Age | Commit message (Collapse) | Author |
|
Driver needs to ensure that it doesn't mask the PM interrupts, which are
unmasked/needed by GuC firmware. For that, Driver maintains a bitmask of
interrupts to be kept unmasked, pm_intr_keep.
pm_intr_keep was determined across GuC load. GuC gets loaded in different
scenarios and it is not going to change the pm_intr_keep so this patch
moves its setup to intel_irq_init.
This patch fixes incorrect RPS masking leading to UP interrupts triggered
even when at cur_freq=max and inversly for Down interrupts.
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488862355-9768-1-git-send-email-sagar.a.kamble@intel.com
|
|
section
printks are slow so we should not be doing them from the vblank evade
critical section. These could explain why we sometimes seem to
blow past our 100 usec deadline.
The problem has been there ever since commit c331879ce8ea ("drm/i915:
skylake sprite plane scaling using shared scalers.") but it may not have
been readily visible until commit e1edbd44e23b ("drm/i915: Complain
if we take too long under vblank evasion.") increased our chances
of noticing it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1488974407-25175-1-git-send-email-maarten.lankhorst@linux.intel.com
Fixes: c331879ce8ea ("drm/i915: skylake sprite plane scaling using shared scalers")
Cc: <stable@vger.kernel.org> # v4.2+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[mlankhorst: Add missing tags, point to the correct offending commit]
|
|
If we have any residual freed atomic state from earlier commits, flush
the freed list after performing the current modeset. This prevents the
freed list from ever-growing if userspace manages to starve the kernel
threads (i.e. we are never able to run our free state worker and
eventually the system may even oom).
Fixes: 6f0f02dc56f1 ("drm/i915: Move atomic state free from out of fence release")
Testcase: igt/kms_cursor/legacy/all-pipes-single-bo
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202204741.18231-1-chris@chris-wilson.co.uk
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit ba318c61a9719577b6f451c055f364e4116874b2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
printks are slow so we should not be doing them from the vblank evade
critical section. These could explain why we sometimes seem to
blow past our 100 usec deadline.
The problem has been there ever since commit bfd16b2a23dc ("drm/i915:
Make updating pipe without modeset atomic.") but it may not have
been readily visible until commit e1edbd44e23b ("drm/i915: Complain
if we take too long under vblank evasion.") increased our chances
of noticing it.
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: bfd16b2a23dc ("drm/i915: Make updating pipe without modeset atomic.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307205419.19447-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit c3f8ad57a01a31397e5a0349a226a32f35ddc19c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Before we instantiate/pin the backing store for our use, we
can prepopulate the shmemfs filp efficiently using a write into the
pagecache. We avoid the penalty of instantiating all the pages, important
if the user is just writing to a few and never uses the object on the GPU,
and using a direct write into shmemfs allows it to avoid the cost of
retrieving a page (mostly the clear-before-use, but in theory we could
curtail swapin) before it is overwritten.
This can be extended later to provide additional specialisation for
other backends (other than shmemfs). For now it provides a defense
against very large write-only allocations from exhausting all of system
memory.
v2: Smelling fixes.
Fixes: fe115628d567 ("drm/i915: Implement pwrite without struct-mutex")
References: https://bugs.freedesktop.org/show_bug.cgi?id=99107
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307120338.7277-2-chris@chris-wilson.co.uk
(cherry picked from commit 7c55e2c5772dcf3cbacd0fa2bcfeefae416b73f7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Once the object has been truncated, it is unrecoverable. To facilitate
detection of this state store the error in obj->mm.pages.
This is required for the next patch which should be applied to v4.10
(via stable), so we also need to mark this patch for backporting. In
that regard, let's consider this to be a fix/improvement too.
v2: Avoid dereferencing the ERR_PTR when freeing the object.
Fixes: 1233e2db199d ("drm/i915: Move object backing storage manipulation to its own locking")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.10+
Link: http://patchwork.freedesktop.org/patch/msgid/20170307132031.32461-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 4e5462ee843c883790e9609cf560d88960ea4227)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This cannot be done reliably during vblank evasasion
since the color management registers are not double buffered.
The original commit that moved it always during vblank evasion was
wrong, so revert it to before vblank evasion again.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 20a34e78f0d7 ("drm/i915: Update color management during vblank evasion.")
