| Age | Commit message (Collapse) | Author |
|---|
|
When intel_dp_init_connector fails, some power wells used in dp aux
communication may not be completely disabled yet. This may result in a
null pointer dereference when icl_aux_pw_to_phy() is called from
icl_combo_phy_aux_power_well_disable() after the encoder and connector
are already freed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221222201804.1380963-1-maarten.lankhorst@linux.intel.com
|
|
Use the information stored in display info. Add intel_dp_has_hdmi_sink()
helper to access it.
v2: Rebased
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/748103fda572b3552e5bbdafb300d8508d4eeaf4.1685437500.git.jani.nikula@intel.com
|
|
Use the information stored in display info.
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/695bbe8b5ebee6e492f95a1c818da15691752dc8.1685437500.git.jani.nikula@intel.com
|
|
disconnects
If the output on a DP-alt link with its sink disconnected is kept
enabled for too long (about 20 sec), then some IOM/TCSS firmware timeout
will cause havoc on the PCI bus, at least for other GFX devices on it
which will stop powering up. Since user space is not guaranteed to do a
disabling modeset in time, switch such disconnected but active links to
TBT mode - which is without such shortcomings - with a 2 second delay.
If the above condition is detected already during the driver load/system
resume sanitization step disable the output instead, as at that point no
user space or kernel client depends on a consistent output state yet and
because subsequent atomic modeset on such connectors - without the
actual sink capabilities available - can fail.
An active/disconnected port as above will also block the HPD status of
other active/disconnected ports to get updated (stuck in the connected
state), until the former port is disabled, its PHY is disconnected and
a ~10 ms delay has elapsed. This means the link state for all TypeC
ports/CRTCs must be rechecked after a CRTC is disabled due to the above
reason. For this disconnect the PHY synchronously after the CRTC/port is
disabled and recheck all CRTCs for the above condition whenever such a
port is disabled.
To account for a race condition during driver loading where the sink is
disconnected after the above sanitization step and before the HPD
interrupts get enabled, do an explicit check/link reset if needed from
the encoder's late_register hook, which is called after the HPD
interrupts are enabled already.
v2:
- Handle an active/disconnected port blocking the HPD state update of
another active/disconnected port.
- Cancel the delayed work resetting the link also from the encoder
enable/suspend/shutdown hooks.
- Rebase on the earlier intel_modeset_lock_ctx_retry() addition,
fixing here the missed atomic state reset in case of a retry.
- Fix handling of an error return from intel_atomic_get_crtc_state().
- Recheck if the port needs to be reset after all the atomic state
is locked and async commits are waited on.
v3:
- Add intel_crtc_needs_link_reset(), instead of open-coding it,
keep intel_crtc_has_encoders(). (Ville)
- Fix state dumping and use a bitmask to track disabled CRTCs in
intel_sanitize_all_crtcs(). (Ville)
- Set internal in intel_atomic_state right after allocating it.
(Ville)
- Recheck all CRTCs (not yet force-disabled) after a CRTC is
force-disabled for any reason (not only due to a link state)
in intel_sanitize_all_crtcs().
- Reduce delay after CRTC disabling to 20ms, and use the simpler
msleep().
- Clarify code comment about HPD behaviour in
intel_sanitize_all_crtcs().
- Move all the TC link reset logic to intel_tc.c .
- Cancel the link reset work synchronously during system suspend,
driver unload and shutdown.
v4:
- Rebased on previous patch, which allows calling the TC port
suspend/cleanup handlers without modeset locks held; remove the
display driver suspended assert from the link reset work
accordingly.
v5: (Ville)
- Remove reset work canceling from intel_ddi_pre_pll_enable().
- Track a crtc vs. pipe mask in intel_sanitize_all_crtcs().
- Add reset_link_commit() to clarify the
intel_modeset_lock_ctx_retry loop.
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5860
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-2-imre.deak@intel.com
|
|
Factor out a helper used by a follow up patch to reset an active DP
link.
No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-12-imre.deak@intel.com
|
|
Split hotplug irq handling out of i915_irq.[ch] into
display/intel_hotplug_irq.[ch].
