| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support to generic audio codec via
ASoC hdmi-codec infrastucture which is merged recently.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[rebased on efc9194]
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
It is already optional at runtime. But this at least simplifies
backports to kernels without QCOM_SCM.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Global symbols in the kernel should be prefixed by the name
of the subsystem and/or driver to avoid conflicts when all
code is built-in.
In this case, function names like 'hdmi_register' or 'hdmi_set_mode'
are way too generic for an MSM specific DRM driver, so I'm renaming
them all to msm_hdmi_* here.
I also rename a lot of the 'static' symbols along with the global
names for consistency, even though those are relatively harmless;
they might only be slightly confusing when they show up in
backtraces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Add support for the HDMI PHY/PLL found in MSM8996/APQ8096.
Unlike the previous PHYs supported in the driver, this doesn't need
the powerup/powerdown ops. The PLL prepare/unprepare clock ops
enable/disable the phy itself.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Remove the old PHY ops managed by hdmi_platform_config and use them as ops
provided by the HDMI PHY driver.
Remove the old HDMI 8960 PLL code that used the top level HDMI TX mmio
base.
NOTE: With this commit, HDMI functionality will break until the HDMI
PHY/PLL register offsets in hdmi.xml.h aren't updated to be used as
separate domains.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Make HDMI core get its PHY by parsing the "phys" phandle. The core will use
this PHY reference to enable/disable PHY. The driver defers probe until PHY
isn't available.
The DT bindings used here is the same as the one used for PHYs using the
common PHY framework bindings.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Add a helper to initialize PLL in the PHY driver. HDMI PLLs are going to
have their own mmio base different from that of PHY.
For the clock code in hdmi_phy_8960.c, some changes were needed for it to
work with the updated register offsets. Create a copy of the updated clock
code in hdmi_pll_8960.c, instead of rewriting it in hdmi_phy_8960.c
itself. This removes the need to place CONFIG_COMMON_CLOCK checks all
around, makes the code more legible, and also removes some old checkpatch
warnings with the original code.
The older hdmi pll clock ops in hdmi_phy_8960.c will be removed later. The
driver will use these until the HDMI PHY/PLL register offsets aren't
considered as separate domains (i.e. their offsets start from 0).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Create a PHY device that represents the TX PHY and PLL parts of the HDMI
block.
This makes management of PHY specific resources (regulators and clocks)
much easier, and makes the PHY and PLL usable independently. It also
simplifies the core HDMI driver, which currently assigns phy ops among
many other things.
The PHY driver implementation done here is very similar to the PHY driver
we already have for DSI.
Keep the old hdmi_phy_funcs ops for now. The driver will use these until
the HDMI PHY/PLL register offsets aren't considered as separate
domains (i.e. their offsets start from 0).
The driver doesn't use the common PHY framework for now. This is because
it's hard to map our ops with the ops provided by the framework. The
bindings used for this is the generic phy bindings. So, this can be
adapted to the PHY framework in the future, if possible.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Make gpio allocation and usage iterative by parsing the gpios on a given
platform from a list. This gives us flexibility over what all gpios exist
for a platform, whether they are input or output, and what value they
should be set to.
In particular, this will make HDMI on 8x96 platforms easier to integrate
with the driver, as it doesn't have a HPD gpio input to them. Also, it
cleans things up a bit.
We still use the legacy gpio api here, as we might need to backport this
driver to downstream kernels.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
->reset() currently only accesses HDMI core registers, and yet it
is located in hdmi_phy*. Since no PHY registers are being
accessed during ->reset(), it would be better to bring that
function in hdmi core module where HDMI core registers are
usually being accessed.
This will also help for msm8x94 for which no PHY registers
accesses are done (->phy_init == NULL) but the HDMI PHY reset
from HDMI core still needs to be done.
Note:
SW_RESET_PLL bit is not written in hdmi_phy_8x60_reset(); this
write should not affect anything if the corresponding field is
not writable.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[fixed warning about unused 'phy' in hpd_enable() while merging]
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Add HDMI HDCP support including HDCP PartI/II/III authentication.
V1: Initial Change
V2: Address Bjorn&Rob's comments
Refactor the authentication process to use single work instead
of multiple work for different authentication stages.
