| Age | Commit message (Collapse) | Author |
|---|
|
When the SOR is disabled in DP mode as part of an unplug event, do not
attempt to power the DP link down. Powering down the link requires the
DPAUX to transmit AUX messages which only works if there's a connected
sink.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SOR0 on Tegra210 does, contrary to what was previously assumed, in
fact support DisplayPort. The difference between SOR0 and SOR1 is that
the latter supports audio and HDCP over DP, whereas the former doesn't.
The code for eDP and DP is now almost identical and the differences can
easily be parameterized based on the presence of a panel. There is no
need any longer to duplicate the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The correct I/O pad needs to be powered up before DP can be used. Make
sure the correct default is set for Tegra generations where the I/O pad
cannot be derived from the SOR instance.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
With the clocks modelled consistently across SoC generations, the clock
setup for eDP, HDMI and DP can now be unified.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Reuse parameters from earlier generations to support DisplayPort on
Tegra194.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The connector type detection code is duplicated in two places. Keeping
both places in sync is an extra maintenance burden that can be avoided
by comparing the connector type operations that are set upon the first
detection.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
So far the pad clock was only needed on the second SOR instance. The
clock does exist for all SOR instances, though, so make sure it is
always implemented. This prepares for further unification of the code
in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The device tree bindings for the Tegra210 SOR don't require the
controller instance to be defined, since the instance can be derived
from the compatible string. The index is never used on Tegra210, so we
got away with it not getting set. However, subsequent patches will
change that, so make sure the proper index is used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
It turns out that SOR1 is just another instance of the same block as the
SOR0, so there is no need to distinguish them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add support for regular DisplayPort on Tegra210 and Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SOR found on Tegra SoCs does not support all the rates potentially
advertised by eDP 1.4. Make sure that the rates that are not supported
are filtered out.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Rework eDP code to correspond more closely to what's documented. This
also improves the reliability of modesets.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This is necessary for the output abstraction to retrieve a list of valid
modes from the EDID of a connected panel/monitor. This will be useful in
conjunction with DisplayPort support that will be added in a subsequent
patch, so that the driver can read EDID via the AUX channel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Make use of the DP link training helpers to implement full and fast link
training. While at it, refactor some of the code and remove various code
sequences that are not necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Rather than storing capabilities as flags in an integer, use a separate
boolean per capability. This simplifies the code that checks for these
capabilities.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Store capabilities in max_* fields and add separate fields for the
currently selected settings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The hardware is not guaranteed to be enabled during execution of the
tegra_sor_init() function, which can lead to a crash on some Tegra SoCs.
Fix this by moving all register programming into code that is guaranteed
to only be executed when the hardware is enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
During the discussion of patches that enhance the drm_dp_link helpers it
was concluded that these helpers aren't very useful to begin with. After
all other drivers have been converted not to use these helpers anymore,
move these helpers into the last remaining user: Tegra DRM.
If at some point these helpers are deemed more widely useful, they can
be moved out into the DRM DP helpers again.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191021143437.1477719-14-thierry.reding@gmail.com
|
|
Drop use of the deprecated drmP.h header file.
For all touched files divide include files into blocks,
and sort them within the blocks.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190804094132.29463-3-sam@ravnborg.org
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
By implementing the acquire/release protocol, the SOR reset can be
shared with other drivers that also adhere to this protocol, such as the
PMC driver that uses the same reset as part of the powergate and -ungate
implementation using generic power domains.
Runtime PM makes sure that the operations are executed in the right
order, and the reset core has error handling and WARNs in place to make
sure the acquire/release protocol is followed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.1-rc1
This set of changes starts of with some refactoring of the CEC support
to make it reusable on Tegra210 and later. Following are a couple of
fixes for HDMI audio support (via HDA).
The bulk here is a set of preparatory patches working towards enabling
Tegra186 support for host1x and VIC. Additional patches will be needed
to fully enable this, but they're not quite ready yet.
To round things off, this also adds support for configuring the SOR
crossbar using device tree, and fixes a couple of job-related issues in
the host1x code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208144721.25830-1-thierry.reding@gmail.com
|
|
The crossbar configuration is usually the same across all designs for a
given SoC generation. But sometimes there are designs that require some
other configuration.
Implement support for parsing the crossbar configuration from a device
tree. If the crossbar configuration is not present in the device tree,
fall back to the default crossbar configuration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This code can be reused for HDMI, so extract it into a reusable
function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The HDA format data passed to the SOR from the HDA codec contains more
information than just the rate and number of channels. Parse all the
fields and store them in an internal structure for subsequent use.
