| Age | Commit message (Collapse) | Author |
|---|
|
Avoids confusion in configurations.
v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This commit introduces a trace mechanism for struct pipe_ctx by adding a
middle layer struct in the amdgpu_dm_trace.h for capturing the most
important data from struct pipe_ctx and showing its data via tracepoint.
This tracepoint was added to dc.c and dcn10_hw_sequencer, however, it
can be added to other DCN architecture.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We should leave GSL if we're not doing immediate flip no matter if
we're doing pipe split or not
[How]
Check for updating GSL state whenever we're not doing
immediate flip
v2: Squash in build fix (Alex)
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
right side visual confirm is too thick due to it is 4 times of
left side (16 lines).
[How]
Change factor from 4 to 2.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Causes underflow regression
[How]
This reverts commit 99d1437aa0ac1f598e9aabca8bf0e8a40c38f8a1
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Underflow counter increases in AGM when performing some mode switches due
to timing sync, which is a known hardware issue.
[How]
Temporarily raise DPG height during timing sync so that underflow is not
reported.
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.
[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When forcing 3D mode in DAL, we set the right address to be the same as the
left address. We need to do the same for the meta addresses.
[How]
Program right meta to be same as left meta.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This should be programmed with timing rather than with odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.
This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
During driver unload, it is expected that p-state switching is supported.
If it's not supported, PMFW will hang due to a forced p-state switch. Even
if the current timing does not support p-state normally, we still want to
force allow because the worst that can happen is underflow. This will
match Navi10 behaviour.
[How]
- new hubbub func to control the force pstate register
- force allow when releasing display ownership
- registers are inaccessible after due to m_cgs.hwNotAvailable
- explicitly disable force signal during hw_init
- if driver is disabled and re-enabled, register not cleared otherwise
Also, remove DCN3 part of dcn10_init_hw, we will not be going back to it.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When running games or benchmarking with v-sync disabled, disabling
a plane (which is v-sync) can cause underflow. This is caused by
flips pending before pipe locking being applied after locks are
released and pipes could have been re-arranged or disconnected. This
could potentially apply a flip on incorrect pipe. Also, previous logic
of always locking pipes was unnecessary.
[How]
Only lock the pipes when there is a pipe being disabled to increase
efficiency. Before the pipes are locked, check that any pending flips
are cleared to ensure the flips are applied to the correct pipe.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update dc for vangogh support.
v2: fix compilation without DCN 301 set.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When running a game/benchmark with v-sync disabled, disabling a plane
(which is v-sync) can cause an underflow. This is due to flips that are
pending before pipe locking being applied after locks are released and
pipes have been re-arranged or disconnected. This can potentially apply
a flip on the incorrect pipe.
[How]
Check that any pending flips are cleared before locking any pipes to
ensure flips are applied on the correct pipes.
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
In DCN10 when a panel with YCbCr420 capability is connected via
USB-C to HDMI active dongle, no YCbCr420 option is listed in
Radeon settings.
[HOW]
Enable DP YCbCr420 mode support for DCN10
Signed-off-by: Gary Li <gary.li@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
When disabling DP video, the current REG_WAIT timeout
of 50ms is too low for certain cases with very high
VSYNC intervals.
[HOW]
Increase the timeout to 102ms, so that
refresh rates as low as 10Hz can be handled properly.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org>
|
|
[Why]
We dont's turn off backlight before power off eDP (VDD),
which is a violation of eDP specs.
[How]
Power off eDP backlight before power off eDP
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The ctx field of dc_transfer_func is not always populated and therefore
isn't reliable.
[How]
Remove dc context from dc_transfer_func
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
There are situations where we go from 2 pipe to 1 pipe in MPO, but this
isn't a pipe split being lost -- it's a plane disappearing in (i.e. video overlay
goes away) so we lose one pipe. In these situations we don't want to
disable the pipe in a separate operation from the rest of the pipe
programming sequence. We only want to disable a pipe in a
separate operation when we're actually disabling pipe split.