The line between the new intel_hotplug_irq.[ch] and the existing
intel_hotplug.[ch] needs further clarification, but the first step is to
move the stuff out of i915_irq.[ch].
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230515101738.2399816-2-jani.nikula@intel.com
|
|
Check for MODE_H_ILLEGAL before calculating max rates, lanes etc.
Move comments about compressed bpp U6.4 format closer to where it is used.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-7-ankit.k.nautiyal@intel.com
|
|
Common function to get the sink format for a given mode for DP.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-6-ankit.k.nautiyal@intel.com
|
|
Start passing the sink_format, to all functions that take a bool
ycbcr420_output as parameter. This will make the functions generic,
and will serve as a slight step towards 4:2:2 support later.
v2: Rebased.
v3: Correct the checks in places concerned with pipe output. (Ville)
Other minor styling and refactoring fixes, as suggested by Ville.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-5-ankit.k.nautiyal@intel.com
|
|
Handle the case with DP to HDMI PCON, where sink_format is set to YCbCr444.
In that case PCON is required to be configured to convert from given
output_format to YCbCR444.
v2: Drop drm_WARN for invalid case, let MISSING_CASE catch it. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-4-ankit.k.nautiyal@intel.com
|
|
The decision to use DFP output format conversion capabilities should be
during compute_config phase.
This patch uses the members of intel_dp->dfp to only store the
format conversion capabilities of the DP device and uses the crtc_state
sink_format member, to program the protocol-converter for
colorspace/format conversion.
v2: Use sink_format to determine the color conversion config for the
pcon (Ville).
v3: Fix typo: missing 'break' in switch case (lkp kernel test robot).
v4: Add helper to check if DP supports YCBCR420.
v5: Simplify logic for computing output_format, based on the given
sink_format. (Ville).
Added scaler constraint for YCbCr420 output.
v6: Split the patch for Scaler constraint for Ycbcr420.
v7: Simplify the policy for selecting output_format:
Always try for RGB first, followed by YCBCR444, and finally by YCBCR420.
v8: Removed redundant comments, minor refactoring. (Ville)
v9: Added member for ycbcr420 passthrough cap, fixed minor issues. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-3-ankit.k.nautiyal@intel.com
|
|
The decision to use DFP output format conversion capabilities should be
during compute_config phase.
This patch adds new member to crtc_state to represent the final
output_format to the sink. In case of a DFP this can be different than
the output_format, as per the format conversion done via the PCON.
This will help to store only the format conversion capabilities of the
DP device in intel_dp->dfp, and use crtc_state to compute and store the
configuration for color/format conversion for a given mode.
v2: modified the new member to crtc_state to represent the final
output_format that eaches the sink, after possible conversion by
PCON kind of devices. (Ville)
v3: Addressed comments from Ville:
-Added comments to clarify difference between sink_format and
output_format.
-Corrected the order of setting sink_format and output_format.
-Added readout for sink_format in get_pipe_config hooks.
v4: Set sink_format for intel_sdvo too. (Ville)
v5: Rebased.
v6: Fixed condition to go for YCbCr420 format for dp and hdmi. (Ville)
v7: Fix the condition to set sink_format for HDMI.
Set hdmi output_format simply as sink_format. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-2-ankit.k.nautiyal@intel.com
|
|
drm_dp_dsc_sink_max_slice_count() may return 0 if something goes
wrong on the part of the DSC sink and its DPCD register. This null
value may be later used as a divisor in intel_dsc_compute_params(),
which will lead to an error.
In the unlikely event that this issue occurs, fix it by testing the
return value of drm_dp_dsc_sink_max_slice_count() against zero.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: a4a157777c80 ("drm/i915/dp: Compute DSC pipe config in atomic check")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230418140430.69902-1-n.zhandarovich@fintech.ru
|
|
C20 phy PLL programming sequence for DP, DP2.0, HDMI2.x non-FRL and
HDMI2.x FRL. This enables C20 MPLLA and MPLLB programming sequence. add
4 lane support for c20.
v2: Add 6.48Gbps and 6.75Gbps modes for eDP (RK)
Fix lane check (RK)
Fix multiline commenting (Arun)
use usleep_range() instead of msleep() (Andi)
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-2-mika.kahola@intel.com
|
|
We need to untangle the mess where some SKL machines (at least)
declare both DDI A and DDI E to be present in their VBT, and
both using AUX A. DDI A is a ghost eDP, wheres DDI E may be a
real DP->VGA converter.
