| Age | Commit message (Collapse) | Author |
|---|
|
Similar to an earlier fix for the SAI clocks, the DCU clock hierarchy
mixes the bus clock with the display controllers pixel clock. Tests
have shown that the gates in CCM_CCGR3/9 registers do not control
the DCU pixel clock, but only the register access clock (bus clock).
Fix this by defining the parent clock of VF610_CLK_DCUx to be the bus
clock (ipg_bus).
Since the clock has not been used far, there are no further changes
needed.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the necessary clock to use the ckil on i.MX7.
Inspired from the following patch:
https://github.com/boundarydevices/linux-imx6/commit/b80e8271
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The clock register are lost when enterying LPSTOPx, hence provide
suspend/resume functions restoring them. The clock gates get
restored by the individual driver, hence we do not need to restore
them here.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To use STOP mode without putting DDR3 into self-refresh mode, we
need to keep the DDR clock enabled. Use the new gate configuration
with a value of 2 to make sure that the clock is enabled in RUN,
WAIT and STOP mode.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The 2-bit gates found i.MX and Vybrid SoC support different clock
configuration:
0b00: clk disabled
0b01: clk enabled in RUN mode but disabled in WAIT and STOP mode
0b10: clk enabled in RUN, WAIT and STOP mode (only Vybrid)
0b11: clk enabled in RUN and WAIT mode
For some clocks, we might want to configure different behaviour,
e.g. a memory clock should be on even in STOP mode. Add a new
function imx_clk_gate2_cgr which allow to configure specific
gate values through the cgr_val parameter.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
SAIx and SAIx_IPG share the same bit fields in the CCM registers, so
we should better register them via imx_clk_gate2_shared().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This flag is a no-op now. Remove usage of the flag.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-next
Pull i.MX clk updates from Shawn Guo:
The i.MX clock update for 4.6:
- Add the clock driver support for the latest i.MX6 family SoCs
addition - i.MX6QP.
- Clean up the whitespace in i.MX6UL clock driver and add the missing
KPP clock.
- Correct pwm7 clock name in i.MX6UL clock driver.
* tag 'imx-clk-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx: add kpp clock for i.MX6UL
clk: imx: whitespace cleanup; no functional change
clk: imx: correct pwm7 clock name in driver for i.MX6UL
clk: imx: Add clock support for imx6qp
|
|
Add the necessary clock to use the KPP interface on i.MX6UL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
remove whitespace before TAB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Don't capitalize p in the pwm7 clock name.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
most of the clock tree structures on i.MX6 Quad Plus are
same as on i.MX6Q. there still some differences between
these two SOCs. compared to the i.XM6Q, the differents of
clocks on i.MX6QP is mainly on:
1. New clock gate added to support the PRE and PRG modules
2. 24MHz OSC clock option added to the UART, IPG, ECSPI, and
CAN clock roots.
3. MMDC channel 1 clock gate is now controllable.
4. clock gating added to the LDB_DIx_IPU clocks on i.MX6QP
5. EMI clock root divider fix
6. other updates fo CSCMRx, CSCDRx and CS2CDR registers.
detailed infomation, please refer to the i.MX6QP RM.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
to_clk_*(_hw) macros have been repeatedly defined in many places.
This patch moves all the to_clk_*(_hw) definitions in the common
clock framework to public header clk-provider.h, and drop the local
definitions.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-next
The i.MX clock updates for 4.5:
- Add is_prepared function callback for pllv3 clock driver
- Use imx_check_clocks() on imx6ul and imx7d clock drivers to save
some code
- Add a core clock for imx7d to support generic cpufreq driver
- Support imx6q clock routing with OSC to anaclk2/2b
- To support more precise pixel clocks on imx5, allow ipu_di_sel clock
selectors to influence the PLLs that they are derived from
- A cleanup on imx25 OSC clock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
|
|
To obtain exact pixel clocks, allow the DI clock selectors to influence
the PLLs that they are derived from.
Commit 4591b13289b5 ("ARM: i.MX6: ipu_di_sel clocks can set parent
rates") did this for i.MX6.
Port it to enable high display resolutions on i.MX53 based platforms
such as CX9020 Embedded PC, too.
