
bus_for_each_drv from __device_attach+0xb0/0x20c
__device_attach from bus_probe_device+0x8c/0x90
bus_probe_device from deferred_probe_work_func+0x98/0xe0
deferred_probe_work_func from process_one_work+0x24c/0x70c
process_one_work from worker_thread+0x1b8/0x3bc
worker_thread from kthread+0x13c/0x264
kthread from ret_from_fork+0x14/0x28
...
---[ end trace 0000000000000000 ]---
Fix this by switching the driver to the new API.
Note the above warning only appears starting with commit a7748dd127ea
("drm/bridge: get/put the bridge reference in drm_bridge_add/remove()")
which is the first commmit having added a drm_bridge_get/put() pair and
thus exposing the incorrect initial refcount issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: a7748dd127ea ("drm/bridge: get/put the bridge reference in drm_bridge_add/remove()")
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20250627165652.580798-1-m.szyprowski@samsung.com
[Luca: add Fixes tag and mention the reason in commit message]
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
|
|
This code needs to be indented one more tab.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/30b896c2-ae71-4cf2-9511-2713da7e1632@sabinyo.mountain
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Recent generations of Tegra have moved the display components outside of
host1x, leading to a device that has no CRTCs attached and hence doesn't
support any of the modesetting functionality. When this is detected, the
driver clears the DRIVER_MODESET and DRIVER_ATOMIC flags for the device.
Unfortunately, this causes the following errors during boot:
[ 15.418958] ERR KERN drm drm: [drm] *ERROR* Failed to register client: -95
[ 15.425311] WARNING KERN drm drm: [drm] Failed to set up DRM client; error -95
These originate from the fbdev client checking for the presence of the
DRIVER_MODESET flag and returning -EOPNOTSUPP. However, if a driver does
not support DRIVER_MODESET this is entirely expected and the error isn't
helpful.
Prevent this misleading error message by setting up the DRM clients only
if modesetting is enabled.
Changes in v2:
- use DRIVER_MODESET check to avoid registering any clients
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250613122838.2082334-1-thierry.reding@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
When driver is built with either CONFIG_DRM_I2C_ADV7511_AUDIO or
CONFIG_DRM_I2C_ADV7511_CEC disabled, drm_bridge_connector_init() is
expected to fail with -EINVAL. That is because all required audio (or
CEC) related callbacks in adv7511_bridge_funcs ended up being NULL.
Set DRM_BRIDGE_OP_HDMI_AUDIO and DRM_BRIDGE_OP_HDMI_CEC_ADAPTER bridge
ops only when the aforementioned kernel config options have been
enabled.
Fixes: ae01d3183d27 ("drm/bridge: adv7511: switch to the HDMI connector helpers")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250704-adv7511-bridge-ops-fix-v1-1-c1385922066e@collabora.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202507032334.9SCwc952-lkp@intel.com/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
|
|
KMS-only drivers should only allocate dumb buffers. The driver custom
ioctls are only meant for the usermode gpu driver (mesa), and not for
general consumption, so they don't make sense for standalone KMS
drivers.
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/662598/
|
|
Avoid the possibility of missing features between the split and unified
drm driver cases by defining DRIVER_FEATURES_GPU / KMS and using those
in the drm_driver initializations.
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/662595/
|
|
There are cases when we want to have separate DRM devices for GPU and
display pipelines.
One example is development, when it is beneficial to be able to bind the
GPU driver separately, without the display pipeline (and without the
hacks adding "amd,imageon" to the compatible string).
Another example is some of Qualcomm platforms, which have two MDSS
units, but only one GPU. With current approach it is next to impossible
to support this usecase properly, while separate binding allows users to
have three DRM devices: two for MDSS units and a single headless GPU.
Add kernel param msm.separate_gpu_kms, which if set to true forces
creation of separate display and GPU DRM devices. Mesa supports this
setup by using the kmsro wrapper.
The param is disabled by default, in order to be able to test userspace
for the compatibility issues. Simple clients are able to handle this
setup automatically.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/662590/
[Rob: renamed the modparam to separate_gpu_kms, and add missing
DRIVER_GEM_GPUVA]
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
|
|
Currently the msm driver creates an extra interim platform device for
Imageon GPUs. This is not ideal, as the device doesn't have
corresponding OF node. If the headless mode is used for newer GPUs, then
the msm_use_mmu() function can not detect corresponding IOMMU devices.
Also the DRM device (although it's headless) is created with modesetting
flags being set.
To solve all these issues, rework the way the Imageon devices are bound.
Remove the interim device, don't register a component and instead use a
cut-down version of the normal functions to probe or remove the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/662584/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
|
|
Move symbol selection to be more fine grained: select DP helpers only if
DP driver is also enabled, move KMS and display helpers to the newly
introduced DRM_MSM_KMS.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/662589/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
|
|
Both perf and hangrd make sense only for GPU devices. Bail out if we are
registering a KMS-only device.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/662583/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
|
