| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405154449.23038-5-daniel.vetter@ffwll.ch
|
|
tinydrm enable hook wants to play around with the new fb in
.atomic_enable(), thus we'll need access to the plane state.
Performed with coccinelle:
@r1@
identifier F =~ ".*enable$";
identifier P, CS;
@@
F(
struct drm_simple_display_pipe *P
,struct drm_crtc_state *CS
+ ,struct drm_plane_state *plane_state
)
{
...
}
@@
struct drm_simple_display_pipe *P;
expression E;
@@
{
+ struct drm_plane *plane;
...
+ plane = &P->plane;
P->funcs->enable(P
,E
+ ,plane->state
);
...
}
@@
identifier P, CS;
@@
struct drm_simple_display_pipe_funcs {
...
void (*enable)(struct drm_simple_display_pipe *P
,struct drm_crtc_state *CS
+ ,struct drm_plane_state *plane_state
);
...
};
v2: Pimp the commit message (David)
Cc: Marek Vasut <marex@denx.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: David Lechner <david@lechnology.com>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322202738.25817-1-ville.syrjala@linux.intel.com
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
|
|
We were previously selecting 1024x768 and 32BPP as the default
set-up for the PL111 consumers.
This does not work on elder systems: the device tree bindings
support a property "max-memory-bandwidth" in bytes/second that
states that if you exceed this the memory bus will saturate.
The result is flickering and unstable images.
Parse the "max-memory-bandwidth" and respect it when
intializing the driver. On the RealView PB11MP, Versatile and
Integrator/CP we get a nice console as default with this code.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307215819.15814-1-linus.walleij@linaro.org
|
|
Do not use deprecated drm_driver.{enable|disable)_vblank callbacks,
but use drm_simple_kms_helpe's pipe callbacks instead.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1518425574-32671-5-git-send-email-andr2000@gmail.com
|
|
The early Integrator CLCD synthesized in the Integrator CP and
IM-PD1 FPGAs are broken: their vertical and next base interrupts
are not functional. Support these variants by simply disabling
the use of the vblank interrupt on these variants.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-4-linus.walleij@linaro.org
|
|
The early Integrator CLCD synthesized in the Integrator CP and
IM-PD1 FPGAs are broken: their clock dividers do not work
properly. Support disabling the clock divider and drive the
clock directly from the parent under these circumstances.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-3-linus.walleij@linaro.org
|
|
The ARM Versatile series can do RGB/BGR565 with an external
"PLD" (Programmable Logical Device). However the CLCD does not
have control bits for this, so it needs to be set into the
ordinary 16BPP mode, then the RGB/BGR565 handling of the pixel
data is handled by configuring the PLD through the external
register.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-2-linus.walleij@linaro.org
|
|
If the bridge has a too strict setup time for the incoming
signals, we may not be fast enough and then we need to
compensate by outputting the signal on the inverse clock
edge so it is for sure stable when the bridge samples it.
Since bridges in difference to panels does not expose their
connectors, make the connector optional in the display
setup code.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112074854.9560-4-linus.walleij@linaro.org
|
|
The ARM reference designs in the Versatile family: Integrator,
Versatile and RealView can make use of the new DRM driver as well.
We just need to create a bit of platform-specific code for them
that we isolate to its own file.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-7-linus.walleij@linaro.org
|
|
The silcon and components around the PL111 may require some
variants to perform special set-up of the display. Add two
callbacks to manage this.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-6-linus.walleij@linaro.org
|
|
The old codebase has a delay between enabling and powering up the
PL11x.
According to the manual for PL110, ARM DDI 0161E page 1-5 and
the PL111 manual ARM DDI 0293C page 1-6, the power sequence should
be such that once Vdd is stable (which we assume it is at boot)
LCDEN is enabled first and then CLPOWER should be enabled
"after the signals have stabilized" and this is said to
be display-dependent. The old codebase uses 20ms.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-5-linus.walleij@linaro.org
|
|
We detect and enable the use of the PL110 variant, an earlier
incarnation of PL111. The only real difference is that the
control and interrupt enable registers have swapped place.
