| Age | Commit message (Collapse) | Author |
|---|
|
commit 94cff94634e506a4a44684bee1875d2dbf782722 upstream.
On x86 during boot, clockevent_i8253_disable() can be invoked via
x86_late_time_init -> hpet_time_init() -> pit_timer_init() which happens
with enabled interrupts.
If some of the old i8253 hardware is actually used then lockdep will notice
that i8253_lock is used in hard interrupt context. This causes lockdep to
complain because it observed the lock being acquired with interrupts
enabled and in hard interrupt context.
Make clockevent_i8253_disable() acquire the lock with
raw_spinlock_irqsave() to cure this.
[ tglx: Massage change log and use guard() ]
Fixes: c8c4076723dac ("x86/timer: Skip PIT initialization on modern chipsets")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250404133116.p-XRWJXf@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 531b2ca0a940ac9db03f246c8b77c4201de72b00 upstream.
According to the data sheet, writing the MODE register should stop the
counter (and thus the interrupts). This appears to work on real hardware,
at least modern Intel and AMD systems. It should also work on Hyper-V.
However, on some buggy virtual machines the mode change doesn't have any
effect until the counter is subsequently loaded (or perhaps when the IRQ
next fires).
So, set MODE 0 and then load the counter, to ensure that those buggy VMs
do the right thing and the interrupts stop. And then write MODE 0 *again*
to stop the counter on compliant implementations too.
Apparently, Hyper-V keeps firing the IRQ *repeatedly* even in mode zero
when it should only happen once, but the second MODE write stops that too.
Userspace test program (mostly written by tglx):
=====
#include <stdio.h>
#include <unistd.h>
#include <stdlib.h>
#include <stdint.h>
#include <sys/io.h>
static __always_inline void __out##bwl(type value, uint16_t port) \
{ \
asm volatile("out" #bwl " %" #bw "0, %w1" \
: : "a"(value), "Nd"(port)); \
} \
\
static __always_inline type __in##bwl(uint16_t port) \
{ \
type value; \
asm volatile("in" #bwl " %w1, %" #bw "0" \
: "=a"(value) : "Nd"(port)); \
return value; \
}
BUILDIO(b, b, uint8_t)
#define inb __inb
#define outb __outb
#define PIT_MODE 0x43
#define PIT_CH0 0x40
#define PIT_CH2 0x42
static int is8254;
static void dump_pit(void)
{
if (is8254) {
// Latch and output counter and status
outb(0xC2, PIT_MODE);
printf("%02x %02x %02x\n", inb(PIT_CH0), inb(PIT_CH0), inb(PIT_CH0));
} else {
// Latch and output counter
outb(0x0, PIT_MODE);
printf("%02x %02x\n", inb(PIT_CH0), inb(PIT_CH0));
}
}
int main(int argc, char* argv[])
{
int nr_counts = 2;
if (argc > 1)
nr_counts = atoi(argv[1]);
if (argc > 2)
is8254 = 1;
if (ioperm(0x40, 4, 1) != 0)
return 1;
dump_pit();
printf("Set oneshot\n");
outb(0x38, PIT_MODE);
outb(0x00, PIT_CH0);
outb(0x0F, PIT_CH0);
dump_pit();
usleep(1000);
dump_pit();
printf("Set periodic\n");
outb(0x34, PIT_MODE);
outb(0x00, PIT_CH0);
outb(0x0F, PIT_CH0);
dump_pit();
usleep(1000);
dump_pit();
dump_pit();
usleep(100000);
dump_pit();
usleep(100000);
dump_pit();
printf("Set stop (%d counter writes)\n", nr_counts);
outb(0x30, PIT_MODE);
while (nr_counts--)
outb(0xFF, PIT_CH0);
dump_pit();
usleep(100000);
dump_pit();
usleep(100000);
dump_pit();
printf("Set MODE 0\n");
outb(0x30, PIT_MODE);
dump_pit();
usleep(100000);
dump_pit();
usleep(100000);
dump_pit();
return 0;
}
=====
Suggested-by: Sean Christopherson <seanjc@google.com>
Co-developed-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhkelley@outlook.com>
Link: https://lore.kernel.org/all/20240802135555.564941-2-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 70e6b7d9ae3c63df90a7bba7700e8d5c300c3c60 upstream.
Leaving the PIT interrupt running can cause noticeable steal time for
virtual guests. The VMM generally has a timer which toggles the IRQ input
to the PIC and I/O APIC, which takes CPU time away from the guest. Even
on real hardware, running the counter may use power needlessly (albeit
not much).
Make sure it's turned off if it isn't going to be used.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhkelley@outlook.com>
Link: https://lore.kernel.org/all/20240802135555.564941-1-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ca140a0dc0a18acd4653b56db211fec9b2339986 ]
Add the missing iounmap() when clock frequency fails to get read by the
of_property_read_u32() call, or if the call to msm_timer_init() fails.
Fixes: 6e3321631ac2 ("ARM: msm: Add DT support to msm_timer")
Signed-off-by: Ankit Agrawal <agrawal.ag.ankit@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240713095713.GA430091@bnew-VirtualBox
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 471ef0b5a8aaca4296108e756b970acfc499ede4 upstream.
