| Age | Commit message (Collapse) | Author |
|---|
|
The current OMAP dmtimer probe does not check for the return
status of pm_runtime_get_sync() before initializing the timer
registers. Any timer with missing hwmod data would return a
failure here, and the access of registers without enabling the
clocks for the timer would trigger a l3_noc interrupt and a
kernel boot hang. Add proper checking so that the probe would
return a failure graciously without hanging the kernel boot.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The family information in the soc-bus data is currently
not classified properly for AM33xx devices, and a read
of /sys/bus/soc/devices/soc0/family currently shows
"Unknown". Fix the same.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds missing dma DTS definitions for omap aes and sham drivers.
Without it kernel drivers do not work for device tree based booting
while it works for legacy booting on general purpose SoCs.
Note that further changes are still needed for high secure SoCs. But since
that never worked in legacy boot mode either, those will be sent separately.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
I upgraded my u-boot and noticed that wl12xx stopped working.
Turns out the kernel is not setting the quirk for the MMC2
copy clock while the eariler bootloader I had was setting it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.0/fixes
ARM: OMAP2+: first set of hwmod and PRCM fixes for v4.0-rc
This series fixes the following bugs:
- a lockdep problem with the OMAP hwmod code;
- incorrect PCIe hwmod data for the DRA7xx chips;
- the clockdomain handling in the hardreset deassertion code,
preventing idle;
- the use of an IRQ status register rather than an IRQ enable register
in the OMAP4 PRM code.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.0-rc/20150301165949/
|
|
Enable TWL4030_USB which is used at least on Nokia N900/N950/N9 (OMAP3)
and BeagleBoard.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719f61 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb91: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes 85dc74e9 (ARM: dts: omap5 clock data)
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull arch/metag fix from James Hogan:
"This is just a single patch to fix the KSTK_EIP() and KSTK_ESP()
macros for metag which have always been erronously returning the PC
and stack pointer of the task's kernel context rather than from its
user context saved at entry from userland into the kernel, which
affects the contents of /proc/<pid>/maps and /proc/<pid>/stat"
* tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Fix KSTK_EIP() and KSTK_ESP() macros
|
|
This was incorrectly reading the irq status registers during the save
and clear, instead of the irq enable. This worked because there is only
one user for the prcm interrupts currently, namely the io-chain. Whenever
the function was called, an io-chain interrupt was both pending and
enabled.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Deasserting hardreset increases the usecount for the hwmod parent clockdomain
always, however usecount is only decreased at end in certain error cases.
This causes software supervised clockdomains to remain always on, preventing
idle. Fixed by always releasing the hwmods clockdomain parent when exiting
the function.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Carlos Hernandez <ceh@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A CR4-shadow 32-bit init fix, plus two typo fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Init per-cpu shadow copy of CR4 on 32-bit CPUs too
x86/platform/intel-mid: Fix trivial printk message typo in intel_mid_arch_setup()
x86/cpu/intel: Fix trivial typo in intel_tlb_table[]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Three clockevents/clocksource driver fixes"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: pxa: Fix section mismatch
clocksource: mtk: Fix race conditions in probe code
clockevents: asm9260: Fix compilation error with sparc/sparc64 allyesconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two kprobes fixes and a handful of tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Make sparc64 arch point to sparc
perf symbols: Define EM_AARCH64 for older OSes
perf top: Fix SIGBUS on sparc64
perf tools: Fix probing for PERF_FLAG_FD_CLOEXEC flag
perf tools: Fix pthread_attr_setaffinity_np build error
perf tools: Define _GNU_SOURCE on pthread_attr_setaffinity_np feature check
perf bench: Fix order of arguments to memcpy_alloc_mem
kprobes/x86: Check for invalid ftrace location in __recover_probed_insn()
kprobes/x86: Use 5-byte NOP when the code might be modified by ftrace
|
|
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: add missing __PAGETABLE_{PUD,PMD}_FOLDED defines
mm: page_alloc: revert inadvertent !__GFP_FS retry behavior change
kernel/sys.c: fix UNAME26 for 4.0
mm: memcontrol: use "max" instead of "infinity" in control knobs
zram: use proper type to update max_used_pages
drivers/rtc/rtc-ds1685.c: fix conditional in ds1685_rtc_sysfs_time_regs_{show,store}
nilfs2: fix potential memory overrun on inode
scripts/gdb: add empty package initialization script
rtc: ds1685: remove superfluous checks for out-of-range u8 values
rtc: ds1685: fix ds1685_rtc_alarm_irq_enable build error
memcg: fix low limit calculation
mm/nommu: fix memory leak
ocfs2: update web page + git tree in documentation
|
|
Core mm expects __PAGETABLE_{PUD,PMD}_FOLDED to be defined if these page
table levels folded. Usually, these defines are provided by
<asm-generic/pgtable-nopmd.h> and <asm-generic/pgtable-nopud.h>.