Currently that is handled by checking the VBT child devices
for conflicts before output probing. But that kind of solution
will not work for the ADL phantom dual eDP VBTs. I think on
those we just have to probe the eDP first. And would be nice
to use the same probe scheme for everything.
On these SKL systems if we probe DDI A first (which is only
natural given it's declared by VBT first) we will get an answer
via AUX, but it came from the DP->VGA converter hooked to the
DDI E, not DDI A. Thus we mistakenly register eDP on DDI A
and screw up the real DP device in DDI E.
To fix this let's check the HPD live state during the eDP probe.
If we got an answer via DPCD but HPD is still down let's assume
we got the answer from someone else.
Smoke tested on all my eDP machines (ilk,hsw-ult,tgl,adl) and
I also tested turning off all HPD hardware prior to loading
i915 to make sure it all comes up properly. And I simulated
the failure path too by not turning on HPD sense and that
correctly gave up on eDP.
I *think* Windows might just fully depend on HPD here. I
couldn't really find any other way they probe displays. And
I did find code where they also check the live state prior
to AUX transfers (something Imre and I have also talked
about perhaps doing). That would also solve this as we'd
not succeed in the eDP probe DPCD reads.
Other solutions I've considered:
- Reintrduce DDI strap checks on SKL. Unfortunately we just
don't have any idea how reliable they are on real production
hardware, and commit 5a2376d1360b ("drm/i915/skl: WaIgnoreDDIAStrap
is forever, always init DDI A") does suggest that not very.
Sadly that commit is very poor in details :/
Also the systems (Asrock B250M-HDV at least) fixed by commit
41e35ffb380b ("drm/i915: Favor last VBT child device with
conflicting AUX ch/DDC pin") might still not work since we
don't know what their straps indicate. Stupid me for not
asking the reporter to check those at the time :(
We have currently two CI machines (fi-cfl-guc,fi-cfl-8700k
both MS-7B54/Z370M) that also declare both DDI A and DDI E
in VBT to use AUX A, and on these the DDI A strap is also
set. There doesn't seem to be anything hooked up to either
DDI however. But given the DDI A strap is wrong on these it
might well be wrong on the Asrock too.
Most other CI machines seem to have straps that generally
match the VBT. fi-kbl-soraka is an exception though as DDI D
strap is not set, but it is declared in VBT as a DP++ port.
No idea if there's a real physical port to go with it or not.
- Some kind of quirk just for the cases where both DDI A and DDI E
are present in VBT. Might be feasible given we've ignored
DDI A in these cases up to now successfully. But feels rather
unsatisfactory, and not very future proof against funny VBTs.
References: https://bugs.freedesktop.org/show_bug.cgi?id=111966
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230417131728.7705-4-ville.syrjala@linux.intel.com
|
|
Add DP rates for Meteorlake.
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-2-radhakrishna.sripada@intel.com
|
|
Leftovers from before display debugfs was separated to its own file.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230411131922.401602-1-jani.nikula@intel.com
|
|
DSC_Output_Format_Sink_Support entry is added to i915_dsc_fec_support_show
to depict if sink supports DSC output formats (RGB/YCbCr420/YCbCr444).
Also, new debugfs entry is created to enforce output format. This is
required because of our driver policy. For ex. if a mode is supported
in both RGB and YCbCr420 output formats by the sink, our policy is to
try RGB first and fall back to YCbCr420, if mode cannot be shown
using RGB. So, to test other output formats like YCbCr420 or YCbCr444,
we need a debugfs entry (force_dsc_output_format) to force this
output format.
v2: -Func name changed to intel_output_format_name() (Jani N)
-Return forced o/p format from intel_dp_output_format() (Jani N)
v3: -output_format_str[] to remain static (Jani N)
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230309062855.393087-8-suraj.kandpal@intel.com
|
|
Now that we have laid the groundwork for YUV420 Enablement
we fill up native_420 field in vdsc_cfg and add appropriate
checks wherever required.
