summaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/bridge
AgeCommit message (Collapse)Author
2020-02-13drm/bridge: ti-sn65dsi86: Train at faster rates if slower ones failDouglas Anderson
If we fail training at a lower DP link rate let's now keep trying until we run out of rates to try. Basically the algorithm here is to start at the link rate that is the theoretical minimum and then slowly bump up until we run out of rates or hit the max rate of the sink. We query the sink using a DPCD read. This is, in fact, important in practice. Specifically at least one panel hooked up to the bridge (AUO B116XAK01) had a theoretical min rate more than 1.62 GHz (if run at 24 bpp) and fails to train at the next rate (2.16 GHz). It would train at 2.7 GHz, though. Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.8.I251add713bc5c97225200894ab110ea9183434fd@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Group DP link training bits in a functionDouglas Anderson
We'll re-organize the ti_sn_bridge_enable() function a bit to group together all the parts relating to link training and split them into a sub-function. This is not intended to have any functional change and is in preparation for trying link training several times at different rates. One small side effect here is that if link training fails we'll now leave the DP PLL disabled, but that seems like a sane thing to do. Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.7.I1fc75ad11db9048ef08cfe1ab7322753d9a219c7@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Use 18-bit DP if we canDouglas Anderson
The current bridge driver always forced us to use 24 bits per pixel over the DP link. This is a waste if you are hooked up to a panel that only supports 6 bits per color or fewer, since in that case you can run at 18 bits per pixel and thus end up at a lower DP clock rate. Let's support this. While at it, let's clean up the math in the function to avoid rounding errors (and round in the correct direction when we have to round). Numbers are sufficiently small (because mode->clock is in kHz) that we don't need to worry about integer overflow. Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> [narmstrong: s/ran/can/] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.6.Iaf8d698f4e5253d658ae283d2fd07268076a7c27@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Read num lanes from the DP sinkDouglas Anderson
At least one panel hooked up to the bridge (AUO B116XAK01) only supports 1 lane of DP. Let's read this information and stop hardcoding 4 DP lanes. Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.5.Idbd0051d0de53f7e9d18a291ea33011c0854fcc6@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Config number of DP lanes Mo' BettaDouglas Anderson
The driver used to say that the value to program into bridge register 0x93 was dp_lanes - 1. Looking at the datasheet for the bridge, this is wrong. The data sheet says: * 1 = 1 lane * 2 = 2 lanes * 3 = 4 lanes A more proper way to express this encoding is min(dp_lanes, 3). At the moment this change has zero effect because we've hardcoded the number of DP lanes to 4. ...and (4 - 1) == min(4, 3). How fortunate! ...but soon we'll stop hardcoding the number of lanes. Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.4.If3e2d0493e7b6e8b510ea90d8724ff760379b3ba@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Don't use MIPI variables for DP linkDouglas Anderson
The ti-sn65dsi86 is a bridge from MIPI to DP and thus has two links: the MIPI link and the DP link. The two links do not need to have the same format or number of lanes. Stop using MIPI variables when talking about the DP link. This has zero functional change because: * currently we are hardcoding the MIPI link as unpacked RGB888 which requires 24 bits and currently we are not changing the DP link rate from the bridge's default of 8 bits per pixel. * currently we are hardcoding both the MIPI and DP as being 4 lanes. This is all in prep for fixing some of the above. Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.3.Ia6e05f4961adb0d4a0d32ba769dd7781ee8db431@changeid
2020-02-13drm/bridge: ti-sn65dsi86: zero is never greater than an unsigned intDouglas Anderson
When we iterate over ti_sn_bridge_dp_rate_lut, there's no reason to start at index 0 which always contains the value 0. 0 is not a valid link rate. This change should have no real effect but is a small cleanup. Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.2.Id445d0057bedcb0a190009e0706e9254c2fd48eb@changeid
2020-02-13drm/bridge: ti-sn65dsi86: Split the setting of the dp and dsi ratesDouglas Anderson
These two things were in one function. Split into two. This looks like it's duplicating some code, but don't worry. This is is just in preparation for future changes. This is intended to have zero functional change and will just make future patches easier to understand. Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.1.Icb765d5799e9651e5249c0c27627ba33a9e411cf@changeid
