summaryrefslogtreecommitdiff
path: root/drivers/bluetooth
AgeCommit message (Collapse)Author
2022-08-21Bluetooth: hci_intel: Add check for platform_driver_registerJiasheng Jiang
[ Upstream commit ab2d2a982ff721f4b029282d9a40602ea46a745e ] As platform_driver_register() could fail, it should be better to deal with the return value in order to maintain the code consisitency. Fixes: 1ab1f239bf17 ("Bluetooth: hci_intel: Add support for platform driver") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-08-11Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3586Hilda Wu
commit 6ad353dfc8ee3230a5e123c21da50f1b64cc4b39 upstream. Add the support ID(0x13D3, 0x3586) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3586 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-11Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3587Hilda Wu
commit 8f0054dd29373cd877db87751c143610561d549d upstream. Add the support ID(0x13D3, 0x3587) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3587 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-11Bluetooth: btusb: Add Realtek RTL8852C support ID 0x0CB8:0xC558Hilda Wu
commit 5b75ee37ebb73f58468d4cca172434324af203f1 upstream. Add the support ID(0x0CB8, 0xC558) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cb8 ProdID=c558 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-11Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04C5:0x1675Hilda Wu
commit 893fa8bc9952a36fb682ee12f0a994b5817a36d2 upstream. Add the support ID(0x04c5, 0x1675) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04c5 ProdID=1675 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-11Bluetooth: btusb: Add Realtek RTL8852C support ID 0x04CA:0x4007Hilda Wu
commit c379c96cc221767af9688a5d4758a78eea30883a upstream. Add the support ID(0x04CA, 0x4007) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=4007 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-11Bluetooth: btusb: Add support of IMC Networks PID 0x3568Aaron Ma
commit c69ecb0ea4c96b8b191cbaa0b420222a37867655 upstream. It is 13d3:3568 for MediaTek MT7922 USB Bluetooth chip. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3568 Rev=01.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=... C: #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-11Bluetooth: hci_bcm: Add DT compatible for CYW55572Hakan Jansson
commit f8cad62002a7699fd05a23b558b980b5a77defe0 upstream. CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon. Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-11Bluetooth: hci_bcm: Add BCM4349B1 variantAhmad Fatoum
commit 4f17c2b6694d0c4098f33b07ee3a696976940aa5 upstream. The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth portion can be controlled over serial. Two subversions are added for the chip, because ROM firmware reports 002.002.013 (at least for the chips I have here), while depending on patchram firmware revision, either 002.002.013 or 002.002.014 is reported. Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-06-06Bluetooth: hci_qca: Use del_timer_sync() before freeingSteven Rostedt
commit 72ef98445aca568a81c2da050532500a8345ad3a upstream. While looking at a crash report on a timer list being corrupted, which usually happens when a timer is freed while still active. This is commonly triggered by code calling del_timer() instead of del_timer_sync() just before freeing. One possible culprit is the hci_qca driver, which does exactly that. Eric mentioned that wake_retrans_timer could be rearmed via the work queue, so also move the destruction of the work queue before del_timer_sync(). Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: stable@vger.kernel.org Fixes: 0ff252c1976da ("Bluetooth: hciuart: Add support QCA chipset for UART") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-08Bluetooth: btmtksdio: Fix kernel oops in btmtksdio_interruptYake Yang
[ Upstream commit b062a0b9c1dc1ff63094337dccfe1568d5b62023 ] Fix the following kernel oops in btmtksdio_interrrupt [ 14.339134] btmtksdio_interrupt+0x28/0x54 [ 14.339139] process_sdio_pending_irqs+0x68/0x1a0 [ 14.339144] sdio_irq_work+0x40/0x70 [ 14.339154] process_one_work+0x184/0x39c [ 14.339160] worker_thread+0x228/0x3e8 [ 14.339168] kthread+0x148/0x3ac [ 14.339176] ret_from_fork+0x10/0x30 That happened because hdev->power_on is already called before sdio_set_drvdata which btmtksdio_interrupt handler relies on is not properly set up. The details are shown as the below: hci_register_dev would run queue_work(hdev->req_workqueue, &hdev->power_on) as WQ_HIGHPRI workqueue_struct to complete the power-on sequeunce and thus hci_power_on may run before sdio_set_drvdata is done in btmtksdio_probe. The hci_dev_do_open in hci_power_on would initialize the device and enable the interrupt and thus it is possible that btmtksdio_interrupt is being called right before sdio_set_drvdata is filled out. When btmtksdio_interrupt is being called and sdio_set_drvdata is not filled , the kernel oops is going to happen because btmtksdio_interrupt access an uninitialized pointer. Fixes: 9aebfd4a2200 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices") Reviewed-by: Mark Chen <markyawenchen@gmail.com> Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-04-08Bluetooth: hci_serdev: call init_rwsem() before p->open()Pavel Skripkin