While at it, also fix an off-by-one error in the number of channels.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
drm-next has been forwarded to 5.0-rc1, and we need it to apply the damage
helper for dirtyfb series from Noralf Trønnes.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Make life easier for drivers by simply passing the connector
to drm_hdmi_avi_infoframe_from_display_mode() and
drm_hdmi_avi_infoframe_quant_range(). That way drivers don't
need to worry about is_hdmi2_sink mess.
v2: Make is_hdmi2_sink() return true for sil-sii8620
Adapt to omap/vc4 changes
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-1-ville.syrjala@linux.intel.com
|
|
If the SOR is already up and running when the kernel driver is probed,
setting a mode will typically fail. This can be seen for example on
Jetson TX2. Under certain circumstances the generic power domain code
will cause the SOR to be reset. However, if the power domain is never
powered off (this can happen if the HDA controller is enabled, which
is part of the same power domain as the SOR), then the SOR will end up
not getting reset and fail to properly set a mode.
To work around this, try to get the reset control and assert/deassert
it, irrespective of whether or not a generic power domain is attached
to the SOR. On platforms where the kernel implements generic power
domains (up to Tegra210) this will fail, because the power domain will
already have acquired an exclusive reference to the reset control. But
on recent platforms there the BPMP provides an ABI to control power
domains, it's possible to acquire the reset control from SOR and use
it to put the SOR into a known good state at probe time.
The proper solution for this is to make the SOR driver capable of
dealing with hardware that's already up and running (by first grace-
fully shutting it down, or perhaps by seamlessly transitioning to the
kernel driver and taking over the running display configuration). That
is fairly involved, though, so we'll go with this quickfix for now.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Remove the temporary workaround of storing the Tegra186 HDMI/DP I/O pad
ID in the SOR driver. The definition has long been available in the
soc/tegra/pmc.h header file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This code is very similar to the audio over HDMI support on older chips.
Interoperation with the audio codec is done via a pair of codec scratch
registers and an interrupt that is raised at the SOR when the codec has
written those registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SOR implemented in Tegra194 is subtly different from its predecessor
found in Tegra186. Most notably some registers have been moved around so
it is no longer compatible.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Again to align with the usual prefix of just drm_connector_. Again
done with sed + manual fixup for indent issues.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-7-daniel.vetter@ffwll.ch
|
|
Linux 4.15-rc8
Daniel requested this for so the intel CI won't fall over on drm-next
so often.
|
|
The SOR0 found on Tegra124 and Tegra210 only supports eDP and LVDS and
therefore has a slightly different clock tree than the SOR1 which does
not support eDP, but HDMI and DP instead.
Commit e1335e2f0cfc ("drm/tegra: sor: Reimplement pad clock") breaks
setups with eDP because the sor->clk_out clock is uninitialized and
therefore setting the parent clock (either the safe clock or either of
the display PLLs) fails, which can cause hangs later on since there is
no clock driving the module.
Fix this by falling back to the module clock for sor->clk_out on those
setups. This guarantees that the module will always be clocked by an
enabled clock and hence prevents those hangs.
Fixes: e1335e2f0cfc ("drm/tegra: sor: Reimplement pad clock")
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Traditionally, windows were accessed indirectly, through a register
selection window that required a global register to be programmed with
the index of the window to access. Since the global register could be
written from modesetting functions as well as the interrupt handler
concurrently, accesses had to be serialized using a lock. Using direct
accesses to the window registers the lock can be avoided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
In addition to using the SCDC helpers to enable support for scrambling
for HDMI 2.0 modes, take into account the high pixel clocks when
programming some of the registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SOR found on Tegra186 is very similar to the one found on Tegra210
and earlier. However, due to some changes in the display architecture,
some programming sequences have changed and some register have moved
around.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Future Tegra generations have an increased number of display controllers
that can drive individual SORs. In order to support that, the offset and
layout of some registers has changed in backwards-incompatible ways. Use
parameterized register offsets to support this.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The ->late_register() and ->early_unregister() callbacks are called at
the right time to make sure userspace only accesses interfaces when it
should. Move debugfs registration and unregistration to these callback
functions to avoid potential races with userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Rather create new files within the top-level DRM device's debugfs node,
add the SOR specific files to the connector's debugfs node. This avoids
the need to come up with subdirectory names and is also more intuitive.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
After commit 932f6529139e ("drm/tegra: sor: Trace register accesses"),
the debugfs register dump implementation causes excessive stack usage
and can result in build warnings. To fix this, move the register
definitions into a table and iterate over the table while dumping the
registers to debugfs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The current implementation of the pad clock isn't quite correct. This
has the side-effect of being incompatible with the implementation for
Tegra186 (provided by the BPMP) and therefore would require a massive
change to the driver to cope with the differences. Instead, simply do
what Tegra186 does and add some code to fallback to the old behaviour
for existing device trees.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.14-rc1
This contains a couple of fixes and improvements for host1x, with some
preparatory work for Tegra186 support.
The remainder is cleanup and minor bugfixes for Tegra DRM along with
enhancements to debuggability.
There have also been some enhancements to the kernel interfaces for
host1x job submissions and support for mmap'ing PRIME buffers directly,
all of which get the interfaces very close to ready for serious work.
