| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 9f9eef9ec1a2b57d95a86fe81df758e8253a7766 ]
HDCP must disabled encryption and restart authentication after
waiting KSV for 5s.
The original method uses a counter in a waitting loop that may
wait much longer than it is supposed to.
Use time_after() for KSV wait timeout.
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-9-e0fdd4844703@ite.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0989c02c7a5c887c70afeae80c64d0291624e1a7 ]
When HDCP negotiation with a repeater device.
Checking SHA V' matching must retry 3 times before restarting HDCP.
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-8-e0fdd4844703@ite.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c01b0bae2f9e58f2fee0e811cb90d8331986554 ]
When starting HDCP authentication, HDCP encryption should be enabled
when R0'is checked.
Change encryption enables time at R0' ready.
The hardware HDCP engine trigger is changed and the repeater KSV fails
will restart HDCP.
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-6-e0fdd4844703@ite.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0fd2ff47d8c207fa3173661de04bb9e8201c0ad2 ]
When HDCP is activated,
a DisplayPort source receiving CP_IRQ from the sink
shall check Bstatus from DPCD and process the corresponding value
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-5-e0fdd4844703@ite.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 85597bc0d70c287ba41f17d14d3d857a38a3d727 ]
A HDCP source device shall support max downstream to 127 devices.
Change definition MAX_HDCP_DOWN_STREAM_COUNT to 127
KSVs shall save for DRM blocked devices check.
This results in struct it6505 growth by ~0.5 KiB.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-4-e0fdd4844703@ite.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 39ead6e02ea7d19b421e9d42299d4293fed3064e ]
Reading access to connector->eld can happen at the same time the
drm_edid_to_eld() updates the data. Take the newly added eld_mutex in
order to protect connector->eld from concurrent access.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-3-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e72bf423a60afd744d13e40ab2194044a3af5217 ]
Reading access to connector->eld can happen at the same time the
drm_edid_to_eld() updates the data. Take the newly added eld_mutex in
order to protect connector->eld from concurrent access.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241206-drm-connector-eld-mutex-v2-2-c9bce1ee8bea@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c14870218c14532b0f0a7805b96a4d3c92d06fb2 ]
The hardware AUX FIFO is 16 bytes
Change definition of AUX_FIFO_MAX_SIZE to 16
Fixes: b5c84a9edcd4 ("drm/bridge: add it6505 driver")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-1-e0fdd4844703@ite.corp-partner.google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 81adbd3ff21c1182e06aa02c6be0bfd9ea02d8e8 upstream.
The host_node pointer was assigned and freed in adv7533_parse_dt(), and
later, adv7533_attach_dsi() uses the same. Fix this use-after-free issue
by dropping of_node_put() in adv7533_parse_dt() and calling of_node_put()
in error path of probe() and also in the remove().
Fixes: 1e4d58cd7f88 ("drm/bridge: adv7533: Create a MIPI DSI device")
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119192040.152657-2-biju.das.jz@bp.renesas.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79d67c499c3f886202a40c5cb27e747e4fa4d738 upstream.
As per [1] and [2], ADV7535/7533 supports only 2-, 3-, or 4-lane. Drop
unsupported 1-lane.
[1] https://www.analog.com/media/en/technical-documentation/data-sheets/ADV7535.pdf
[2] https://www.analog.com/media/en/technical-documentation/data-sheets/ADV7533.pdf
Fixes: 1e4d58cd7f88 ("drm/bridge: adv7533: Create a MIPI DSI device")
Reported-by: Hien Huynh <hien.huynh.px@renesas.com>
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119192040.152657-4-biju.das.jz@bp.renesas.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 902806baf3c1e8383c1fe3ff0b6042b8cb5c2707 ]
AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
while updating Audio InfoFrame information and then set to 0 when done.
Otherwise partially updated Audio InfoFrames could be sent out. Two
cases where this rule were not followed are fixed:
- In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
before/after setting ADV7511_REG_AUDIO_INFOFRAME.
- In audio_startup() use the correct register for clearing
AUDIO_UPDATE bit.
The problem with corrupted audio infoframes were discovered by letting
a HDMI logic analyser check the output of ADV7535.