Cc: stable@vger.kernel.org # v4.7+
Link: http://patchwork.freedesktop.org/patch/msgid/1488292128-14540-1-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 567f0792a6ad11c0c2620944b8eeb777359fb85a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
After
commit 2c7d0602c815277f7cb7c932b091288710d8aba7
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Dec 5 18:27:37 2016 +0200
drm/i915/gen9: Fix PCODE polling during CDCLK change notification
there is still one report of the CDCLK-change request timing out on a
KBL machine, see the Reference link. On that machine the maximum time
the request took to succeed was 34ms, so increase the timeout to 50ms.
v2:
- Change timeout from 100 to 50 ms to maintain the current 50 ms limit
for atomic waits in the driver. (Chris, Tvrtko)
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=99345
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1487946730-17162-1-git-send-email-imre.deak@intel.com
(cherry picked from commit 0129936ddda26afd5d9d207c4e86b2425952579f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Certain Baytrails, namely the 4 cpu core variants, have been
plaqued by spurious system hangs, mostly occurring with light loads.
Multiple bisects by various people point to a commit which changes the
reclocking strategy for Baytrail to follow its bigger brethen:
commit 8fb55197e64d ("drm/i915: Agressive downclocking on Baytrail")
There is also a review comment attached to this commit from Deepak S
on avoiding punit access on Cherryview and thus it was excluded on
common reclocking path. By taking the same approach and omitting
the punit access by not tweaking the thresholds when the hardware
has been asked to move into different frequency, considerable gains
in stability have been observed.
With J1900 box, light render/video load would end up in system hang
in usually less than 12 hours. With this patch applied, the cumulative
uptime has now been 34 days without issues. To provoke system hang,
light loads on both render and bsd engines in parallel have been used:
glxgears >/dev/null 2>/dev/null &
mpv --vo=vaapi --hwdec=vaapi --loop=inf vid.mp4
So far, author has not witnessed system hang with above load
and this patch applied. Reports from the tenacious people at
kernel bugzilla are also promising.
Considering that the punit access frequency with this patch is
considerably less, there is a possibility that this will push
the, still unknown, root cause past the triggering point on most loads.
But as we now can reliably reproduce the hang independently,
we can reduce the pain that users are having and use a
static thresholds until a root cause is found.
v3: don't break debugfs and simplification (Chris Wilson)
References: https://bugzilla.kernel.org/show_bug.cgi?id=109051
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: fritsch@xbmc.org
Cc: miku@iki.fi
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
CC: Michal Feix <michal@feix.cz>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.2+
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487166779-26945-1-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 6067a27d1f0184596d51decbac1c1fdc4acb012f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
As we track whether a vma has been inserted into the drm_mm using the
vma->flags, if we fail to bind the vma into the GTT we do not update
those bits and will attempt to reinsert the vma into the drm_mm on
future passes. To prevent that, we want to unwind i915_vma_insert() if
we fail in our attempt to bind.
Fixes: 59bfa1248e22 ("drm/i915: Start passing around i915_vma from execbuffer")
Testcase: igt/drv_selftest/live_gtt
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227122654.27651-3-chris@chris-wilson.co.uk
(cherry picked from commit 31c7effa39f21f0fea1b3250ae9ff32b9c7e1ae5)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If we cease making progress in finding matching outputs for a tiled
configuration, stop looping over the remaining unconfigured outputs.
v2: Use conn_seq (instead of pass) to only apply tile configuration on
first pass.
Fixes: b0ee9e7fa5b4 ("drm/fb: add support for tiled monitor configurations. (v2)")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: <stable@vger.kernel.org> # v3.19+
Reviewed-by: Tomasz Lis <tomasz.lis@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224114306.4400-1-chris@chris-wilson.co.uk
(cherry picked from commit 754a76591b12c88f57ad8b4ca533a5c9566a1922)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Geminilake has a third sprite plane (or fourth universal plane) that is
independent from the cursor. Make sure that for_each_plane_id_on_crtc()
is aware of that extra plane so that the watermark code takes it into
account.
Fixes: e9c9882556fc ("drm/i915/glk: Configure number of sprite planes properly")
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <drm-intel-fixes@lists.freedesktop.org>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170223071600.14356-2-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit 19c3164db457e0fc65d4501fd354506228576241)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
We wait upon jiffies, but report the time elapsed using a
high-resolution timer. This discrepancy can lead to us timing out the
wait prior to us reporting the elapsed time as complete.