GCC's named address space checks errors out with:
drivers/clocksource/timer-of.c: In function ‘timer_of_irq_exit’:
drivers/clocksource/timer-of.c:29:46: error: passing argument 2 of
‘free_percpu_irq’ from pointer to non-enclosed address space
29 | free_percpu_irq(of_irq->irq, clkevt);
| ^~~~~~
In file included from drivers/clocksource/timer-of.c:8:
./include/linux/interrupt.h:201:43: note: expected ‘__seg_gs void *’
but argument is of type ‘struct clock_event_device *’
201 | extern void free_percpu_irq(unsigned int, void __percpu *);
| ^~~~~~~~~~~~~~~
drivers/clocksource/timer-of.c: In function ‘timer_of_irq_init’:
drivers/clocksource/timer-of.c:74:51: error: passing argument 4 of
‘request_percpu_irq’ from pointer to non-enclosed address space
74 | np->full_name, clkevt) :
| ^~~~~~
./include/linux/interrupt.h:190:56: note: expected ‘__seg_gs void *’
but argument is of type ‘struct clock_event_device *’
190 | const char *devname, void __percpu *percpu_dev_id)
Sparse warns about:
timer-of.c:29:46: warning: incorrect type in argument 2 (different address spaces)
timer-of.c:29:46: expected void [noderef] __percpu *
timer-of.c:29:46: got struct clock_event_device *clkevt
timer-of.c:74:51: warning: incorrect type in argument 4 (different address spaces)
timer-of.c:74:51: expected void [noderef] __percpu *percpu_dev_id
timer-of.c:74:51: got struct clock_event_device *clkevt
It appears the code is incorrect as reported by Uros Bizjak:
"The referred code is questionable as it tries to reuse
the clkevent pointer once as percpu pointer and once as generic
pointer, which should be avoided."
This change removes the percpu related code as no drivers is using it.
[Daniel: Fixed the description]
Fixes: dc11bae785295 ("clocksource/drivers: Add timer-of common init routine")
Reported-by: Uros Bizjak <ubizjak@gmail.com>
Tested-by: Uros Bizjak <ubizjak@gmail.com>
Link: https://lore.kernel.org/r/20240819100335.2394751-1-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d5c2f8e75a55cfb11a85086c71996af0354a1fb upstream.
The value written into the TPM CnV can only be updated into the hardware
when the counter increases. Additional writes to the CnV write buffer are
ignored until the register has been updated. Therefore, we need to check
if the CnV has been updated before continuing. This may require waiting for
1 counter cycle in the worst case.
Cc: stable@vger.kernel.org
Fixes: 059ab7b82eec ("clocksource/drivers/imx-tpm: Add imx tpm timer support")
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240725193355.1436005-2-Frank.Li@nxp.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5b8843fcd49827813da80c0f590a17ae4ce93c5d upstream.
In tpm_set_next_event(delta), return -ETIME by wrong cast to int when delta
is larger than INT_MAX.
For example:
tpm_set_next_event(delta = 0xffff_fffe)
{
...
next = tpm_read_counter(); // assume next is 0x10
next += delta; // next will 0xffff_fffe + 0x10 = 0x1_0000_000e
now = tpm_read_counter(); // now is 0x10
...
return (int)(next - now) <= 0 ? -ETIME : 0;
^^^^^^^^^^
0x1_0000_000e - 0x10 = 0xffff_fffe, which is -2 when
cast to int. So return -ETIME.
}
To fix this, introduce a 'prev' variable and check if 'now - prev' is
larger than delta.
Cc: stable@vger.kernel.org
Fixes: 059ab7b82eec ("clocksource/drivers/imx-tpm: Add imx tpm timer support")
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240725193355.1436005-1-Frank.Li@nxp.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit db19d3aa77612983a02bd223b3f273f896b243cf ]
There is a race condition in the CMT interrupt handler. In the interrupt
handler the driver sets a driver private flag, FLAG_IRQCONTEXT. This
flag is used to indicate any call to set_next_event() should not be
directly propagated to the device, but instead cached. This is done as
the interrupt handler itself reprograms the device when needed before it
completes and this avoids this operation to take place twice.
It is unclear why this design was chosen, my suspicion is to allow the
struct clock_event_device.event_handler callback, which is called while
the FLAG_IRQCONTEXT is set, can update the next event without having to
write to the device twice.
Unfortunately there is a race between when the FLAG_IRQCONTEXT flag is
set and later cleared where the interrupt handler have already started to
write the next event to the device. If set_next_event() is called in
this window the value is only cached in the driver but not written. This
leads to the board to misbehave, or worse lockup and produce a splat.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 0-...!: (0 ticks this GP) idle=f5e0/0/0x0 softirq=519/519 fqs=0 (false positive?)
rcu: (detected by 1, t=6502 jiffies, g=-595, q=77 ncpus=2)
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.10.0-rc5-arm64-renesas-00019-g74a6f86eaf1c-dirty #20
Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : tick_check_broadcast_expired+0xc/0x40
lr : cpu_idle_poll.isra.0+0x8c/0x168
sp : ffff800081c63d70
x29: ffff800081c63d70 x28: 00000000580000c8 x27: 00000000bfee5610
x26: 0000000000000027 x25: 0000000000000000 x24: 0000000000000000
x23: ffff00007fbb9100 x22: ffff8000818f1008 x21: ffff8000800ef07c
x20: ffff800081c79ec0 x19: ffff800081c70c28 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffc2c717d8
x14: 0000000000000000 x13: ffff000009c18080 x12: ffff8000825f7fc0
x11: 0000000000000000 x10: ffff8000818f3cd4 x9 : 0000000000000028
x8 : ffff800081c79ec0 x7 : ffff800081c73000 x6 : 0000000000000000
x5 : 0000000000000000 x4 : ffff7ffffe286000 x3 : 0000000000000000
x2 : ffff7ffffe286000 x1 : ffff800082972900 x0 : ffff8000818f1008
Call trace:
tick_check_broadcast_expired+0xc/0x40
do_idle+0x9c/0x280
cpu_startup_entry+0x34/0x40
kernel_init+0x0/0x11c
do_one_initcall+0x0/0x260
__primary_switched+0x80/0x88
rcu: rcu_preempt kthread timer wakeup didn't happen for 6501 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402
rcu: Possible timer handling issue on cpu=0 timer-softirq=262
rcu: rcu_preempt kthread starved for 6502 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:I stack:0 pid:15 tgid:15 ppid:2 flags:0x00000008
Call trace:
__switch_to+0xbc/0x100
__schedule+0x358/0xbe0
schedule+0x48/0x148
schedule_timeout+0xc4/0x138
rcu_gp_fqs_loop+0x12c/0x764
rcu_gp_kthread+0x208/0x298
kthread+0x10c/0x110
ret_from_fork+0x10/0x20
The design have been part of the driver since it was first merged in
early 2009. It becomes increasingly harder to trigger the issue the
older kernel version one tries. It only takes a few boots on v6.10-rc5,
while hundreds of boots are needed to trigger it on v5.10.