Note that this patchs replaces writing REG_GC(1) with
REG_INFOFRAME_UPDATE. Bit 5 of REG_GC(1) is positioned within field
GC_PP[3:0] and that field doesn't control audio infoframe and is read-
only. My conclusion therefore was that the author if this code meant to
clear bit 5 of REG_INFOFRAME_UPDATE from the very beginning.
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: 53c515befe28 ("drm/bridge: adv7511: Add Audio support")
Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119-adv7511-audio-info-frame-v4-1-4ae68e76c89c@axis.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1e2ab24cd708b1c864ff983ee1504c0a409d2f8e ]
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240902113320.903147-2-liaochen4@huawei.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c5f3f21728b069412e8072b8b1d0a3d9d3ab0265 ]
The IT6505 bridge chip has a active low reset line. Since it is a
"reset" and not an "enable" line, the GPIO should be asserted to
put it in reset and deasserted to bring it out of reset during
the power on sequence.
The polarity was inverted when the driver was first introduced, likely
because the device family that was targeted had an inverting level
shifter on the reset line.
The MT8186 Corsola devices already have the IT6505 in their device tree,
but the whole display pipeline is actually disabled and won't be enabled
until some remaining issues are sorted out. The other known user is
the MT8183 Kukui / Jacuzzi family; their device trees currently do not
have the IT6505 included.
Fix the polarity in the driver while there are no actual users.
Fixes: b5c84a9edcd4 ("drm/bridge: add it6505 driver")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029095411.657616-1-wenst@chromium.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8814444e62b8a8b573fba2cbbb327d5817b74eb0 ]
The spec of timing between IVDD/OVDD and SYSRTEN is 10ms, but SYSRSTN RC
circuit need at least 25ms for rising time, update for match spec
Signed-off-by: Kuro Chung <kuro.chung@ite.com.tw>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240604024405.1122488-1-kuro.chung@ite.com.tw
Stable-dep-of: c5f3f21728b0 ("drm/bridge: it6505: Fix inverted reset polarity")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2d343723c7e1f9f6d64f721f07cfdfc2993758d1 ]
When a display controller driver uses DRM_BRIDGE_ATTACH_NO_CONNECTOR,
tc358767 will behave properly and skip the creation of the connector.
However, tc_get_display_props(), which is used to find out about the DP
monitor and link, is only called from two places: .atomic_enable() and
tc_connector_get_modes(). The latter is only used when tc358767 creates
its own connector, i.e. when DRM_BRIDGE_ATTACH_NO_CONNECTOR is _not_
set.
Thus, the driver never finds out the link properties before get_edid()
is called. With num_lanes of 0 and link_rate of 0 there are not many
valid modes...
Fix this by adding tc_get_display_props() call at the beginning of
get_edid(), so that we have up to date information before looking at the
modes.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Closes: https://lore.kernel.org/all/24282420-b4dd-45b3-bb1c-fc37fe4a8205@siemens.com/
Fixes: de5e6c027ae6 ("drm/bridge: tc358767: add drm_panel_bridge support")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231108-tc358767-v2-2-25c5f70a2159@ideasonboard.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 574c558ddb68591c9a4b7a95e45e935ab22c0fc6 ]
The bridge might miss the display change events when it's powered off.
This happens when a user changes the external monitor when the system
is suspended and the embedded controller doesn't not wake AP up.
It's also observed that one DP-to-HDMI bridge doesn't work correctly
when there is no EDID read after it is powered on.
Drop the cache to force an EDID read after system resume to fix this.
Fixes: 11feaef69d0c ("drm/bridge: it6505: Add caching for EDID")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926092931.3870342-3-treapking@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 00ae002116a14c2e6a342c4c9ae080cdbb9b4b21 ]
The bridge might miss the display change events when it's powered off.
This happens when a user changes the external monitor when the system
is suspended and the embedded controller doesn't not wake AP up.
It's also observed that one DP-to-HDMI bridge doesn't work correctly
when there is no EDID read after it is powered on.
Drop the cache to force an EDID read after system resume to fix this.
Fixes: 8bdfc5dae4e3 ("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926092931.3870342-2-treapking@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 32c4514455b2b8fde506f8c0962f15c7e4c26f1d upstream.
Wait for the command transmission to be completed in the DSI transfer
function polling for the dc_start bit to go back to idle state after the
transmission is started.