[ Upstream commit 9d7cbe2b9cf5f650067df4f402fdd799d4bbb4e1 ] kvartet reported, that hci_uart_tx_wakeup() uses uninitialized rwsem. The problem was in wrong place for percpu_init_rwsem() call. hci_uart_proto::open() may register a timer whose callback may call hci_uart_tx_wakeup(). There is a chance, that hci_uart_register_device() thread won't be fast enough to call percpu_init_rwsem(). Fix it my moving percpu_init_rwsem() call before p->open(). INFO: trying to register non-static key. The code is fine but needs lockdep annotation, or maybe you didn't initialize this object before use? turning off the locking correctness validator. CPU: 2 PID: 18524 Comm: syz-executor.5 Not tainted 5.16.0-rc6 #9 ... Call Trace: <IRQ> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 assign_lock_key kernel/locking/lockdep.c:951 [inline] register_lock_class+0x148d/0x1950 kernel/locking/lockdep.c:1263 __lock_acquire+0x106/0x57e0 kernel/locking/lockdep.c:4906 lock_acquire kernel/locking/lockdep.c:5637 [inline] lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5602 percpu_down_read_trylock include/linux/percpu-rwsem.h:92 [inline] hci_uart_tx_wakeup+0x12e/0x490 drivers/bluetooth/hci_ldisc.c:124 h5_timed_event+0x32f/0x6a0 drivers/bluetooth/hci_h5.c:188 call_timer_fn+0x1a5/0x6b0 kernel/time/timer.c:1421 Fixes: d73e17281665 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops") Reported-by: Yiru Xu <xyru1999@gmail.com> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: vhci: Set HCI_QUIRK_VALID_LE_STATESLuiz Augusto von Dentz
[ Upstream commit cfb4c313be670fd4bd09650216620fa4514cdb93 ] This set HCI_QUIRK_VALID_LE_STATES quirk which is required for the likes of experimental LE simultaneous roles. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probeMiaoqian Lin
[ Upstream commit 6845667146a28c09b5dfc401c1ad112374087944 ] The function devm_gpiod_get_index() return error pointers on error. Thus devm_gpiod_get_index_optional() could return NULL and error pointers. The same as devm_gpiod_get_optional() function. Using IS_ERR_OR_NULL() check to catch error pointers. Fixes: 77131dfe ("Bluetooth: hci_qca: Replace devm_gpiod_get() with devm_gpiod_get_optional()") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: hci_bcm: Check for error irqJiasheng Jiang
[ Upstream commit b38cd3b42fba66cc538edb9cf77e07881f43f8e2 ] For the possible failure of the platform_get_irq(), the returned irq could be error number and will finally cause the failure of the request_irq(). Consider that platform_get_irq() can now in certain cases return -EPROBE_DEFER, and the consequences of letting request_irq() effectively convert that into -EINVAL, even at probe time rather than later on. So it might be better to check just now. Fixes: 0395ffc1ee05 ("Bluetooth: hci_bcm: Add PM for BCM devices") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: hci_qca: Stop IBS timer during BT OFFPanicker Harish
[ Upstream commit df1e5c51492fd93ffc293acdcc6f00698d19fedc ] The IBS timers are not stopped properly once BT OFF is triggered. we could see IBS commands being sent along with version command, so stopped IBS timers while Bluetooth is off. Fixes: 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990") Signed-off-by: Panicker Harish <quic_pharish@quicinc.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-27Bluetooth: btmtksdio: fix resume failureSean Wang
[ Upstream commit 561ae1d46a8ddcbc13162d5771f5ed6c8249e730 ] btmtksdio have to rely on MMC_PM_KEEP_POWER in pm_flags to avoid that SDIO power is being shut off during the device is in suspend. That fixes the SDIO command fails to access the bus after the device is resumed. Fixes: 7f3c563c575e7 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth") Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-01-16Bluetooth: bfusb: fix division by zero in send pathJohan Hovold