But some architectures fold page table levels in a custom way. They
need to define these macros themself. This patch adds missing defines.
The patch fixes mm->nr_pmds underflow and eliminates dead __pmd_alloc()
and __pud_alloc() on architectures without these page table levels.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit:
1e02ce4cccdc ("x86: Store a per-cpu shadow copy of CR4")
added a shadow CR4 such that reads and writes that do not
modify the CR4 execute much faster than always reading the
register itself.
The change modified cpu_init() in common.c, so that the
shadow CR4 gets initialized before anything uses it.
Unfortunately, there's two cpu_init()s in common.c. There's
one for 64-bit and one for 32-bit. The commit only added
the shadow init to the 64-bit path, but the 32-bit path
needs the init too.
Link: http://lkml.kernel.org/r/20150227125208.71c36402@gandalf.local.home Fixes: 1e02ce4cccdc "x86: Store a per-cpu shadow copy of CR4"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20150227145019.2bdd4354@gandalf.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"The arm-soc bug fixes this time around are mostly for the omap
platform, coming from a pull request from Tony Lindgren and are almost
entirely fixing dts files.
The other two changes enable support for the shmobile platform in
generic armv7 kernels and change some properties in the ARM64
reference board dts files"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Enable shmobile platforms
arm64: Add L2 cache topology to ARM Ltd boards/models
ARM: dts: am335x-bone*: usb0 is hardwired for peripheral
ARM: dts: dra7x-evm: beagle-x15: Fix USB Host
ARM: omap2plus_defconfig: Fix SATA boot
ARM: omap2plus_defconfig: Enable OMAP NAND BCH driver
ARM: dts: dra7: Correct the dma controller's property names
ARM: dts: omap5: Correct the dma controller's property names
ARM: dts: omap4: Correct the dma controller's property names
ARM: dts: omap3: Correct the dma controller's property names
ARM: dts: omap2: Correct the dma controller's property names
ARM: dts: am437x-idk: fix sleep pinctrl state
ARM: omap2plus_defconfig: enable TPS62362 regulator
ARM: dts: am437x-idk: fix TPS62362 i2c bus
ARM: dts: n900: Fix offset for smc91x ethernet
ARM: dts: n900: fix i2c bus numbering
ARM: dts: Fix USB dts configuration for dm816x
ARM: dts: OMAP5: Fix SATA PHY node
ARM: dts: DRA7: Fix SATA PHY node
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"Various arm64 fixes:
- ftrace branch generation fix
- branch instruction encoding fix
- include files, guards and unused prototypes clean-up
- minor VDSO ABI fix (clock_getres)
- PSCI functions moved to .S to avoid compilation error with gcc 5
- pte_modify fix to not ignore the mapping type
- crypto: AES interleaved increased to 4x (for performance reasons)
- text patching fix for modules
- swiotlb increased back to 64MB
- copy_siginfo_to_user32() fix for big endian"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cpuidle: add asm/proc-fns.h inclusion
arm64: compat Fix siginfo_t -> compat_siginfo_t conversion on big endian
arm64: Increase the swiotlb buffer size 64MB
arm64: Fix text patching logic when using fixmap
arm64: crypto: increase AES interleave to 4x
arm64: enable PTE type bit in the mask for pte_modify
arm64: mm: remove unused functions and variable protoypes
arm64: psci: move psci firmware calls out of line
arm64: vdso: minor ABI fix for clock_getres
arm64: guard asm/assembler.h against multiple inclusions
arm64: insn: fix compare-and-branch encodings
arm64: ftrace: fix ftrace_modify_graph_caller for branch replace
|
|
ARM64 CPUidle driver requires the cpu_do_idle function so that it can
be used to enter the shallowest idle state, and it is declared in
asm/proc-fns.h.