This is documented in the datasheet and failures to do so lead to
commands corruption.
Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240926141246.48282-1-francesco@dolcini.it
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926141246.48282-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aeedaee5ef5468caf59e2bb1265c2116e0c9a924 ]
Moved IRQ registration down to end of adv7511_probe().
If an IRQ already is pending during adv7511_probe
(before adv7511_cec_init) then cec_received_msg_ts
could crash using uninitialized data:
Unable to handle kernel read from unreadable memory at virtual address 00000000000003d5
Internal error: Oops: 96000004 [#1] PREEMPT_RT SMP
Call trace:
cec_received_msg_ts+0x48/0x990 [cec]
adv7511_cec_irq_process+0x1cc/0x308 [adv7511]
adv7511_irq_process+0xd8/0x120 [adv7511]
adv7511_irq_handler+0x1c/0x30 [adv7511]
irq_thread_fn+0x30/0xa0
irq_thread+0x14c/0x238
kthread+0x190/0x1a8
Fixes: 3b1b975003e4 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Mads Bligaard Nielsen <bli@bang-olufsen.dk>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240219-adv7511-cec-irq-crash-fix-v2-1-245e53c4b96f@bang-olufsen.dk
(cherry picked from commit aeedaee5ef5468caf59e2bb1265c2116e0c9a924)
[Harshit: CVE-2024-26876; Resolve conflicts due to missing commit:
c75551214858 ("drm: adv7511: Add has_dsi variable to struct
adv7511_chip_info") in 6.6.y and adv7511_chip_info struct is also not
defined]
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fe828fbd87786238b30f44cafd698d975d956c97 ]
If the bridge is attached with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag set,
this driver won't initialize a connector and hence display mode won't be
validated in drm_connector_helper_funcs::mode_valid(). So, move the mode
validation from drm_connector_helper_funcs::mode_valid() to
drm_bridge_funcs::mode_valid(), because the mode validation is always done
for the bridge.
Fixes: 30e2ae943c26 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240813091637.1054586-1-victor.liu@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
via IRQ
[ Upstream commit 162e48cb1d84c2c966b649b8ac5c9d4f75f6d44f ]
Make sure the connector is fully initialized before signalling any
HPD events via drm_kms_helper_hotplug_event(), otherwise this may
lead to NULL pointer dereference.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240531203333.277476-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9fc75c40faa29df14ba16066be6bdfaea9f39ce4 ]
The DSI horizontal timing calculations done by the driver seem to often
lead to underflows or overflows, depending on the videomode.
There are two main things the current driver doesn't seem to get right:
DSI HSW and HFP, and VSDly. However, even following Toshiba's
documentation it seems we don't always get a working display.
This patch attempts to fix the horizontal timings for DSI event mode, and
on a system with a DSI->HDMI encoder, a lot of standard HDMI modes now
seem to work. The work relies on Toshiba's documentation, but also quite
a bit on empirical testing.
This also adds timing related debug prints to make it easier to improve
on this later.
The DSI pulse mode has only been tested with a fixed-resolution panel,
which limits the testing of different modes on DSI pulse mode. However,
as the VSDly calculation also affects pulse mode, so this might cause a
regression.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-12-31725f008a50@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e82290a2e0e8ec5e836ecad1ca025021b3855c2d upstream.
Address only transactions without any data are valid and should not
be flagged as short transactions. Simply return the message size when
no transaction errors occured.
CC: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240318203925.2837689-1-l.stach@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 484436ec5c2bffe8f346a09ae1cbc4cbf5e50005 ]
When the system power resumes, the TTL input of IT6505 may experience
some noise before the video signal stabilizes, necessitating a video
reset. This patch is implemented to prevent a loop of video error
interrupts, which can occur when a video reset in the video FIFO error
interrupt triggers another such interrupt. The patch processes the SCDT
and FIFO error interrupts simultaneously and ignores any video FIFO
error interrupts caused by a video reset.
Fixes: b5c84a9edcd4 ("drm/bridge: add it6505 driver")
Signed-off-by: Kuro Chung <kuro.chung@ite.com.tw>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240522065528.1053439-1-kuro.chung@ite.com.tw
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ca077ff8cac5af8a5a3c476983a6dd54aa3511b7 ]
To have better compatibility for DP sink, there is a retry mechanism
for the link training process to switch between different training process.