2020-02-12Merge v5.6-rc1 into drm-misc-fixesMaarten Lankhorst
We're based on v5.6, need v5.6-rc1 at least. :) Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
2020-02-11drm/bridge: tfp410: add pclk limitsTomi Valkeinen
Add pixel clock limits to the driver as per TFP410 datasheet: min 25MHz, max 165MHz. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200121094655.9092-1-tomi.valkeinen@ti.com
2020-02-10drm/bridge: panel: Fix typo in drm_panel_bridge_add docsEnric Balletbo i Serra
Fix the 'manged' typo with 'managed' in the drm_panel_bridge_add kernel-doc documentation. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218121223.30181-1-enric.balletbo@collabora.com
2020-02-10drm/bridge/synopsys: dsi: missing post disableYannick Fertré
Sometime the post_disable function is missing (not registered). Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/1579602296-7683-1-git-send-email-yannick.fertre@st.com
2020-02-10drm/bridge: sii902x: Select SND_SOC_HDMI_CODEC if SND_SOC is configuredJyri Sarha
To enable HDMI audio the SND_SOC_HDMI_CODEC needs to be configured. Enable HDMI audio by selecting SND_SOC_HDMI_CODEC if SND_SOC is configured. SND_SOC_HDMI_CODEC has no config menu entry and should be selected automatically by the drivers using it. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> [narmstrong: atomatically -> automatically] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191129152342.29145-1-jsarha@ti.com
2020-02-10drm/bridge: Add tc358768 driverPeter Ujfalusi
Add basic support for the Toshiba TC358768 RGB to DSI bridge. Not all the features of the TC358768 is implemented by the initial driver: MIPI_DSI_MODE_VIDEO and MIPI_DSI_FMT_RGB888 is only supported and tested. Only write is implemented for mipi_dsi_host_ops.transfer. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200131111553.472-3-peter.ujfalusi@ti.com
2020-02-10drm: bridge: adv7511: Add support for ADV7535Bogdan Togorean
ADV7535 is a DSI to HDMI bridge chip like ADV7533 but it allows 1080p@60Hz. v1p2 is fixed to 1.8V on ADV7535. Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200121082719.27972-3-bogdan.togorean@analog.com
2020-02-10drm: bridge: adv7511: Remove DRM_I2C_ADV7533 KconfigBogdan Togorean
This commit remove DRM_I2C_ADV7533 resulting a simpler driver and less choices in Kconfig. Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200121082719.27972-2-bogdan.togorean@analog.com
2020-02-10drm/bridge: ti-tfp410: Update drm_connector_init_with_ddc() error messageGeert Uytterhoeven
The code was changed to call drm_connector_init_with_ddc() instead of drm_connector_init(), but the corresponding error message was not updated. Fixes: cfb444552926989f ("drm/bridge: ti-tfp410: Provide ddc symlink in connector sysfs directory") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200115125653.5519-1-geert+renesas@glider.be
2020-02-10drm/bridge: tc358767: fix poll timeoutsTomi Valkeinen
Link training fails with: Link training timeout waiting for LT_LOOPDONE! main link enable error: -110 This is caused by too tight timeouts, which were changed recently in aa92213f388b ("drm/bridge: tc358767: Simplify polling in tc_link_training()"). With a quick glance, the commit does not change the timeouts. However, the method of delaying/sleeping is different, and as the timeout in the previous implementation was not explicit, the new version in practice has much tighter timeout. The same change was made to other parts in the driver, but the link training timeout is the only one I have seen causing issues. Nevertheless, 1 us sleep is not very sane, and the timeouts look pretty tight, so lets fix all the timeouts. One exception was the aux busy poll, where the poll sleep was much longer than necessary (or optimal). I measured the times on my setup, and now the sleep times are set to such values that they result in multiple loops, but not too many (say, 5-10 loops). The timeouts were all increased to 100ms, which should be more than enough for all of these, but in case of bad errors, shouldn't stop the driver as multi-second timeouts could do. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Fixes: aa92213f388b ("drm/bridge: tc358767: Simplify polling in tc_link_training()") Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191209082707.24531-1-tomi.valkeinen@ti.com
2020-01-31drm/bridge: Patch atomic hooks to take a drm_bridge_stateBoris Brezillon
