| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit ff4279618f0aec350b0fb41b2b35841324fbd96e ]
To i.MX93 which features dual Cortex-A55 cores and DSU, when using
writel_relaxed to write value to PLL registers, the value might be
buffered. To make sure the value has been written into the hardware,
using readl to read back the register could achieve the goal.
current PLL power up flow can be simplified as below:
1. writel_relaxed to set the PLL POWERUP bit;
2. readl_poll_timeout to check the PLL lock bit:
a). timeout = ktime_add_us(ktime_get(), timeout_us);
b). readl the pll the lock reg;
c). check if the pll lock bit ready
d). check if timeout
But in some corner cases, both the write in step 1 and read in
step 2 will be blocked by other bus transaction in the SoC for a
long time, saying the value into real hardware is just before step b).
That means the timeout counting has begins for quite sometime since
step a), but value still not written into real hardware until bus
released just at a point before step b).
Then there maybe chances that the pll lock bit is not ready
when readl done but the timeout happens. readl_poll_timeout will
err return due to timeout. To avoid such unexpected failure,
read back the reg to make sure the write has been done in HW
reg.
So use readl after writel_relaxed to fix the issue.
Since we are here, to avoid udelay to run before writel_relaxed, use
readl before udelay.
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Co-developed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241027-imx-clk-v1-v3-3-89152574d1d7@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 557be501c38e1864b948fc6ccdf4b035d610a2ea ]
Per i.MX93 Reference Mannual 22.4 Initialization information
1. Program appropriate value of DIV[ODIV], DIV[RDIV] and DIV[MFI]
as per Integer mode.
2. Wait for 5 μs.
3. Program the following field in CTRL register.
Set CTRL[POWERUP] to 1'b1 to enable PLL block.
4. Poll PLL_STATUS[PLL_LOCK] register, and wait till PLL_STATUS[PLL_LOCK]
is 1'b1 and pll_lock output signal is 1'b1.
5. Set CTRL[CLKMUX_EN] to 1'b1 to enable PLL output clock.
So move the CLKMUX_EN operation after PLL locked.
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Co-developed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241027-imx-clk-v1-v3-2-89152574d1d7@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
- Add 1039.5MHz clock for video PLL to fulfill the LVDS display
148.5MHz * 7 requirement
- Add 800MHz clock for ARM PLL
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240607133347.3291040-16-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
Fractional part of PLL gets lost after re-enabling the PLL. the
MFN can NOT be automatically loaded when doing frac PLL enable/disable,
So when re-enable PLL, configure mfn explicitly.
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240607133347.3291040-5-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
For video pll, it may need 519.75MHz clock frequency for
the LVDS display usage. So add 519.75MHz frequency config
support for video pll.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230628061724.2056520-3-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
Add 300MHz frequency config support on i.MX93 PLL.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230403095300.3386988-5-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
The fracn gppll could be configured in FRAC or INTEGER mode during
hardware design. The current driver only support FRAC mode, while
this patch introduces INTEGER support. When the PLL is INTEGER pll,
there is no mfn, mfd, the calculation is as below:
Fvco_clk = (Fref / DIV[RDIV] ) * DIV[MFI]
Fclko_odiv = Fvco_clk / DIV[ODIV]
In this patch, we reuse the FRAC pll logic with some condition check to
simplify the driver
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230403095300.3386988-4-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
When programming PLL, should disable Hardware control select to make PLL
controlled by register, not hardware inputs through OSCPLL.
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230403095300.3386988-3-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
The Fvco should be range 2.4GHz to 5GHz, the original table voilate the
spec, so update the table to fix it.
Fixes: c196175acdd3 ("clk: imx: clk-fracn-gppll: Add more freq config for video pll")
Fixes: 044034efbeea ("clk: imx: clk-fracn-gppll: fix mfd value")
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230403095300.3386988-2-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
Add the [484,498,445.3]MHz frequency support that will be used
by video subsystem on imx93.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220609132902.3504651-8-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
According to Reference Manual:
000b - Divide by 1
001b - Divide by 1
010b - Divide by 2
011b - Divide by 3
100b - Divide by 4
101b - Divide by 5
110b - Divide by 6
111b - Divide by 7
So only need increase rdiv by 1 when the register value is 0.
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220609132902.3504651-7-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
The PLL parameters in rate table should be directly compared with
those read from PLL registers instead of the cooked ones.
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220609132902.3504651-6-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
According to spec:
A value of 0 is disallowed and should not be programmed in this register
Fix to 1.
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220609132902.3504651-5-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
|
|
This PLL module is a Fractional-N synthesizer,
supporting 30-bit numerator and denominator. Numerator is a signed
number. It has feature to adjust fractional portion of feedback
divider dynamically. This fracn gppll is used in i.MX93.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220228020908.2810346-5-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