The original driver code doesn't reset the retry counter when training
state is pass. If the system triggers link training over 3 times,
there will be a chance to causes the driver to use the wrong training
method and return a training fail result.
To Fix this, we reset the retry counter when training state is pass
each time.
Signed-off-by: Allen Chen <allen.chen@ite.corp-partner.google.com>
Signed-off-by: xiazhengqiao <xiazhengqiao@huaqin.corp-partner.google.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231221093057.7073-1-xiazhengqiao@huaqin.corp-partner.google.com
Stable-dep-of: 484436ec5c2b ("drm/bridge: it6505: fix hibernate to resume no display issue")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ce62600c4dbee8d43b02277669dd91785a9b81d9 ]
Device managed panel bridge wrappers are created by calling to
drm_panel_bridge_add_typed() and registering a release handler for
clean-up when the device gets unbound.
Since the memory for this bridge is also managed and linked to the panel
device, the release function should not try to free that memory.
Moreover, the call to devm_kfree() inside drm_panel_bridge_remove() will
fail in this case and emit a warning because the panel bridge resource
is no longer on the device resources list (it has been removed from
there before the call to release handlers).
Fixes: 67022227ffb1 ("drm/bridge: Add a devm_ allocator for panel bridge.")
Signed-off-by: Adam Miotk <adam.miotk@arm.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610102739.139852-1-adam.miotk@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ad81feb5b6f1f5461641706376dcf7a9914ed2e7 ]
This reverts commit 8a91b29f1f50ce7742cdbe5cf11d17f128511f3f.
The regulator_disable() added by the original commit solves one kind of
regulator imbalance but adds another one as it allows the regulator to be
disabled one more time than it is enabled in the following scenario:
1. Start video pipeline -> sn65dsi83_atomic_pre_enable -> regulator_enable
2. PLL lock fails -> regulator_disable
3. Stop video pipeline -> sn65dsi83_atomic_disable -> regulator_disable
The reason is clear from the code flow, which looks like this (after
removing unrelated code):
static void sn65dsi83_atomic_pre_enable()
{
regulator_enable(ctx->vcc);
if (PLL failed locking) {
regulator_disable(ctx->vcc); <---- added by patch being reverted
return;
}
}
static void sn65dsi83_atomic_disable()
{
regulator_disable(ctx->vcc);
}
The use case for introducing the additional regulator_disable() was
removing the module for debugging (see link below for the discussion). If
the module is removed after a .atomic_pre_enable, i.e. with an active
pipeline from the DRM point of view, .atomic_disable is not called and thus
the regulator would not be disabled.
According to the discussion however there is no actual use case for
removing the module with an active pipeline, except for
debugging/development.
On the other hand, the occurrence of a PLL lock failure is possible due to
any physical reason (e.g. a temporary hardware failure for electrical
reasons) so handling it gracefully should be supported. As there is no way
for .atomic[_pre]_enable to report an error to the core, the only clean way
to support it is calling regulator_disabled() only in .atomic_disable,
unconditionally, as it was before.
Link: https://lore.kernel.org/all/15244220.uLZWGnKmhe@steina-w/
Fixes: 8a91b29f1f50 ("drm/bridge: ti-sn65dsi83: Fix enable error path")
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240426122259.46808-1-luca.ceresoli@bootlin.com
(cherry picked from commit 2940ee03b23281071620dda1d790cd644dabd394)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 30ea09a182cb37c4921b9d477ed18107befe6d78 ]
The bridge always uses 24bpp internally. Therefore, for jeida-18
mapping we need to discard the lowest two bits for each channel and thus
starting with LV_[RGB]2. jeida-24 has the same mapping but uses four
lanes instead of three, with the forth pair transmitting the lowest two
bits of each channel. Thus, the mapping between jeida-18 and jeida-24
is actually the same, except that one channel is turned off (by
selecting the RGB666 format in VPCTRL).
While at it, remove the bogus comment about the hardware default because
the default is overwritten in any case.
Tested with a jeida-18 display (Evervision VGG644804).
