| Age | Commit message (Collapse) | Author |
|---|
|
Expose through debugfs device telemetry data for QAT GEN4 devices.
This allows to gather metrics about the performance and the utilization
of a device. In particular, statistics on (1) the utilization of the
PCIe channel, (2) address translation, when SVA is enabled and (3) the
internal engines for crypto and data compression.
If telemetry is supported by the firmware, the driver allocates a DMA
region and a circular buffer. When telemetry is enabled, through the
`control` attribute in debugfs, the driver sends to the firmware, via
the admin interface, the `TL_START` command. This triggers the device to
periodically gather telemetry data from hardware registers and write it
into the DMA memory region. The device writes into the shared region
every second.
The driver, every 500ms, snapshots the DMA shared region into the
circular buffer. This is then used to compute basic metric
(min/max/average) on each counter, every time the `device_data` attribute
is queried.
Telemetry counters are exposed through debugfs in the folder
/sys/kernel/debug/qat_<device>_<BDF>/telemetry.
For details, refer to debugfs-driver-qat_telemetry in Documentation/ABI.
This patch is based on earlier work done by Wojciech Ziemba.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Extend the admin interface with two new public APIs to enable
and disable the telemetry feature: adf_send_admin_tl_start() and
adf_send_admin_tl_stop().
The first, sends to the firmware, through the ICP_QAT_FW_TL_START
message, the IO address where the firmware will write telemetry
metrics and a list of ring pairs (maximum 4) to be monitored.
It returns the number of accelerators of each type supported by
this hardware. After this message is sent, the firmware starts
periodically reporting telemetry data using by writing into the
dma buffer specified as input.
The second, sends the admin message ICP_QAT_FW_TL_STOP
which stops the reporting of telemetry data.
This patch is based on earlier work done by Wojciech Ziemba.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
GET_DEV() macro expansion relies on struct pci_dev being defined.
Include <linux/pci.h> at adf_accel_devices.h.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add support for 420xx devices by including a new device driver that
supports such devices, updates to the firmware loader and capabilities.
Compared to 4xxx devices, 420xx devices have more acceleration engines
(16 service engines and 1 admin) and support the wireless cipher
algorithms ZUC and Snow 3G.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Co-developed-by: Dong Xie <dong.xie@intel.com>
Signed-off-by: Dong Xie <dong.xie@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Relocate the structures adf_fw_objs and adf_fw_config from the file
adf_4xxx_hw_data.c to the newly created adf_fw_config.h.
These structures will be used by new device drivers.
This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Move logic that is common between QAT GEN4 accelerators to the
qat_common folder. This includes addresses of CSRs, setters and
configuration logic.
When moved, functions and defines have been renamed from 4XXX to GEN4.
Code specific to the device is moved to the file adf_gen4_hw_data.c.
Code related to configuration is moved to the newly created
adf_gen4_config.c.
This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add accel_dev as parameter of the function uof_get_num_objs().
This is in preparation for the introduction of the QAT 420xx driver as
it will allow to reconfigure the ae_mask when a configuration that does
not require all AEs is loaded on the device.
This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Move the function get_service_enabled() from adf_4xxx_hw_data.c to
adf_cfg_services.c and rename it as adf_get_service_enabled().
This function is not specific to the 4xxx and will be used by
other QAT drivers.
This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
There is a possibility that the function adf_devmgr_pci_to_accel_dev()
might return a NULL pointer.
Add a NULL pointer check in the function rp2srv_show().
Fixes: dbc8876dd873 ("crypto: qat - add rp2svc sysfs attribute")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: David Guckian <david.guckian@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If the function validate_user_input() returns an error, the error path
attempts to unlock an unacquired mutex.
Acquire the mutex before calling validate_user_input(). This is not
strictly necessary but simplifies the code.
Fixes: d9fb8408376e ("crypto: qat - add rate limiting feature to qat_4xxx")
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The input argument `sla_in` is a pointer to a structure that contains
the parameters of the SLA which is being added or updated.
If this pointer is NULL, the function should return an error as
the data required for the algorithm is not available.
By mistake, the logic jumps to the error path which dereferences
the pointer.
This results in a warnings reported by the static analyzer Smatch when
executed without a database:
drivers/crypto/intel/qat/qat_common/adf_rl.c:871 add_update_sla()
error: we previously assumed 'sla_in' could be null (see line 812)
This issue was not found in internal testing as the pointer cannot be
NULL. The function add_update_sla() is only called (indirectly) by
the rate limiting sysfs interface implementation in adf_sysfs_rl.c
which ensures that the data structure is allocated and valid. This is
also proven by the fact that Smatch executed with a database does not
report such error.