This way the drm_bridge_funcs interface is consistent with the rest of the subsystem. The drivers implementing those hooks are patched too. v10: * Add changelog to the commit message v8 -> v9: * No changes v7: * Adjust things to the bridge_state changes v6: * Also fixed rcar-du/rcar_lvds.c same as analogix/analogix_dp_core.c v5: * No changes v4: * Rename func params into old_bridge_state * Add Laurent's Rb v3: * Old state clarification moved to a separate patch v2: * Pass the old bridge state Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> [narmstrong: renamed state as old_bridge_state in rcar_lvds_atomic_disable] Reviewed by: Jernej Skrabec <jernej.skrabec@siol.net> Tested-by: Jonas Karlman <jonas@kwiboo.se> Link: https://patchwork.freedesktop.org/patch/msgid/20200128135514.108171-5-boris.brezillon@collabora.com
2020-01-31drm/bridge: analogix: Plug atomic state hooks to the default implementationBoris Brezillon
This is needed to pass a bridge state to all atomic hooks, if we don't do that, the core can't duplicate/create bridge states. v10: * Add changelog to the commit message v9: * Add Neil's R-b * Move earlier in the series v8: * No changes v7: * New patch Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200128135514.108171-4-boris.brezillon@collabora.com
2020-01-22drm/bridge: Add I2C based driver for ps8640 bridgeJitao Shi
This patch adds drm_bridge driver for parade DSI to eDP bridge chip. Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org> [uli: followed API changes, removed FW update feature] Signed-off-by: Ulrich Hecht <uli@fpond.eu> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Tested-by: Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191230090419.137141-3-enric.balletbo@collabora.com
2020-01-08Revert "drm/bridge: Patch atomic hooks to take a drm_bridge_state"Boris Brezillon
This reverts commit f7619a58ef92 ("drm/bridge: Patch atomic hooks to take a drm_bridge_state"). Commit 6ed7e9625fa6 ("drm/bridge: Add a drm_bridge_state object") introduced a circular dependency between drm.ko and drm_kms_helper.ko which uncovered a misdesign in how the whole thing was implemented. Let's revert all patches depending on the bridge_state infrastructure for now. Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200107185807.606999-5-boris.brezillon@collabora.com
2020-01-07drm/bridge: Patch atomic hooks to take a drm_bridge_stateBoris Brezillon
This way the drm_bridge_funcs interface is consistent with the rest of the subsystem. The only driver implementing those hooks (analogix DP) is patched too. Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed by: Jernej Skrabec <jernej.skrabec@siol.net> Tested-by: Jonas Karlman <jonas@kwiboo.se> [narmstrong: renamed state as old_bridge_state in rcar_lvds_atomic_disable] Link: https://patchwork.freedesktop.org/patch/msgid/20200106143409.32321-3-narmstrong@baylibre.com
2020-01-06drm/bridge: cdns: remove set but not used variable 'nlanes'yu kuai
Fixes gcc '-Wunused-but-set-variable' warning: drivers/gpu/drm/bridge/cdns-dsi.c: In function ‘cdns_dsi_mode2cfg’: drivers/gpu/drm/bridge/cdns-dsi.c:515:11: warning: variable ‘nlanes’ set but not used [-Wunused-but-set-variable] It is never used, and so can be removed. Signed-off-by: yu kuai <yukuai3@huawei.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191226121415.39483-1-yukuai3@huawei.com
2020-01-06drm/bridge: cdns: remove set but not used variable 'bpp'yu kuai
Fixes gcc '-Wunused-but-set-variable' warning: drivers/gpu/drm/bridge/cdns-dsi.c: In function ‘cdns_dsi_bridge_enable’: drivers/gpu/drm/bridge/cdns-dsi.c:788:6: warning: variable ‘bpp’ set but not used [-Wunused-but-set-variable] It is never used, and so can be removed. Signed-off-by: yu kuai <yukuai3@huawei.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191226121207.2099-1-yukuai3@huawei.com
2020-01-06drm: bridge: dw-hdmi: constify copied structureJulia Lawall
The dw_hdmi_hw structure is only copied into another structure, so make it const. The opportunity for this change was found using Coccinelle. Fixes: 7ed6c665e19d ("drm: bridge/dw_hdmi-ahb-audio: add audio driver") Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/1577864614-5543-16-git-send-email-Julia.Lawall@inria.fr
2020-01-03Merge tag 'drm-misc-next-2020-01-02' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-misc into drm-next drm-misc-next for v5.6: UAPI Changes: - Commandline parser: Add support for panel orientation, and per-mode options. - Fix IOCTL naming for dma-buf heaps. Cross-subsystem Changes: - Rename DMA_HEAP_IOC_ALLOC to DMA_HEAP_IOCTL_ALLOC before it becomes abi. - Change DMA-BUF system-heap's name to system. - Fix leak in error handling in dma_heap_ioctl(), and make a symbol static. - Fix udma-buf cpu access. - Fix ti devicetree bindings. Core Changes: - Add CTA-861-G modes with VIC >= 193. - Change error handling and remove bug_on in *drm_dev_init. - Export drm_panel_of_backlight() correctly once more. - Add support for lvds decoders. - Convert drm/client and drm/(gem-,)fb-helper to drm-device based logging and update logging todo. Driver Changes: - Add support for dsi/px30 to rockchip. - Add fb damage support to virtio. - Use dma_resv locking wrappers in vc4, msm, etnaviv. - Make functions in virtio static, and perform some simplifications. - Add suspend support to sun4i. - Add A64 mipi dsi support to sun4i. - Add runtime pm suspend to komeda. - Associated driver fixes. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/efc11139-1653-86bc-1b0f-0aefde219850@linux.intel.com
