| Age | Commit message (Collapse) | Author |
|---|
|
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
Add system suspend/resume capabilities to the pl330 driver so the amba
bus clock could be also unprepared to conserve energy.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Pull dmaengine fixes from Vinod Koul:
"We have couple of fixes for dmaengine queued up:
- dma mempcy fix for dma configuration of sun6i by Maxime
- pl330 fixes: First the fixing allocation for data buffers by Liviu
and then Jon's fixe for fifo width and usage"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: Fix allocation size for PL330 data buffer depth.
dmaengine: pl330: Limit MFIFO usage for memcpy to avoid exhausting entries
dmaengine: pl330: Align DMA memcpy operations to MFIFO width
dmaengine: sun6i: Fix memcpy operation
|
|
This patch adds runtime PM support to pl330 DMA engine driver.
The runtime power management for pl330 DMA driver allows gating of AMBA
clock (PDMA) in FSYS clock domain, when the device is not processing any
requests. This is necessary to enter low power modes on Exynos SoCs
(e.g. LPA on Exynos4x12 or W-AFTR on Exynos3250).
Runtime PM resuming of the device may happen in atomic context (during
call device_issue_pending()) so pm_runtime_irq_safe() is used. This will
lead only to disabling/enabling of the clock but this is sufficient for
gating the clock and for reducing energy usage.
Driver uses runtime PM callbacks from amba/bus.c driver only.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
same issue as commit 7f5ae3553685:
"Without DMA_PRIVATE the driver is not able to allocate more than one channel.
Since it uses dma_get_any_slave_channel that calls private_candidate, the
second allocation fails at
/* some channels are already publicly allocated */
"
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Lock taken when entering the function but unlock missing before it
returns.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The total size of the transfer was wrong in at_xdmac_prep_slave_sg()
resulting in bad computation of the transfer residue by
at_xdmac_tx_status().
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
According to the Atmel eXtended DMA controller datasheet, requesting a
DMA transfer flush for a channel is only revelant when this transfer is
source peripheral synchronized.
So we have to check this condition before requesting a channel flush by
writing the channel bit into the Global channel SoftWare Flush (GSWF)
register then waiting for flush to complete by monitoring the end of
Flush Interrupt Status (FIS) bit in the Channel Interrupt Status (CIS)
register.
Indeed, for non source peripheral synchronized transfer, writing the
channel bit into the GSWF register does nothing. Especially, the FIS bit
is never set into the CIS register. The former code looped forever
waiting for this bit to be set.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Remove chancnt affectation since it is done in dma_async_device_regiser.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
_relaxed version of readl and writel are not implemented on all
architecture so COMPILE_TEST has to be removed in order to not cause
some build failures.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
As documented in printk-formats.txt the dma_addr_t should be printed with
%pad specfiers. This way it works on all archs.
make.cross ARCH=s390
All warnings:
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_slave_sg':
>> drivers/dma/at_xdmac.c:621:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:621:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:628:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_cyclic':
>> drivers/dma/at_xdmac.c:663:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: buf_addr=0x%08x, buf_len=%d, period_len=%d, dir=%s, flags=0x%lx\n",
^
>> drivers/dma/at_xdmac.c:690:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:709:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:709:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:716:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
>> drivers/dma/at_xdmac.c:731:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_memcpy':
>> drivers/dma/at_xdmac.c:765:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: src=0x%08x, dest=0x%08x, len=%d, flags=0x%lx\n",
^
>> drivers/dma/at_xdmac.c:765:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: remaining_size=%u\n", __func__, remaining_size);
^
>> drivers/dma/at_xdmac.c:845:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:845:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:852:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_tx_status':
>> drivers/dma/at_xdmac.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
As documented in printk-formats.txt the size_t should be printed with
%zu/%zd specfiers. This way it works on all archs.
make.cross ARCH=avr32
All warnings:
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_cyclic':
>> drivers/dma/at_xdmac.c:663: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
>> drivers/dma/at_xdmac.c:663: warning: format '%d' expects type 'int', but argument 7 has type 'size_t'
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_memcpy':
>> drivers/dma/at_xdmac.c:765: warning: format '%d' expects type 'int', but argument 7 has type 'size_t'
>> drivers/dma/at_xdmac.c:794: warning: format '%u' expects type 'unsigned int', but argument 5 has type 'size_t'
>> drivers/dma/at_xdmac.c:815: warning: format '%u' expects type 'unsigned int', but argument 5 has type 'size_t'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This driver uses read_relaxed and writel_relaxed to read, write to IO
memory. the config defines COMPILE_TEST so gets compiled on different archs.