Fix it by returning with error if the pointer `sla_in` is NULL.
Fixes: d9fb8408376e ("crypto: qat - add rate limiting feature to qat_4xxx")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The qat_rl sysfs attribute group is registered within the adf_dev_start()
function, alongside other driver components.
If any of the functions preceding the group registration fails,
the adf_dev_start() function returns, and the caller, to undo the
operation, invokes adf_dev_stop() followed by adf_dev_shutdown().
However, the current flow lacks information about whether the
registration of the qat_rl attribute group was successful or not.
In cases where this condition is encountered, an error similar to
the following might be reported:
4xxx 0000:6b:00.0: Starting device qat_dev0
4xxx 0000:6b:00.0: qat_dev0 started 9 acceleration engines
4xxx 0000:6b:00.0: Failed to send init message
4xxx 0000:6b:00.0: Failed to start device qat_dev0
sysfs group 'qat_rl' not found for kobject '0000:6b:00.0'
...
sysfs_remove_groups+0x2d/0x50
adf_sysfs_rl_rm+0x44/0x70 [intel_qat]
adf_rl_stop+0x2d/0xb0 [intel_qat]
adf_dev_stop+0x33/0x1d0 [intel_qat]
adf_dev_down+0xf1/0x150 [intel_qat]
...
4xxx 0000:6b:00.0: qat_dev0 stopped 9 acceleration engines
4xxx 0000:6b:00.0: Resetting device qat_dev0
To prevent attempting to remove attributes from a group that has not
been added yet, a flag named 'sysfs_added' is introduced. This flag
is set to true upon the successful registration of the attribute group.
Fixes: d9fb8408376e ("crypto: qat - add rate limiting feature to qat_4xxx")
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The qat_ras sysfs attribute group is registered within the
adf_dev_start() function, alongside other driver components.
If any of the functions preceding the group registration fails,
the adf_dev_start() function returns, and the caller, to undo the
operation, invokes adf_dev_stop() followed by adf_dev_shutdown().
However, the current flow lacks information about whether the
registration of the qat_ras attribute group was successful or not.
In cases where this condition is encountered, an error similar to
the following might be reported:
4xxx 0000:6b:00.0: Starting device qat_dev0
4xxx 0000:6b:00.0: qat_dev0 started 9 acceleration engines
4xxx 0000:6b:00.0: Failed to send init message
4xxx 0000:6b:00.0: Failed to start device qat_dev0
sysfs group 'qat_ras' not found for kobject '0000:6b:00.0'
...
sysfs_remove_groups+0x29/0x50
adf_sysfs_stop_ras+0x4b/0x80 [intel_qat]
adf_dev_stop+0x43/0x1d0 [intel_qat]
adf_dev_down+0x4b/0x150 [intel_qat]
...
4xxx 0000:6b:00.0: qat_dev0 stopped 9 acceleration engines
4xxx 0000:6b:00.0: Resetting device qat_dev0
To prevent attempting to remove attributes from a group that has not
been added yet, a flag named 'sysfs_added' is introduced. This flag
is set to true upon the successful registration of the attribute group.
Fixes: 532d7f6bc458 ("crypto: qat - add error counters")
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The "ring" variable has an upper bounds check but nothing checks for
negatives. This code uses kstrtouint() already and it was obviously
intended to be declared as unsigned int. Make it so.
Fixes: dbc8876dd873 ("crypto: qat - add rp2svc sysfs attribute")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If a request has the flag CRYPTO_TFM_REQ_MAY_BACKLOG set, the function
qat_alg_send_message_maybacklog(), enqueues it in a backlog list if
either (1) there is already at least one request in the backlog list, or
(2) the HW ring is nearly full or (3) the enqueue to the HW ring fails.
If an interrupt occurs right before the lock in qat_alg_backlog_req() is
taken and the backlog queue is being emptied, then there is no request
in the HW queues that can trigger a subsequent interrupt that can clear
the backlog queue. In addition subsequent requests are enqueued to the
backlog list and not sent to the hardware.
Fix it by holding the lock while taking the decision if the request
needs to be included in the backlog queue or not. This synchronizes the
flow with the interrupt handler that drains the backlog queue.
For performance reasons, the logic has been changed to try to enqueue
first without holding the lock.
Fixes: 386823839732 ("crypto: qat - add backlog mechanism")
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Closes: https://lore.kernel.org/all/af9581e2-58f9-cc19-428f-6f18f1f83d54@redhat.com/T/
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The file adf_cfg_services.h cannot be included in header files since it
instantiates the structure adf_cfg_services. Move that structure to its
own file and export the symbol.