[How]
Make sure the pipe being lost has the same stream AND plane
as the old top pipe to ensure.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The function set_mst_bandwidth is poorly name since it isn't clear what
it does, and it also does not reflect any part of the allocation sequence
described in the DP spec.
[How]
Rename the function set_mst_bandwidth to set_throttled_vcp_size.
Signed-off-by: George Shen <george.shen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When pipe locks are being taken we wait for flip pending to clear first.
In some cases the pipe mapping is changed and the pending we're checking
for will never clear.
[How]
Don't check disabled pipes for flip pending.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
update_clocks might not be called on headless adapters. This means
DISPLAY_OFF may not be sent in headless cases.
[HOW]
If hardware is powered down on boot because it is headless (mode set
does not happen on that adapter) also send DISPLAY_OFF notification.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
These aren't stable on some platform configurations when driving
multiple displays, especially on higher resolution.
In particular the delay in asserting p-state and validating from
x86 outweights any power or performance benefit from the hardware
composition.
Under some configurations this will manifest itself as extreme stutter
or unresponsiveness especially when combined with cursor movement.
[How]
Disable these for now. Exposing overlays to userspace doesn't guarantee
that they'll be able to use them in any and all configurations and it's
part of the DRM contract to have userspace gracefully handle validation
failures when they occur.
Valdiation occurs as part of DC and this in particular affects RV, so
disable this in dcn10_global_validation.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This adds ARM64 support into the DCN. This mainly enables support
for Navi graphics cards. The dcn10 changes haven't been tested,
since I don't have the relevant hardware available, but there
is no way to conditionally disable them, so I've done them anyway.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Using FRAME_UPDATE will result in infopacket to be potentially updated
one frame late.
In commit stream scenarios for previously active stream, some stale
infopacket data from previous config might be erroneously sent out on
initial frame after stream is re-enabled.
[How]
Switch to using IMMEDIATE_UPDATE mode
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
format
[Why]
The format in MPCC should be 444
[How]
do not modify the mpcc black color according to pixel encoding format
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
For ver.4.4 and higher VBIOS contains default setting table.
{How]
Read Golden Settings Table from VBIOS, apply Aux tuning parameters.
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Struct dcn_dsc_state is used for reading current state
and parameters of DSC on a pipe, the target rate parameter
uses bytes per pixel even though its reading BITS_PER_PIXEL
register.
[How]
Changing it to Bits Per Pixel for consistency.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
to 60hz
[Why]
new calculated dispclk, dppclk are stored in
context->bw_ctx.bw.dcn.clk.dispclk_khz, dppclk_khz. Current dispclk,
dppclk are from dc->clk_mgr->clks.dispclk_khz. dcn_validate_bandwidth
compute new dispclk, dppclk. dispclk will put in use after
optimize_bandwidth when ramp_up_dispclk_with_dpp is called. There are
two places for dppclk be put in use. One location is the same as the
location as dispclk. Another is within update_dchubp_dpp which happens
between pre_bandwidth and optimize_bandwidth. dppclk updated within
update_dchubp_dpp will cause new clock values of dispclk and dppclk not
be in use at the same time. when clocks are decreased, this may cause
dppclk is lower than current configuration and let pipe stuck. for
example, eDP + external dp, change resolution of DP from 1920x1080x144hz
to 1280x960x60hz.
before change: dispclk = 337889 dppclk = 337889
change mode, dcn_validate_bandwidth calculate
dispclk = 143122 dppclk = 143122
update_dchubp_dpp be executed before dispclk be updated,
dispclk = 337889, but dppclk use new value dispclk /2 =
168944. this will cause pipe pstate warning issue.
[How]
between pre_bandwidth and optimize_bandwidth, while dispclk is going to
be decreased, keep dppclk = dispclk
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
In headless systems, if set mode is not called, hardware will not be
powered down on boot, causing HW/SW discrepancies. Powering down
hardware on boot will ensure SW state is accurate.