* tag 'drm/tegra/for-4.14-rc1' of git://anongit.freedesktop.org/tegra/linux: (21 commits)
drm/tegra: Prevent BOs from being freed during job submission
drm/tegra: gem: Implement mmap() for PRIME buffers
drm/tegra: Support render node
drm/tegra: sor: Trace register accesses
drm/tegra: dpaux: Trace register accesses
drm/tegra: dsi: Trace register accesses
drm/tegra: hdmi: Trace register accesses
drm/tegra: dc: Trace register accesses
drm/tegra: sor: Use unsigned int for register offsets
drm/tegra: hdmi: Use unsigned int for register offsets
drm/tegra: dsi: Use unsigned int for register offsets
drm/tegra: dpaux: Use unsigned int for register offsets
drm/tegra: dc: Use unsigned int for register offsets
drm/tegra: Fix NULL deref in debugfs/iova
drm/tegra: switch to drm_*_get(), drm_*_put() helpers
drm/tegra: Set MODULE_FIRMWARE for the VIC
drm/tegra: Add CONFIG_OF dependency
gpu: host1x: Support sub-devices recursively
gpu: host1x: fix error return code in host1x_probe()
gpu: host1x: Fix bitshift/mask multipliers
...
|
|
Add tracepoint events for SOR controller register accesses.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Register offsets are usually fairly small numbers, so an unsigned int is
more than enough to represent them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
|
|
HDMI 1.4b support the CEA video modes as per range of CEA-861-D (VIC 1-64).
For any other mode, the VIC filed in AVI infoframes should be 0.
HDMI 2.0 sinks, support video modes range as per CEA-861-F spec, which is
extended to (VIC 1-107).
This patch adds a bool input variable, which indicates if the connected
sink is a HDMI 2.0 sink or not. This will make sure that we don't pass a
HDMI 2.0 VIC to a HDMI 1.4 sink.
This patch touches all drm drivers, who are callers of this function
drm_hdmi_avi_infoframe_from_display_mode but to make sure there is
no change in current behavior, is_hdmi2 is kept as false.
In case of I915 driver, this patch:
- checks if the connected display is HDMI 2.0.
- HDMI infoframes carry one of this two type of information:
- VIC for 4K modes for HDMI 1.4 sinks
- S3D information for S3D modes
As CEA-861-F has already defined VICs for 4K videomodes, this
patch doesn't allow sending HDMI infoframes for HDMI 2.0 sinks,
until the mode is 3D.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
PS: This patch touches a few lines in few files, which were
already above 80 char, so checkpatch gives 80 char warning again.
- gpu/drm/omapdrm/omap_encoder.c
- gpu/drm/i915/intel_sdvo.c
V2: Rebase, Added r-b from Andrzej
V3: Addressed review comment from Ville:
- Do not send VICs in both AVI-IF and HDMI-IF
send only one of it.
V4: Rebase
V5: Added r-b from Neil.
Addressed review comments from Ville
- Do not block HDMI vendor IF, instead check for VIC while
handling AVI infoframes
V6: Rebase
V7: Rebase
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499960000-9232-2-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
Memory for the brick clock is allocated by devm_kzalloc(), so there is
no need here to free it explicitly.
The only function that calls tegra_clk_sor_brick_register() is the probe
function and it correctly checks and handles the return value, which, on
failure, will cause devm_ allocated memory to be freed automatically.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.8-rc1
This set of changes contains a bunch of cleanups to the host1x driver as
well as the addition of a pin controller for DPAUX, which is required by
boards to configure the DPAUX pads in AUX mode (for DisplayPort) or I2C
mode (for HDMI and DDC).
Included is also a bit of rework of the SOR driver in preparation to add
DisplayPort support as well as some refactoring and cleanup.
Finally, all output drivers are converted to runtime PM, which greatly
simplifies the handling of clocks and resets.
* tag 'drm/tegra/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux: (35 commits)
drm/tegra: sor: Reject HDMI 2.0 modes
drm/tegra: sor: Prepare for generic PM domain support
drm/tegra: dsi: Prepare for generic PM domain support
drm/tegra: sor: Make XBAR configurable per SoC
drm/tegra: sor: Use sor1_src clock to set parent for HDMI
dt-bindings: display: tegra: Add source clock for SOR
drm/tegra: sor: Implement sor1_brick clock
drm/tegra: sor: Implement runtime PM
drm/tegra: hdmi: Implement runtime PM
drm/tegra: dsi: Implement runtime PM
drm/tegra: dc: Implement runtime PM
drm/tegra: hdmi: Enable audio over HDMI
drm/tegra: sor: Do not support deep color modes
drm/tegra: sor: Extract tegra_sor_mode_set()
drm/tegra: sor: Split out tegra_sor_apply_config()
drm/tegra: sor: Rename tegra_sor_calc_config()
drm/tegra: sor: Factor out tegra_sor_set_parent_clock()
drm/tegra: dpaux: Add pinctrl support
dt-bindings: Add bindings for Tegra DPAUX pinctrl driver
drm/tegra: Prepare DPAUX for supporting generic PM domains
...
|