This does not introduce any functional change.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add the attribute `num_rps` to the `qat` attribute group. This returns
the number of ring pairs that a single device has. This allows to know
the maximum value that can be set to the attribute `rp2svc`.
Signed-off-by: Ciunas Bennett <ciunas.bennett@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add the attribute `rp2svc` to the `qat` attribute group. This provides a
way for a user to query a specific ring pair for the type of service
that is currently configured for.
When read, the service will be returned for the defined ring pair.
When written to this value will be stored as the ring pair to return
the service of.
Signed-off-by: Ciunas Bennett <ciunas.bennett@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add an interface for the rate limiting feature which allows to add,
remove and modify a QAT SLA (Service Level Agreement).
This adds a new sysfs attribute group, `qat_rl`, which can be accessed
from /sys/bus/pci/devices/<BUS:DEV:FUNCTION> with the following
hierarchy:
|-+ qat_rl
|---- id (RW) # SLA identifier
|---- cir (RW) # Committed Information Rate
|---- pir (RW) # Peak Information Rate
|---- srv (RW) # Service to be rate limited
|---- rp (RW) (HEX) # Ring pairs to be rate limited
|---- cap_rem (RW) # Remaining capability for a service
|---- sla_op (WO) # Allows to perform an operation on an SLA
The API works by setting the appropriate RW attributes and then
issuing a command through the `sla_op`. For example, to create an SLA, a
user needs to input the necessary data into the attributes cir, pir, srv
and rp and then write into `sla_op` the command `add` to execute the
operation.
The API also provides `cap_rem` attribute to get information about
the remaining device capability within a certain service which is
required when setting an SLA.
Signed-off-by: Ciunas Bennett <ciunas.bennett@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The Rate Limiting (RL) feature allows to control the rate of requests
that can be submitted on a ring pair (RP). This allows sharing a QAT
device among multiple users while ensuring a guaranteed throughput.
The driver provides a mechanism that allows users to set policies, that
are programmed to the device. The device is then enforcing those policies.
Configuration of RL is accomplished through entities called SLAs
(Service Level Agreement). Each SLA object gets a unique identifier
and defines the limitations for a single service across up to four
ring pairs (RPs count allocated to a single VF).
The rate is determined using two fields:
* CIR (Committed Information Rate), i.e., the guaranteed rate.
* PIR (Peak Information Rate), i.e., the maximum rate achievable
when the device has available resources.
The rate values are expressed in permille scale i.e. 0-1000.
Ring pair selection is achieved by providing a 64-bit mask, where
each bit corresponds to one of the ring pairs.
This adds an interface and logic that allow to add, update, retrieve
and remove an SLA.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The QAT firmware provides a mechanism to retrieve its capabilities
through the init admin interface.
Add logic to retrieve the firmware capability mask from the firmware
through the init/admin channel. This mask reports if the
power management, telemetry and rate limiting features are supported.
The fw capabilities are stored in the accel_dev structure and are used
to detect if a certain feature is supported by the firmware loaded
in the device.
This is supported only by devices which have an admin AE.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Some enums use the macro BIT. Include bits.h as it is missing.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The admin API is growing and deserves its own include.
Move it from adf_common_drv.h to adf_admin.h.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The 4xxx drivers hardcode the ring to service mapping. However, when
additional configurations where added to the driver, the mappings were
not updated. This implies that an incorrect mapping might be reported
through pfvf for certain configurations.
Add an algorithm that computes the correct ring to service mapping based
on the firmware loaded on the device.
Fixes: 0cec19c761e5 ("crypto: qat - add support for compression for 4xxx")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The adf_fw_config structures hardcode a bit mask that represents the
acceleration engines (AEs) where a certain firmware image will have to
be loaded to. Remove the hardcoded masks and replace them with defines.
This does not introduce any functional change.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The logic that selects the correct adf_fw_config structure based on the
configured service is replicated twice in the uof_get_name() and
uof_get_ae_mask() functions. Refactor the code so that there is no
replication.
This does not introduce any functional change.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add logic to count correctable, non fatal and fatal error for QAT GEN4
devices.
These counters are reported through sysfs attributes in the group
qat_ras.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Introduce ras counters interface for counting QAT specific device
errors and expose them through the newly created qat_ras sysfs
group attribute.
This adds the following attributes:
- errors_correctable: number of correctable errors
- errors_nonfatal: number of uncorrectable non fatal errors
- errors_fatal: number of uncorrectable fatal errors
- reset_error_counters: resets all counters
These counters are initialized during device bring up and cleared
during device shutdown and are applicable only to QAT GEN4 devices.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add logic to detect, report and handle uncorrectable errors reported
through the ERRSOU3 register in QAT GEN4 devices.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add the function adf_get_aram_base() which allows to return the
base address of the aram bar.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add logic to detect, report and handle correctable and uncorrectable
errors related to the compression hardware.