The Versatile AB and Versatile PB have a variant inbetween
PL110 and PL111, it is PL110 but they have already swapped the
two registers so those two need a bit of special handling.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-4-linus.walleij@linaro.org
|
|
This replaces the custom connector in the PL111 with the
panel bridge helper.
This works nicely for all standard panels, but since there
are several PL11x-based systems that will need to use the dumb
VGA connector bridge we use drm_of_find_panel_or_bridge()
and make some headroom for dealing with bridges that are
not panels as well, and drop a TODO in the code.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-3-linus.walleij@linaro.org
|
|
drm_fb_cma_create() and drm_fb_cma_prepare_fb() are just wrappers now,
use drm_gem_fb_create() and drm_gem_fb_prepare_fb() directly.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1502631125-13557-14-git-send-email-noralf@tronnes.org
|
|
This is the plumbing for supporting fb modifiers on planes. Modifiers
have already been introduced to some extent, but this series will extend
this to allow querying modifiers per plane. Based on this, the client to
enable optimal modifications for framebuffers.
This patch simply allows the DRM drivers to initialize their list of
supported modifiers upon initializing the plane.
v2: A minor addition from Daniel
v3:
* Updated commit message
* s/INVALID/DRM_FORMAT_MOD_INVALID (Liviu)
* Remove some excess newlines (Liviu)
* Update comment for > 64 modifiers (Liviu)
v4: Minor comment adjustments (Liviu)
v5: Some new platforms added due to rebase
v6: Add some missed plane inits (or maybe they're new - who knows at
this point) (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
|
|
If src_x/y were nonzero, we failed to shift them down by 16 to get the
pixel offset. The recent CMA helper function gets it right.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: bed41005e617 ("drm/pl111: Initial drm/kms driver for pl111")
Reported-by: Mircea Carausu <mircea.carausu@broadcom.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170603015733.13266-1-eric@anholt.net
Reviewed-by: Sean Paul <seanpaul@chromium.org>
|
|
structure pl111_display_funcs can be made static as it does not need to be
in global scope. Fixes sparse warning:
"warning: symbol 'pl111_display_funcs' was not declared. Should it
be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519110203.19417-1-colin.king@canonical.com
|
|
This is required for the panel to work on bcm911360, where CLCDCLK is
the fixed 200Mhz AXI41 clock. The rate set is still passed up to the
CLCDCLK, for platforms that have a settable rate on that one.
v2: Set SET_RATE_PARENT (caught by Linus Walleij), depend on
COMMON_CLK.
v3: Mark the clk_ops static (caught by Stephen).
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508193348.30236-1-eric@anholt.net
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This is a modesetting driver for the pl111 CLCD display controller
found on various ARM platforms such as the Versatile Express. The
driver has only been tested on the bcm911360_entphn platform so far,
with PRIME-based buffer sharing between vc4 and clcd.
It reuses the existing devicetree binding, while not using quite as
many of its properties as the fbdev driver does (those are left for
future work).
v2: Nearly complete rewrite by anholt, cutting 2/3 of the code thanks
to DRM core's excellent new helpers.
v3: Don't match pl110 any more, don't attach if we don't have a DRM
panel, use DRM_GEM_CMA_FOPS, update MAINTAINERS, use the simple
display helper, use drm_gem_cma_dumb_create (same as our wrapper).
v4: Change the driver's .name to not clash with fbdev in sysfs, drop
platform alias, drop redundant "drm" in DRM driver name, hook up
.prepare_fb to the CMA helper so that DMA fences should work.
v5: Move register definitions inside the driver directory, fix build
in COMPILE_TEST and !AMBA mode.
v6: Drop TIM2_CLKSEL for now to be consistent with existing DT
bindings, switch back to external register definitions.
Signed-off-by: Tom Cooksey <tom.cooksey@arm.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> (v5)
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170413031746.12921-2-eric@anholt.net
|