[HOW]
Set a timer callback on boot for 10 seconds. If set mode is not called
within that time, power down hardware. Otherwise, do not power down.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
To avoid s3 faild at the first cycle on renoir platform, it needs to
revert this patch:
drm/amd/display: add mechanism to skip DCN init
Signed-off-by: changfeng <Changfeng.Zhu@amd.com>
Ackedy-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Driver re-initialize registers already set in FW
[How]
Transfer init to FW
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If optimized init is done in FW. DCN init be skipped in driver. This
need to be communicated between driver and fw and maintain backwards
compatibility.
[How]
Use DMUB scratch 0 bit 2 to indicate optimized init done in fw and
use DMUB scatch 4 bit 0 to indicate drive supports the optimized flow
so FW will perform it.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Check max_tmds_clk_mhz firstly will restrict pixel clock under HDMI
1.4, thus HDMI2.0 port can't correctly support 4K 60Hz.
[HOW]
Fine tune the logic to check max_forum_tmds_clk_mhz firstly.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Currently DC doesn't check requested pixel clock against an EDID
specified TMDS max clock if it exists, passing modes that should fail
[HOW]
Add max TMDS clk to edid caps and perform check during validation
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
dc->hwss->edp_backlight_control is null, it would casue it only be off
main-link of eDP. It is not worng behavior for eDP power sequence off.
[how]
Must use hwseq->funcs.edp_backlight_control finction pointer for edp
backlight.
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Hw lock manager adds the ability to lock pipe, cursor, and dig in fw.
[How]
Send hw lock command to fw to lock pipe, cursor, and dig.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Need to guard some new DCN3.0 stuff.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add HW sequence programing for DCN3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support to program the DCN3 HUBP (Display to data fabric interface
pipe)
HW Blocks:
+--------++------+
| HUBBUB || HUBP |
+--------++------+
|
v
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support for programming the DCN3 OPTC (Output Timing Controller)
HW Blocks:
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support for the DIO (Display IO) block of DCN3, which entails our
stream and link encoders.
HW Blocks:
+--------+
| DIO |
+--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Unit enter to S4, garbage show on screen when do OPTC blank.
[How]
Wait for vblank then do OPTC blank
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Implement abm set_pipe call stacks
Have some asics speicifc call stacks for abm.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If VUPDATE_END is before VUPDATE_START the delay calculated can become
very large, causing a soft hang.
[How]
Take the absolute value of the difference between START and END.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We dropped the delay after changed the cursor functions locking the
entire pipe to locking just the CURSOR registers to fix page flip
stuttering - this introduced cursor stuttering instead, and an underflow
issue.
The cursor update can be delayed indefinitely if the cursor update
repeatedly happens right around VUPDATE.
The underflow issue can happen if we do a viewport update on a pipe
on the same frame where a cursor update happens around VUPDATE - the
old cursor registers are retained which can be in an invalid position.
This can cause a pipe hang and indefinite underflow.
[How]
The complex, ideal solution to the problem would be a software
triple buffering mechanism from the DM layer to program only one cursor
update per frame just before VUPDATE.
The simple workaround until we have that infrastructure in place is
this change - bring back the delay until VUPDATE before locking, but
with some corrections to the calculations.
This didn't work for all timings before because the calculation for
VUPDATE was wrong - it was using the offset from VSTARTUP instead and
didn't correctly handle the case where VUPDATE could be in the back
porch.
Add a new hardware sequencer function to use the existing helper to
calculate the real VUPDATE start and VUPDATE end - VUPDATE can last
multiple lines after all.
Change the udelay to incorporate the width of VUPDATE as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
One call was forcing stutter on instead of looking at the debug option.
Ensure we always check the debug option unless we want to force stutter
off.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
same with CL#1711022(correcting yuv420 black color in function dcn10_blank_pixel_data,program_scaler),
yuv420 black color also needs to be correct when enabling HDMI stream at the resume procedure.
[How]
correcting the yuv420 black color according to the way how 420 is packed :2 channels carry Y component,
1 channel alternate between Cb and Cr.
Signed-off-by: yanyan kang <Yanyan.Kang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