This restores the squelching lost in commit e95433c73a11 ("drm/i915:
Rearrange i915_wait_request() accounting with callers").
Fixes: e95433c73a11 ("drm/i915: Rearrange i915_wait_request() accounting with callers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/20170216125441.30923-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit c1d2061b28c2aa25ec39b60d9c248e6beebd7315)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Add a selftest to exercise evicting neighbouring nodes that conflict due
to page colouring in the GTT.
v2: add a peppering of comments
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170306235414.23407-4-matthew.auld@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
It looks like we were incorrectly comparing vma->node against itself
instead of the target node, when evicting for a node on systems where we
need guard pages between regions with different cache domains. As a
consequence we can end up trying to needlessly evict neighbouring nodes,
even if they have the same cache domain, and if they were pinned we
would fail the eviction.
Fixes: 625d988acc28 ("drm/i915: Extract reserving space in the GTT to a helper")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170306235414.23407-3-matthew.auld@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
For our fake dma objects we can leak the underlying gem object if we
fail to pin our "backing storage".
[ 39.952618] =============================================================================
[ 39.952625] BUG mock_object (Tainted: G U ): Objects remaining in mock_object on __kmem_cache_shutdown()
[ 39.952629] -----------------------------------------------------------------------------
[ 39.952633] Disabling lock debugging due to kernel taint
[ 39.952635] INFO: Slab 0xffffea00086c6a00 objects=21 used=1 fp=0xffff88021b1abc00 flags=0x5fff8000008100
[ 39.952640] CPU: 1 PID: 1258 Comm: drv_selftest Tainted: G BU 4.10.0+ #46
[ 39.952641] Hardware name: Apple Inc. MacBookPro11,1/Mac-189A3D4F975D5FFC, BIOS MBP111.88Z.0138.B17.1602221718 02/22/2016
[ 39.952642] Call Trace:
[ 39.952648] dump_stack+0x4d/0x6f
[ 39.952651] slab_err+0x9d/0xb0
[ 39.952654] ? ksm_migrate_page+0xe0/0xe0
[ 39.952657] ? on_each_cpu_cond+0x9a/0xc0
[ 39.952658] ? __kmalloc+0x1af/0x1c0
[ 39.952660] ? __kmem_cache_shutdown+0x173/0x3e0
[ 39.952661] __kmem_cache_shutdown+0x196/0x3e0
[ 39.952664] kmem_cache_destroy+0xa0/0x150
[ 39.952708] mock_device_release+0x113/0x140 [i915]
[ 39.952726] drm_dev_release+0x20/0x40 [drm]
[ 39.952735] drm_dev_unref+0x23/0x30 [drm]
[ 39.952768] i915_gem_gtt_mock_selftests+0x55/0x70 [i915]
[ 39.952803] __run_selftests+0x169/0x1c0 [i915]
[ 39.952805] ? 0xffffffffa0151000
[ 39.952840] i915_mock_selftests+0x30/0x60 [i915]
[ 39.952869] i915_init+0xc/0x78 [i915]
[ 39.952870] ? 0xffffffffa0151000
[ 39.952872] do_one_initcall+0x43/0x170
[ 39.952874] ? __vunmap+0x81/0xd0
[ 39.952875] ? kmem_cache_alloc_trace+0x37/0x170
[ 39.952877] ? do_init_module+0x27/0x1f8
[ 39.952879] do_init_module+0x5f/0x1f8
[ 39.952881] load_module+0x2423/0x29b0
[ 39.952882] ? __symbol_put+0x40/0x40
[ 39.952885] ? kernel_read_file+0x1a3/0x1c0
[ 39.952887] SYSC_finit_module+0xbc/0xf0
[ 39.952889] SyS_finit_module+0xe/0x10
[ 39.952892] entry_SYSCALL_64_fastpath+0x13/0x94
v2: use onion teardown and favour i915_gem_object_put
Fixes: 8d28ba4568f4 ("drm/i915: Exercise filling the top/bottom portions of the ppgtt")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170306235414.23407-2-matthew.auld@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so it's not necessary to call drm_debugfs_remove_files().