commit b5e6fa7a12572c82f1e7f2f51fbb02a322291291 upstream. Add the missing bulk-out endpoint sanity check to probe() to avoid division by zero in bfusb_send_frame() in case a malicious device has broken descriptors (or when doing descriptor fuzz testing). Note that USB core will reject URBs submitted for endpoints with zero wMaxPacketSize but that drivers doing packet-size calculations still need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip endpoint descriptors with maxpacket=0")). Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: Add support for Foxconn QCA 0xe0d0Aaron Ma
commit 1cd563ebd0dc062127a85e84f934f4c697bb43ef upstream. Add an ID of Qualcomm Bluetooth SoC WCN6855. T: Bus=05 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d0 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I:* If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: Add support for Foxconn MT7922AAaron Ma
commit 6932627425d6d3849aecd43c02158a5312895ad4 upstream. Add 2 USB IDs for MT7922A chip. These 2 devices got the same description. T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d8 Rev= 1.00 T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d9 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: Add two more Bluetooth parts for WCN6855Zijun Hu
commit d2666be51d5f09662929888dd84d1f4d38c97127 upstream. Add USB IDs (0x10ab, 0x9309) and (0x10ab, 0x9409) to usb_device_id table for WCN6855. * /sys/kernel/debug/usb/devices T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=10ab ProdID=9309 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=10ab ProdID=9409 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16Bluetooth: btusb: fix memory leak in btusb_mtk_submit_wmt_recv_urb()Mark-YW.Chen
commit 60c6a63a3d3080a62f3e0e20084f58dbeff16748 upstream. Driver should free `usb->setup_packet` to avoid the leak. $ cat /sys/kernel/debug/kmemleak unreferenced object 0xffffffa564a58080 (size 128): backtrace: [<000000007eb8dd70>] kmem_cache_alloc_trace+0x22c/0x384 [<000000008a44191d>] btusb_mtk_hci_wmt_sync+0x1ec/0x994 [btusb] [<00000000ca7189a3>] btusb_mtk_setup+0x6b8/0x13cc [btusb] [<00000000c6105069>] hci_dev_do_open+0x290/0x974 [bluetooth] [<00000000a583f8b8>] hci_power_on+0xdc/0x3cc [bluetooth] [<000000005d80e687>] process_one_work+0x514/0xc80 [<00000000f4d57637>] worker_thread+0x818/0xd0c [<00000000dc7bdb55>] kthread+0x2f8/0x3b8 [<00000000f9999513>] ret_from_fork+0x10/0x30 Fixes: a1c49c434e150 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices") Signed-off-by: Mark-YW.Chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-18Bluetooth: btmtkuart: fix a memleak in mtk_hci_wmt_syncDinghao Liu
[ Upstream commit 3e5f2d90c28f9454e421108554707620bc23269d ] bdev->evt_skb will get freed in the normal path and one error path of mtk_hci_wmt_sync, while the other error paths do not free it, which may cause a memleak. This bug is suggested by a static analysis tool, please advise. Fixes: e0b67035a90b ("Bluetooth: mediatek: update the common setup between MT7622 and other devices") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-09-03Bluetooth: btusb: check conditions before enabling USB ALT 3 for WBSPauli Virtanen
commit 55981d3541812234e687062926ff199c83f79a39 upstream. Some USB BT adapters don't satisfy the MTU requirement mentioned in commit e848dbd364ac ("Bluetooth: btusb: Add support USB ALT 3 for WBS") and have ALT 3 setting that produces no/garbled audio. Some adapters with larger MTU were also reported to have problems with ALT 3. Add a flag and check it and MTU before selecting ALT 3, falling back to ALT 1. Enable the flag for Realtek, restoring the previous behavior for non-Realtek devices. Tested with USB adapters (mtu<72, no/garbled sound with ALT3, ALT1 works) BCM20702A1 0b05:17cb, CSR8510A10 0a12:0001, and (mtu>=72, ALT3 works) RTL8761BU 0bda:8771, Intel AX200 8087:0029 (after disabling ALT6). Also got reports for (mtu>=72, ALT 3 reported to produce bad audio) Intel 8087:0a2b. Signed-off-by: Pauli Virtanen <pav@iki.fi> Fixes: e848dbd364ac ("Bluetooth: btusb: Add support USB ALT 3 for WBS") Tested-by: Michał Kępień <kernel@kempniu.pl> Tested-by: Jonathan Lampérth <jon@h4n.dev> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-07-19Bluetooth: btusb: fix bt fiwmare downloading failure issue for qca btsoc.Tim Jiang
[ Upstream commit 4f00bfb372674d586c4a261bfc595cbce101fbb6 ] This is btsoc timing issue, after host start to downloading bt firmware, ep2 need time to switch from function acl to function dfu, so host add 20ms delay as workaround. Signed-off-by: Tim Jiang <tjiang@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-07-19Bluetooth: btusb: Add support USB ALT 3 for WBSHilda Wu