Signed-off-by: Patrick Brünn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
As we already have a 'imx_check_clocks' to do the clock error
check, so cleanup the error check code.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a virtual arm clk to abstract the actual steps
when changing the ARM core frequency.So we can using
the 'cpufreq-dt' driver on i.MX7D/Solo.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Synchronous Audio Interface (SAI) instances are clocked by
independent clocks: The bus clock and the audio clock (as shown in
Figure 51-1 in the Vybrid Reference Manual). The clock gates in
CCGR0/CCGR1 for SAI0 through SAI3 are bus clock gates, as access
tests to the registers with/without gating those clocks have shown.
The audio clock is gated by the SAIx_EN gates in CCM_CSCDR1,
followed by a clock divider (SAIx_DIV). Currently, the parent of
the bus clock gates has been assigned to SAIx_DIV, which is not
involved in the bus clock path for the SAI instances (see chapter
9.10.12, SAI clocking in the Vybrid Reference Manual).
Fix this by define the parent clock of VF610_CLK_SAIx to be the bus
clock.
If the driver needs the audio clock (when used in master mode), a
fixed device tree is required which assign the audio clock properly
to VF610_CLK_SAIx_DIV.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
OSC can be used as USB hub source clock. An example we can route to
CLK2_P imx6 pin.
This show a usage example:
[...]
usb_hub: usb-hub {
compatible = "smsc,usb3503a";
clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>;
clock-names = "refclk";
};
};
[...]
&clks {
assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
};
/sys/kernel/debug/clk/clk_summary
osc 5 5 24000000 0 0
[...]
lvds2_sel 1 1 24000000 0 0
lvds2_gate 1 1 24000000 0 0
[...]
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add 'is_prepared' callback function for pllv3 type clk to make sure when
the system is bootup, the unused clk is in a known state to match the
prepare count info.
Signed-off-by: Bai Ping <b51503@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The 'osc' clock is already initialized by the fixed clock defined in
imx25.dtsi. The imx25 clock driver tries to add this clock for a second
time and fails with -EEXIST:
i.MX clk 1: register failed with -17
As the clock is already properly setup in DT with a different driver, we
can completely remove the handling in the imx25 clock driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
for_each_compatible_node performs an of_node_get on each iteration, so a
break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e;
@@
for_each_compatible_node(n,...) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
for_each_compatible_node performs an of_node_get on each iteration, so a
break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e;
@@
for_each_compatible_node(n,...) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-next
Pull i.MX updates from Shawn Guo:
"The i.MX clock updates for 4.4:
- A couple of fixes on i.MX31 and i.MX35 clock initialization functions
which makes mxc_timer_init() currently be called twice for DT boot.
- Increase i.MX6UL AXI bus clock rate to 264MHz which is the optimal
design target.
- Add a few missing clocks, ADC clock for i.MX7D, OCOTP clock for
Vybrid, and SPDIF_GCLK for i.MX6.
- A series from Lucas to fix early debug UART clock setup. This is
currently a one-off fix for i.MX platform, and can be extended to
become a generic solution later."
* tag 'imx-clk-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx6: Add SPDIF_GCLK clock in clock tree
clk: imx7d: add ADC root clock
clk: imx31: Do not call mxc_timer_init twice when booting with DT
clk: imx7d: retain early UART clocks during kernel init
clk: imx6: retain early UART clocks during kernel init
clk: imx5: retain early UART clocks during kernel init
clk: imx35: retain early UART clocks during kernel init
clk: imx31: retain early UART clocks during kernel init
clk: imx27: retain early UART clocks during kernel init
clk: imx25: retain early UART clocks during kernel init
clk: imx: add common logic to detect early UART usage
clk: imx35: Do not call mxc_timer_init twice when booting with DT
clk: clk-vf610: Add clock for Vybrid OCOTP controller
clk: imx: increase AXI clock rate to 264MHz for i.MX6UL
|
|
Correct SPDIF clock setting issue in clock tree, the SPDIF_GCLK is also
one clock of SPDIF, which is missed before.
