summaryrefslogtreecommitdiff
path: root/drivers/clk/rockchip/clk-rk3288.c
AgeCommit message (Collapse)Author
2014-12-31GMAC: modify CRU config for Rockchip RK3288 SoCs integrated GMACRoger Chen
modify CRU config for GMAC driver changes since v2: 1. remove SCLK_MAC_PLL Signed-off-by: Roger Chen <roger.chen@rock-chips.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31clk: rockchip: rk3288: Make s2r reliable by switching PLLs to slow modeDoug Anderson
We've been seeing some crashes at resume time on rk3288-based systems. On some machines they simply never wake up from suspend. Symptoms include: - System clearly got to sleep OK. Power consumption is low, the PWM for the PWM regulator has stopped, and the "global_pwroff" output shows that the system is down. - When system tries to wake up power consumption goes up. - No kernel resume code (which was left in PMU SRAM) ran. We added some basic logging to this code (write to a location in SRAM right at resume time) and didn't see the logging run. It appears that we can fix the problem by slowing down APLL before we suspend. On the system I tested things seemed reliable if I disabled 1.8GHz and 1.7GHz. The Mask ROM itself tries to slow things down (which is why PLLs are in slow mode by the time we get to the kernel), but apparently it is crashing before it even gets there. We'll be super paranoid and not just go down to 1.6GHz but we'll match what the Mask ROM seems to be doing and go into slow mode. We'll also be safe and put all PLLs (not just APLL) into slow mode (well, except DPLL which is needed for SDRAM). We'll even put NPLL into slow mode which the Mask ROM didn't do (not that it's used for much important stuff at early resume time). Note that the old Rockchip reference code did something just like this, though they jammed it into pm.c instead of putting it in the syscore ops of the clock driver. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-12-28clk: rockchip: fix rk3288 cpuclk core dividersHeiko Stuebner
Commit 0e5bdb3f9fa5 (clk: rockchip: switch to using the new cpuclk type for armclk) didn't take into account that the divider used on rk3288 are of the (n+1) type. The rk3066 and rk3188 socs use more complex divider types making it necessary for the list-elements to be the real register-values to write. Therefore reduce divider values in the table accordingly so that they really are the values that should be written to the registers and match the dividers actually specified for the rk3288. Reported-by: Sonny Rao <sonnyrao@chromium.org> Fixes: 0e5bdb3f9fa5 ("clk: rockchip: switch to using the new cpuclk type for armclk") Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Doug Anderson <dianders@chromium.org> Cc: stable@vger.kernel.org
2014-12-21clk: rockchip: Add CLK_SET_RATE_PARENT to sclk_uart clocksDoug Anderson
We'd like to be able to set the clock rate of the sclk_uart clocks and actually be able to achieve clock rates greater than 24MHz. To do this we need to be able to pass rate changes upward. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-11-28clk: rockchip: Add support for the mmc clock phases using the frameworkAlexandru M Stan
This patch adds the 2 physical clocks for the mmc (drive and sample). They're mostly there for the phase properties, but they also show the true clock (by dividing by RK3288_MMC_CLKGEN_DIV). The drive and sample phases are generated by dividing an upstream parent clock by 2, this allows us to adjust the phase by 90 deg. There's also an option to have up to 255 delay elements (40-80 picoseconds long). This driver uses those elements (under the assumption that they're 60 ps long) to generate approximate 22.5 degrees options. 67.5 (22.5*3) might be as high as 90 deg if the delay elements are as big as 80 ps, so a finer division (smaller than 22.5) was not picked because the phase might not be monotonic anymore. Suggested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Alexandru M Stan <amstan@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-11-28clk: rockchip: rk3288 export i2s0_clkout for use in DTSonny Rao
This exposes the clock that comes out of the i2s block which generally goes to the audio codec. Signed-off-by: Sonny Rao <sonnyrao@chromium.org> [removed CLK_SET_RATE_PARENT from original patch] Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-11-26clk: rockchip: use clock ID for DMC (memory controller) on rk3288Jeff Chen
The DMC clocks need to be turned off at runtime. Use the newly assigned clock IDs to export them. Signed-off-by: Jeff Chen <cym@rock-chips.com> [dianders: split into two patches; adjusted commit msg] Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-11-25clk: rockchip: add ROCKCHIP_PLL_SYNC_RATE flag to some pllsHeiko Stuebner
Add the new flag to gpll and cpll on rk3188 and similar and to gpll, cpll and npll on rk3288. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Kever Yang <kever.yang@rock-chips.com>