Fixes: b26975593b17 ("display/drm/bridge: TC358775 DSI/LVDS driver")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240225062008.33191-5-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a665b4e60369867cddf50f37f16169a3e2f434ad ]
Previously, the audio status was not updated during detection, leading
to a persistent audio despite hot plugging events. To resolve this
issue, update the audio status during detection.
Fixes: 566fef1226c1 ("drm/bridge: anx7625: add HDMI audio function")
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416-anx7625-v3-1-f916ae31bdd7@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 24f4f575214de776539d346b99b8717bffa8ebba ]
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Also move the "failed to attach" error message so that it's only printed
when the devm_mipi_dsi_attach() call fails.
Fixes: 6352cd451ddb ("drm: bridge: Add TI DLPC3433 DSI to DMD bridge")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-7-619a28148e5c@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 272377aa0e3dddeec3f568c8bb9d12c7a79d8ef5 ]
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: b26975593b17 ("display/drm/bridge: TC358775 DSI/LVDS driver")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-6-619a28148e5c@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6d9e877cde7e9b516a9a99751b8222c87557436d ]
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 0cbbd5b1a012 ("drm: bridge: add support for lontium LT9611UXC bridge")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-5-619a28148e5c@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd0a2c6a081ff67007323725b9ff07d9934b1ed8 ]
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 23278bf54afe ("drm/bridge: Introduce LT9611 DSI to HDMI bridge")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-4-619a28148e5c@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b3b4695ff47c4964d4ccb930890c9ffd8e455e20 ]
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 30e2ae943c26 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-3-619a28148e5c@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 275fafe58faa7fdb10fa245412696ecef676aac5 ]
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 8dde6f7452a1 ("drm: bridge: icn6211: Add I2C configuration support")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-2-619a28148e5c@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ef4a9204d594fe959cdbc7418273caf4001535c8 ]
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 269332997a16 ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-1-619a28148e5c@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 935a92a1c400285545198ca2800a4c6c519c650a ]
In cdns_mhdp_atomic_enable(), the return value of drm_mode_duplicate() is
assigned to mhdp_state->current_mode, and there is a dereference of it in
drm_mode_set_name(), which will lead to a NULL pointer dereference on
failure of drm_mode_duplicate().
Fix this bug add a check of mhdp_state->current_mode.
Fixes: fb43aa0acdfd ("drm: bridge: Add support for Cadence MHDP8546 DPI/DP bridge")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240408125810.21899-1-amishin@t-argos.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 171b711b26cce208bb628526b1b368aeec7b6fa4 ]
The .get_modes() hooks aren't supposed to return negative error
codes. Return 0 for no modes, whatever the reason.
Cc: Adrien Grassein <adrien.grassein@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/dcdddcbcb64b6f6cdc55022ee50c10dee8ddbc3d.1709913674.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 29e032296da5d6294378ffa8bad8e976c5aadbf5 ]
If EDID read fails, clear the EDID property.
Cc: Adrien Grassein <adrien.grassein@gmail.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/2080adaadf4bba3d85f58c42c065caf9aad9a4ef.1706038510.git.jani.nikula@intel.com
Stable-dep-of: 171b711b26cc ("drm/bridge: lt8912b: do not return negative values from .get_modes()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 60d1fe1a7f302cc1151b155ac2d134db59bb1420 ]
Prefer using the struct drm_edid based functions.
cc: Adrien Grassein <adrien.grassein@gmail.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/32c9b52fe6fa7cbad6bfd0ff00041876977e02ea.1706038510.git.jani.nikula@intel.com
Stable-dep-of: 171b711b26cc ("drm/bridge: lt8912b: do not return negative values from .get_modes()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3af7053de3f685c96158373bc234b2feca1f160 ]
Polling firmware HPD GPIO status, set HPD irq detect window to 2ms
after firmware HPD GPIO initial done
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231120091038.284825-2-xji@analogixsemi.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ff3d5d04db07e5374758baa7e877fde8d683ebab ]
The FORCE_STOP_STATE bit is unsuitable to force the DSI link into LP-11
mode. It seems the bridge internally queues DSI packets and when the
FORCE_STOP_STATE bit is cleared, they are sent in close succession
without any useful timing (this also means that the DSI lanes won't go
into LP-11 mode). The length of this gibberish varies between 1ms and
5ms. This sometimes breaks an attached bridge (TI SN65DSI84 in this
case). In our case, the bridge will fail in about 1 per 500 reboots.
