| Age | Commit message (Collapse) | Author |
|---|
|
Most places in the vblank code use min() to clamp scanline
counters below vtotal. But we missed one in the gen3/4
pixel counter based codepath.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230404175431.23064-3-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
|
|
In order to move VRR enable/disable to a place where it's also
applicable to fastsets we need to be prepared to configure
the pipe into non-VRR mode initially, and then later switch
to VRR mode. To that end allow the active timings to be configured
in non-VRR mode temporarily even when the crtc_state says we're
going to be using VRR.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320203352.19515-5-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
|
|
Pull the scanline_offset calculation into its own function. Might
have further use for this later with DSB scanline waits.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230310235828.17439-4-ville.syrjala@linux.intel.com
|
|
Move intel_crtc_update_active_timings() into intel_vblank.c
where it more properly belongs.
Also do the s/dev_priv/i915/ modernization rename while at it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230310235828.17439-3-ville.syrjala@linux.intel.com
|
|
Rename PIPECONF to TRANSCONF to make it clear what it actually
applies to.
While the usual convention is to pick the earliers name I think
in this case it's more clear to use the later name. Especially
as even the register offset is in the wrong range (0x70000 vs.
0x60000) and thus makes it look like this is per-pipe.
There is one place in gvt that's doing something with TRANSCONF
while iterating with for_each_pipe(). So that might not be doing
the right thing for TRANSCODER_EDP, dunno. Not knowing what it
does I left it as is to avoid breakage.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Add intel_de_read64_2x32() wrapper for the uncore version of the same,
and use it to read the high and low frame registers. Avoid duplicating
code for existing helpers.
The slight functional difference is checking that the entire high
register remains the same across two reads, instead of just the part
we're interested in. This should be of no consequence. (Unless those
bits function as a PRNG.)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/33853549adff82045b95af527e14cfdff5712470.1673873708.git.jani.nikula@intel.com
|
|
Use the intel_de_* functions for display registers.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ecfac5ebddcb46be1ddf2e34e52648fbf9fa4ca6.1673873708.git.jani.nikula@intel.com
|
|
Reduce clutter in intel_display.c by moving the scanline moving/stopped
wait functions to intel_vblank.[ch].
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3613b8c22e5022ebf61ab942e6bc81b717e8f520.1673873708.git.jani.nikula@intel.com
|
|
The vblank/scanline code is fairly isolated in i915_irq.c. Split it out
to new intel_vblank.[ch].
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3e3e9016f5135dccae5110c291ba048567622e7a.1673873708.git.jani.nikula@intel.com
|