Close the race condition by using the CMT channel lock for the two
competing sections. The channel lock was added to the driver after its
initial design.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20240702190230.3825292-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6d3bc4c02d59996d1d3180d8ed409a9d7d5900e0 ]
On SAM9 hardware two cascaded 16 bit timers are used to form a 32 bit
high resolution timer that is used as scheduler clock when the kernel
has been configured that way (CONFIG_ATMEL_CLOCKSOURCE_TCB).
The driver initially triggers a reset-to-zero of the two timers but this
reset is only performed on the next rising clock. For the first timer
this is ok - it will be in the next 60ns (16MHz clock). For the chained
second timer this will only happen after the first timer overflows, i.e.
after 2^16 clocks (~4ms with a 16MHz clock). So with other words the
scheduler clock resets to 0 after the first 2^16 clock cycles.
It looks like that the scheduler does not like this and behaves wrongly
over its lifetime, e.g. some tasks are scheduled with a long delay. Why
that is and if there are additional requirements for this behaviour has
not been further analysed.
There is a simple fix for resetting the second timer as well when the
first timer is reset and this is to set the ATMEL_TC_ASWTRG_SET bit in
the Channel Mode register (CMR) of the first timer. This will also rise
the TIOA line (clock input of the second timer) when a software trigger
respective SYNC is issued.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231007161803.31342-1-rwahl@gmx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8051a993ce222a5158bccc6ac22ace9253dd71cb ]
Fix coverity Issue CID 250382: Resource leak (RESOURCE_LEAK).
Add kfree when error return.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231009083922.1942971-1-ping.bai@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8b5bf64c89c7100c921bd807ba39b2eb003061ab ]
Smatch reports:
drivers/clocksource/timer-cadence-ttc.c:529 ttc_timer_probe()
warn: 'timer_baseaddr' from of_iomap() not released on lines: 498,508,516.
timer_baseaddr may have the problem of not being released after use,
I replaced it with the devm_of_iomap() function and added the clk_put()
function to cleanup the "clk_ce" and "clk_cs".
Fixes: e932900a3279 ("arm: zynq: Use standard timer binding")
Fixes: 70504f311d4b ("clocksource/drivers/cadence_ttc: Convert init function to return error")
Signed-off-by: Feng Mingxi <m202271825@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230425065611.702917-1-m202271825@hust.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f5ac896b6a23eb46681cdbef440c1d991b04e519 ]
Currently TTC driver is TIMER_OF_DECLARE type driver. Because of
that, TTC driver may be initialized before other clock drivers. If
TTC driver is dependent on that clock driver then initialization of
TTC driver will failed.
So use TTC driver as platform driver instead of using
TIMER_OF_DECLARE.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1573122988-18399-1-git-send-email-rajan.vaja@xilinx.com
Stable-dep-of: 8b5bf64c89c7 ("clocksource/drivers/cadence-ttc: Fix memory leak in ttc_timer_probe")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
init fails
[ Upstream commit fb73556386e074e9bee9fa2d253aeaefe4e063e0 ]
Smatch reports:
drivers/clocksource/timer-davinci.c:332 davinci_timer_register()
warn: 'base' from ioremap() not released on lines: 274.
Fix this and other potential memory leak problems
by adding a set of corresponding exit lables.
Fixes: 721154f972aa ("clocksource/drivers/davinci: Add support for clockevents")
Signed-off-by: Qinrun Dai <flno@hust.edu.cn>
Link: https://lore.kernel.org/r/20230413135037.1505799-1-flno@hust.edu.cn
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4855f2bd91b6e3461af7d795bfe9a40420122131 ]
There is no need to specify __GFP_NOFAIL when allocating memory here, so
axe it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200409101226.15432-1-christophe.jaillet@wanadoo.fr
Stable-dep-of: fb73556386e0 ("clocksource/drivers/davinci: Fix memory leak in davinci_timer_register when init fails")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bdf8783c0dae9d3d8fc1c4078fe849ab8aa8b583 ]
pr_xxx() functions usually have '\n' at the end of the logging message.
Here, this '\n' is added via the 'pr_fmt' macro.
In order to be more consistent with other files, use a more standard
convention and put these '\n' back in the messages themselves and remove it
from the pr_fmt macro.
While at it, remove a useless message in case of 'kzalloc' failure,
especially with a __GFP_NOFAIL flag.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200409092543.14727-1-christophe.jaillet@wanadoo.fr
Stable-dep-of: fb73556386e0 ("clocksource/drivers/davinci: Fix memory leak in davinci_timer_register when init fails")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2a97d55333e4299f32c98cca6dc5c4db1c5855fc ]
The Renesas Compare Match Timer 0 and 1 (CMT0/1) variants have a
register to control the clock supply to the individual channels.
Currently the driver does not touch this register, and relies on the
documented initial value, which has the clock supply enabled for all
channels present.