The current ARM64 CPUidle driver does not include asm/proc-fns.h
explicitly and it has so far relied on implicit inclusion from other
header files.
Owing to some header dependencies reshuffling this currently triggers
build failures when CONFIG_ARM64_64K_PAGES=y:
drivers/cpuidle/cpuidle-arm64.c: In function "arm64_enter_idle_state"
drivers/cpuidle/cpuidle-arm64.c:42:3: error: implicit declaration of
function "cpu_do_idle" [-Werror=implicit-function-declaration]
cpu_do_idle();
^
This patch adds the explicit inclusion of the asm/proc-fns.h header file
in the arm64 asm/cpuidle.h header file, so that the build breakage is fixed
and the required header inclusion is added to the appropriate arch back-end
CPUidle header, already included by the CPUidle arm64 driver, where
CPUidle arch related function declarations belong.
Reported-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The native (64-bit) sigval_t union contains sival_int (32-bit) and
sival_ptr (64-bit). When a compat application invokes a syscall that
takes a sigval_t value (as part of a larger structure, e.g.
compat_sys_mq_notify, compat_sys_timer_create), the compat_sigval_t
union is converted to the native sigval_t with sival_int overlapping
with either the least or the most significant half of sival_ptr,
depending on endianness. When the corresponding signal is delivered to a
compat application, on big endian the current (compat_uptr_t)sival_ptr
cast always returns 0 since sival_int corresponds to the top part of
sival_ptr. This patch fixes copy_siginfo_to_user32() so that sival_int
is copied to the compat_siginfo_t structure.
Cc: <stable@vger.kernel.org>
Reported-by: Bamvor Jian Zhang <bamvor.zhangjian@huawei.com>
Tested-by: Bamvor Jian Zhang <bamvor.zhangjian@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
With commit 3690951fc6d4 (arm64: Use swiotlb late initialisation), the
swiotlb buffer size is limited to MAX_ORDER_NR_PAGES. However, there are
platforms with 32-bit only devices that require bounce buffering via
swiotlb. This patch changes the swiotlb initialisation to an early 64MB
memblock allocation. In order to get the swiotlb buffer correctly
allocated (via memblock_virt_alloc_low_nopanic), this patch also defines
ARCH_LOW_ADDRESS_LIMIT to the maximum physical address capable of 32-bit
DMA.
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Patch 2f896d586610 ("arm64: use fixmap for text patching") changed
the way we patch the kernel text, using a fixmap when the kernel or
modules are flagged as read only.
Unfortunately, a flaw in the logic makes it fall over when patching
modules without CONFIG_DEBUG_SET_MODULE_RONX enabled:
[...]
[ 32.032636] Call trace:
[ 32.032716] [<fffffe00003da0dc>] __copy_to_user+0x2c/0x60
[ 32.032837] [<fffffe0000099f08>] __aarch64_insn_write+0x94/0xf8
[ 32.033027] [<fffffe000009a0a0>] aarch64_insn_patch_text_nosync+0x18/0x58
[ 32.033200] [<fffffe000009c3ec>] ftrace_modify_code+0x58/0x84
[ 32.033363] [<fffffe000009c4e4>] ftrace_make_nop+0x3c/0x58
[ 32.033532] [<fffffe0000164420>] ftrace_process_locs+0x3d0/0x5c8
[ 32.033709] [<fffffe00001661cc>] ftrace_module_init+0x28/0x34
[ 32.033882] [<fffffe0000135148>] load_module+0xbb8/0xfc4
[ 32.034044] [<fffffe0000135714>] SyS_finit_module+0x94/0xc4
[...]
This is triggered by the use of virt_to_page() on a module address,
which ends to pointing to Nowhereland if you're lucky, or corrupt
your precious data if not.
This patch fixes the logic by mimicking what is done on arm:
- If we're patching a module and CONFIG_DEBUG_SET_MODULE_RONX is set,
use vmalloc_to_page().