[ Upstream commit e848dbd364aca44c9d23c04bef964fab79e2b34f ] Because mSBC frames do not need to be aligned to the SCO packet boundary. Using USB ALT 3 let HCI payload >= 60 bytes, let mSBC data satisfy 60 Bytes avoid payload unaligned situation and fixed some headset no voise issue. USB Alt 3 supported also need HFP support transparent MTU in 72 Bytes. Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-07-19Bluetooth: btusb: Add a new QCA_ROME device (0cf3:e500)Daniel Lenski
[ Upstream commit 0324d19cb99804d99e42c990b8b1e191575a091b ] This patch adds the 0cf3:e500 Bluetooth device (from a QCA9377 board) as a QCA_ROME device. It appears to be functionally identical to another device ID, also from a QCA9377 board, which was previously marked as QCA_ROME in 0a03f98b98c201191e3ba15a0e33f46d8660e1fd ("Bluetooth: Add a new 04ca:3015 QCA_ROME device"). Without this patch, the WiFi side of the QCA9377 board is slow or unusable when the Bluetooth side is in use. See https://askubuntu.com/a/1137852 for another report of QCA_ROME fixing this issue for this device ID. /sys/kernel/debug/usb/devices: T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e500 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Daniel Lenski <dlenski@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-07-19Bluetooth: btusb: Fixed too many in-token issue for Mediatek Chip.mark-yw.chen
[ Upstream commit 8454ed9ff9647e31e061fb5eb2e39ce79bc5e960 ] This patch reduce in-token during download patch procedure. Don't submit urb for polling event before sending hci command. Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-07-14Bluetooth: btqca: Don't modify firmware contents in-placeConnor Abbott
commit b43ca511178ed0ab6fd2405df28cf9e100273020 upstream. struct firmware::data is marked const, and when the firmware is compressed with xz (default at least with Fedora) it's mapped read-only which results in a crash: BUG: unable to handle page fault for address: ffffae57c0ca5047 PGD 100000067 P4D 100000067 PUD 1001ce067 PMD 10165a067 PTE 8000000112bba161 Oops: 0003 [#1] SMP NOPTI CPU: 3 PID: 204 Comm: kworker/u17:0 Not tainted 5.12.1-test+ #1 Hardware name: Dell Inc. XPS 13 9310/0F7M4C, BIOS 1.2.5 12/10/2020 Workqueue: hci0 hci_power_on [bluetooth] RIP: 0010:qca_download_firmware+0x27c/0x4e0 [btqca] Code: 1b 75 04 80 48 0c 01 0f b7 c6 8d 54 02 0c 41 39 d7 0f 8e 62 fe ff ff 48 63 c2 4c 01 e8 0f b7 38 0f b7 70 02 66 83 ff 11 75 d3 <80> 48 0c 80 41 83 fc 03 7e 6e 88 58 0d eb ce 41 0f b6 45 0e 48 8b RSP: 0018:ffffae57c08dfc68 EFLAGS: 00010246 RAX: ffffae57c0ca503b RBX: 000000000000000e RCX: 0000000000000000 RDX: 0000000000000037 RSI: 0000000000000006 RDI: 0000000000000011 RBP: ffff978d9949e000 R08: ffff978d84ed7540 R09: ffffae57c0ca5000 R10: 000000000010cd00 R11: 0000000000000001 R12: 0000000000000005 R13: ffffae57c0ca5004 R14: ffff978d98ca8680 R15: 00000000000016a9 FS: 0000000000000000(0000) GS:ffff9794ef6c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffae57c0ca5047 CR3: 0000000113d5a004 CR4: 0000000000770ee0 PKRU: 55555554 Call Trace: qca_uart_setup+0x2cb/0x1390 [btqca] ? qca_read_soc_version+0x136/0x220 [btqca] qca_setup+0x288/0xab0 [hci_uart] hci_dev_do_open+0x1f3/0x780 [bluetooth] ? try_to_wake_up+0x1c1/0x4f0 hci_power_on+0x3f/0x200 [bluetooth] process_one_work+0x1ec/0x380 worker_thread+0x53/0x3e0 ? process_one_work+0x380/0x380 kthread+0x11b/0x140 ? kthread_associate_blkcg+0xa0/0xa0 ret_from_fork+0x1f/0x30 Modules linked in: llc ip_set nf_tables nfnetlink snd_soc_skl_hda_dsp(+) ip6table_filter snd_soc_hdac_hdmi ip6_tables qrtr_mhi iptable_filter snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic s> dell_wmi_sysman(+) dell_smbios snd dcdbas mhi vfat videobuf2_vmalloc i2c_i801 videobuf2_memops videobuf2_v4l2 dell_wmi_descriptor fat wmi_bmof soundcore i2c_smbus videobuf2_common libarc4 mei_me mei hid_se> i2c_hid_acpi i2c_hid video pinctrl_tigerlake fuse CR2: ffffae57c0ca5047 This also seems to fix a failure to suspend due to the firmware download on bootup getting interrupted by the crash: Bluetooth: hci0: SSR or FW download time out PM: dpm_run_callback(): acpi_subsys_suspend+0x0/0x60 returns -110 PM: Device serial0-0 failed to suspend: error -110 PM: Some devices failed to suspend, or early wake event detected Fixes: 83e8196 ("Bluetooth: btqca: Introduce generic QCA ROME support") Cc: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org> Cc: stable@vger.kernel.org Signed-off-by: Connor Abbott <cwabbott0@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-07-14Bluetooth: hci_qca: fix potential GPFPavel Skripkin