The FORCE_STOP_STATE handling was introduced to have the DSI lanes in
LP-11 state during the .pre_enable phase. But as it turns out, none of
this is needed at all. Between samsung_dsim_init() and
samsung_dsim_set_display_enable() the lanes are already in LP-11 mode.
The code as it was before commit 20c827683de0 ("drm: bridge:
samsung-dsim: Fix init during host transfer") and 0c14d3130654 ("drm:
bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec") was correct
in this regard.
This patch basically reverts both commits. It was tested on an i.MX8M
SoC with an SN65DSI84 bridge. The signals were probed and the DSI
packets were decoded during initialization and link start-up. After this
patch the first DSI packet on the link is a VSYNC packet and the timing
is correct.
Command mode between .pre_enable and .enable was also briefly tested by
a quick hack. There was no DSI link partner which would have responded,
but it was made sure the DSI packet was send on the link. As a side
note, the command mode seems to just work in HS mode. I couldn't find
that the bridge will handle commands in LP mode.
Fixes: 20c827683de0 ("drm: bridge: samsung-dsim: Fix init during host transfer")
Fixes: 0c14d3130654 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231113164344.1612602-1-mwalle@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d5b7daa3c610af3f322ad1e91fc0c752ff32f0e ]
Similar to commit 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge
is suspended in .post_disable()"). Add a mutex to ensure that aux transfer
won't race with atomic_disable by holding the PM reference and prevent
the bridge from suspend.
Also we need to use pm_runtime_put_sync_suspend() to suspend the bridge
instead of idle with pm_runtime_put_sync().
Fixes: 3203e497eb76 ("drm/bridge: anx7625: Synchronously run runtime suspend.")
Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240118015916.2296741-1-hsinyi@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a20f1b02bafcbf5a32d96a1d4185d6981cf7d016 ]
After commit 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge
is suspended in .post_disable()"), if we hit the error case in
ps8640_aux_transfer() then we return without dropping the mutex. Fix
this oversight.
Fixes: 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge is suspended in .post_disable()")
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240117103502.1.Ib726a0184913925efc7e99c4d4fc801982e1bc24@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 26db46bc9c675e43230cc6accd110110a7654299 ]
The ps8640 bridge seems to expect everything to be power cycled at the
disable process, but sometimes ps8640_aux_transfer() holds the runtime
PM reference and prevents the bridge from suspend.
Prevent that by introducing a mutex lock between ps8640_aux_transfer()
and .post_disable() to make sure the bridge is really powered off.
Fixes: 826cff3f7ebb ("drm/bridge: parade-ps8640: Enable runtime power management")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240109120528.1292601-1-treapking@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3fc6c76a8d208d3955c9e64b382d0ff370bc61fc ]
The driver never unregisters the audio codec platform device, which can
lead to a crash on module reloading, nor does it handle the return value
from sii902x_audio_codec_init().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: ff5781634c41 ("drm/bridge: sii902x: Implement HDMI audio support")
Cc: Jyri Sarha <jsarha@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240103-si902x-fixes-v1-2-b9fd3e448411@ideasonboard.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103-si902x-fixes-v1-2-b9fd3e448411@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 08ac6f132dd77e40f786d8af51140c96c6d739c9 ]
A null pointer dereference crash has been observed rarely on TI
platforms using sii9022 bridge:
[ 53.271356] sii902x_get_edid+0x34/0x70 [sii902x]
[ 53.276066] sii902x_bridge_get_edid+0x14/0x20 [sii902x]
[ 53.281381] drm_bridge_get_edid+0x20/0x34 [drm]
[ 53.286305] drm_bridge_connector_get_modes+0x8c/0xcc [drm_kms_helper]
[ 53.292955] drm_helper_probe_single_connector_modes+0x190/0x538 [drm_kms_helper]
