| Age | Commit message (Collapse) | Author |
|---|
|
Fix variable set but not used compilation warning.
Fixes: 43b1bb4a9b3e ("clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputs")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1598338751-20607-4-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Some of the SAMA7G5 PLLs support multiple outputs (e.g. AUDIO PLL).
For these, split the PLL clock in two: fractional clock and
divider clock. In case PLLs supports multiple outputs (since these
outputs are dividers (with different settings) sharing the same
fractional part), it will register one fractional clock and multiple
divider clocks (dividers sharing the fractional clock).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-17-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In commit a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
the fractional part of PLL wasn't set on registers but it was
calculated and taken into account for determining div and mul
(see sam9x60_pll_get_best_div_mul()).
Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-7-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
According to datasheet the range of 600-1200MHz is for the
frequency generated by the fractional part of the PLL (namely
Fcorepllck according to datasheet). With this in mind the output
range of the PLL itself (fractional + div), taking into account
that the divider is 8 bits wide, is 600/256-1200Hz=2.3-1200MHz.
Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-6-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Use logical or for range check. In case bestrate is not in
characteristics->output[0].min..characteristics->output[0].max
range we should return -ERANGE.
Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-5-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
According to datasheet mul mask is on bits 31..24.
Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-4-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Move SAM9X60's PLL register offsets to PMC header so that the
definitions would also be available from arch/arm/mach-at91/pm_suspend.S.
This is necessary to disable/enable PLLA for SAM9X60 on suspend/resume.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1579522208-19523-7-git-send-email-claudiu.beznea@microchip.com
|
|
Product datasheet recommends different values for UPLL and PLLA analog control
register.
Adapt accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lkml.kernel.org/r/1573478913-19737-1-git-send-email-eugen.hristev@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The PLLs on the sam9x60 (PLLA and USB PLL) use a different register set and
programming model than the previous SoCs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