commit 59f90f1351282ea2dbd0c59098fd9bb2634e920e upstream. In qca_power_shutdown() qcadev local variable is initialized by hu->serdev.dev private data, but hu->serdev can be NULL and there is a check for it. Since, qcadev is not used before if (!hu->serdev) return; we can move its initialization after this "if" to prevent GPF. Fixes: 5559904ccc08 ("Bluetooth: hci_qca: Add QCA Rome power off support to the qca_power_shutdown()") Cc: stable@vger.kernel.org # v5.6+ Cc: Rocky Liao <rjliao@codeaurora.org> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-06-18Bluetooth: Add a new USB ID for RTL8822CELarry Finger
[ Upstream commit 4d96d3b0efee6416ef0d61b76aaac6f4a2e15b12 ] Some models of the RTL8822ce utilize a different USB ID. Add this new one to the Bluetooth driver. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-05-19Bluetooth: btusb: Enable quirk boolean flag for Mediatek Chip.mark-yw.chen
[ Upstream commit 27e554a4fcd84e499bf0a82122b8c4c3f1de38b6 ] Adding support LE scatternet and WBS for Mediatek Chip Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-11Bluetooth: btqca: Add valid le states quirkAbhishek Pandit-Subedi
[ Upstream commit 547801380ec7e6104ea679f599d03c342b4b39a0 ] WCN3991 supports connectable advertisements so we need to add the valid le states quirk so the 'central-peripheral' role is exposed in userspace. Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-07Bluetooth: hci_h5: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for btrtlClaire Chang
[ Upstream commit 7f9f2c3f7d99b8ae773459c74ac5e99a0dd46db9 ] Realtek Bluetooth controllers can do both LE scan and BR/EDR inquiry at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk. Signed-off-by: Claire Chang <tientzu@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-04tty: convert tty_ldisc_ops 'read()' function to take a kernel pointerLinus Torvalds
[ Upstream commit 3b830a9c34d5897be07176ce4e6f2d75e2c8cfd7 ] The tty line discipline .read() function was passed the final user pointer destination as an argument, which doesn't match the 'write()' function, and makes it very inconvenient to do a splice method for ttys. This is a conversion to use a kernel buffer instead. NOTE! It does this by passing the tty line discipline ->read() function an additional "cookie" to fill in, and an offset into the cookie data. The line discipline can fill in the cookie data with its own private information, and then the reader will repeat the read until either the cookie is cleared or it runs out of data. The only real user of this is N_HDLC, which can use this to handle big packets, even if the kernel buffer is smaller than the whole packet. Cc: Christoph Hellwig <hch@lst.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-04Bluetooth: btusb: Fix memory leak in btusb_mtk_wmt_recvJupeng Zhong
[ Upstream commit de71a6cb4bf24d8993b9ca90d1ddb131b60251a1 ] In btusb_mtk_wmt_recv if skb_clone fails, the alocated skb should be released. Omit the labels “err_out” and “err_free_skb” in this function implementation so that the desired exception handling code would be directly specified in the affected if branches. Fixes: a1c49c434e15 ("btusb: Add protocol support for MediaTek MT7668U USB devices") Signed-off-by: Jupeng Zhong <zhongjupeng@yulong.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-04Bluetooth: hci_qca: Fix memleak in qca_controller_memdumpDinghao Liu
[ Upstream commit 71f8e707557b9bc25dc90a59a752528d4e7c1cbf ] When __le32_to_cpu() fails, qca_memdump should be freed just like when vmalloc() fails. Fixes: d841502c79e3f ("Bluetooth: hci_qca: Collect controller memory dump during SSR") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-04Bluetooth: hci_uart: Fix a race for write_work schedulingClaire Chang
[ Upstream commit afe0b1c86458f121b085271e4f3034017a90d4a3 ] In hci_uart_write_work, there is a loop/goto checking the value of HCI_UART_TX_WAKEUP. If HCI_UART_TX_WAKEUP is set again, it keeps trying hci_uart_dequeue; otherwise, it clears HCI_UART_SENDING and returns. In hci_uart_tx_wakeup, if HCI_UART_SENDING is already set, it sets HCI_UART_TX_WAKEUP, skips schedule_work and assumes the running/pending hci_uart_write_work worker will do hci_uart_dequeue properly. However, if the HCI_UART_SENDING check in hci_uart_tx_wakeup is done after the loop breaks, but before HCI_UART_SENDING is cleared in hci_uart_write_work, the schedule_work is skipped incorrectly. Fix this race by changing the order of HCI_UART_SENDING and HCI_UART_TX_WAKEUP modification. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: 82f5169bf3d3 ("Bluetooth: hci_uart: add serdev driver support library") Signed-off-by: Claire Chang <tientzu@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-04Bluetooth: btqcomsmd: Fix a resource leak in error handling paths in the ↵Christophe JAILLET