Cc: airlied@linux.ie
Cc: kraxel@redhat.com
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307204924.1002-4-noralf@tronnes.org
[ kraxel: solved conflict ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
If we allow the user to convert a GTT mmap address into a userptr, we
may end up in recursion hell, where currently we hit a mutex deadlock
but other possibilities include use-after-free during the
unbind/cancel_userptr.
[ 143.203989] gem_userptr_bli D 0 902 898 0x00000000
[ 143.204054] Call Trace:
[ 143.204137] __schedule+0x511/0x1180
[ 143.204195] ? pci_mmcfg_check_reserved+0xc0/0xc0
[ 143.204274] schedule+0x57/0xe0
[ 143.204327] schedule_timeout+0x383/0x670
[ 143.204374] ? trace_hardirqs_on_caller+0x187/0x280
[ 143.204457] ? trace_hardirqs_on_thunk+0x1a/0x1c
[ 143.204507] ? usleep_range+0x110/0x110
[ 143.204657] ? irq_exit+0x89/0x100
[ 143.204710] ? retint_kernel+0x2d/0x2d
[ 143.204794] ? trace_hardirqs_on_caller+0x187/0x280
[ 143.204857] ? _raw_spin_unlock_irq+0x33/0x60
[ 143.204944] wait_for_common+0x1f0/0x2f0
[ 143.205006] ? out_of_line_wait_on_atomic_t+0x170/0x170
[ 143.205103] ? wake_up_q+0xa0/0xa0
[ 143.205159] ? flush_workqueue_prep_pwqs+0x15a/0x2c0
[ 143.205237] wait_for_completion+0x1d/0x20
[ 143.205292] flush_workqueue+0x2e9/0xbb0
[ 143.205339] ? flush_workqueue+0x163/0xbb0
[ 143.205418] ? __schedule+0x533/0x1180
[ 143.205498] ? check_flush_dependency+0x1a0/0x1a0
[ 143.205681] i915_gem_userptr_mn_invalidate_range_start+0x1c7/0x270 [i915]
[ 143.205865] ? i915_gem_userptr_dmabuf_export+0x40/0x40 [i915]
[ 143.205955] __mmu_notifier_invalidate_range_start+0xc6/0x120
[ 143.206044] ? __mmu_notifier_invalidate_range_start+0x51/0x120
[ 143.206123] zap_page_range_single+0x1c7/0x1f0
[ 143.206171] ? unmap_single_vma+0x160/0x160
[ 143.206260] ? unmap_mapping_range+0xa9/0x1b0
[ 143.206308] ? vma_interval_tree_subtree_search+0x75/0xd0
[ 143.206397] unmap_mapping_range+0x18f/0x1b0
[ 143.206444] ? zap_vma_ptes+0x70/0x70
[ 143.206524] ? __pm_runtime_resume+0x67/0xa0
[ 143.206723] i915_gem_release_mmap+0x1ba/0x1c0 [i915]
[ 143.206846] i915_vma_unbind+0x5c2/0x690 [i915]
[ 143.206925] ? __lock_is_held+0x52/0x100
[ 143.207076] i915_gem_object_set_tiling+0x1db/0x650 [i915]
[ 143.207236] i915_gem_set_tiling_ioctl+0x1d3/0x3b0 [i915]
[ 143.207377] ? i915_gem_set_tiling_ioctl+0x5/0x3b0 [i915]
[ 143.207457] drm_ioctl+0x36c/0x670
[ 143.207535] ? debug_lockdep_rcu_enabled.part.0+0x1a/0x30
[ 143.207730] ? i915_gem_object_set_tiling+0x650/0x650 [i915]
[ 143.207793] ? drm_getunique+0x120/0x120
[ 143.207875] ? __handle_mm_fault+0x996/0x14a0
[ 143.207939] ? vm_insert_page+0x340/0x340
[ 143.208028] ? up_write+0x28/0x50
[ 143.208086] ? vm_mmap_pgoff+0x160/0x190
[ 143.208163] do_vfs_ioctl+0x12c/0xa60
[ 143.208218] ? debug_lockdep_rcu_enabled+0x35/0x40
[ 143.208267] ? ioctl_preallocate+0x150/0x150
[ 143.208353] ? __do_page_fault+0x36a/0x6e0
[ 143.208400] ? mark_held_locks+0x23/0xc0
[ 143.208479] ? up_read+0x1f/0x40
[ 143.208526] ? entry_SYSCALL_64_fastpath+0x5/0xc6
[ 143.208669] ? __fget_light+0xa7/0xc0
[ 143.208747] SyS_ioctl+0x41/0x70
To prevent the possibility of a deadlock, we defer scheduling the worker
until after we have proven that given the current mm, the userptr range
does not overlap a GGTT mmaping. If another thread tries to remap the
GGTT over the userptr before the worker is scheduled, it will be stopped
by its invalidate-range flushing the current work, before the deadlock
can occur.