---v2
-adding native_422 field as 0 [Vandita]
-filling in second_line_bpg_offset, second_line_offset_adj
and nsl_bpg_offset in vds_cfg when native_420 is true
---v3
-adding display version check to solve igt issue
--v7
-remove is_pipe_dsc check as its always true for D14 [Jani]
--v10
-keep sink capability check [Jani]
-move from !(x == y || w == z) to x !=y && w != z [Jani]
--v11
-avoid native_420 computation if not gen14 [Uma]
--v12
-fix state mismatch issue of compressed_bpp
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230309062855.393087-6-suraj.kandpal@intel.com
|
|
Go with DSC only if the given output_format is supported.
v2: Use drm helper to get DSC format support for sink.
v3: remove drm_dp_dsc_compute_bpp.
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230309062855.393087-3-suraj.kandpal@intel.com
|
|
While computing compressed bpp, maximum value of bits_per_pixel is
calculated that can be supported with the given link configuration
for a given mode. Avoid rounding up of this max bits_per_pixel.
Also improve documentation for computing max bits_per_pixel.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230223115509.3980226-1-ankit.k.nautiyal@intel.com
|
|
We currently have an issue with some BPPs when using DSC.
According to the HW team, the reason is that a single VDSC engine
instance has some BW limitations that must be accounted for.
So, whenever we approach around 90% of the CDCLK, a second VDSC engine
has to be used.
This always means using two slices. However, in our current code,
the amount of slices is calculated independently of whether
we need to enable the second VDSC engine or not.
This leads to some logical issues when, according to the pixel clock needs,
we need to enable the second VDSC engine.
But as we calculated previously that we can only use a single slice,
we can't do that and fail.
So, we need to fix that so that the number of VDSC engines enabled
should depend on the number of slices, and the number of slices
should also depend on BW requirements.
Lastly, we didn't have BPP limitation for ADLP/MTL/DG2 implemented,
which says that DSC output BPPs can only be chosen within the range of 8 to 27
(BSpec 49259).
All of this applied together allows us to fix existing FIFO underruns,
which we have in many DSC tests.
v2: - Replace min with clamp_t(Jani Nikula)
- Fix commit message(Swati Sharma)
- Added "Closes"(Swati Sharma)
BSpec: 49259
HSDES: 18027167222
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8231
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230306080401.22552-1-stanislav.lisovskiy@intel.com
|
|
Grab the HDR DPCD refresh timeout (time we need to wait after
writing the sourc OUI before the HDR DPCD registers are ready)
from the VBT.
Windows doesn't even seem to have any default value for this,
which is perhaps a bit weird since the VBT value is documented
as TGL+ and I thought the HDR backlight stuff might already be
used on earlier platforms. To play it safe I left the old
hardcoded 30ms default in place. Digging through some internal
stuff that seems to have been a number given by the vendor for
one particularly slow TCON. Although I did see 50ms mentioned
somewhere as well.
Let's also include the value in the debug print to ease
debugging, and toss in the customary connector id+name as well.
The TGL Thinkpad T14 I have sets this to 0 btw. So the delay
is now gone on this machine:
[CONNECTOR:308:eDP-1] Detected Intel HDR backlight interface version 1
[CONNECTOR:308:eDP-1] Using Intel proprietary eDP backlight controls
[CONNECTOR:308:eDP-1] SDR backlight is controlled through PWM
[CONNECTOR:308:eDP-1] Using native PCH PWM for backlight control (controller=0)
[CONNECTOR:308:eDP-1] Using AUX HDR interface for backlight control (range 0..496)
[CONNECTOR:308:eDP-1] Performing OUI wait (0 ms)
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230220164718.23117-1-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
|
|
intel_dp_has_audio() has no need for the crtc_state, so don't
pass it in.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230220151731.6852-2-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Rename PIPECONF to TRANSCONF to make it clear what it actually
applies to.
While the usual convention is to pick the earliers name I think
in this case it's more clear to use the later name. Especially
as even the register offset is in the wrong range (0x70000 vs.