This causes issue as few archs like x86 etc don't define it.
So use readl/writel which is defined in all archs
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
drivers/dma/at_xdmac.c:702:3-4: Unneeded semicolon
Removes unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/dma/k3dma.c:790:12: warning: 'k3_dma_suspend' defined but not used [-Wunused-function]
drivers/dma/k3dma.c:806:12: warning: 'k3_dma_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/dma/sirf-dma.c:838:12: warning: 'sirfsoc_dma_pm_suspend' defined but not used [-Wunused-function]
drivers/dma/sirf-dma.c:879:12: warning: 'sirfsoc_dma_pm_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch simply adds a new DMATYPE for SAI which's included
in i.MX6 Solo X.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch fixes a race condition about a list of shdma-base driver.
If we don't apply this patch, a dma slave driver (especially a usb
peripheral driver) may not be able to start the transfer.
If a dma slave driver has a callback, __ld_cleanup() will call
the callback before this driver removes the list. After the callback,
since the return value of __ld_cleanup() is not zero,
shdma_chan_ld_cleanup() calls __ld_cleanup() again. And, __ld_clean()
will removes the list.
At this time, if a dma slave driver calls dmaengine_submit() before
this driver removes the list, this driver will set schan->pm_state
to SHDMA_PM_PENDING in shdma_tx_submit(). And then, even if a dma
slave driver calls dma_async_issue_pending(), this driver don't
start the transfer because the schan->pm_state is SHDMA_PM_PENDING
in shdma_issue_pending().
So, this patch adds a new condition in __ld_clean() to check if the
schan->pm_state is SHDMA_PM_PENDING or not.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
We currently have register offset information only for BAM IPs with revision
1.4.0. We add register offset table entries for the legacy (v1.3.0) version
of BAM IPs found on SoCs like APQ8064 and MSM8960.
The register offset table pointers are stored in DT data corresponding to the
BAM IP version specified in the compatible string.
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The BAM DMA IP comes in different versions. The register offset layout varies
among these versions. The layouts depend on which generation/family of SoCs they
belong to.
The current SoCs(like 8084, 8074) have a layout where the Top level registers
come in the beginning of the address range, followed by pipe and event
registers. The BAM revision numbers fall above 1.4.0.
The older SoCs (like 8064, 8960) have a layout where the pipe registers come
first, and the top level come later. These have BAM revision numbers lesser than
1.4.0.
It isn't suitable to have macros provide the register offsets with the layouts
changed. Future BAM revisions may have different register layouts too. The
register addresses are now calculated by referring a table which contains a base
offset and multipliers for pipe/evnt/ee registers.
We have a common function bam_addr() which computes addresses for all the
registers. When computing address of top level/ee registers, we pass 0 to the
pipe argument in addr() since they don't have any multiple instances.
Some of the unused register definitions are removed. We can add new registers as
we need them.
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The A23 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
A slight difference in sun8i is an undocumented register needs
to be toggled for dma to function.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch adds support for hardware parameters tied to compatible
strings, so similar hardware can reuse the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When platform_driver_probe() is not used, sdma_probe() can be called
by bind/unbind via sysfs. In addition, sdma_init() can be called by
sdma_probe(). Thus, __init annotation should be removed from sdma_init(),
Also, this patch fixes section mismatch warning.
WARNING: drivers/dma/built-in.o(.text+0xd6e4): Section mismatch in reference from the function sdma_probe() to the function
.init.text:sdma_init()
The function sdma_probe() references
the function __init sdma_init().