However, when Linux starts on the APE6-EVM development board, only the
clock supply to the first CMT1 channel is enabled. Hence the first
channel (used as a clockevent) works, while the second channel (used as
a clocksource) does not. Note that the default system clocksource is
the Cortex-A15 architectured timer, and the user needs to manually
switch to the CMT1 clocksource to trigger the broken behavior.
Fix this by removing the fragile dependency on implicit reset and/or
boot loader state, and by enabling the clock supply explicitly for all
channels used instead. This requires postponing the clk_disable() call,
else the timer's registers cannot be accessed in sh_cmt_setup_channel().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210194648.2901899-1-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d9f15a9de44affe733e34f93bc184945ba277e6d ]
This reverts commit 232ccac1bd9b5bfe73895f527c08623e7fa0752d.
On the subject of suspend, the RISC-V SBI spec states:
This does not cover whether any given events actually reach the hart or
not, just what the hart will do if it receives an event. On PolarFire
SoC, and potentially other SiFive based implementations, events from the
RISC-V timer do reach a hart during suspend. This is not the case for the
implementation on the Allwinner D1 - there timer events are not received
during suspend.
To fix this, the CLOCK_EVT_FEAT_C3STOP (mis)feature was enabled for the
timer driver - but this has broken both RCU stall detection and timers
generally on PolarFire SoC and potentially other SiFive based
implementations.
If an AXI read to the PCIe controller on PolarFire SoC times out, the
system will stall, however, with CLOCK_EVT_FEAT_C3STOP active, the system
just locks up without RCU stalling:
io scheduler mq-deadline registered
io scheduler kyber registered
microchip-pcie 2000000000.pcie: host bridge /soc/pcie@2000000000 ranges:
microchip-pcie 2000000000.pcie: MEM 0x2008000000..0x2087ffffff -> 0x0008000000
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: axi read request error
microchip-pcie 2000000000.pcie: axi read timeout
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
Freeing initrd memory: 7332K
Similarly issues were reported with clock_nanosleep() - with a test app
that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250 & the blamed
commit in place, the sleep times are rounded up to the next jiffy:
== CPU: 1 == == CPU: 2 == == CPU: 3 == == CPU: 4 ==
Mean: 7.974992 Mean: 7.976534 Mean: 7.962591 Mean: 3.952179
Std Dev: 0.154374 Std Dev: 0.156082 Std Dev: 0.171018 Std Dev: 0.076193
Hi: 9.472000 Hi: 10.495000 Hi: 8.864000 Hi: 4.736000
Lo: 6.087000 Lo: 6.380000 Lo: 4.872000 Lo: 3.403000
Samples: 521 Samples: 521 Samples: 521 Samples: 521
Fortunately, the D1 has a second timer, which is "currently used in
preference to the RISC-V/SBI timer driver" so a revert here does not
hurt operation of D1 in its current form.
Ultimately, a DeviceTree property (or node) will be added to encode the
behaviour of the timers, but until then revert the addition of
CLOCK_EVT_FEAT_C3STOP.
Fixes: 232ccac1bd9b ("clocksource/drivers/riscv: Events are stopped during CPU suspend")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/linux-riscv/YzYTNQRxLr7Q9JR0@spud/
Link: https://github.com/riscv-non-isa/riscv-sbi-doc/issues/98/
Link: https://lore.kernel.org/linux-riscv/bf6d3b1f-f703-4a25-833e-972a44a04114@sholland.org/
Link: https://lore.kernel.org/r/20221122121620.3522431-1-conor.dooley@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
ixp4xx_timer_setup is exported, and so can not be an __init function.
But it does not need to be exported as it is only called from one
in-kernel function, so just remove the EXPORT_SYMBOL_GPL() marking to
resolve the build warning.
This is fixed "properly" in commit 41929c9f628b
("clocksource/drivers/ixp4xx: Drop boardfile probe path") but that can
not be backported to older kernels as the reworking of the IXP4xx
codebase is not suitable for stable releases.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 245b993d8f6c4e25f19191edfbd8080b645e12b1 ]
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the only in-tree call-site,
arch/x86/kernel/cpu/mshyperv.c is never compiled as modular.
(CONFIG_HYPERVISOR_GUEST is boolean)
Fixes: dd2cb348613b ("clocksource/drivers: Continue making Hyper-V clocksource ISA agnostic")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220606050238.4162200-1-masahiroy@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a98399cbc1e05f7b977419f03905501d566cf54e ]
When a machine sports more than one SP804 timer instance, we only bring
up the first one, since multiple timers of the same kind are not useful
to Linux. As this is intentional behaviour, we should not return an
error message, as we do today:
===============
[ 0.000800] Failed to initialize '/bus@8000000/motherboard-bus@8000000/iofpga-bus@300000000/timer@120000': -22
===============
Replace the -EINVAL return with a debug message and return 0 instead.
Also we do not reach the init function anymore if the DT node is
disabled (as this is now handled by OF_DECLARE), so remove the explicit
check for that case.
This fixes a long standing bogus error when booting ARM's fastmodels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20220506162522.3675399-1-andre.przywara@arm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9c04a8ff03def4df3f81219ffbe1ec9b44ff5348 ]
The irq_of_parse_and_map() returns 0 on failure, not a negative ERRNO.
Fixes: 89355274e1f7 ("clocksource/drivers/oxnas-rps: Add Oxford Semiconductor RPS Dual Timer")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220422104101.55754-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 232ccac1bd9b5bfe73895f527c08623e7fa0752d ]
Some implementations of the SBI time extension depend on hart-local
state (for example, CSRs) that are lost or hardware that is powered
down when a CPU is suspended. To be safe, the clockevents driver
cannot assume that timer IRQs will be received during CPU suspend.
Fixes: 62b019436814 ("clocksource: new RISC-V SBI timer driver")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20220509012121.40031-1-samuel@sholland.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6a861abceecb68497dd82a324fee45a5332dcece ]
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) environment strings.
