summaryrefslogtreecommitdiff
path: root/drivers/gpu/drm/bridge/sil-sii8620.c
AgeCommit message (Collapse)Author
2018-03-12drm/bridge/sii8620: use micro-USB cable detection logic to detect MHLMaciej Purski
Currently MHL chip must be turned on permanently to detect MHL cable. It duplicates micro-USB controller's (MUIC) functionality and consumes unnecessary power. Lets use extcon attached to MUIC to enable MHL chip only if it detects MHL cable. Signed-off-by: Maciej Purski <m.purski@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Acked-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
2017-11-22drm/edid: Allow HDMI infoframe without VIC or S3DVille Syrjälä
Appedix F of HDMI 2.0 says that some HDMI sink may fail to switch from 3D to 2D mode in a timely fashion if the source simply stops sending the HDMI infoframe. The suggested workaround is to keep sending the infoframe even when strictly not necessary (ie. no VIC and no S3D). HDMI 1.4 does allow for this behaviour, stating that sending the infoframe is optional in this case. The infoframe was first specified in HDMI 1.4, so in theory sinks predating that may not appreciate us sending an uknown infoframe their way. To avoid regressions let's try to determine if the sink supports the infoframe or not. Unfortunately there's no direct way to do that, so instead we'll just check if we managed to parse any HDMI 1.4 4k or stereo modes from the EDID, and if so we assume the sink will accept the infoframe. Also if the EDID contains the HDMI 2.0 HDMI Forum VSDB we can assume the sink is prepared to receive the infoframe. v2: Fix getting has_hdmi_infoframe from display_info Always fail constructing the infoframe if the display possibly can't handle it Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171113170427.4150-3-ville.syrjala@linux.intel.com
2017-11-16drm/bridge/sii8620: add DVI mode supportMaciej Purski
If the sink device is in HDMI mode, enable infoframe interrupt in scdt irq handle function else call start_video function immediately, because in DVI mode, there is no infoframe interrupt provided. Rename start_hdmi function to start_video and get rid of the old start_video function. In start_video, if the sink is DVI and mode is MHL1 or MHl2, write appropriate values to registers else the path should remain the same as in HDMI mode. Signed-off-by: Maciej Purski <m.purski@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1510224822-7732-1-git-send-email-m.purski@samsung.com
2017-11-16drm/bridge/sii8620: filter unsupported modesMarek Szyprowski
The maximum pixel clock depends on the version of the connected MHL adapter. Add mode_valid callback to filter out modes with too high pixel clock to avoid failure in mode_fixup later. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171109102831.19844-1-m.szyprowski@samsung.com
2017-10-11drm/bridge/sii8620: add remote control supportMaciej Purski
MHL specification defines Remote Control Protocol(RCP) to send input events between MHL devices. The driver now recognizes RCP messages and reacts to them by reporting key events to input subsystem, allowing a user to control a device using TV remote control. Signed-off-by: Maciej Purski <m.purski@samsung.com> Acked-by: Sean Young <sean@mess.org> Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1503565087-19730-1-git-send-email-m.purski@samsung.com
2017-08-24drm/bridge/sii8620: Fix memory corruptionMaciej Purski
Function sii8620_mt_read_devcap_reg_recv() used to read array index from a wrong msg register, which caused writing out of array bounds. It led to writing on other fields of struct sii8620. Signed-off-by: Maciej Purski <m.purski@samsung.com> Fixes: e9c6da270 ("drm/bridge/sii8620: add reading device capability registers") Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1503311571-25819-1-git-send-email-m.purski@samsung.com
2017-02-23drm/bridge/sii8620: add missing error handling in probeAndrzej Hajda
devm_request_threaded_irq result should be checked for errors. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/1487764057-23362-1-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: enable interlace modesAndrzej Hajda
Bug in DECON(CRTC) driver prevented interlace modes from proper work. Since DECON is fixed interlace modes can be enabled in MHL. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-26-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: enable MHL3 mode if possibleAndrzej Hajda
Since all sub-protocols of MHL3 are already supported MHL3 mode can be enabled. With this patch it is possible to use packed pixel modes and clocks up to 300MHz - 1920x1080@60Hz and 4K modes. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-25-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: add HSIC initialization codeAndrzej Hajda
In case of MHL3 HSIC should be initialized. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-24-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: improve gen2 write burst IRQ routineAndrzej Hajda
The patch adds code to report back feature complete IRQ, and code to read and drop burst writes from peer. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-23-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: send EMSC features on requestAndrzej Hajda
Device should report to the peer which features are really supported. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-22-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: rewrite hdmi start sequenceAndrzej Hajda
MHL3 protocol requires registry adjustments depending on chosen video mode. Necessary information is gathered in mode_fixup callback. In case of HDMI video modes driver should also send special AVI and MHL3 infoframes. The patch introduces generic helpers for handling MHL3 infoframes, in case of appearance of other users of MHL3 infoframes these function can be moved to common library. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-21-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: fix disconnect sequenceAndrzej Hajda