v2: Improve discussion of how we end up in the deadlock.
v3: Don't forget to mark the userptr as active after a successful
gup_fast. Rename overlaps_ggtt to noncontiguous_or_overlaps_ggtt.
v4: Fix test ordering between invalid GTT mmaping and range completion
(Tvrtko)
Reported-by: Michał Winiarski <michal.winiarski@intel.com>
Testcase: igt/gem_userptr_blits/map-fixed-invalidate-gup
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308215903.24171-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
To avoid waiting for work from other invalidate-range threads where
not required, only wait on the userptr cancel workqueue if we have added
some work to it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307205851.32578-2-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
If the worker fails, it no longer has pages to release and can be
immediately removed from the invalidate-tree.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307205851.32578-1-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
The trouble here is that looking at all connector->state in the
verifier isn't good, because that's run from the commit work, which
doesn't hold the connection_mutex. Which means we're only allowed to
look at states in our atomic update.
The simple fix for future proofing would be to switch over to
drm_for_each_connector_in_state, but that has the problem that the
verification then fails if not all connectors are in the state. And we
also need to be careful to check both old and new encoders, and not
screw things up when an encoder gets reassigned.
Note that this isn't the full fix, since we still look at
connector->state. To fix that, we need Maarten's patch series to
switch over to state pointers within drm_atomic_state, but that's a
different series.
v2: Use oldnew iterator (Maarten).
v3: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-6-daniel.vetter@ffwll.ch
|
|
This gets rid of the last users of for_each_intel_connector(), remove
that too.
At first I wasn't sure whether the 2 loops in the modeset state
checker should instead only loop over the connectors in the atomic
commit. But we never add connectors to an atomic update if they don't
(or won't have) a CRTC assigned, which means there'd be a gap in check
coverage. Hence loop over everything on those too.
v2: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-5-daniel.vetter@ffwll.ch
|
|
Drive-by fixup while looking at all the connector_list walkers -
holding connection_mutex does actually _not_ give you locking to look
at the legacy drm_connector->encoder->crtc pointer chain. That one is
solely owned by the atomic commit workers. Instead we must inspect the
atomic state.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-4-daniel.vetter@ffwll.ch
|
|
One case where I nuked a now unecessary locking, otherwise all just
boring stuff.
v2: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-3-daniel.vetter@ffwll.ch
|
|
Nothing special, just rote conversion.
v2: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-2-daniel.vetter@ffwll.ch
|
|
While at it also try to reduce the locking a bit to what's really just
needed instead of everything that we could possibly lock.
Added a new for_each_intel_connector_iter which includes the cast to
intel_connector.
Otherwise just plain transformation with nothing special going on.
v2: Review from Maarten:
- Stick with modeset_lock_all in sink_crc, it looks at crtc->state.
- Fix up early loop exit in i915_displayport_test_active_write.
v3: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-1-daniel.vetter@ffwll.ch
|
|
Signed-off-by: Jim Qu <Jim.Qu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
__i915_gem_request_started() asserts that the seqno is valid, but
i915_spin_request() was not checking before querying whether the request
had started.