The __setup() handler interface isn't meant to handle negative return
values -- they are non-zero, so they mean "handled" (like a return
value of 1 does), but that's just a quirk. So return 1 from
parse_pmtmr(). Also print a warning message if kstrtouint() returns
an error.
Fixes: 6b148507d3d0 ("pmtmr: allow command line override of ioport")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
timer_of_base_init()
[ Upstream commit 4467b8bad2401794fb89a0268c8c8257180bf60f ]
of_base->base can either be iomapped using of_io_request_and_map() or
of_iomap() depending whether or not an of_base->name has been set.
Thus check of_base->base against NULL as of_iomap() does not return a
PTR_ERR() in case of error.
Fixes: 9aea417afa6b ("clocksource/drivers/timer-of: Don't request the resource by name")
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Link: https://lore.kernel.org/r/20220307172656.4836-1-granquet@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eda9a4f7af6ee47e9e131f20e4f8a41a97379293 ]
When building OMAP_DM_TIMER without TIMER_OF, there are orphan sections
due to the use of TIMER_OF_DELCARE() without CONFIG_TIMER_OF. Select
CONFIG_TIMER_OF when enaling OMAP_DM_TIMER:
arm-linux-gnueabi-ld: warning: orphan section `__timer_of_table' from `drivers/clocksource/timer-ti-dm-systimer.o' being placed in section `__timer_of_table'
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202108282255.tkdt4ani-lkp@intel.com/
Cc: Tony Lindgren <tony@atomide.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Fixes: 52762fbd1c47 ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210828175747.3777891-1-keescook@chromium.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
source channel
[ Upstream commit be83c3b6e7b8ff22f72827a613bf6f3aa5afadbb ]
If CMT instance has at least two channels, one channel will be used
as a clock source and another one used as a clock event device.
In that case, IRQ is not requested for clock source channel so
sh_cmt_clock_event_program_verify() might work incorrectly.
Besides, when a channel is only used for clock source, don't need to
re-set the next match_value since it should be maximum timeout as
it still is.
On the other hand, due to no IRQ, total_cycles is not counted up
when reaches compare match time (timer counter resets to zero),
so sh_cmt_clocksource_read() returns unexpected value.
Therefore, use 64-bit clocksoure's mask for 32-bit or 16-bit variants
will also lead to wrong delta calculation. Hence, this mask should
correspond to timer counter width, and above function just returns
the raw value of timer counter register.
Fixes: bfa76bb12f23 ("clocksource: sh_cmt: Request IRQ for clock event device only")
Fixes: 37e7742c55ba ("clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines")
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422123443.73334-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8b33dfe0ba1c84c1aab2456590b38195837f1e6e upstream.
Bad counter reads are experienced sometimes when bit 10 or greater rolls
over. Originally, testing showed that at least 10 lower bits would be
set to the same value during these bad reads. However, some users still
reported time skips.
Wider testing revealed that on some chips, occasionally only the lowest
9 bits would read as the anomalous value. During these reads (which
still happen only when bit 10), bit 9 would read as the correct value.
Reduce the mask by one bit to cover these cases as well.
Cc: stable@vger.kernel.org
Fixes: c950ca8c35ee ("clocksource/drivers/arch_timer: Workaround for Allwinner A64 timer instability")
Reported-by: Roman Stratiienko <r.stratiienko@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210515021439.55316-1-samuel@sholland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7da390694afbaed8e0f05717a541dfaf1077ba51 ]
When DEBUG is defined this error occurs
drivers/clocksource/mxs_timer.c:138:1: error:
expected ‘;’ before ‘}’ token
The preceding statement needs a semicolon.
Replace pr_info() with pr_debug() and remove the unneeded ifdef.
Fixes: eb8703e2ef7c ("clockevents/drivers/mxs: Migrate to new 'set-state' interface")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210118211955.763609-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7a3b8758bd6e45f7b671723b5c9fa2b69d0787ae ]
Compile-testing the ixp4xx timer with CONFIG_OF enabled but
CONFIG_TIMER_OF disabled leads to a harmless warning:
arm-linux-gnueabi-ld: warning: orphan section `__timer_of_table' from `drivers/clocksource/timer-ixp4xx.o' being placed in section `__timer_of_table'
Move the select statement from the platform code into the driver
so it always gets enabled in configurations that rely on it.
Fixes: 40df14cc5cc0 ("clocksource/drivers/ixp4xx: Add OF initialization support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210103135955.3808976-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
CNTKCTL_EL1.EVNTI
[ Upstream commit 8b7770b877d187bfdae1eaf587bd2b792479a31c ]
ARM virtual counter supports event stream, it can only trigger an event
when the trigger bit (the value of CNTKCTL_EL1.EVNTI) of CNTVCT_EL0 changes,
so the actual period of event stream is 2^(cntkctl_evnti + 1). For example,
when the trigger bit is 0, then virtual counter trigger an event for every
two cycles.
While we're at it, rework the way we compute the trigger bit position
by making it more obvious that when bits [n:n-1] are both set (with n
being the most significant bit), we pick bit (n + 1).
Fixes: 037f637767a8 ("drivers: clocksource: add support for ARM architected timer event stream")
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201204073126.6920-3-zhukeqian1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d8cc3905b8073c7cfbff94af889fa8dc71f21dd5 ]
In commit 0ea415390cd3 ("clocksource/arm_arch_timer: Use arch_timer_read_counter
to access stable counters"), we separate stable and normal count reader to omit
unnecessary overhead on systems that have no timer erratum.
However, in erratum_set_next_event_tval_generic(), count reader becomes normal
reader. This converts it to stable reader.