These are detected through the EXPRPSSMXLT, EXPRPSSMCPR and EXPRPSSMDCPR
registers.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add logic to detect, report and handle uncorrectable errors reported
through the ERRSOU2 register in QAT GEN4 devices.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add logic to detect and report uncorrectable errors reported through
the ERRSOU1 register in QAT GEN4 devices.
This also introduces the adf_dev_err_mask structure as part of
adf_hw_device_data which will allow to provide different error masks
per device generation.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add logic to detect and report correctable errors in QAT GEN4
devices.
This includes (1) enabling, disabling and handling error reported
through the ERRSOU0 register and (2) logic to log the errors
in the system log.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add infrastructure for enabling, disabling and reporting errors in the QAT
driver. This adds a new structure, adf_ras_ops, to adf_hw_device_data that
contains the following methods:
- enable_ras_errors(): allows to enable RAS errors at device
initialization.
- disable_ras_errors(): allows to disable RAS errors at device shutdown.
- handle_interrupt(): allows to detect if there is an error and report if
a reset is required. This is executed immediately after the error is
reported, in the context of an ISR.
An initial, empty, implementation of the methods above is provided
for QAT GEN4.
Signed-off-by: Shashank Gupta <shashank.gupta@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Tero Kristo <tero.kristo@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
There is no need to free the reset_data structure if the recovery is
unsuccessful and the reset is synchronous. The function
adf_dev_aer_schedule_reset() handles the cleanup properly. Only
asynchronous resets require such structure to be freed inside the reset
worker.
Fixes: d8cba25d2c68 ("crypto: qat - Intel(R) QAT driver framework")
Signed-off-by: Svyatoslav Pankratov <svyatoslav.pankratov@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The Compress and Verify (CnV) feature check and ensures data integrity
in the compression operation. The implementation of CnV keeps a record
of the CnV errors that have occurred since the driver was loaded.
Expose CnV error stats by providing the "cnv_errors" file under
debugfs. This includes the number of errors detected up to now and
the type of the last error. The error count is provided on a per
Acceleration Engine basis and it is reset every time the driver is loaded.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
QAT devices implement a mechanism that allows them to go autonomously
to a low power state depending on the load.
Expose power management info by providing the "pm_status" file under
debugfs. This includes PM state, PM event log, PM event counters, PM HW
CSRs, per-resource type constrain counters and per-domain power gating
status specific to the QAT device.
This information is retrieved from (1) the FW by means of
ICP_QAT_FW_PM_INFO command, (2) CSRs and (3) counters collected by the
device driver.
In addition, add logic to keep track and report power management event
interrupts and acks/nacks sent to FW to allow/prevent state transitions.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Include kernel.h for GENMASK(), kstrtobool() and types.
Add forward declaration for struct adf_accel_dev. Remove unneeded
include.
This change doesn't introduce any function change.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Create CRYPTO_QAT namespace for symbols exported by the qat_common
module and import those in the QAT drivers. It will reduce the global
namespace crowdedness and potential misuse or the API.
This does not introduce any functional change.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove the implementation of zlib-deflate because it is completely
unused in the kernel.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct adf_fw_counters.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Tom Rix <trix@redhat.com>
Cc: Adam Guerin <adam.guerin@intel.com>
Cc: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: qat-linux@intel.com
Cc: linux-crypto@vger.kernel.org
Cc: llvm@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Increase the size of the buffers used for composing the names used for
the transport debugfs entries and the vector name to avoid a potential
truncation.
This resolves the following errors when compiling the driver with W=1
and KCFLAGS=-Werror on GCC 12.3.1:
drivers/crypto/intel/qat/qat_common/adf_transport_debug.c: In function ‘adf_ring_debugfs_add’:
drivers/crypto/intel/qat/qat_common/adf_transport_debug.c:100:60: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
drivers/crypto/intel/qat/qat_common/adf_isr.c: In function ‘adf_isr_resource_alloc’:
drivers/crypto/intel/qat/qat_common/adf_isr.c:197:47: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size between 0 and 5 [-Werror=format-truncation=]
Fixes: a672a9dc872e ("crypto: qat - Intel(R) QAT transport code")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
QAT GEN4 devices support chained compression operations. These
allow, with a single request to firmware, to hash then compress
data.