Reported-by: Michał Winiarski <michal.winiarski@intel.com>
Fixes: 754c9fd57649 ("drm/i915: Protect the request->global_seqno with the engine->timeline lock")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308142238.22994-1-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
i915_gem_object_is_dead() was a temporary lockdep aide whilst
transitioning to a new locking structure for obj->mm. Since commit
1233e2db199d ("drm/i915: Move object backing storage manipulation to its
own locking") it is now unused and should be removed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308132629.7987-2-chris@chris-wilson.co.uk
|
|
We have to avoid taking ww_mutex inside the shrinker as we use it as a
plain mutex type and so need to avoid recursive deadlocks:
[ 602.771969] =================================
[ 602.771970] [ INFO: inconsistent lock state ]
[ 602.771973] 4.10.0gpudebug+ #122 Not tainted
[ 602.771974] ---------------------------------
[ 602.771975] inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
[ 602.771978] kswapd0/40 [HC0[0]:SC0[0]:HE1:SE1] takes:
[ 602.771979] (reservation_ww_class_mutex){+.+.?.}, at: [<ffffffffa054680a>] i915_gem_object_wait+0x39a/0x410 [i915]
[ 602.772020] {RECLAIM_FS-ON-W} state was registered at:
[ 602.772024] mark_held_locks+0x76/0x90
[ 602.772026] lockdep_trace_alloc+0xb8/0xc0
[ 602.772028] __kmalloc_track_caller+0x5d/0x130
[ 602.772031] krealloc+0x89/0xb0
[ 602.772033] reservation_object_reserve_shared+0xaf/0xd0
[ 602.772055] i915_gem_do_execbuffer.isra.35+0x1413/0x18b0 [i915]
[ 602.772075] i915_gem_execbuffer2+0x10e/0x1d0 [i915]
[ 602.772078] drm_ioctl+0x291/0x480
[ 602.772079] do_vfs_ioctl+0x695/0x6f0
[ 602.772081] SyS_ioctl+0x3c/0x70
[ 602.772084] entry_SYSCALL_64_fastpath+0x18/0xad
[ 602.772085] irq event stamp: 5197423
[ 602.772088] hardirqs last enabled at (5197423): [<ffffffff8116751d>] kfree+0xdd/0x170
[ 602.772091] hardirqs last disabled at (5197422): [<ffffffff811674f9>] kfree+0xb9/0x170
[ 602.772095] softirqs last enabled at (5190992): [<ffffffff8107bfe1>] __do_softirq+0x221/0x280
[ 602.772097] softirqs last disabled at (5190575): [<ffffffff8107c294>] irq_exit+0x64/0xc0
[ 602.772099]
other info that might help us debug this:
[ 602.772100] Possible unsafe locking scenario:
[ 602.772101] CPU0
[ 602.772101] ----
[ 602.772102] lock(reservation_ww_class_mutex);
[ 602.772104] <Interrupt>
[ 602.772105] lock(reservation_ww_class_mutex);
[ 602.772107]
*** DEADLOCK ***
[ 602.772109] 2 locks held by kswapd0/40:
[ 602.772110] #0: (shrinker_rwsem){++++..}, at: [<ffffffff811337b5>] shrink_slab.constprop.62+0x35/0x280
[ 602.772116] #1: (&dev->struct_mutex){+.+.+.}, at: [<ffffffffa0553957>] i915_gem_shrinker_lock+0x27/0x60 [i915]
[ 602.772141]
stack backtrace:
[ 602.772144] CPU: 2 PID: 40 Comm: kswapd0 Not tainted 4.10.0gpudebug+ #122
[ 602.772145] Hardware name: LENOVO 42433ZG/42433ZG, BIOS 8AET64WW (1.44 ) 07/26/2013
[ 602.772147] Call Trace:
[ 602.772151] dump_stack+0x68/0xa1
[ 602.772153] print_usage_bug+0x1d4/0x1f0
[ 602.772155] mark_lock+0x390/0x530
[ 602.772157] ? print_irq_inversion_bug+0x200/0x200
[ 602.772159] __lock_acquire+0x405/0x1260
[ 602.772181] ? i915_gem_object_wait+0x39a/0x410 [i915]
[ 602.772183] lock_acquire+0x60/0x80
[ 602.772205] ? i915_gem_object_wait+0x39a/0x410 [i915]
[ 602.772207] mutex_lock_nested+0x69/0x760
[ 602.772229] ? i915_gem_object_wait+0x39a/0x410 [i915]
[ 602.772231] ? kfree+0xdd/0x170
[ 602.772253] ? i915_gem_object_wait+0x163/0x410 [i915]
[ 602.772255] ? trace_hardirqs_on_caller+0x18d/0x1c0
[ 602.772256] ? trace_hardirqs_on+0xd/0x10
[ 602.772278] i915_gem_object_wait+0x39a/0x410 [i915]
[ 602.772300] i915_gem_object_unbind+0x5e/0x130 [i915]
[ 602.772323] i915_gem_shrink+0x22d/0x3d0 [i915]
[ 602.772347] i915_gem_shrinker_scan+0x3f/0x80 [i915]
[ 602.772349] shrink_slab.constprop.62+0x1ad/0x280
[ 602.772352] shrink_node+0x52/0x80
[ 602.772355] kswapd+0x427/0x5c0
[ 602.772358] kthread+0x122/0x130
[ 602.772360] ? try_to_free_pages+0x270/0x270
[ 602.772362] ? kthread_stop+0x70/0x70
[ 602.772365] ret_from_fork+0x2e/0x40
v2: Add commentary about the pruning being opportunistic
Reported-by: Jan Nordholz <jckn@gmx.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99977#c10
Fixes: e54ca9774777 ("drm/i915: Remove completed fences after a wait")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308132629.7987-1-chris@chris-wilson.co.uk
|
|
DRM_UT_CORE generates way too much noise usually, so having the
framebuffer init failures use DRM_UT_CORE is a pain when trying to
find out the reason why you failed in creating a framebuffer.