Fixes: 0ea415390cd3 ("clocksource/arm_arch_timer: Use arch_timer_read_counter to access stable counters")
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201204073126.6920-2-zhukeqian1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eee422c46e6840a81c9db18a497b74387a557b29 ]
If clk_notifier_register() failed, ttc_setup_clockevent() will return
without freeing 'ttcce', which will leak memory.
Fixes: 70504f311d4b ("clocksource/drivers/cadence_ttc: Convert init function to return error")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201116135123.2164033-1-yukuai3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c1e6cad00aa2f17845e7270e38ff3cc82c7b022a ]
After calling clk_prepare_enable(), clk_disable_unprepare() need
be called on error path.
Fixes: fbe4b3566ddc ("clocksource/drivers/orion: Convert init function...")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201111064706.3397156-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bc6717d55d07110d8f3c6d31ec2af50c11b07091 ]
When the timer counts to the upper limit, an overflow interrupt is
generated, and the count is reset with the value in the TIME_INI
register. But the software expects to start counting from 0 when
the count overflows, so it forces TIME_INI to 0 to solve the
potential interrupt storm problem.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Tested-by: Xu Kai <xukai@nationalchip.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597735877-71115-1-git-send-email-guoren@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 400d033f5a599120089b5f0c54d14d198499af5a ]
In the init function, if the call to of_iomap() fails, the return
value is ENXIO instead of -ENXIO.
Change to the right negative errno.
Fixes: 691f8f878290f ("clocksource/drivers/h8300_timer8: Convert init function to return error")
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200802111541.5429-1-tianjia.zhang@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
ARM64_WORKAROUND_1418040
commit 4b661d6133c5d3a7c9aca0b4ee5a78c7766eff3f upstream.
ARM64_WORKAROUND_1418040 requires that AArch32 EL0 accesses to
the virtual counter register are trapped and emulated by the kernel.
This makes the vdso pretty pointless, and in some cases livelock
prone.
Provide a workaround entry that limits the vdso to 64bit tasks.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200706163802.1836732-4-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1fbec4ac0d701f350a581941d35643d5a9cd184 upstream.
As we are about to disable the vdso for compat tasks in some circumstances,
let's allow a workaround descriptor to express exactly that.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200706163802.1836732-3-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97884ca8c2925d14c32188e865069f21378b4b4f upstream.
[this is a redesign rather than a backport]
We have a class of errata (grouped under the ARM64_WORKAROUND_1418040
banner) that force the trapping of counter access from 32bit EL0.
We would normally disable the whole vdso for such defect, except that
it would disable it for 64bit userspace as well, which is a shame.
Instead, add a new vdso_clock_mode, which signals that the vdso
isn't usable for compat tasks. This gets checked in the new
vdso_clocksource_ok() helper, now provided for the 32bit vdso.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200706163802.1836732-2-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6d2e16a3181bafb77b535095c39ad1c8b9558c8c ]
Commit 100214889973 ("clocksource: dw_apb_timer_of: use
clocksource_of_init") replaced a publicly available driver
initialization method with one called by the timer_probe() method
available after CLKSRC_OF. In current implementation it traverses
all the timers available in the system and calls their initialization
methods if corresponding devices were either in dtb or in acpi. But
if before the commit any number of available timers would be installed
as clockevent and clocksource devices, after that there would be at most
two. The rest are just ignored since default case branch doesn't do
anything. I don't see a reason of such behaviour, neither the commit
message explains it. Moreover this might be wrong if on some platforms
these timers might be used for different purpose, as virtually CPU-local
clockevent timers and as an independent broadcast timer. So in order
to keep the compatibility with the platforms where the order of the
timers detection has some meaning, lets add the secondly discovered
timer to be of clocksource/sched_clock type, while the very first and
the others would provide the clockevents service.
Fixes: 100214889973 ("clocksource: dw_apb_timer_of: use clocksource_of_init")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200521204818.25436-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cee43dbf2ee3f430434e2b66994eff8a1aeda889 ]
Currently the DW APB Timer driver binds each clockevent timers to a
particular CPU. This isn't good for multiple reasons. First of all seeing
the device is placed on APB bus (which makes it accessible from any CPU
core), accessible over MMIO and having the DYNIRQ flag set we can be sure
that manually binding the timer to any CPU just isn't correct. By doing
so we just set an extra limitation on device usage. This also doesn't
reflect the device actual capability, since by setting the IRQ affinity
we can make it virtually local to any CPU. Secondly imagine if you had a
real CPU-local timer with the same rating and the same CPU-affinity.
In this case if DW APB timer was registered first, then due to the
clockevent framework tick-timer selection procedure we'll end up with the
real CPU-local timer being left unselected for clock-events tracking. But
on most of the platforms (MIPS/ARM/etc) such timers are normally embedded
into the CPU core and are accessible with much better performance then
devices placed on APB. For instance in MIPS architectures there is
r4k-timer, which is CPU-local, assigned with the same rating, and normally
its clockevent device is registered after the platform-specific one.
So in order to fix all of these issues let's make the DW APB Timer CPU
affinity being optional and deactivated by passing a negative CPU id,
which will effectively set the DW APB clockevent timer cpumask to
'cpu_possible_mask'.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200521204818.25436-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0af3e137c144377fbaf5025ba784ff5ba7ad40c9 ]
hyperv_timer.c exports hyperv_cs, which is used by stimers and the
timesync mechanism. However, the clocksource dependency is not
needed: these mechanisms only depend on the partition reference
counter (which can be read via a MSR or via the TSC Reference Page).
Introduce the (function) pointer hv_read_reference_counter, as an
embodiment of the partition reference counter read, and export it
in place of the hyperv_cs pointer. The latter can be removed.
This should clarify that there's no relationship between Hyper-V
stimers & timesync and the Linux clocksource abstractions. No
functional or semantic change.