- If we're patching the kernel and CONFIG_DEBUG_RODATA is set,
use virt_to_page().
- Otherwise, use the provided address, as we can write to it directly.
Tested on 4.0-rc1 as a KVM guest.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laura Abbott <lauraa@codeaurora.org>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch increases the interleave factor for parallel AES modes
to 4x. This improves performance on Cortex-A57 by ~35%. This is
due to the 3-cycle latency of AES instructions on the A57's
relatively deep pipeline (compared to Cortex-A53 where the AES
instruction latency is only 2 cycles).
At the same time, disable inline expansion of the core AES functions,
as the performance benefit of this feature is negligible.
Measured on AMD Seattle (using tcrypt.ko mode=500 sec=1):
Baseline (2x interleave, inline expansion)
------------------------------------------
testing speed of async cbc(aes) (cbc-aes-ce) decryption
test 4 (128 bit key, 8192 byte blocks): 95545 operations in 1 seconds
test 14 (256 bit key, 8192 byte blocks): 68496 operations in 1 seconds
This patch (4x interleave, no inline expansion)
-----------------------------------------------
testing speed of async cbc(aes) (cbc-aes-ce) decryption
test 4 (128 bit key, 8192 byte blocks): 124735 operations in 1 seconds
test 14 (256 bit key, 8192 byte blocks): 92328 operations in 1 seconds
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Caught during Trinity testing. The pte_modify does not allow
modification for PTE type bit. This cause the test to hang
the system. It is found that the PTE can't transit from an
inaccessible page (b00) to a valid page (b11) because the mask
does not allow it. This happens when a big block of mmaped
memory is set the PROT_NONE, then the a small piece is broken
off and set to PROT_WRITE | PROT_READ cause a huge page split.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The functions __cpu_flush_user_tlb_range and __cpu_flush_kern_tlb_range
were removed in commit fa48e6f780 'arm64: mm: Optimise tlb flush logic
where we have >4K granule'. Global variable cpu_tlb was never used in
arm64.
Remove them.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
An arm64 allmodconfig fails to build with GCC 5 due to __asmeq
assertions in the PSCI firmware calling code firing due to mcount
preambles breaking our assumptions about register allocation of function
arguments:
/tmp/ccDqJsJ6.s: Assembler messages:
/tmp/ccDqJsJ6.s:60: Error: .err encountered
/tmp/ccDqJsJ6.s:61: Error: .err encountered
/tmp/ccDqJsJ6.s:62: Error: .err encountered
/tmp/ccDqJsJ6.s:99: Error: .err encountered
/tmp/ccDqJsJ6.s:100: Error: .err encountered
/tmp/ccDqJsJ6.s:101: Error: .err encountered
This patch fixes the issue by moving the PSCI calls out-of-line into
their own assembly files, which are safe from the compiler's meddling
fingers.
Reported-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The vdso implementation of clock_getres currently returns 0 (success)
whenever a null timespec is provided by the caller, regardless of the
clock id supplied.
This behavior is incorrect. It should fall back to syscall when an
unrecognized clock id is passed, even when the timespec argument is
null. This ensures that clock_getres always returns an error for
invalid clock ids.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Enable support for shmobile platforms that became multi-platform aware.
Several non-critical drivers and subsystems are built as modules, to keep
kernel size reasonable.
Tested on:
- r8a73a4/ape6evm:
- U-Boot fails with "Error: unrecognized/unsupported machine ID",
- kexec works.
- r8a7740/armadillo:
- Hermit boot loader fails (larger image, more memory corruption),
- kexec works.
- r8a7791/koelsch,
- sh73a0/kzm9g:
- zImage+DTB from U-Boot needs CONFIG_ARM_ATAG_DTB_COMPAT=n,
- kexec works.
- am335x/boneblack.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fixed hwmod data for pcie by having the correct module mode offset.
Previously this module mode offset was part of pcie PHY which was wrong.
Now this module mode offset was moved to pcie hwmod and removed the hwmod data
for pcie phy. While at that renamed pcie_hwmod to pciess_hwmod in order
to match with the name given in TRM.