The patch allows to avoid rare cases when discovery fails. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-19-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: split EDID read and write codeAndrzej Hajda
MHL3 requires that after reading EDID from the sink source should ask peer for features. To make both protocols happy the patch splits the code accordingly. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-18-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: add delay during cbus resetAndrzej Hajda
Without delay CBUS sometimes was not reset properly. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-17-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: do not stop MHL output when TMDS input is stoppedAndrzej Hajda
Stopping output causes full re-detection of the sink and slows down the process. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-16-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: set gen2 write burst before sending MSC commandAndrzej Hajda
Write burst should be enabled for MHL_INT_RC_FEAT_REQ and disabled for other commands. The patch moves functions up and adds delay setting for MHL3 burst mode. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-15-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: abstract out sink detection codeAndrzej Hajda
MHL1 and MHL3 have different initialization paths. To make both protocols happy sink detection is put into continuation after link mode enablement. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-14-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: fix initialization sequence for MHL2 receiversAndrzej Hajda
MHL2 receiver require disabling transmitter on initialization. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-13-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: fix MSC message removalAndrzej Hajda
Messages queue can be cleaned up by message callbacks, to avoid repeated removal of current message it should be removed from the queue before calling these callbacks. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-12-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: remove spare CBUS bring-up sequenceAndrzej Hajda
In case of MHL3 CBUS is bring-up already in sii8620_got_ecbus_speed. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-11-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: fix peer device capabilities read codeAndrzej Hajda
Peer capabilities should be read differently depending on protocol version. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-10-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: respond to feature requestsAndrzej Hajda
MHL3 protocol requires device to respond to feature request from peer. This minimal answer fulfills the requirement and allows to continue negotiation. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-9-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: add support for burst eMSC transmissionsAndrzej Hajda
Burst transmissions are used in MHL3 mode negotiation. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-8-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: initial support for eCBUS-S modeAndrzej Hajda
The Single-ended eCBUS Mode (eCBUS-S) mode provides 60 Mb/s full-duplex bidirectional traffic for three channels: - CBUS data (CBUS1 channel), - High-bandwidth MHL data (eMSC channel), - tunneling data (T-CBUS channel). It is required to fully support MHL3 dongles. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-6-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: add continuations to messagesAndrzej Hajda
Due to asynchronous nature of MHL flow of execution is dispersed. Logical continuation of some actions happens after response of peer, i.e in interrupt handler. To simplify coding continuation mechanism has been added - it is now possible to provide continuation callback, which will be called after peer responds to given action. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-5-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: add reading device capability registersAndrzej Hajda
This functionality is necessary to implement MHL3 modes. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-4-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: add MHL3 mode check helperAndrzej Hajda
MHL3 modes differs significantly from MHL1 mode, this helper will be used frequently to clearly distinguish them. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-3-git-send-email-a.hajda@samsung.com
2017-02-02drm/bridge/sii8620: simplify MHL3 mode settingAndrzej Hajda
It is not necessary to set REG_COC_CTL0, REG_MHL_COC_CTL1 registers. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-2-git-send-email-a.hajda@samsung.com
2016-10-27drm/bridge: fix platform_no_drv_owner.cocci warningskbuild test robot
drivers/gpu/drm/bridge/sil-sii8620.c:1556:3-8: No need to set .owner here. The core will do it. Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci CC: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20161026165836.GA98766@lkp-sb04.lkp.intel.com
2016-10-27drm/bridge: fix semicolon.cocci warningskbuild test robot
drivers/gpu/drm/bridge/sil-sii8620.c:988:2-3: Unneeded semicolon Remove unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci CC: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/20161026165836.GA98907@lkp-sb04.lkp.intel.com
2016-10-26drm/bridge: add Silicon Image SiI8620 driverAndrzej Hajda
SiI8620 transmitter converts eTMDS/HDMI signal to MHL 3.0. It is controlled via I2C bus. Its interaction with other devices in video pipeline is performed mainly on HW level. The only interaction it does on device driver level is filtering-out unsupported video modes, it exposes drm_bridge interface to perform this operation. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1476085157-5266-1-git-send-email-a.hajda@samsung.com
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-03 00:17:30 +0000