probe function [ Upstream commit 9a39a927be01d89e53f04304ab99a8761e08910d ] Some resource should be released in the error handling path of the probe function, as already done in the remove function. The remove function was fixed in commit 5052de8deff5 ("soc: qcom: smd: Transition client drivers from smd to rpmsg") Fixes: 1511cc750c3d ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-02-26Bluetooth: btusb: Some Qualcomm Bluetooth adapters stop workingHui Wang
commit 234f414efd1164786269849b4fbb533d6c9cdbbf upstream. This issue starts from linux-5.10-rc1, I reproduced this issue on my Dell Inspiron 7447 with BT adapter 0cf3:e005, the kernel will print out: "Bluetooth: hci0: don't support firmware rome 0x31010000", and someone else also reported the similar issue to bugzilla #211571. I found this is a regression introduced by 'commit b40f58b97386 ("Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 support"), the patch assumed that if high ROM version is not zero, it is an adapter on WCN6855, but many old adapters don't need to load rampatch or nvm, and they have non-zero high ROM version. To fix it, let the driver match the rom_version in the qca_devices_table first, if there is no entry matched, check the high ROM version, if it is not zero, we assume this adapter is ready to work and no need to load rampatch and nvm like previously. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211571 Fixes: b40f58b97386 ("Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 support") Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-02-23Bluetooth: btusb: Always fallback to alt 1 for WBSTrent Piepho
commit 517b693351a2d04f3af1fc0e506ac7e1346094de upstream. When alt mode 6 is not available, fallback to the kernel <= 5.7 behavior of always using alt mode 1. Prior to kernel 5.8, btusb would always use alt mode 1 for WBS (Wide Band Speech aka mSBC aka transparent SCO). In commit baac6276c0a9 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints") this was changed to use alt mode 6, which is the recommended mode in the Bluetooth spec (Specifications of the Bluetooth System, v5.0, Vol 4.B §2.2.1). However, many if not most BT USB adapters do not support alt mode 6. In fact, I have been unable to find any which do. In kernel 5.8, this was changed to use alt mode 6, and if not available, use alt mode 0. But mode 0 has a zero byte max packet length and can not possibly work. It is just there as a zero-bandwidth dummy mode to work around a USB flaw that would prevent device enumeration if insufficient bandwidth were available for the lowest isoc mode supported. In effect, WBS was broken for all USB-BT adapters that do not support alt 6, which appears to nearly all of them. Then in commit 461f95f04f19 ("Bluetooth: btusb: USB alternate setting 1 for WBS") the 5.7 behavior was restored, but only for Realtek adapters. I've tested a Broadcom BRCM20702A and CSR 8510 adapter, both work with the 5.7 behavior and do not with the 5.8. So get rid of the Realtek specific flag and use the 5.7 behavior for all adapters as a fallback when alt 6 is not available. This was the kernel's behavior prior to 5.8 and I can find no adapters for which it is not correct. And even if there is an adapter for which this does not work, the current behavior would be to fall back to alt 0, which can not possibly work either, and so is no better. Signed-off-by: Trent Piepho <tpiepho@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: Salvatore Bonaccorso <carnil@debian.org> Cc: Sjoerd Simons <sjoerd@luon.net> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-12Bluetooth: revert: hci_h5: close serdev device and free hu in h5_closeHans de Goede
commit 5c3b5796866f85354a5ce76a28f8ffba0dcefc7e upstream. There have been multiple revisions of the patch fix the h5->rx_skb leak. Accidentally the first revision (which is buggy) and v5 have both been merged: v1 commit 70f259a3f427 ("Bluetooth: hci_h5: close serdev device and free hu in h5_close"); v5 commit 855af2d74c87 ("Bluetooth: hci_h5: fix memory leak in h5_close") The correct v5 makes changes slightly higher up in the h5_close() function, which allowed both versions to get merged without conflict. The changes from v1 unconditionally frees the h5 data struct, this is wrong because in the serdev enumeration case the memory is allocated in h5_serdev_probe() like this: h5 = devm_kzalloc(dev, sizeof(*h5), GFP_KERNEL); So its lifetime is tied to the lifetime of the driver being bound to the serdev and it is automatically freed when the driver gets unbound. In the serdev case the same h5 struct is re-used over h5_close() and h5_open() calls and thus MUST not be free-ed in h5_close(). The serdev_device_close() added to h5_close() is incorrect in the same way, serdev_device_close() is called on driver unbound too and also MUST no be called from h5_close(). This reverts the changes made by merging v1 of the patch, so that just the changes of the correct v5 remain. Cc: Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-06Bluetooth: hci_h5: close serdev device and free hu in h5_closeAnant Thazhemadam