We found an issue that imx can't enter low power mode with spdif
if IMX6x_CLK_SPDIF is used as the core clock of spdif. Because
spdif driver will register IMX6x_CLK_SPDIF clock to regmap, regmap will do
clk_prepare in init function, then IMX6x_CLK_SPDIF clock is prepared in probe,
so its parent clock (PLL clock) is prepared, the prepare operation of
PLL clock is to enable the clock. But I.MX needs all PLL clock is disabled,
then it can enter low power mode.
So we can't use IMX6x_CLK_SPDIF as the core clock of spdif, the correct spdif
core clock is SPDIF_GCLK, which share same gate bit with IMX6x_CLK_SPDIF clock.
SPDIF_GCLK's parent clock is ipg clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add ADC root clock support in imx7d clock tree.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This simplifies the given function by getting rid of the manual
sign extension as well as saving an absolute value in an extra
variable.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
mxc_timer_init must not be called from within mx31_clocks_init_dt. It will
eventually be called by imx31_timer_init_dt
(drivers/clocksource/timer-imx-gpt.c).
This arranges the initialization code similar to clk-imx27.c
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Both earlycon and eralyprintk depend on the bootloader setup UART
clocks being retained. This patch adds the common logic to detect such
situations and make the information available to the clock drivers, as
well as adding the facilities to disable those clocks at the end of
the kernel init.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
mxc_timer_init must not be called from within mx35_clocks_init_dt. It will
eventually be called by imx31_timer_init_dt
(drivers/clocksource/timer-imx-gpt.c).
This arranges the initialization code similar to clk-imx27.c
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add clock support for Vybrid On-Chip One Time Programmable
(OCOTP) controller.
While the OCOTP block does not require explicit clock gating,
for programming the OCOTP timing register the clock rate of
ipg clock is required for timing calculations related to fuse
and shadow register read sequence. We explicitly specify the
ipg clock for OCOTP as a result.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6UL, AXI clock rate's design target is 264MHz, but by default
it is only set to 198MHz which is NOT good enough for performance,
this patch increases AXI clock rate from 198MHz to 264MHz to meet
the design target, this is done by switching its parent clock
"periph" from 396MHz PFD to 528MHz PLL.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.3:
API:
- the AEAD interface transition is now complete.
- add top-level skcipher interface.
Drivers:
- x86-64 acceleration for chacha20/poly1305.
- add sunxi-ss Allwinner Security System crypto accelerator.
- add RSA algorithm to qat driver.
- add SRIOV support to qat driver.
- add LS1021A support to caam.
- add i.MX6 support to caam"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (163 commits)
crypto: algif_aead - fix for multiple operations on AF_ALG sockets
crypto: qat - enable legacy VFs
MPI: Fix mpi_read_buffer
crypto: qat - silence a static checker warning
crypto: vmx - Fixing opcode issue
crypto: caam - Use the preferred style for memory allocations
crypto: caam - Propagate the real error code in caam_probe
crypto: caam - Fix the error handling in caam_probe
crypto: caam - fix writing to JQCR_MS when using service interface
crypto: hash - Add AHASH_REQUEST_ON_STACK
crypto: testmgr - Use new skcipher interface
crypto: skcipher - Add top-level skcipher interface
crypto: cmac - allow usage in FIPS mode
crypto: sahara - Use dmam_alloc_coherent
crypto: caam - Add support for LS1021A
crypto: qat - Don't move data inside output buffer
crypto: vmx - Fixing GHASH Key issue on little endian
crypto: vmx - Fixing AES-CTR counter bug
crypto: null - Add missing Kconfig tristate for NULL2
crypto: nx - Add forward declaration for struct crypto_aead
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-next
The i.MX clock updates for 4.3:
- Provide a better IPU clock initial settings on imx6dl for getting
HDMI and LVDS at the same time.
- Add clock driver support for i.MX6UL SoC
- Add a second clock for RTC device on i.MX31 and i.MX35
|
|
Add CAAM clock support to the i.MX6 clocking infrastructure.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The imx35 don't define clocks for rtc.
This patch add two clocks, as needed
by the mxc rtc driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The mxc rtc driver needs two clock.
It was defined only one clock, so we
define the second clock.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Clock provider drivers generally shouldn't include clk.h because
it's the consumer API. Remove the include here because this is a
provider driver.
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