0x60000) and thus makes it look like this is per-pipe.
There is one place in gvt that's doing something with TRANSCONF
while iterating with for_each_pipe(). So that might not be doing
the right thing for TRANSCODER_EDP, dunno. Not knowing what it
does I left it as is to avoid breakage.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Switch a lot of the intel_bios_foo() stuff to just accept the
devdata (VBT child device info) directly, instead of taking
detours via vbt.ports[].
Also unify the function naming scheme.
v2: Drop the redundant "encoder" from the dp/hdmi specific functions
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216000425.32216-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
It's confusing to debug backlight issues when one can't
easily even tell what kind of backlight control was
selected. Sprinkle uniform debug messages to all the
backlight setup functions.
Also the one that was already there (ext_pwm) was
using drm_info() for some reason. I don't think that's
warranted so switch it to drm_dbg_kms() as well.
v2: Deal with AUX backlights too (Jani)
Move the VLV/CHV initial pipe debug there too (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215135616.30411-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Since we now populate encoder->devdata for all DP capable
platforms we can consult it directly during the eDP
connector init instead of taking a detour via some global
list/array.
Unfortunately we can't quite get rid of
intel_dp_is_port_edp() since it's still used by the higher
level ilk/vlv/chv output setup code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
intel_bios_encoder_is_lspcon()
We always have encoder->devdata available on the platforms
that can have LSPCON. So let's start looking there instead
of digging it out from vbt.ports[].
And let's rename the function to fit the common pattern
for these things.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
According VDSC spec 1.2a Section 3.8 Options for Slice
implies that 108 lines is an optimal slice height, but any
size can be used as long as vertical active
integer multiple and maximum vertical slice count requirements are met.
Bspec: 49259
--v3
-remove previous fallback code and return slice_height as 2 [Jani]
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230214052017.3312044-1-suraj.kandpal@intel.com
|
|
It's a bit confusing to have two cached EDIDs in struct intel_connector
with slightly different purposes. Make the distinction a bit clearer by
moving the EDID cached for eDP and LVDS panels at connector init time to
struct intel_panel, and name it fixed_edid. That's what it is, a fixed
EDID for the panels.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/328350ef918638928a8286cdbab3107c8258332d.1674643465.git.jani.nikula@intel.com
|
|
Simplify validation and use by converting to drm_edid.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6abb01f1e97d54a3c11bec24377f035df412b492.1674643465.git.jani.nikula@intel.com
|
|
Try to use struct drm_edid where possible, even if having to fall back
to looking into struct edid down low via drm_edid_raw().
v2: Rebase
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/897807d62f74f690a173ecd405e25c6ccdd63b98.1674643465.git.jani.nikula@intel.com
|
|
Convert all the connectors that use cached connector edid and
detect_edid to drm_edid.
Since drm_get_edid() calls drm_connector_update_edid_property() while
drm_edid_read*() do not, we need to call drm_edid_connector_update()
separately, in part due to the EDID caching behaviour in HDMI and
DP. Especially DP depends on the details parsed from EDID. (The big
behavioural change conflating EDID reading with parsing and property
update was done in commit 5186421cbfe2 ("drm: Introduce epoch counter to
drm_connector"))
v6: Rebase on drm_edid_connector_add_modes()
v5: Fix potential uninitialized var use (kernel test robot <lkp@intel.com>)
v4: Call drm_edid_connector_update() after reading HDMI/DP EDID
v3: Don't leak vga switcheroo EDID in LVDS init (Ville)
v2: Don't leak opregion fallback EDID (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/eabb4de932841b38b34cc2818ea9fbf7c10224fd.1674643465.git.jani.nikula@intel.com
|
|
Stash the ELD into the crtc_state and precompute it. This gets
rid of the ugly ELD mutation during intel_audio_codec_enable(),
and opens the door for the state checker.
v2: Make another copy for the acomp hooks (Chaitanya)
Split out the bogus ELD handling change (Jani)
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-5-ville.syrjala@linux.intel.com
|
|
Defeature Display Interlace support.
Support for interlace modes is removed from Gen 12 onwards.