This is often because sdma_probe lacks a __init
annotation or the annotation of sdma_init is wrong.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Commit f6f2421c0a1c removed pl330_info structure by embedding it into
pl330_dmac structure, but did not ensure that the dmac->ddma.dev
pointer gets initialised before use. When dma_alloc_coherent() gets
called on arm64 a WARN() gets triggered due to dev being NULL.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at arch/arm64/mm/dma-mapping.c:49 __dma_alloc_coherent+0xd0/0xe0()
Use an actual device structure for DMA allocation
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.17.0+ #5
Call trace:
[<ffffffc000087f24>] dump_backtrace+0x0/0x130
[<ffffffc000088064>] show_stack+0x10/0x1c
[<ffffffc0004e8af8>] dump_stack+0x74/0xb8
[<ffffffc0000aa444>] warn_slowpath_common+0x8c/0xb4
[<ffffffc0000aa4b8>] warn_slowpath_fmt+0x4c/0x58
[<ffffffc000092580>] __dma_alloc_coherent+0xcc/0xe0
[<ffffffc000092734>] __dma_alloc_noncoherent+0x64/0x158
[<ffffffc000312cd8>] pl330_probe+0x650/0x8f0
[<ffffffc00030e1d4>] amba_probe+0xa0/0xc8
[<ffffffc000350240>] really_probe+0xc4/0x22c
[<ffffffc0003504b4>] __driver_attach+0xa0/0xa8
[<ffffffc00034e5fc>] bus_for_each_dev+0x54/0x98
[<ffffffc00034fd8c>] driver_attach+0x1c/0x28
[<ffffffc00034fa08>] bus_add_driver+0x14c/0x204
[<ffffffc000350b84>] driver_register+0x64/0x130
[<ffffffc00030dcf8>] amba_driver_register+0x50/0x5c
[<ffffffc0006a60d0>] pl330_driver_init+0x10/0x1c
[<ffffffc0000814ac>] do_one_initcall+0x88/0x19c
[<ffffffc00068dab8>] kernel_init_freeable+0x140/0x1e0
[<ffffffc0004e5e18>] kernel_init+0x10/0xd4
---[ end trace 76f2d47a444e523e ]---
(NULL device *): dmac_alloc_resources:1821 Can't allocate memory!
(NULL device *): Unable to create channels for DMAC
This patch will also ensure that any dev_err messages are printed
with the appropriate device name.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The datasheet for PL330 says that the data buffer value in the CRD
register is 10bits wide. However, the value stored is "minus one",
which the driver corrects for. Maximum value that the data buffer
depth can have is 1024 lines, which requires 11 bits for storage.
While making updates I found printing the peripheral ID as a hex
value to be more useful as the datasheet shows the values that way.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The MFIFO is shared by all channels so restrict each memcpy to it's fair
share. This is being over cautious, but without a global view of DMA
channel usage on a system it's not possible to come up with a more
optimum safe limit.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The algorithm used for programming the DMA Controller doesn't take into
consideration the requirements of transfers that are not aligned to the
bus width. This failure may result in DMA transferring one too few MFIFO
entries (so too few bytes are copied) or the DMA trying to write one too
many MFIFO entries and hanging because this is never provided.
See "MFIFO Usage Overview" chapter in the the TRM for "CoreLink DMA
Controller DMA-330", Revision r1p1.
We work around these shortcomings by making sure we pick a burst size
and length which ensures no bursts straddle an MFIFO entry.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
[squashed linker error "undefined reference to `__aeabi_uldivmod]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The prep_memcpy call was not setting any meaningful burst and width because it
was relying on the dma_slave_config was not set already.
Rework the needed conversion functions, and hardcode the width and burst to
use.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
On runtime PM aware platforms the DMA have to manage its own power state. This
patch enables runtime PM support and applies necessary calls wherever it's
needed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch modifies the icg field to match the description
as mentioned in the DMA Linux framework.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch adds a sanity check to see if frame_size is 1.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The segment list in a descriptor should be checked for empty, else
it will try to access invalid address for the first call. This
patch fixes this issue.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
[for nvidia]
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
New atmel DMA controller known as XDMAC, introduced with SAMA5D4
devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The horrible split between the low-level part of the edma support
and the dmaengine front-end driver causes problems on multiplatform
kernels. This is an attempt to improve the situation slightly
by only registering the dmaengine devices that are actually
present.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: add missing include of linux/dma-mapping.h]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