Extend the configuration to enable such mode. The cfg_services
operations in sysfs are extended to allow the string "dcc". When
selected, the driver downloads to the device both the symmetric
crypto and the compression firmware images and sends an admin message
to firmware which enables `chained` operations.
In addition, it sets the device's capabilities as the combination
of compression and symmetric crypto capabilities, while excluding
the ICP_ACCEL_CAPABILITIES_CRYPTO_SYMMETRIC bit to indicate
that in this mode, symmetric crypto instances are not supported.
When "dcc" is enabled, the device will handle compression requests
as if the "dc" configuration is loaded ("dcc" is a variation of "dc")
and the driver will register the acomp algorithms.
As for the other extended configurations, "dcc" is only available for
qat_4xxx devices and the chaining service will be only accessible from
user space.
Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The data structure that associates a service id with its name is
replicated across the driver.
Remove duplication by moving this data structure to a new include file,
adf_cfg_services.h in order to have consistency across the drivers.
Note that the data structure is re-instantiated every time the new
include is added to a compilation unit.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The function adf_dev_init(), through the subsystem qat_compression,
populates the list of list of compression instances
accel_dev->compression_list. If the list of instances is not empty,
the function adf_dev_start() will then call qat_compression_registers()
register the compression algorithms into the crypto framework.
If any of the functions in adf_dev_start() fail, the caller of such
function, in the error path calls adf_dev_down() which in turn call
adf_dev_stop() and adf_dev_shutdown(), see for example the function
state_store in adf_sriov.c.
However, if the registration of compression algorithms is not done,
adf_dev_stop() will try to unregister the algorithms regardless.
This might cause the counter active_devs in qat_compression.c to get
to a negative value.
Add a new state, ADF_STATUS_COMPRESSION_ALGS_REGISTERED, which tracks
if the compression algorithms are registered into the crypto framework.
Then use this to unregister the algorithms if such flag is set. This
ensures that the compression algorithms are only unregistered if
previously registered.
Fixes: 1198ae56c9a5 ("crypto: qat - expose deflate through acomp api for QAT GEN2")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The function adf_dev_init(), through the subsystem qat_crypto, populates
the list of list of crypto instances accel_dev->crypto_list.
If the list of instances is not empty, the function adf_dev_start() will
then call qat_algs_registers() and qat_asym_algs_register() to register
the crypto algorithms into the crypto framework.
If any of the functions in adf_dev_start() fail, the caller of such
function, in the error path calls adf_dev_down() which in turn call
adf_dev_stop() and adf_dev_shutdown(), see for example the function
state_store in adf_sriov.c.
However, if the registration of crypto algorithms is not done,
adf_dev_stop() will try to unregister the algorithms regardless.
This might cause the counter active_devs in qat_algs.c and
qat_asym_algs.c to get to a negative value.
Add a new state, ADF_STATUS_CRYPTO_ALGS_REGISTERED, which tracks if the
crypto algorithms are registered into the crypto framework. Then use
this to unregister the algorithms if such flag is set. This ensures that
the crypto algorithms are only unregistered if previously registered.
Fixes: d8cba25d2c68 ("crypto: qat - Intel(R) QAT driver framework")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If the device is already in the up state, a subsequent write of `up` to
the sysfs attribute /sys/bus/pci/devices/<BDF>/qat/state brings the
device down.
Fix this behaviour by ignoring subsequent `up` commands if the device is
already in the up state.
Fixes: 1bdc85550a2b ("crypto: qat - fix concurrency issue when device state changes")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Do not shadow the return code from adf_dev_down() in the error path of
the DEV_DOWN command.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commit 1bdc85550a2b ("crypto: qat - fix concurrency issue when device
state changes") introduced the function adf_dev_down() which wraps the
functions adf_dev_stop() and adf_dev_shutdown().
In a subsequent change, the sequence adf_dev_stop() followed by
adf_dev_shutdown() was then replaced across the driver with just a call
to the function adf_dev_down().
The functions adf_dev_stop() and adf_dev_shutdown() are called in error
paths to stop the accelerator and free up resources and can be called
even if the counterparts adf_dev_init() and adf_dev_start() did not
complete successfully.
However, the implementation of adf_dev_down() prevents the stop/shutdown
sequence if the device is found already down.
For example, if adf_dev_init() fails, the device status is not set as
started and therefore a call to adf_dev_down() won't be calling
adf_dev_shutdown() to undo what adf_dev_init() did.
Do not check if a device is started in adf_dev_down() but do the
equivalent check in adf_sysfs.c when handling a DEV_DOWN command from
the user.
Fixes: 2b60f79c7b81 ("crypto: qat - replace state machine calls")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