Pruning the interlace modes for HDMI for Display >=12.
Bspec: 50490
v2: Add check for both DP and HDMI. (Ville)
Get rid of redundant check for interlace mode in modevalid. (Ville)
v3: Simplify the condition to avoid interlace modes. (Jani)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105124125.1129653-1-ankit.k.nautiyal@intel.com
|
|
Since the DP/HDMI connector do not set connector->doublescan_allowed,
the doublescan modes will get automatically filtered during
drm_helper_probe_single_connector_modes().
Therefore check for double scan modes is not required and is dropped
from modevalid functions for both DP and HDMI.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221017143038.1748319-2-ankit.k.nautiyal@intel.com
|
|
We now accept timeslots param exactly how the variable
sounds: amount of timeslots, but not ratio timeslots/64.
So for SST case(when we have all timeslots for use), it
should be 64, but not 1.
This caused some issues in the tests.
v2: Fixed comments
References: https://gitlab.freedesktop.org/drm/intel/-/issues/6860
Fixes: 52f14682ac4d ("drm/i915: Bpp/timeslot calculation fixes for DP MST DSC")
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230109140210.25822-1-stanislav.lisovskiy@intel.com
|
|
Fix intel_dp_dsc_compute_config, previously timeslots parameter
was used in fact not as a timeslots, but more like a ratio
timeslots/64, which of course didn't have any effect for SST DSC,
but causes now issues for MST DSC.
Secondly we need to calculate pipe_bpp using intel_dp_dsc_compute_bpp
only for SST DSC case, while for MST case it has been calculated
earlier already with intel_dp_dsc_mst_compute_link_config.
Third we also were wrongly determining sink min bpp/max bpp, those
limites should be intersected with our limits to find common
acceptable bpp's, plus on top of that we should align those with
VESA bpps and only then calculate required timeslots amount.
Some MST hubs started to work only after third change was made.
v2: Make kernel test robot happy(claimed there was unitialzed use,
while there is none)
v3: Rename intel_dp_dsc_nearest_vesa_bpp to intel_dp_dsc_nearest_valid_bpp
(Manasi Navare)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221123100718.29130-1-stanislav.lisovskiy@intel.com
|
|
We might to use that function separately from intel_dp_dsc_compute_config
for DP DSC over MST case, because allocating bandwidth in that
case can be a bit more tricky. So in order to avoid code copy-pasta
lets extract this to separate function and reuse it for both SST
and MST cases.
v2: Removed multiple blank lines
v3: Rename intel_dp_dsc_nearest_vesa_bpp to intel_dp_dsc_nearest_valid_bpp
to reflect its meaning more properly.
(Manasi Navare)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221123100551.29080-1-stanislav.lisovskiy@intel.com
|
|
Whenever we are not able to get enough timeslots
for required PBN, let's try to allocate those
using DSC, just same way as we do for SST.
v2: Removed intel_dp_mst_dsc_compute_config and refactored
intel_dp_dsc_compute_config to support timeslots as a
parameter(Ville Syrjälä)
v3: - Rebased
- Added a debug to see that we at least try reserving
VCPI slots using DSC, because currently its not visible
from the logs, thus making debugging more tricky.
- Moved timeslots to numerator, where it should be.
v4: - Call drm_dp_mst_atomic_check already during link
config computation, because we need to know already
by this moment if uncompressed amount of VCPI slots
needed can fit, otherwise we need to use DSC.
(thanks to Vinod Govindapillai for pointing this out)
v5: - Put pipe_config->bigjoiner_pipes back to original
condition in intel_dp_dsc_compute_config
(don't remember when I lost it)
v6: - Removed unnecessary drm_dp_mst_atomic_check as it is
now always called in a newly introduced
intel_dp_mst_find_vcpi_slots_for_bpp function
(Vinod Govindapillai)
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221101094222.22091-5-stanislav.lisovskiy@intel.com
|
|
On ICP-ADP the pins used by the second PPS can be alternatively
muxed to some other function. In that case the second power
sequencer is unusable.