[ 53.300510] drm_client_modeset_probe+0x1f0/0xbd4 [drm]
[ 53.305958] __drm_fb_helper_initial_config_and_unlock+0x50/0x510 [drm_kms_helper]
[ 53.313611] drm_fb_helper_initial_config+0x48/0x58 [drm_kms_helper]
[ 53.320039] drm_fbdev_dma_client_hotplug+0x84/0xd4 [drm_dma_helper]
[ 53.326401] drm_client_register+0x5c/0xa0 [drm]
[ 53.331216] drm_fbdev_dma_setup+0xc8/0x13c [drm_dma_helper]
[ 53.336881] tidss_probe+0x128/0x264 [tidss]
[ 53.341174] platform_probe+0x68/0xc4
[ 53.344841] really_probe+0x188/0x3c4
[ 53.348501] __driver_probe_device+0x7c/0x16c
[ 53.352854] driver_probe_device+0x3c/0x10c
[ 53.357033] __device_attach_driver+0xbc/0x158
[ 53.361472] bus_for_each_drv+0x88/0xe8
[ 53.365303] __device_attach+0xa0/0x1b4
[ 53.369135] device_initial_probe+0x14/0x20
[ 53.373314] bus_probe_device+0xb0/0xb4
[ 53.377145] deferred_probe_work_func+0xcc/0x124
[ 53.381757] process_one_work+0x1f0/0x518
[ 53.385770] worker_thread+0x1e8/0x3dc
[ 53.389519] kthread+0x11c/0x120
[ 53.392750] ret_from_fork+0x10/0x20
The issue here is as follows:
- tidss probes, but is deferred as sii902x is still missing.
- sii902x starts probing and enters sii902x_init().
- sii902x calls drm_bridge_add(). Now the sii902x bridge is ready from
DRM's perspective.
- sii902x calls sii902x_audio_codec_init() and
platform_device_register_data()
- The registration of the audio platform device causes probing of the
deferred devices.
- tidss probes, which eventually causes sii902x_bridge_get_edid() to be
called.
- sii902x_bridge_get_edid() tries to use the i2c to read the edid.
However, the sii902x driver has not set up the i2c part yet, leading
to the crash.
Fix this by moving the drm_bridge_add() to the end of the
sii902x_init(), which is also at the very end of sii902x_probe().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: 21d808405fe4 ("drm/bridge/sii902x: Fix EDID readback")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 024b32db43a359e0ded3fcc6cd86247cbbed4224 ]
Unlike what is claimed in commit f5aa7d46b0ee ("drm/bridge:
parade-ps8640: Provide wait_hpd_asserted() in struct drm_dp_aux"), if
someone manually tries to do an AUX transfer (like via `i2cdump ${bus}
0x50 i`) while the panel is off we don't just get a simple transfer
error. Instead, the whole ps8640 gets thrown for a loop and goes into
a bad state.
Let's put the function to wait for the HPD (and the magical 50 ms
after first reset) back in when we're doing an AUX transfer. This
shouldn't actually make things much slower (assuming the panel is on)
because we should immediately poll and see the HPD high. Mostly this
is just an extra i2c transfer to the bridge.
Fixes: f5aa7d46b0ee ("drm/bridge: parade-ps8640: Provide wait_hpd_asserted() in struct drm_dp_aux")
Tested-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231221135548.1.I10f326a9305d57ad32cee7f8d9c60518c8be20fb@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 28d3d0696688154cc04983f343011d07bf0508e4 upstream.
The i2c_master_send/recv() functions return negative error codes or
they return "len" on success. So the error handling here can be written
as just normal checks for "if (ret < 0) return ret;". No need to
complicate things.
Btw, in this code the "len" parameter can never be zero, but even if
it were, then I feel like this would still be the best way to write it.
Fixes: 914437992876 ("drm/bridge: nxp-ptn3460: fix i2c_master_send() error checking")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/04242630-42d8-4920-8c67-24ac9db6b3c9@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 914437992876838662c968cb416f832110fb1093 upstream.
The i2c_master_send/recv() functions return negative error codes or the
number of bytes that were able to be sent/received. This code has
two problems. 1) Instead of checking if all the bytes were sent or
received, it checks that at least one byte was sent or received.
2) If there was a partial send/receive then we should return a negative
error code but this code returns success.
Fixes: a9fe713d7d45 ("drm/bridge: Add PTN3460 bridge driver")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/0cdc2dce-ca89-451a-9774-1482ab2f4762@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