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200109160650.16150-2-parri.andrea@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cea931c25104e6bddc42eb067f58193f355dbdd7 ]
The DM365 platform has a strange quirk (only present when using ancient
u-boot - mainline u-boot v2013.01 and later works fine) where if we
enable the second half of the timer in periodic mode before we do its
initialization - the time won't start flowing and we can't boot.
When using more recent u-boot, we can enable the timer, then reinitialize
it and all works fine.
To work around this issue only enable clockevents once tim34 is
initialized i.e. move clockevents_config_and_register() below tim34
initialization.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2052d032c06761330bca4944bb7858b00960e868 ]
Currently when setup_irq fails the error exit path will leak the
recently allocated timer structure. Originally the code would
throw a panic but a later commit changed the behaviour to return
via the err_iounmap path and hence we now have a memory leak. Fix
this by adding a err_timer_free error path that kfree's timer.
Addresses-Coverity: ("Resource Leak")
Fixes: 524a7f08983d ("clocksource/drivers/bcm2835_timer: Convert init function to return error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219213246.34437-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9d05c18e8d7de566ff68f221fcae65e78708dd1d upstream.
When enabling ftrace graph tracer, it gets the tracing clock in
ftrace_push_return_trace(). Eventually, it invokes riscv_sched_clock()
to get the clock value. If riscv_sched_clock() isn't marked with
'notrace', it will call ftrace_push_return_trace() and cause infinite
loop.
The result of failure as follow:
command: echo function_graph >current_tracer
[ 46.176787] Unable to handle kernel paging request at virtual address ffffffe04fb38c48
[ 46.177309] Oops [#1]
[ 46.177478] Modules linked in:
[ 46.177770] CPU: 0 PID: 256 Comm: $d Not tainted 5.5.0-rc1 #47
[ 46.177981] epc: ffffffe00035e59a ra : ffffffe00035e57e sp : ffffffe03a7569b0
[ 46.178216] gp : ffffffe000d29b90 tp : ffffffe03a756180 t0 : ffffffe03a756968
[ 46.178430] t1 : ffffffe00087f408 t2 : ffffffe03a7569a0 s0 : ffffffe03a7569f0
[ 46.178643] s1 : ffffffe00087f408 a0 : 0000000ac054cda4 a1 : 000000000087f411
[ 46.178856] a2 : 0000000ac054cda4 a3 : 0000000000373ca0 a4 : ffffffe04fb38c48
[ 46.179099] a5 : 00000000153e22a8 a6 : 00000000005522ff a7 : 0000000000000005
[ 46.179338] s2 : ffffffe03a756a90 s3 : ffffffe00032811c s4 : ffffffe03a756a58
[ 46.179570] s5 : ffffffe000d29fe0 s6 : 0000000000000001 s7 : 0000000000000003
[ 46.179809] s8 : 0000000000000003 s9 : 0000000000000002 s10: 0000000000000004
[ 46.180053] s11: 0000000000000000 t3 : 0000003fc815749c t4 : 00000000000efc90
[ 46.180293] t5 : ffffffe000d29658 t6 : 0000000000040000
[ 46.180482] status: 0000000000000100 badaddr: ffffffe04fb38c48 cause: 000000000000000f
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
[paul.walmsley@sifive.com: cleaned up patch description]
Fixes: 92e0d143fdef ("clocksource/drivers/riscv_timer: Provide the sched_clock")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4411464d6f8b5e5759637235a6f2b2a85c2be0f1 ]
If a hardware-specific driver does not provide a name, the timer-of core
falls back to device_node.name. Due to generic DT node naming policies,
that name is almost always "timer", and thus doesn't identify the actual
timer used.
Fix this by using device_node.full_name instead, which includes the unit
addrees.
Example impact on /proc/timer_list:
-Clock Event Device: timer
+Clock Event Device: timer@fcfec400
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016144747.29538-3-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e001f6a4cc73cd06fc7b8c633bc4906c33dd8ad ]
asm9260_timer_init misses a check for of_clk_get.
Add a check for it and print errors like other clocksource drivers.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016124330.22211-1-hslester96@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
https://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clockevent fixes from Daniel Lezcano:
- Fix scary messages in sh_mtu2 by using platform_irq_count() helper
function (Geert Uytterhoeven)
- Fix double free when using timer-of in the mediatek timer driver
(Fabien Parent)
|
|
As platform_get_irq_by_name() now prints an error when the interrupt
does not exist, looping over possibly non-existing interrupts causes the
printing of scary messages like:
sh_mtu2 fcff0000.timer: IRQ tgi1a not found
sh_mtu2 fcff0000.timer: IRQ tgi2a not found
Fix this by using the platform_irq_count() helper, to avoid touching
non-existent interrupts. Limit the returned number of interrupts to the
maximum number of channels currently supported by the driver in a
future-proof way, i.e. using ARRAY_SIZE() instead of a hardcoded number.