2019-12-18drm/bridge: lvds-codec: Simplify panel DT node localisationFabrizio Castro
The probe function needs to get ahold of the panel device tree node, and it achieves that by using a combination of of_graph_get_port_by_id, of_get_child_by_name, and of_graph_get_remote_port_parent. We can achieve the same goal by replacing those calls with a call to of_graph_get_remote_node these days. Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/1573660292-10629-8-git-send-email-fabrizio.castro@bp.renesas.com
2019-12-18drm/bridge: lvds-codec: Add "lvds-decoder" supportFabrizio Castro
Add support for transparent LVDS decoders by adding a new compatible string ("lvds-decoder") to the driver. This patch also adds member connector_type to struct lvds_codec, and that's because LVDS decoders have a different connector type from LVDS encoders. We fill this new member up with the data matching the compatible string. Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> [Fix pointer to int cast warning] Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191217230753.2999-1-laurent.pinchart+renesas@ideasonboard.com
2019-12-18drm/bridge: Repurpose lvds-encoder.cFabrizio Castro
lvds-encoder.c implementation is also suitable for LVDS decoders, not just LVDS encoders. Instead of creating a new driver for addressing support for transparent LVDS decoders, repurpose lvds-encoder.c for the greater good with this patch. This patch only "rebrands" the lvds-encoder.c driver, to make it suitable for hosting LVDS decoders support. The actual support for LVDS decoders will come with a later patch. Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/1573660292-10629-6-git-send-email-fabrizio.castro@bp.renesas.com
2019-12-17linux-next: build failure after merge of the drm-misc treeStephen Rothwell
Hi all, After merging the drm-misc tree, today's linux-next build (x86_64 allmodconfig) failed like this: drivers/gpu/drm/bridge/analogix/analogix-anx6345.c: In function 'anx6345_i2c_probe': drivers/gpu/drm/bridge/analogix/analogix-anx6345.c:738:30: error: implicit declaration of function 'i2c_new_dummy' [-Werror=implicit-function-declaration] 738 | anx6345->i2c_clients[i] = i2c_new_dummy(client->adapter, | ^~~~~~~~~~~~~ drivers/gpu/drm/bridge/analogix/analogix-anx6345.c:738:28: warning: assignment to 'struct i2c_client *' from 'int' makes pointer from integer without a cast [-Wint-conversion] 738 | anx6345->i2c_clients[i] = i2c_new_dummy(client->adapter, | ^ Caused by commit 6aa192698089 ("drm/bridge: Add Analogix anx6345 support") interacting with commit 2c2f00ab1641 ("i2c: remove i2c_new_dummy() API") From Linus' tree. I have applied the following fix up patch for today: From: Stephen Rothwell <sfr@canb.auug.org.au> Date: Mon, 16 Dec 2019 12:11:19 +1100 Subject: [PATCH] drm/bridge: fix up for removal of i2c_new_dummy() Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20191216122331.43c766f1@canb.auug.org.au
2019-12-17Merge tag 'drm-misc-next-2019-12-16' of ↵Daniel Vetter
git://anongit.freedesktop.org/drm/drm-misc into drm-next drm-misc-next for v5.6: UAPI Changes: - Add support for DMA-BUF HEAPS. Cross-subsystem Changes: - mipi dsi definition updates, pulled into drm-intel as well. - Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim. - Remove support for dma-buf kmap/kunmap. - Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well. Core Changes: - Small cleanups to ttm. - Fix SCDC definition. - Assorted cleanups to core. - Add todo to remove load/unload hooks, and use generic fbdev emulation. - Assorted documentation updates. - Use blocking ww lock in ttm fault handler. - Remove drm_fb_helper_fbdev_setup/teardown. - Warning fixes with W=1 for atomic. - Use drm_debug_enabled() instead of drm_debug flag testing in various drivers. - Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted) - Various kconfig indentation fixes in core and drivers. - Fix freeing transactions in dp-mst correctly. - Sean Paul is steping down as core maintainer. :-( - Add lockdep annotations for atomic locks vs dma-resv. - Prevent use-after-free for a bad job in drm_scheduler. - Fill out all block sizes in the P01x and P210 definitions. - Avoid division by zero in drm/rect, and fix bounds. - Add drm/rect selftests. - Add aspect ratio and alternate clocks for HDMI 4k modes. - Add todo for drm_framebuffer_funcs and fb_create cleanup. - Drop DRM_AUTH for prime import/export ioctls. - Clear DP-MST payload id tables downstream when initializating. - Fix for DSC throughput definition. - Add extra FEC definitions. - Fix fake offset in