Unfortunately (on my ADL Thinkpad T14 gen3 at least) the
BIOS still likes to enable the VDD on the second PPS (due
to the VBT declaring the second bogus eDP panel) even when
not correctly muxed, so we need to deal with it somehow.
For now let's just initialize the PPS as normal, and then
use the normal eDP probe failure VDD off path to turn it off
(and release the wakeref the PPS init grabbed). The
alternative of just declaring that the platform has a single
PPS doesn't really work since it would cause the second eDP
probe to also try to use the first PPS and thus clobber the
state for the first (real) eDP panel.
Cc: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-7-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
|
|
Lots of ADL machines out there with bogus VBTs that declare
two eDP child devices. In order for those to work we need to
figure out which power sequencer to use before we try the EDID
read. So let's do the panel VBT init early if we can, falling
back to the post-EDID init otherwise.
The post-EDID init panel_type=0xff approach of assuming the
power sequencer should already be enabled doesn't really work
with multiple eDP panels, and currently we just end up using
the same power sequencer for both eDP ports, which at least
confuses the wakeref tracking, and potentially also causes us
to toggle the VDD for the panel when we should not.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-3-ville.syrjala@linux.intel.com
|
|
Bspecs has updated recently to remove the restriction to disable
DDI/Transcoder before setting PHY test pattern. This update is to
address PHY compliance test failures observed on a port with LTTPR.
The issue is that when Transc. is disabled, the main link signals fed
to LTTPR will be dropped invalidating link training, which will affect
the quality of the phy test pattern when the transcoder is enabled again.
v2: Update commit message (Clint)
v3: Add missing Signed-off in v2
v4: Update Bspec and commit message for pre-gen12 (Jani)
Bspec: 50482, 7555
Fixes: 8cdf72711928 ("drm/i915/dp: Program vswing, pre-emphasis, test-pattern")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221123220926.170034-1-khaled.almahallawy@intel.com
|
|
Use HAS_DSC(__i915) wrapper containing runtime info of has_dsc
member. Platforms supporting dsc has this flag enabled; no need of
DISPLAY_VER() check.
Also, simplified intel_dsc_source_support() based on above changes.
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221110093312.13932-1-swati2.sharma@intel.com
|
|
Enable the SDP split configuration for DP2.0.
v2: Move the register handling out of compute config function (JaniN)
v3: Patch styling and register access based on platform support (JaniN)
v4: Rebased
v5: Use unconditional clear bit in intel_de_rmw (Jani Nikula)
Bspec: 67768
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221121150718.1117628-1-vinod.govindapillai@intel.com
|
|
Panel power off delay is the time the panel power needs to remain off
after being switched off, before it can be switched on again.
For the purpose of respecting panel power off delay at driver probe,
assuming the panel was last switched off at driver probe is overly
pessimistic. If the panel was never on, we'd end up waiting for no
reason.
We don't know what has happened before kernel boot, but we can make some
assumptions:
- The panel may have been switched off right before kernel boot by some
pre-os environment.
- After kernel boot, the panel may only be switched off by i915.
- At i915 driver probe, only a previously loaded and removed i915 may
have switched the panel power off.
With these assumptions, we can initialize the last power off time to
kernel boot time, if we also ensure i915 driver remove waits for the
panel power off delay after switching panel power off.
This shaves off the time it takes from kernel boot to i915 probe from
the first panel enable, if (and only if) the panel was not already
enabled at boot.
The encoder destroy hook is pretty much the last place where we can
wait, right after we've ensured the panel power has been switched off,
and before the whole encoder is destroyed.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7417
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Lee Shawn C <shawn.c.lee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221116150657.1347504-1-jani.nikula@intel.com
|
|
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
|
|
Remove extraline left after intel_dp_configure_protocol_converter.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221011063447.904649-3-ankit.k.nautiyal@intel.com
|
|
For cases where DP has HDMI2.1 sink and FRL Link issues are detected,
reset the flag to state FRL trained status before restarting FRL
training.
Fixes: 9488a030ac91 ("drm/i915: Add support for enabling link status and recovery")
Cc: Swati Sharma <swati2.sharma@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com> (v2)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221011063447.904649-2-ankit.k.nautiyal@intel.com
|