Let's use DRM_UT_KMS for these debug messages instead.
v2: s/at less than/at most/ in the debug message (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-6-ville.syrjala@linux.intel.com
|
|
intel_fill_fb_info() should pass the correct plane index to
_intel_compute_tile_offset() once we start to care about the AUX
surface.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-5-ville.syrjala@linux.intel.com
|
|
To make life easier let's allow skl_plane_stride() to be called for the
AUX surface even when there is no AUX surface. Avoids special cases in
the callers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-4-ville.syrjala@linux.intel.com
|
|
Let's try to keep the alignment requirements in one place, and so
towards that end let's move the AUX_DIST alignment handling into
intel_surf_alignment() alongside the main surface alignment stuff.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-3-ville.syrjala@linux.intel.com
|
|
Now that framebuffers can be used even before calling
drm_framebuffer_init() we can start to plumb them into more places,
instead of passing individual pieces for fb metadata.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-2-ville.syrjala@linux.intel.com
|
|
under virtualization enviroment, it is possible guest update pipe
registers across vblank intervals due to overhead of mmio traps or vm
schedule out. However, it is safe since those pipe update happen in
virual registers and will not be committed to hardware. suppress that
atomic commit error message under virtualization case to avoid
confusing user.
v2: per ville's comment: return early and against Maarten's patch
v3: coding style clean
Signed-off-by: Bing Niu <bing.niu@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489004043-15449-1-git-send-email-bing.niu@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
printks are slow so we should not be doing them from the vblank evade
critical section. These could explain why we sometimes seem to
blow past our 100 usec deadline.
The problem has been there ever since commit bfd16b2a23dc ("drm/i915:
Make updating pipe without modeset atomic.") but it may not have
been readily visible until commit e1edbd44e23b ("drm/i915: Complain
if we take too long under vblank evasion.") increased our chances
of noticing it.
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: bfd16b2a23dc ("drm/i915: Make updating pipe without modeset atomic.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307205419.19447-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
Remove the .debugfs_cleanup() callback now that all the users are gone.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307204924.1002-3-noralf@tronnes.org
|
|
Move the contents of msm_debugfs_cleanup() to msm_drm_uninit() to free
up the drm_driver->debugfs_cleanup callback. Also remove the
mdp_kms_funcs->debugfs_cleanup callback which has no users.
Cc: robdclark@gmail.com
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307204924.1002-2-noralf@tronnes.org
|
|
drm-intel-fixes
gvt-fixes-2017-03-08
- MMIO cmd access flag cleanup
- Virtual display fixes from Weinan and Bing
- config space reset fix from Changbin
- better workload submission error path fix from Chuanxiao
- other misc fixes
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Backmerge drm-next to get at all the good stuff in drm-misc. We need
that because:
- drm_connector_list_iter conversion for i915 needs the core patches.
- Maarten's patches to use the new atomic state iterators also need
the core patches.
- We need the new link status property to complete the DP retraining
work, merging through 2 branches wasn't a good idea and we had to
partially backtrack.
