| Age | Commit message (Collapse) | Author |
|---|
|
Remove code for reading the EDID and DPCD fields and use the helpers
instead.
Besides the obvious code reduction, other helpers are being added to the
core that could be used in this driver and will be good to be able to
use them instead of duplicating them.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Yakir Yang <ykk@rock-chips.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
|
|
Remove unneeded variables and assignments.
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[seanpaul added analogix prefix to subject]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1473863952-7658-4-git-send-email-yamada.masahiro@socionext.com
|
|
The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
sense to save the power consumption.
This patch have exported two symbols for platform driver to implement
the PSR function in hardware side:
- analogix_dp_active_psr()
- analogix_dp_inactive_psr()
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
|
|
Instead of just preparing the panel on bind, actually prepare/unprepare
during modeset/disable. The panel must be prepared in order to read hpd
status and edid, so we need to keep state around the prepares in order
to ensure we don't accidentally turn the panel off at the wrong time.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
|
|
The enum value of DP_IRQ_TYPE_HP_CABLE_IN is zero, but driver only
send drm hp event when the irq_type and the enum value is true.
if (irq_type & DP_IRQ_TYPE_HP_CABLE_IN || ...)
drm_helper_hpd_irq_event(dp->drm_dev);
So there would no drm hpd event when cable plug in, to fix that
just need to assign all hotplug enum with no-zero values.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
It's better to pass the connector to platform driver in .get_modes()
callback, just like what the .get_modes() helper function designed.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
|
|
RK3399 and RK3288 shared the same eDP IP controller, only some light
difference with VOP configure and GRF configure.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
|
|
As vendor document indicate, when REF_CLK bit set 0, then DP
phy's REF_CLK should switch to 24M source clock.
But due to IC PHY layout mistaken, some chips need to flip this
bit(like RK3288), and unfortunately they didn't indicate in the
DP version register. That's why we have to make this little hack.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
|
|
ANALOGIX_DP_PLL_REG_1
There're an register define error in ANALOGIX_DP_PLL_REG_1 which introduced
by commit bcec20fd5ad6 ("drm: bridge: analogix/dp: add some rk3288 special
registers setting").
The PHY PLL input clock source is selected by ANALOGIX_DP_PLL_REG_1
BIT 0, not BIT 1.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
It may caused a dead lock if we flush the hpd work in bridge disable time.
The normal flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
3. HPD work already in idle, no need to run the work function.
OUT <-- analogix_dp_bridge
OUT <-- DRM IOCTL
The dead lock flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
IN --> analogix_dp_hotplug
IN --> drm_helper_hpd_irq_event
3. Acquire mode_config lock (This lock already have been acquired in previous step 1)
** Dead Lock Now **
It's wrong to flush the hpd work in bridge->disable time, I guess the
original code just want to ensure the delay work must be finish before
encoder disabled.
The flush work in bridge disable time is try to ensure the HPD event
won't be missed before display card disabled, actually we can take a
fast respond way(interrupt thread) to update DRM HPD event to fix the
delay update and possible dead lock.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
Turn off the panel power in suspend time would help to reduce
power waste.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
Display Port monitor could support kinds of mode which indicate
in monitor edid, not just one single display resolution which
defined in panel or devivetree property display timing.
Note: Gustavo Padovan try to remove the controller and phy
power on function in bind time at bellow commit:
drm/exynos: do not start enabling DP at bind() phase
But for now driver need to read edid message in .get_modes()
function, so controller must be inited in bind time, so we
need to add controller init back.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
This change just make a little clean to make code more like
drm core expect, move hdp detect code from bridge->enable(),
and place them into connector->detect().
Note: Gustavo Padovan try to remove the controller and phy
power on function in bind time at bellow commit:
drm/exynos: do not start enabling DP at bind() phase
But for now the connector status don't hardcode to connected,
need to operate dp phy in .detect function, so we need to revert
parts if Gustavo Padovan's changes, add phy poweron
function in bind time.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
Some edp screen do not have hpd signal, so we can't just return
failed when hpd plug in detect failed.
This is an hardware property, so we need add a devicetree property
"analogix,need-force-hpd" to indicate this sutiation.
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
There are some IP limit on rk3288 that only support 4 physical lanes
of 2.7/1.6 Gbps/lane, so seprate them out by device_type flag.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
RK3288 need some special registers setting, we can separate
them out by the dev_type of plat_data.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
Both hsync/vsync polarity and interlace mode can be parsed from
drm display mode, and dynamic_range and ycbcr_coeff can be judge
by the video code.
But presumably Exynos still relies on the DT properties, so take
good use of mode_fixup() in to achieve the compatibility hacks.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
link count
link_rate and lane_count already configured in analogix_dp_set_link_train(),
so we don't need to config those repeatly after training finished, just
remove them out.
Beside Display Port 1.2 already support 5.4Gbps link rate, the maximum sets
would change from {1.62Gbps, 2.7Gbps} to {1.62Gbps, 2.7Gbps, 5.4Gbps}.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
Fix some obvious alignment problems, like alignment and line
over 80 characters problems, make this easy to be maintained
later.
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
In the original split we kept the register constants intact to keep the
diff small. Still the constants are Analogix-specific, so rename them now.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
|
|
Split the dp core driver from exynos directory to bridge directory,
and rename the core driver to analogix_dp_*, rename the platform
code to exynos_dp.
Beside the new analogix_dp driver would export six hooks.
"analogix_dp_bind()" and "analogix_dp_unbind()"
"analogix_dp_suspned()" and "analogix_dp_resume()"
"analogix_dp_detect()" and "analogix_dp_get_modes()"
The bind/unbind symbols is used for analogix platform driver to connect
with analogix_dp core driver. And the detect/get_modes is used for analogix
platform driver to init the connector.
They reason why connector need register in helper driver is rockchip drm
haven't implement the atomic API, but Exynos drm have implement it, so
there would need two different connector helper functions, that's why we
leave the connector register in helper driver.
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