drm_gem_object_funs.mmap. - Stop using encoder->bridge in core directly - Handle bridge chaining slightly better. - Add backlight support to drm/panel, and use it in many panel drivers. - Increase max number of y420 modes from 128 to 256, as preparation to add the new modes. Driver Changes: - Small fixes all over. - Fix documentation in vkms. - Fix mmap_sem vs dma_resv in nouveau. - Small cleanup in komeda. - Add page flip support in gma500 for psb/cdv. - Add ddc symlink in the connector sysfs directory for many drivers. - Add support for analogic an6345, and fix small bugs in it. - Add atomic modesetting support to ast. - Fix radeon fault handler VMA race. - Switch udl to use generic shmem helpers. - Unconditional vblank handling for mcde. - Miscellaneous fixes to mcde. - Tweak debug output from komeda using debugfs. - Add gamma and color transform support to komeda for DOU-IPS. - Add support for sony acx424AKP panel. - Various small cleanups to gma500. - Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation. - Add support for Logic PD Type 28 panel. - Use drm_panel_* wrapper functions in exynos/tegra/msm. - Add devicetree bindings for generic DSI panels. - Don't include drm_pci.h directly in many drivers. - Add support for begin/end_cpu_access in udmabuf. - Stop using drm_get_pci_dev in gma500 and mga200. - Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access. - Add devfreq thermal support to panfrost. - Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager. - meson: Add support for OSD1 plane AFBC commit. - Stop displaying garbage when toggling ast primary plane on/off. - More cleanups and fixes to UDL. - Add D32 suport to komeda. - Remove globle copy of drm_dev in gma500. - Add support for Boe Himax8279d MIPI-DSI LCD panel. - Add support for ingenic JZ4770 panel. - Small null pointer deference fix in ingenic. - Remove support for the special tfp420 driver, as there is a generic way to do it. Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
2019-12-16drm/bridge/synopsys: dsi: move phy_ops callbacks around panel enablementHeiko Stuebner
If implementation-specific phy_ops need to be defined they probably should be enabled before trying to talk to the panel and disabled only after the panel was disabled. Right now they are enabled last and disabled first, so might make it impossible to talk to some panels - example for this being the px30 with an external Innosilicon dphy that needs the phy to be enabled to transfer commands to the panel. So move the calls appropriately. changed in v5: - rebased on top of 5.5-rc1 - merged with dsi timing change to prevent ordering conflicts Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Yannick Fertre <yannick.fertre@st.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191209143130.4553-3-heiko@sntech.de
2019-12-16drm/bridge/synopsys: dsi: driver-specific configuration of phy timingsHeiko Stuebner
The timing values for dw-dsi are often dependent on the used display and according to Philippe Cornu will most likely also depend on the used phy technology in the soc-specific implementation. To solve this and allow specific implementations to define them as needed add a new get_timing callback to phy_ops and call this from the dphy_timing function to retrieve the necessary values for the specific mode. Right now this handles the hs2lp + lp2hs where Rockchip SoCs need handling according to the phy speed, while STM seems to be ok with static values. changes in v5: - rebase on 5.5-rc1 - merge into px30 dsi series to prevent ordering conflicts changes in v4: - rebase to make it directly fit on top of drm-misc-next after all changes in v3: - check existence of phy_ops->get_timing in __dw_mipi_dsi_probe() - emit actual error when get_timing() call fails - add tags from Philippe and Yannick changes in v2: - add driver-specific handling, don't force all bridge users to use the same timings, as suggested by Philippe Suggested-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Yannick Fertre <yannick.fertre@st.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191209143130.4553-2-heiko@sntech.de
2019-12-10drm/bridge: panel: export drm_panel_bridge_connectorMihail Atanassov
The function was unexported and was causing link failures for pl111 (and probably the other user tve200) in a module build. Fixes: d383fb5f8add ("drm: get drm_bridge_panel connector via helper") Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Linux Walleij <linux.walleij@linaro.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191210144834.27491-1-mihail.atanassov@arm.com
2019-12-09drm/panel: decouple connector from drm_panelSam Ravnborg