commit 70f259a3f4276b71db365b1d6ff1eab805ea6ec3 upstream. When h5_close() gets called, the memory allocated for the hu gets freed only if hu->serdev doesn't exist. This leads to a memory leak. So when h5_close() is requested, close the serdev device instance and free the memory allocated to the hu entirely instead. Fixes: https://syzkaller.appspot.com/bug?extid=6ce141c55b2f7aafd1c4 Reported-by: syzbot+6ce141c55b2f7aafd1c4@syzkaller.appspotmail.com Tested-by: syzbot+6ce141c55b2f7aafd1c4@syzkaller.appspotmail.com Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-30Bluetooth: btusb: Fix detection of some fake CSR controllers with a ↵Hans de Goede
bcdDevice val of 0x0134 [ Upstream commit d74e0ae7e03032b47b8631cc1e52a7ae1ce988c0 ] Commit cde1a8a99287 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers") made the detection of fake controllers more generic fixing it for much of the newer fakes / clones. But this does not work for a fake CSR controller with a bcdDevice value of 0x0134, which was correctly identified as fake before this change. Add an extra check for this special case, checking for a combination of a bcdDevice value of 0x0134, together with a lmp_subver of 0x0c5c and a hci_ver of BLUETOOTH_VER_2_0. The chip inside this fake dongle is marked as with "clockwise cw6629d". Fixes: cde1a8a99287 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-12-30Bluetooth: btmtksdio: Add the missed release_firmware() in mtk_setup_firmware()Jing Xiangfeng
[ Upstream commit b73b5781a85c03113476f62346c390f0277baa4b ] mtk_setup_firmware() misses to call release_firmware() in an error path. Jump to free_fw to fix it. Fixes: 737cd06072a7 ("Bluetooth: btmtksdio: fix up firmware download sequence") Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-12-30Bluetooth: btusb: Add the missed release_firmware() in ↵Jing Xiangfeng
btusb_mtk_setup_firmware() [ Upstream commit d1e9d232e1e60fa63df1b836ec3ecba5abd3fa9d ] btusb_mtk_setup_firmware() misses to call release_firmware() in an error path. Jump to err_release_fw to fix it. Fixes: f645125711c8 ("Bluetooth: btusb: fix up firmware download sequence") Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-12-30Bluetooth: hci_h5: fix memory leak in h5_closeAnant Thazhemadam
[ Upstream commit 855af2d74c870d747bf53509f8b2d7b9dc9ee2c3 ] When h5_close() is called, h5 is directly freed when !hu->serdev. However, h5->rx_skb is not freed, which causes a memory leak. Freeing h5->rx_skb and setting it to NULL, fixes this memory leak. Fixes: ce945552fde4 ("Bluetooth: hci_h5: Add support for serdev enumerated devices") Reported-by: syzbot+6ce141c55b2f7aafd1c4@syzkaller.appspotmail.com Tested-by: syzbot+6ce141c55b2f7aafd1c4@syzkaller.appspotmail.com Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-30Bluetooth: btintel: Replace zero-length array with flexible-array memberGustavo A. R. Silva
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use “flexible array members”[1] for these cases. The older style of one-element or zero-length arrays should no longer be used[2]. [1] https://en.wikipedia.org/wiki/Flexible_array_member [2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-10-15Merge tag 'net-next-5.10' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Jakub Kicinski: - Add redirect_neigh() BPF packet redirect helper, allowing to limit stack traversal in common container configs and improving TCP back-pressure. Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain. - Expand netlink policy support and improve policy export to user space. (Ge)netlink core performs request validation according to declared policies. Expand the expressiveness of those policies (min/max length and bitmasks). Allow dumping policies for particular commands. This is used for feature discovery by user space (instead of kernel version parsing or trial and error). - Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge. - Allow more than 255 IPv4 multicast interfaces. - Add support for Type of Service (ToS) reflection in SYN/SYN-ACK packets of TCPv6. - In Multi-patch TCP (MPTCP) support concurrent transmission of data on multiple subflows in a load balancing scenario. Enhance advertising addresses via the RM_ADDR/ADD_ADDR options. - Support SMC-Dv2 version of SMC, which enables multi-subnet deployments. - Allow more calls to same peer in RxRPC. - Support two new Controller Area Network (CAN) protocols - CAN-FD and ISO 15765-2:2016. - Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit kernel problem. - Add TC actions for implementing MPLS L2 VPNs. - Improve nexthop code - e.g. handle various corner cases when nexthop objects are removed from groups better, skip unnecessary notifications and make it easier to offload nexthops into HW by converting to a blocking notifier. - Support adding and consuming TCP header options by BPF programs, opening the doors for easy experimental and deployment-specific TCP option use. - Reorganize TCP congestion control (CC) initialization to simplify life of TCP CC implemented in BPF. - Add support for shipping BPF programs with the kernel and loading them early on boot via the User Mode Driver mechanism, hence reusing all the user space infra we have. - Support sleepable BPF programs, initially targeting LSM and tracing. - Add bpf_d_path() helper for returning full path for given 'struct path'. - Make bpf_tail_call compatible with bpf-to-bpf calls. - Allow BPF programs to call map_update_elem on sockmaps. - Add BPF Type Format (BTF) support for type and enum discovery, as well as support for using BTF within the kernel itself (current use is for pretty printing structures). - Support listing and getting information about bpf_links via the bpf syscall. - Enhance kernel interfaces around NIC firmware update. Allow specifying overwrite mask to control if settings etc. are reset during update; report expected max time operation may take to users; support firmware activation without machine reboot incl. limits of how much impact reset may have (e.g. dropping link or not). - Extend ethtool configuration interface to report IEEE-standard counters, to limit the need for per-vendor logic in user space. - Adopt or extend devlink use for debug, monitoring, fw update in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx, dpaa2-eth). - In mlxsw expose critical and emergency SFP module temperature alarms. Refactor port buffer handling to make the defaults more suitable and support setting these values explicitly via the DCBNL interface. - Add XDP support for Intel's igb driver. - Support offloading TC flower classification and filtering rules to mscc_ocelot switches. - Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as fixed interval period pulse generator and one-step timestamping in dpaa-eth. - Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3) offload. - Add Lynx PHY/PCS MDIO module, and convert various drivers which have this HW to use it. Convert mvpp2 to split PCS. - Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as 7-port Mediatek MT7531 IP. - Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver, and wcn3680 support in wcn36xx. - Improve performance for packets which don't require much offloads on recent Mellanox NICs by 20% by making multiple packets share a descriptor entry. - Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto subtree to drivers/net. Move MDIO drivers out of the phy directory. - Clean up a lot of W=1 warnings, reportedly the actively developed subsections of networking drivers should now build W=1 warning free. - Make sure drivers don't use in_interrupt() to dynamically adapt their code. Convert tasklets to use new tasklet_setup API (sadly this conversion is not yet complete). * tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits) Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH" net, sockmap: Don't call bpf_prog_put() on NULL pointer bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo bpf, sockmap: Add locking annotations to iterator netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements net: fix pos incrementment in ipv6_route_seq_next net/smc: fix invalid return code in smcd_new_buf_create() net/smc: fix valid DMBE buffer sizes net/smc: fix use-after-free of delayed events bpfilter: Fix build error with CONFIG_BPFILTER_UMH cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info bpf: Fix register equivalence tracking. rxrpc: Fix loss of final ack on shutdown rxrpc: Fix bundle counting for exclusive connections netfilter: restore NF_INET_NUMHOOKS ibmveth: Identify ingress large send packets. ibmveth: Switch order of ibmveth_helper calls. cxgb4: handle 4-tuple PEDIT to NAT mode translation selftests: Add VRF route leaking tests ...
2020-09-27Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 supportRocky Liao
This patch add support for WCN6855 i.e. patch and nvm download support. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e600 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Rocky Liao <rjliao@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 11:57:02 +0000