| Age | Commit message (Collapse) | Author |
|---|
|
For Hummingbird PCI controllers, we should create the root
PCI memory space resource as the full 4GB area, and then
allocate the IOMMU DMA translation window out of there.
The old code just assumed that the IOMMU DMA translation base
to the top of the 4GB area was unusable. This is not true on
many systems such as SB100 and SB150, where the IOMMU DMA
translation window sits at 0xc0000000->0xdfffffff.
So what would happen is that any device mapped by the firmware
at the top section 0xe0000000->0xffffffff would get remapped
by Linux somewhere else leading to all kinds of problems and
boot failures.
While we're here, report more cases of OBP resource assignment
conflicts. The only truly valid ones are ROM resource conflicts.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do IRQ determination generically by parsing the PROM properties,
and using IRQ controller drivers for final resolution.
One immediate positive effect is that all of the IRQ frobbing
in the EBUS, ISA, and PCI controller layers has been eliminated.
We just look up the of_device and use the properly computed
value.
The PCI controller irq_build() routines are gone and no longer
used. Unfortunately sbus_build_irq() has to remain as there is
a direct reference to this in the sunzilog driver. That can be
killed off once the sparc32 side of this is written and the
sunzilog driver is transformed into an "of" bus driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One thing this change pointed out was that we really should
pull the "get 'local-mac-address' property" logic into a helper
function all the network drivers can call.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow them to be enabled with "pci=irq_verbose" on the
boot command line.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It can be pushed even further down, but this is a first step.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
this patch converts arch/sparc64 to kzalloc usage.
Crosscompile tested with allyesconfig.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the top-level cnode had multi entries in it's "reg"
property, we'd fail. The buffer wasn't large enough in
such cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The whole algorithm was wrong. What we need to do is:
1) Walk each PCI bus above this device on the path to the
PCI controller nexus, and for each:
a) If interrupt-map exists, apply it, record IRQ controller node
b) Else, swivel interrupt number using PCI_SLOT(), use PCI bus
parent OBP node as controller node
c) Walk up to "controller node" until we hit the first PCI bus
in this domain, or "controller node" is the PCI controller
OBP node
2) If we walked to PCI controller OBP node, we're done.
3) Else, apply PCI controller interrupt-map to interrupt.
There is some stuff that needs to be checked out for ebus and
isa, but the PCI part is good to go.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When crawling up the PCI bus chain, stop at the first node
that has an interrupt-map property before we hit the root.
Also, if we use a bus interrupt-{map,mask} do not forget to
update the 'intmask' pointer as we do for the 'intmap' pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