To facilitate moving connector creation to display drivers, decouple the drm_connector from drm_panel. This patch adds a connector argument to drm_panel_get_modes(). All users of drm_panel_get_modes() already had the connector available, so updating users was trivial. With this patch drm_panel no longer keeps a reference to the drm_connector. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Jernej Skrabec <jernej.skrabec@siol.net> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Inki Dae <inki.dae@samsung.com> Cc: Joonyoung Shim <jy0922.shim@samsung.com> Cc: Seung-Woo Kim <sw0312.kim@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Kukjin Kim <kgene@kernel.org> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Stefan Agner <stefan@agner.ch> Cc: Alison Wang <alison.wang@nxp.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: CK Hu <ck.hu@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Cc: Sandy Huang <hjc@rock-chips.com> Cc: "Heiko Stübner" <heiko@sntech.de> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Torsten Duwe <duwe@lst.de> Cc: Vasily Khoruzhick <anarsoul@gmail.com> Cc: Icenowy Zheng <icenowy@aosc.io> Cc: Sean Paul <seanpaul@chromium.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Boris Brezillon <boris.brezillon@collabora.com> Cc: Hariprasad Kelam <hariprasad.kelam@gmail.com> Cc: Alexios Zavras <alexios.zavras@intel.com> Cc: Brian Masney <masneyb@onstation.org> Cc: Rob Clark <robdclark@chromium.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Allison Randal <allison@lohutok.net> Cc: Shayenne Moura <shayenneluzmoura@gmail.com> Cc: Abhinav Kumar <abhinavk@codeaurora.org> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-samsung-soc@vger.kernel.org Cc: linux-mediatek@lists.infradead.org Cc: linux-renesas-soc@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Cc: linux-tegra@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-7-sam@ravnborg.org
2019-12-09drm: get drm_bridge_panel connector via helperSam Ravnborg
The drm_connector created by drm_panel_bridge was accessed via drm_panel.connector. Avoid the detour around drm_panel by providing a simple get method. This avoids direct access to the connector field in drm_panel in the two users. The change is done in preparation for removal of drm_panel.connector. Update pl111 and tve200 to use the new helper. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Jernej Skrabec <jernej.skrabec@siol.net> Cc: Eric Anholt <eric@anholt.net> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-5-sam@ravnborg.org
2019-12-01Merge tag 'gpio-v5.5-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for the v5.5 kernel cycle Core changes: - Expose pull up/down flags for the GPIO character device to userspace. After clear input from the RaspberryPi and Beagle communities, it has been established that prototyping, industrial automation and make communities strongly need this feature, and as we want people to use the character device, we have implemented the simple pull up/down interface for GPIO lines. This means we can specify that a (chip-specific) pull up/down resistor can be enabled, but does not offer fine-grained control such as cases where the resistance of the same pull resistor can be controlled (yet). - Introduce devm_fwnode_gpiod_get_index() and start to phase out the old symbol devm_fwnode_get_index_gpiod_from_child(). - A bit of documentation clean-up work. - Introduce a define for GPIO line directions and deploy it in all GPIO drivers in the drivers/gpio directory. - Add a special callback to populate pin ranges when cooperating with the pin control subsystem and registering ranges as part of adding a gpiolib driver and a gpio_irq_chip driver at the same time. This is also deployed in the Intel Merrifield driver. New drivers: - RDA Micro GPIO controller. - XGS-iproc GPIO driver. Driver improvements: - Wake event and debounce support on the Tegra 186 driver. - Finalize the Aspeed SGPIO driver. - MPC8xxx uses a normal IRQ handler rather than a chained handler" * tag 'gpio-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (64 commits) gpio: Add TODO item for regmap helper Documentation: gpio: driver.rst: Fix warnings gpio: of: Fix bogus reference to gpiod_get_count() gpiolib: Grammar s/manager/managed/ gpio: lynxpoint: Setup correct IRQ handlers MAINTAINERS: Replace my email by one @kernel.org gpiolib: acpi: Make acpi_gpiochip_alloc_event always return AE_OK gpio/mpc8xxx: fix qoriq GPIO reading gpio: mpc8xxx: Don't overwrite default irq_set_type callback gpiolib: acpi: Print pin number on acpi_gpiochip_alloc_event errors gpiolib: fix coding style in gpiod_hog() drm/bridge: ti-tfp410: switch to using fwnode_gpiod_get_index() gpio: merrifield: Pass irqchip when adding gpiochip gpio: merrifield: Add GPIO <-> pin mapping ranges via callback gpiolib: Introduce ->add_pin_ranges() callback gpio: mmio: remove untrue leftover comment gpio: em: Use platform_get_irq() to obtain interrupts gpio: tegra186: Add debounce support gpio: tegra186: Program interrupt route mapping gpio: tegra186: Derive register offsets from bank/port ...