V3: Update to align with qcom SCM api.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Instead of reporting BUG_ON when resources arrays are not
dimensioned correctly, this patch does a dynamic allocation of
these arrays. This is needed for the following patches that add a
regulator for a new target.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Currently, third party bridge drivers(ptn3460) are dependent
on the corresponding encoder driver init, since bridge driver
needs a drm_device pointer to finish drm initializations.
The encoder driver passes the drm_device pointer to the
bridge driver. Because of this dependency, third party drivers
like ptn3460 doesn't adhere to the driver model.
In this patch, we reframe the bridge registration framework
so that bridge initialization is split into 2 steps, and
bridge registration happens independent of drm flow:
--Step 1: gather all the bridge settings independent of drm and
add the bridge onto a global list of bridges.
--Step 2: when the encoder driver is probed, call drm_bridge_attach
for the corresponding bridge so that the bridge receives
drm_device pointer and continues with connector and other
drm initializations.
The old set of bridge helpers are removed, and a set of new helpers
are added to accomplish the 2 step initialization.
The bridge devices register themselves onto global list of bridges
when they get probed by calling "drm_bridge_add".
The parent encoder driver waits till the bridge is available
in the lookup table(by calling "of_drm_find_bridge") and then
continues with its initialization.
The encoder driver should also call "drm_bridge_attach" to pass
on the drm_device to the bridge object.
drm_bridge_attach inturn calls "bridge->funcs->attach" so that
bridge can continue with drm related initializations.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
A left-over from prior to component framework. The original intent was
to deal with hdmi getting unloaded before the master component, but that
isn't really going to work anyways. These days with the component
framework taking care to unload the master component first, we don't
have to worry about this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
For mdp5, the irqs of hdmi/eDP/dsi0/dsi1 blocks get routed through the
mdp block. In order to decouple hdmi/eDP/etc, register an irq domain
in mdp5. When hdmi/dsi/etc are used with mdp4, they can directly setup
their irqs in their DT nodes as normal. When used with mdp5, instead
set the mdp device as the interrupt-parent, as in:
mdp: qcom,mdss_mdp@fd900000 {
compatible = "qcom,mdss_mdp";
interrupt-controller;
#interrupt-cells = <1>;
...
};
hdmi: qcom,hdmi_tx@fd922100 {
compatible = "qcom,hdmi-tx-8074";
interrupt-parent = <&mdp>;
interrupts = <8 0>; /* MDP5_HW_INTR_STATUS.INTR_HDMI */
...
};
There is a slight awkwardness, in that we cannot disable child irqs
at the mdp level, they can only be cleared in the child block. So
you must not use threaded irq handlers in the child. I'm not sure
if there is a better way to deal with that.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
lpm-mux is programmed to enable HDMI connector
on the docking station for S805 chipset based
devices.
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The clock driver usually complains when a clock is being prepared
before setting its rate. It is the case here for "core_clk" which
needs to be set at 19.2 MHz before we attempt a prepare_enable().
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The HDMI block is basically the same between older SoC's with mdp4
display controller, and newer ones with mdp5.
So mostly this consists of better abstracting out the different sets of
regulators, clks, etc. In particular, for regulators and clks we can
split it up by what is needed for hot plug detect to work, and what is
needed to light up the display.
Also, 8x74 has a new phy.. a very simple one, but split out into a
different mmio space. And with mdp5, the irq is shared with mdp, so we
don't directly register our own irq handler.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Drop the msm_connector base class, and special calls to base class
methods from the encoder, and use instead drm_bridge. This allows for a
cleaner division between the hdmi (and in future dsi) blocks, from the
mdp block.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The snapdragon chips have multiple different display controllers,
depending on which chip variant/version. (As far as I can tell, current
devices have either MDP3 or MDP4, and upcoming devices have MDSS.) And
then external to the display controller are HDMI, DSI, etc. blocks which
may be shared across devices which have different display controller
blocks.
To more easily add support for different display controller blocks, the
display controller specific bits are split out into a "kms" module,
which provides the kms plane/crtc/encoder objects.
The external HDMI, DSI, etc. blocks are part encoder, and part connector
currently. But I think I will pull in the drm_bridge patches from
chromeos tree, and split them into a bridge+connector, with the
registers that need to be set in modeset handled by the bridge. This
would remove the 'msm_connector' base class. But some things need to be
double checked to make sure I could get the correct ON/OFF sequencing..
This patch adds support for mdp4 crtc (including hw cursor), dtv encoder
(part of MDP4 block), and hdmi.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