This helps to get rid of the following warning
"omap_hwmod: pcie1: _wait_target_disable failed"
[Grygorii.Strashko@linaro.org: Found the issue that actually caused
"omap_hwmod: pcie1: _wait_target_disable failed"]
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add struct lock_class_key to omap_hwmod struct and use it to set unique
lockdep class per hwmod.
This will ensure that lockdep will know that each omap_hwmod->_lock should
be treated as separate class and will not give false warning about deadlock
or other issues due to nested use of hwmods.
DRA7x's ATL hwmod is one example for this since McASP can select ATL clock
as functional clock, which will trigger nested oh->_lock usage. This will
trigger false warning from lockdep validator as it is dealing with classes
and for it all hwmod clocks are the same class.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for various omap devices. It's all dts and defconfig
changes for this set:
- Fix wrong DMA properties for dma to avoid them getting
copied wrong again before we start actually using them
- USB fixes to revert the extcon changes as the driver did not
get merged yet and cause issues
- Omap5 and dra7 fixes to boot from sata
- Fix few am437x issues for i2c and pinctrl
- Fix beaglebone for hardwared USB configuration
- Defconfig changes for NAND, SATA and TPS62362
- Fix n900 i2c numbering for legacy user space and smc91x
register offset so it works also for qemu
- Fix incomplete USB configuration for dm816x
* tag 'fixes-v4.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-bone*: usb0 is hardwired for peripheral
ARM: dts: dra7x-evm: beagle-x15: Fix USB Host
ARM: omap2plus_defconfig: Fix SATA boot
ARM: omap2plus_defconfig: Enable OMAP NAND BCH driver
ARM: dts: dra7: Correct the dma controller's property names
ARM: dts: omap5: Correct the dma controller's property names
ARM: dts: omap4: Correct the dma controller's property names
ARM: dts: omap3: Correct the dma controller's property names
ARM: dts: omap2: Correct the dma controller's property names
ARM: dts: am437x-idk: fix sleep pinctrl state
ARM: omap2plus_defconfig: enable TPS62362 regulator
ARM: dts: am437x-idk: fix TPS62362 i2c bus
ARM: dts: n900: Fix offset for smc91x ethernet
ARM: dts: n900: fix i2c bus numbering
ARM: dts: Fix USB dts configuration for dm816x
ARM: dts: OMAP5: Fix SATA PHY node
ARM: dts: DRA7: Fix SATA PHY node
|
|
Commit 5d425c18653731af6 ("arm64: kernel: add support for cpu cache
information") adds cacheinfo support for ARM64. Since there's no
architectural way of detecting the cpus that share particular cache,
device tree can be used and the core cacheinfo already supports the
same.
This patch adds the L2 cache topology on Juno board, FVP/RTSM and
foundation models.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clockevents driver fixes from Daniel Lezcano:
- Fix the Kconfig to prevent the asm9260 timer to be compiled with
allyesconfig with sparc/sparc64 (Daniel Lezcano)
- Reorder the mtk driver init sequence in order to prevent a potential race
when the clock is registered before the irq handler is set (Matthias Brugger)
- Fix a section mismatch for the pxa driver (Robert Jarzmik)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The Kconfig options for the asm9260 timer is wrong as it can be selected by
another platform with allyes config and thus leading to a compilation failure
as some non arch related code is pulled by the compilation.
Fix this by having the platform Kconfig to select the timer as it is done for
the others drivers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Conflicts:
drivers/clocksource/Kconfig
|
|
Fixes: http://bugs.elinux.org/issues/127
the bb.org community was seeing random reboots before this change.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In commit 87517d26d888 ("ARM: dts: dra7-evm: Add extcon nodes for USB")
we enabled Extcon USB gpio to tackle the USB ID pin and get
peripheral mode to work.
But the extcon-gpio-usb driver [1] didn't make it into v4.0
and this makes the USB driver defer probe indefinitely breaking
USB Host functionality.
As a temporary fix we remove the extcon handle from the
USB controller and add it back when the extcon driver
merges in v4.1.
[1] - https://lkml.org/lkml/2015/2/2/187
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
SATA operation depends on PIPE3 PHY and if we want
to boot from SATA drives, we have to have the PIPE3 PHY
driver built-in.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Without this NAND doesn't work on most EVMs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