- Chris needs reservation_object_trylock and we want to roll out
kref_read everywhere.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
drm-intel-fixes
gvt-next-2017-02-24
- Min's vGPU failsafe to guard against non-secured guest
- Some guest warning fix and host error message cleanup
- Fixed vGPU type refinement for usability issue
- environ string fix from Takashi Iwai
- one kernel oops fix from Chuanxiao
- other misc fixes
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
- Re-architecture of the code to handle proprietary fw, more abstracted
to support the multitude of differences that NVIDIA introduce
- Support in the said code for GP10x ACR and GR fw, giving acceleration
support \o/
- Fix for GTX 970 GPUs that are in an odd MMU configuration
* 'linux-4.12' of git://github.com/skeggsb/linux: (60 commits)
drm/nouveau/fb/gf100-: rework ram detection
drm/nouveau/fb/gm200: split ram implementation from gm107
drm/nouveau/fb/gf108: split implementation from gf100
drm/nouveau/fb/gf100-: modify constructors to allow more customisation
drm/nouveau/kms/nv50: use drm core i2c-over-aux algorithm
drm/nouveau/i2c/g94-: return REPLY_M value on reads
drm/nouveau/i2c: modify aux interface to return length actually transferred
drm/nouveau/gp10x: enable secboot and GR
drm/nouveau/gr/gp102: initial support
drm/nouveau/falcon: support for gp10x msgqueue
drm/nouveau/secboot: add gp102/gp104/gp106/gp107 support
drm/nouveau/secboot: put HS code loading code into own file
drm/nouveau/secboot: support for r375 ACR
drm/nouveau/secboot: support for r367 ACR
drm/nouveau/secboot: support for r364 ACR
drm/nouveau/secboot: workaround bug when starting SEC2 firmware
drm/nouveau/secboot: support standard NVIDIA HS binaries
drm/nouveau/secboot: support for unload blob bootloader
drm/nouveau/secboot: let callers interpret return value of blobs
drm/nouveau/secboot: support for different load and unload falcons
...
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-next
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
|
|
gvt_err should be used for dumping error message. This patch changes
some gvt_err to gvt_dbg_cmd, as they are only debugging message, not
errors.
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Gabriel Krisman reported these warnings when building the documentation:
./drivers/gpu/drm/drm_dp_helper.c:1165: warning: No description found
for parameter 'crtc'
./drivers/gpu/drm/drm_dp_helper.c:1166: warning: No description found
for parameter 'crtc'
Reported-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307203511.14258-1-tomeu.vizoso@collabora.com
|
|
Before we instantiate/pin the backing store for our use, we
can prepopulate the shmemfs filp efficiently using a write into the
pagecache. We avoid the penalty of instantiating all the pages, important
if the user is just writing to a few and never uses the object on the GPU,
and using a direct write into shmemfs allows it to avoid the cost of
retrieving a page (mostly the clear-before-use, but in theory we could
curtail swapin) before it is overwritten.
This can be extended later to provide additional specialisation for
other backends (other than shmemfs). For now it provides a defense
against very large write-only allocations from exhausting all of system
memory.
v2: Smelling fixes.
Fixes: fe115628d567 ("drm/i915: Implement pwrite without struct-mutex")
References: https://bugs.freedesktop.org/show_bug.cgi?id=99107
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307120338.7277-2-chris@chris-wilson.co.uk
|
|
Once the object has been truncated, it is unrecoverable. To facilitate
detection of this state store the error in obj->mm.pages.
This is required for the next patch which should be applied to v4.10
(via stable), so we also need to mark this patch for backporting. In
that regard, let's consider this to be a fix/improvement too.
v2: Avoid dereferencing the ERR_PTR when freeing the object.
Fixes: 1233e2db199d ("drm/i915: Move object backing storage manipulation to its own locking")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.10+
Link: http://patchwork.freedesktop.org/patch/msgid/20170307132031.32461-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Move the {skl,bxt}_{i,uni}nit_cdclk declarations to the place where
the intel_cdclk.c functions are declared since these functions have
moved there.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487712207-17181-1-git-send-email-paulo.r.zanoni@intel.com
|
|
The IS_G4X macro is defined as IS_G45 || IS_GM45. We have two points
in our code where we have an if statement checking for GM45 followed
by an else if statement checking for IS_G4X. This can be confusing
since the IS_G4X check won't be catching the previously-checked GM45.
Someone quickly trying to check which functions run on each platform
may end up getting confused while reading the code.
Fix the potential confusion by limiting the else if statements to only
check for the platform that was not already checked earlier in the if
ladder.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487620842-22893-3-git-send-email-paulo.r.zanoni@intel.com
|