2019-11-27Merge tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm updates from Dave Airlie: "Lots of stuff in here, though it hasn't been too insane this merge apart from dealing with the security fun. uapi: - export different colorspace properties on DP vs HDMI - new fourcc for ARM 16x16 block format - syncobj: allow querying last submitted timeline value - DRM_FORMAT_BIG_ENDIAN defined as unsigned core: - allow using gem vma manager in ttm - connector/encoder/bridge doc fixes - allow more than 3 encoders for a connector - displayport mst suspend/resume reprobing support - vram lazy unmapping, uniform vram mm and gem vram - edid cleanups + AVI informframe bar info - displayport helpers - dpcd parser added dp_cec: - Allow a connector to be associated with a cec device ttm: - pipelining with no_gpu_wait fix - always keep BOs on the LRU sched: - allow free_job routine to sleep i915: - Block userptr from mappable GTT - i915 perf uapi versioning - OA stream dynamic reconfiguration - make context persistence optional - introduce DRM_I915_UNSTABLE Kconfig - add fake lmem testing under unstable - BT.2020 support for DP MSA - struct mutex elimination - Tigerlake display/PLL/power management improvements - Jasper Lake PCH support - refactor PMU for multiple GPUs - Icelake firmware update - Split out vga + switcheroo code amdgpu: - implement dma-buf import/export without helpers - vega20 RAS enablement - DC i2c over aux fixes - renoir GPU reset - DC HDCP support - BACO support for CI/VI asics - MSI-X support - Arcturus EEPROM support - Arcturus VCN encode support - VCN dynamic powergating on RV/RV2 amdkfd: - add navi12/14/renoir support to kfd radeon: - SI dpm fix ported from amdgpu - fix bad DMA on ppc platforms gma500: - memory leak fixes qxl: - convert to new gem mmap exynos: - build warning fix komeda: - add aclk sysfs attribute v3d: - userspace cleanup uapi change i810: - fix for underflow in dispatch ioctls ast: - refactor show_cursor mgag200: - refactor show_cursor arcgpu: - encoder finding improvements mediatek: - mipi_tx, dsi and partial crtc support for MT8183 SoC - rotation support meson: - add suspend/resume support omap: - misc refactors tegra: - DisplayPort support for Tegra 210, 186 and 194. - IOMMU-backed DMA API fixes panfrost: - fix lockdep issue - simplify devfreq integration rcar-du: - R8A774B1 SoC support - fixes for H2 ES2.0 sun4i: - vcc-dsi regulator support virtio-gpu: - vmexit vs spinlock fix - move to gem shmem helpers - handle large command buffers with cma" * tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm: (1855 commits) drm/amdgpu: invalidate mmhub semaphore workaround in gmc9/gmc10 drm/amdgpu: initialize vm_inv_eng0_sem for gfxhub and mmhub drm/amd/amdgpu/sriov skip RLCG s/r list for arcturus VF. drm/amd/amdgpu/sriov temporarily skip ras,dtm,hdcp for arcturus VF drm/amdgpu/gfx10: re-init clear state buffer after gpu reset merge fix for "ftrace: Rework event_create_dir()" drm/amdgpu: Update Arcturus golden registers drm/amdgpu/gfx10: fix out-of-bound mqd_backup array access drm/amdgpu/gfx10: explicitly wait for cp idle after halt/unhalt Revert "drm/amd/display: enable S/G for RAVEN chip" drm/amdgpu: disable gfxoff on original raven drm/amdgpu: remove experimental flag for Navi14 drm/amdgpu: disable gfxoff when using register read interface drm/amdgpu/powerplay: properly set PP_GFXOFF_MASK (v2) drm/amdgpu: fix bad DMA from INTERRUPT_CNTL2 drm/radeon: fix bad DMA from INTERRUPT_CNTL2 drm/amd/display: Fix debugfs on MST connectors drm/amdgpu/nv: add asic func for fetching vbios from rom directly drm/amdgpu: put flush_delayed_work at first drm/amdgpu/vcn2.5: fix the enc loop with hw fini ...