2014-11-25clk: rockchip: add ability to specify pll-specific flagsHeiko Stuebner
This adds a flag parameter to plls that allows us to create special flags to tweak the behaviour of the plls if necessary. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Kever Yang <kever.yang@rock-chips.com>
2014-11-16clk: rockchip: fix clock select order for rk3288 usbphy480m_srcKever Yang
According to rk3288 trm, the mux selector locate at bit[12:11] of CRU_CLKSEL13_CON shows: 2'b00: select HOST0 USB pll clock (clk_otgphy1) 2'b01: select HOST1 USB pll clock (clk_otgphy2) 2'b10: select OTG USB pll clock (clk_otgphy0) The clock map is in Fig. 3-4 CRU Clock Architecture Diagram 3 - clk_otgphy0 -> USB PHY OTG - clk_otgphy1 -> USB PHY host0 - clk_otgphy2 -> USB PHY host1 Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-11-16clk: rockchip: fix rk3288 clk_usbphy480m_gate bit location in registerKever Yang
According to rk3288 trm, the clk_usbphy480m_gate is located at bit 14 of CRU_CLKGATE5_CON register. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-11-13clk: rockchip: ensure HCLK_VIO2_H2P and PCLK_VIO2_H2P stay enabledDmitry Torokhov
Currently there is no driver owning these clocks and they have to stay up for the system to function properly, so let's mark them as CLK_IGNORE_UNUSED. Without this patch we have trouble with suspend/resume and we have trouble turning the eDP back on if it ever idles off. Signed-off-by: Dmitry Torokhov <dtor@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-11-10clk: rockchip: rk3288: add suspend and resumeChris Zhong
save and restore some clks, which might be changed in suspend. Signed-off-by: Tony Xie <xxx@rock-chips.com> Signed-off-by: Chris Zhong <zyw@rock-chips.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-11-04clk: rockchip: disable unused clocksKever Yang
The rockchip clock driver use CLK_IGNORE_UNUSED flag to make sure all the clocks are available like default power on state. We have implement the clock manage in most of rockchip drivers, it is time to remove it for power save. Instead we add CLK_IGNORE_UNUSED for some clock nodes which should be on during boot or no module driver in kernel will initialize it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-10-29clk: rockchip: change PLL setting for better clock jitterKever Yang
dclk_vop0/1 is the source of HDMI TMDS clock in rk3288, usually we use 594MHz for clock source of dclk_vop0/1. HDMI CTS 7-9 require TMDS Clock jitter is lower than 0.25*Tbit: TMDS clock(MHz) CTS require jitter (ps) 297 84.2 148.5 168 74.25 336 27 1247 PLL BW and VCO frequency effects the jitter of PLL output clock, clock jitter is better if BW is lower or VCO frequency is higher. If PLL use default setting of RK3066_PLL_RATE( 594000000, 2, 198, 4), the TMDS Clock jitter is higher than 250ps, which means we can't pass the test when TMDS clock is 297MHz or 148.5MHz. If we use RK3066_PLL_RATE_BWADJ(594000000, 1, 198, 8, 1), the TMDS Clock jitter is about 60ps and we can pass all test case. So we need this patch to make hdmi si test pass. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-10-20clk: rockchip: add npll to source of sclk_gpuKever Yang
The possible sources for the rk3288-gpu-clock also include the npll, making it the same list of sources as for uart0. This patch make a common source for uart0 pll src and sclk_gpu, so that gpu can get its clock from npll. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-10-20clk: rockchip: rk3288: removing the CLK_SET_RATE_PARENT from i2s_clkoutJianqun
Removing the CLK_SET_RATE_PARENT from i2s_clkout, to limit i2s0_clkout to select between its two parent without being able influence the core i2s clock. Tested on rk3288 board, suggested by Heiko. Signed-off-by: Jianqun <jay.xu@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-10-20clk: rockchip: add 400MHz and 500MHz for rk3288 clock rateKever Yang
This patch add 400MHz and 500MHz to clock rate table for rk3288. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-10-20clk: rockchip: Add CLK_SET_RATE_PARENT to aclk_cpu_preDoug Anderson
We'd like to be able to call clk_set_rate() on aclk_cpu (a gate) at bootup. In order for this to have any effect we need its parent (aclk_cpu_pre) to percolate the rate change to _its_ parent (aclk_cpu_src). Add CLK_SET_RATE_PARENT to make this happen. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-10-20clk: rockchip: fix parent for spdif_8ch_frac on rk3288Sonny Rao
The parent should be spdif_8ch_pre not spdif_8ch_src, which doesn't exist and looks to be a typo. The TRM also confirms this. Signed-off-by: Sonny Rao <sonnyrao@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-10-01clk: rockchip: add restart handlerHeiko Stübner
Add infrastructure to write the correct value to the restart register and register the restart notifier for both rk3188 (including rk3066) and rk3288. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-10-01clk: rockchip: rk3288: i2s_frac adds flag to set parent's rateJianqun