Fixes: 7723f4c5ecdb8d83 ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016143003.28561-1-geert+renesas@glider.be
|
|
When timer_of_init fails, it cleans up after itself by undoing
everything it did during the initialization function.
mtk_syst_init and mtk_gpt_init both call timer_of_cleanup if
timer_of_init fails. timer_of_cleanup try to release the resource
taken. Since these resources have already been cleaned up by
timer_of_init, we end up getting a few warnings printed:
[ 0.001935] WARNING: CPU: 0 PID: 0 at __clk_put+0xe8/0x128
[ 0.002650] Modules linked in:
[ 0.003058] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.67+ #1
[ 0.003852] Hardware name: MediaTek MT8183 (DT)
[ 0.004446] pstate: 20400085 (nzCv daIf +PAN -UAO)
[ 0.005073] pc : __clk_put+0xe8/0x128
[ 0.005555] lr : clk_put+0xc/0x14
[ 0.005988] sp : ffffff80090b3ea0
[ 0.006422] x29: ffffff80090b3ea0 x28: 0000000040e20018
[ 0.007121] x27: ffffffc07bfff780 x26: 0000000000000001
[ 0.007819] x25: ffffff80090bda80 x24: ffffff8008ec5828
[ 0.008517] x23: ffffff80090bd000 x22: ffffff8008d8b2e8
[ 0.009216] x21: 0000000000000001 x20: fffffffffffffdfb
[ 0.009914] x19: ffffff8009166180 x18: 00000000002bffa8
[ 0.010612] x17: ffffffc012996980 x16: 0000000000000000
[ 0.011311] x15: ffffffbf004a6800 x14: 3536343038393334
[ 0.012009] x13: 2079726576652073 x12: 7eb9c62c5c38f100
[ 0.012707] x11: ffffff80090b3ba0 x10: ffffff80090b3ba0
[ 0.013405] x9 : 0000000000000004 x8 : 0000000000000040
[ 0.014103] x7 : ffffffc079400270 x6 : 0000000000000000
[ 0.014801] x5 : ffffffc079400248 x4 : 0000000000000000
[ 0.015499] x3 : 0000000000000000 x2 : 0000000000000000
[ 0.016197] x1 : ffffff80091661c0 x0 : fffffffffffffdfb
[ 0.016896] Call trace:
[ 0.017218] __clk_put+0xe8/0x128
[ 0.017654] clk_put+0xc/0x14
[ 0.018048] timer_of_cleanup+0x60/0x7c
[ 0.018551] mtk_syst_init+0x8c/0x9c
[ 0.019020] timer_probe+0x6c/0xe0
[ 0.019469] time_init+0x14/0x44
[ 0.019893] start_kernel+0x2d0/0x46c
[ 0.020378] ---[ end trace 8c1efabea1267649 ]---
[ 0.020982] ------------[ cut here ]------------
[ 0.021586] Trying to vfree() nonexistent vm area ((____ptrval____))
[ 0.022427] WARNING: CPU: 0 PID: 0 at __vunmap+0xd0/0xd8
[ 0.023119] Modules linked in:
[ 0.023524] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.19.67+ #1
[ 0.024498] Hardware name: MediaTek MT8183 (DT)
[ 0.025091] pstate: 60400085 (nZCv daIf +PAN -UAO)
[ 0.025718] pc : __vunmap+0xd0/0xd8
[ 0.026176] lr : __vunmap+0xd0/0xd8
[ 0.026632] sp : ffffff80090b3e90
[ 0.027066] x29: ffffff80090b3e90 x28: 0000000040e20018
[ 0.027764] x27: ffffffc07bfff780 x26: 0000000000000001
[ 0.028462] x25: ffffff80090bda80 x24: ffffff8008ec5828
[ 0.029160] x23: ffffff80090bd000 x22: ffffff8008d8b2e8
[ 0.029858] x21: 0000000000000000 x20: 0000000000000000
[ 0.030556] x19: ffffff800800d000 x18: 00000000002bffa8
[ 0.031254] x17: 0000000000000000 x16: 0000000000000000
[ 0.031952] x15: ffffffbf004a6800 x14: 3536343038393334
[ 0.032651] x13: 2079726576652073 x12: 7eb9c62c5c38f100
[ 0.033349] x11: ffffff80090b3b40 x10: ffffff80090b3b40
[ 0.034047] x9 : 0000000000000005 x8 : 5f5f6c6176727470
[ 0.034745] x7 : 5f5f5f5f28282061 x6 : ffffff80091c86ef
[ 0.035443] x5 : ffffff800852b690 x4 : 0000000000000000
[ 0.036141] x3 : 0000000000000002 x2 : 0000000000000002
[ 0.036839] x1 : 7eb9c62c5c38f100 x0 : 7eb9c62c5c38f100
[ 0.037536] Call trace:
[ 0.037859] __vunmap+0xd0/0xd8
[ 0.038271] vunmap+0x24/0x30
[ 0.038664] __iounmap+0x2c/0x34
[ 0.039088] timer_of_cleanup+0x70/0x7c
[ 0.039591] mtk_syst_init+0x8c/0x9c
[ 0.040060] timer_probe+0x6c/0xe0
[ 0.040507] time_init+0x14/0x44
[ 0.040932] start_kernel+0x2d0/0x46c
This commit remove the calls to timer_of_cleanup when timer_of_init
fails since it is unnecessary and actually cause warnings to be printed.
Fixes: a0858f937960 ("mediatek: Convert the driver to timer-of")
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/linux-arm-kernel/20190919191315.25190-1-fparent@baylibre.com/
|
|
Randy Dunlap reports on the sparse list that sparse warns about this
expression:
of_irq->percpu ? free_percpu_irq(of_irq->irq, clkevt) :
free_irq(of_irq->irq, clkevt);
and honestly, sparse is correct to warn. The return type of
free_percpu_irq() is 'void', while free_irq() returns a 'const void *'
that is the devname argument passed in to the request_irq().
You can't mix a void type with a non-void types in a conditional
expression according to the C standard. It so happens that gcc seems to
accept it - and the resulting type of the expression is void - but
there's really no reason for the kernel to have this kind of
non-standard expression with no real upside.
The natural way to write that expression is with an if-statement:
if (of_irq->percpu)
free_percpu_irq(of_irq->irq, clkevt);
else
free_irq(of_irq->irq, clkevt);
which is more legible anyway.
I'm not sure why that timer-of code seems to have this odd pattern. It
does the same at allocation time, but at least there the types match,
and it makes sense as an expression.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