2019-11-22Merge branch 'asoc-5.5' into asoc-nextMark Brown
2019-11-20drm/bridge: Fix Kconfig indentationKrzysztof Kozlowski
Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like: $ sed -e 's/^ /\t/' -i */Kconfig Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20191120133634.11601-1-krzk@kernel.org
2019-11-13drm/bridge: ti-tfp410: switch to using fwnode_gpiod_get_index()Dmitry Torokhov
Instead of fwnode_get_named_gpiod() that I plan to hide away, let's use the new fwnode_gpiod_get_index() that mimics gpiod_get_index(), but works with arbitrary firmware node. Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-11-13drm/bridge: anx6345: Fix compilation breakage on systems without CONFIG_OFMaxime Ripard
The driver assumes that the platform uses the device tree, and thus relies on some fields (of_node) being declared in some structures (drm_bridge). This isn't true for all platforms, so make sure we can only compile the ANX6345 on platforms where DT support is selected. Cc: Torsten Duwe <duwe@lst.de> Fixes: 6aa192698089 ("drm/bridge: Add Analogix anx6345 support") Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20191112204551.541449-1-maxime@cerno.tech
2019-11-12drm/bridge: fix anx6345 compilation for v5.5Torsten Duwe
The anx6345 driver originally was copied from anx78xx.c, which has meanwhile seen a few changes. In particular, the removal of drm_dp_link helpers and the discontinuation to include drm_bridge.h from drm_crtc.h breaks compilation in linux-5.5. Apply equivalents of these changes to anx6345.c. Fixes: 6aa192698089 ("drm/bridge: Add Analogix anx6345 support") Signed-off-by: Torsten Duwe <duwe@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20191112175940.GA13539@lst.de
2019-11-08drm/bridge: Add Analogix anx6345 supportIcenowy Zheng
The ANX6345 is an ultra-low power DisplayPower/eDP transmitter designed for portable devices. This driver adds initial support for RGB to eDP mode, without HPD and interrupts. This is a configuration usually seen in eDP applications. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Torsten Duwe <duwe@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20191107135220.590D968BFE@verein.lst.de
2019-11-08drm/bridge: Prepare Analogix anx6345 supportTorsten Duwe
Add bit definitions required for the anx6345 and add a sanity check in anx_dp_aux_transfer. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Torsten Duwe <duwe@suse.de> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20191107135218.01C2168C4E@verein.lst.de
2019-11-08drm/bridge: extract some Analogix I2C DP common codeIcenowy Zheng
Some code can be shared within different DP bridges by Analogix. Extract them to analogix_dp. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Torsten Duwe <duwe@suse.de> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20191107135214.966BD68BFE@verein.lst.de
2019-11-08drm/bridge: split some definitions of ANX78xx to dedicated headersIcenowy Zheng
Some definitions currently in analogix-anx78xx.h are not restricted to the ANX78xx series, but also applicable to other DisplayPort transmitters by Analogix. Split out them to dedicated headers, and make analogix-anx78xx.h include them. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Torsten Duwe <duwe@suse.de> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20191107135212.4D41E68BE1@verein.lst.de
2019-11-08drm/bridge: move ANA78xx driver to analogix subdirectoryIcenowy Zheng
As ANA78xx chips are designed and produced by Analogix Semiconductor, Inc, move their driver codes into analogix subdirectory. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Torsten Duwe <duwe@suse.de> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20191107135202.2089C68BE1@verein.lst.de
2019-10-29drm: bridge: dw-hdmi: Report connector status using callbackCheng-Yi Chiang
Allow codec driver register callback function for plug event. The callback registration flow: dw-hdmi <--- hw-hdmi-i2s-audio <--- hdmi-codec dw-hdmi-i2s-audio implements hook_plugged_cb op so codec driver can register the callback. dw-hdmi exports a function dw_hdmi_set_plugged_cb so platform device can register the callback. When connector plug/unplug event happens, report this event using the callback. Make sure that audio and drm are using the single source of truth for connector status. Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Link: https://lore.kernel.org/r/20191028071930.145899-2-cychiang@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 13:43:45 +0000