The relation of i2s nodes as follows: i2s_src 0 0 594000000 0 i2s_frac 0 0 11289600 0 i2s_pre 0 0 11289600 0 sclk_i2s0 0 0 11289600 0 i2s0_clkout 0 0 11289600 0 hclk_i2s0 1 1 99000000 0 sclk_i2s0 is the master clock, when to set rate of sclk_i2s0, should allow to set its parent's rate, by add flag CLK_SET_RATE_PARENT for "i2s_frac", "i2s_pre", "i2s0_clkout" and "sclk_i2s0". Tested on rk3288 board using max98090, with command "aplay <music.wav>" Change-Id: I12faad082566532b65a7de8c0a6845e1c17870e6 Signed-off-by: Jianqun <jay.xu@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2014-09-27clk: rockchip: switch to using the new cpuclk type for armclkHeiko Stuebner
This adds the necessary soc-specific divider values and switches the armclk to use the newly introduced cpuclk type. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org>
2014-09-27clk: rockchip: make tightly bound armclk child-clocks read-onlyHeiko Stuebner
Rockchip SoCs contain clocks tightly bound to the armclk, where the best rate / divider is supplied by the vendor after careful measuring. Often this ideal rate may be greater than the current rate. Therefore prevent the ccf from trying to set these dividers itself by setting them to read-only. In the case of the rk3066, this also includes the aclk_cpu, which makes it necessary to also split its direct child-clocks (pclk_cpu, hclk_cpu, ...) into individual definitions for rk3066 and rk3188. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org>
2014-09-27clk: rockchip: fix rk3288 pll status register locationJianqun
In RK3288, APLL lock status bit is in GRF_SOC_STATUS1, but in RK3188, is GRFSOC_STATUS0. Signed-off-by: Jianqun <jay.xu@rock-chips.com> Also name the constant accordingly as GRF_SOC_STATUS1 to prevent confusion. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org>
2014-09-25Merge branch 'clk-next-rockchip' into clk-nextMike Turquette
2014-09-25clk: rockchip: add clock node in PD_VIDEOKever Yang
This patch add the clock node in PD_VIDEO Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Mike Turquette <mturquette@linaro.org>
2014-09-25clk: rockchip: use the clock id for nodes initKever Yang
This patch use the new defined clock ID to initial the clock nodes. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Mike Turquette <mturquette@linaro.org>
2014-09-25clk: rockchip: add missing rk3288 npll rate tableHeiko Stübner
The npll on rk3288 is exactly the same pll type as the other 4. Yet it was missing the link to the rate table, making rate changes impossible. Change that by setting the table. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Doug Anderson <dianders@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org> Tested-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
2014-09-25clk: rockchip: rk3288: fix softreset register countMark yao
The rk3288 actually has 12 softresets, so fix the register count. Signed-off-by: Mark yao <mark.yao@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Mike Turquette <mturquette@linaro.org>
2014-09-17Merge branch 'clk-fixes' into clk-nextMike Turquette
2014-09-10clk: rockchip: also protect hclk_peri as criticalHeiko Stübner
The dwc2 usb controller also uses agressive clock gating, which in this case leads to hclk_peri getting disabled and hanging the system. Therefore move it to the critical clocks until we also control that part of the system. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Mike Turquette <mturquette@linaro.org>
2014-09-03clk: rockchip: Fix the clocks for i2c1 and i2c2Doug Anderson
The clocks for i2c1 and i2c2 are flipped. The clock tree matched the Technical Reference Manual (TRM) but the TRM was wrong. Swap them in the clock tree. This was determined experimentally (by Addy) and confirmed by the Rockchip IC team. Signed-off-by: Doug Anderson <dianders@chromium.org> Reported-by: Addy Ke <addy.ke@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Mike Turquette <mturquette@linaro.org>
2014-09-02clk: rockchip: protect critical clocks from getting disabledHeiko Stübner
The clock-tree contains clocks that should never get disabled automatically. One example are the base ACLKs, the base supplies for all peripherals. Therefore add a structure similar to the sunxi clock-tree to protect these special clocks from being disabled. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Doug Anderson <dianders@chromium.org> Tested-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
2014-07-13clk: rockchip: add clock controller for rk3288Heiko Stübner
Add the clock tree definition for the new rk3288 SoC. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-By: Max Schwarz <max.schwarz@online.de> Tested-By: Max Schwarz <max.schwarz@online.de> Signed-off-by: Mike Turquette <mturquette@linaro.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 15:50:40 +0000