| Age | Commit message (Collapse) | Author |
|---|
|
Some panels trigger HPD irq due to noise, the HPD debounce
may be 1.8ms, exceeding the default irq detect window, ~1.4ms.
This patch set HPD irq detection window to 2ms to
tolerate the HPD noise.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220903130833.541463-1-xji@analogixsemi.com
|
|
As defined in the anx7625 dt-binding, the analogix,lane0-swing and
analogix,lane1-swing properties are uint8 arrays. Yet, the driver was
reading the array as if it were of uint32 and masking to 8-bit before
writing to the registers. This means that a devicetree written in
accordance to the dt-binding would have its values incorrectly parsed.
Fix the issue by reading the array as uint8 and storing them as uint8
internally, so that we can also drop the masking when writing the
registers.
Fixes: fd0310b6fe7d ("drm/bridge: anx7625: add MIPI DPI input feature")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220408013034.673418-1-nfraprado@collabora.com
|
|
Support reading edid through aux channel if panel is connected to aux
bus. Extend anx7625_aux_dpcd_trans() to implement aux transfer function:
1. panel is populated in devm_of_dp_aux_populate_ep_devices(), so move
anx7625_parse_dt() after.
2. Use pm runtime autosuspend since aux transfer function is called
multiple times when reading edid.
3. No-op if aux transfer length is 0.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220213103437.3363848-3-hsinyi@chromium.org
|
|
Send DPCD command to downstream before anx7625 power down,
let downstream monitor enter into standby mode.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220213103437.3363848-1-hsinyi@chromium.org
|
|
This patch provides HDCP setting interface for userspace to dynamic
enable/disable HDCP function.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106100127.1862702-2-xji@analogixsemi.com
|
|
Add bridge helper atomic conversion.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220106100127.1862702-1-xji@analogixsemi.com
|
|
Add audio HDMI codec function support, enable it through device true
flag "analogix,audio-enable".
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211104033857.2634562-1-xji@analogixsemi.com
|
|
The basic anx7625 driver only support MIPI DSI rx signal input.
This patch add MIPI DPI rx input configuration support, after apply
this patch, the driver can support DSI rx or DPI rx by adding
'bus-type' in DT.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211104033639.2634502-1-xji@analogixsemi.com
|
|
IVO panel require less input video clock variation than video clock
variation in DP CTS spec.
This patch decreases the K value of ANX7625 which will shrink eDP Tx
video clock variation to meet IVO panel's requirement.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210806104407.2208538-1-xji@analogixsemi.com
|
|
The driver originally use an atomic_t for keep track of the power
status, which makes the driver more complicated than needed, and has
some race condition as it's possible to have the power on and power off
sequence going at the same time.
This patch remove the usage of the atomic_t power_status, and use the
kernel runtime power management framework instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210517063553.554955-1-pihsun@chromium.org
|
|
When suspending the driver, anx7625_power_standby() will be called to
turn off reset-gpios and enable-gpios. However, power supplies are not
disabled. To save power, the driver can get the power supply regulators
and turn off them in anx7625_power_standby().
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210401053202.159302-2-hsinyi@chromium.org
|
|
The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
for portable device. It converts MIPI DSI/DPI to DisplayPort 1.3 4K.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/528b76c1a4f7b6ea85371bfae4bde389aec4bb24.1600423932.git.xji@analogixsemi.com
|
