| Age | Commit message (Collapse) | Author |
|---|
|
The MPC8541/8548/8555 Configurable Development System (CDS) were the
vehicle used to provide evaluation of the 1st e500-v2 CPUs around 2007.
Similar to the earlier MPC83xx-MDS systems we removed, the "brains"
exist on a PCI-X card, but additional connectors exist to the right of
the PCI-X slot, two structural metal pins are used to provide stability
in a vertical ATX mounting, and the CPU is now on a daughter-card vs. a
clamped down BGA.
Given the extra complexity and risk of connector damage, the 8548CDS
I had access to came pre-assembled in a basic white Antec case common
for that era, and I'm inclined to assume that was the default.
Power was typical "Pentium4" 2005 ATX - the main 20 pin connector went
to the PCI ATX form factor backplane, and the 4 pin black/yellow went
to the CPU card.
Like previous evaluation boards, they attempted to provide break-out
connectors for as many features as possible, and that made for a fairly
complex looking system.
In any case, these are over 15 years old, and fairly complex systems,
originally made for a small group of industry related people, and made
for use where quiet fan operation wasn't important. Given that, it
makes sense to remove support from them in 2023.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230620043300.197546-3-paul.gortmaker@windriver.com
|
|
Based on the revision history in the manual(s), these e500-v1
platforms were first available around 2002.
Like a lot of evaluation boards, they attempted to provide break-out
connectors for all possible features, and that combined with four
PCI-X slots (and the age/era) meant for a considerably large board.
As I recall it, from a Linux point of view, the biggest difference
between 8540 and 8560 was in the UART implementation, and that is
reflected in a diff of the defconfigs.
In any case, these are over 20 years old, and by today's standards
only have a small amount of DDR1 memory, and were not widely available.
Given that, it makes sense to remove support from them in 2023.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230620043300.197546-2-paul.gortmaker@windriver.com
|
|
There is no denying that this was an interesting platform in its day.
Access to a SMP powerpc platform became a bit more obtainable for folks
in the BSP industry in the 2007 era, thanks to this platform.
Add to that the move to the black Antec case vs. the generic white 2005
era case of the MPC8548CDS or the retro 1950s 1/2 height horizontal case
of the HPC II, and it was pretty interesting to people like myself then.
However, like all the other evaluation platforms, the overall system
was complex out of necessity, as it tried to showcase all possible
features and use-cases. That included an AMP option, where you could run
two bootloaders and two kernels over two serial consoles. Peripheral
sharing got a bit more tricky when you got to the hard disk and similar.
In any case we still have the same circumstance. A relatively rare and
expensive evaluation platform that is now 15+ years old and not out there
in large numbers in the general public. Removal in 2023 just makes sense.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230225201318.3682-3-paul.gortmaker@windriver.com
|
|
Since commit eca70102cfb1 ("net: dsa: felix: add support for changing
DSA master") included in kernel v6.1, the driver supports 2 CPU ports,
and they can be put in a LAG, for example (see
Documentation/networking/dsa/configuration.rst for more details).
Defining the second CPU port in the device tree should not cause any
compatibility issue, because the default CPU port was &seville_port8
before this change, and still is &seville_port8 now (the numerically
first CPU port is used by default).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It looks like U-Boot fails to start the kernel properly when the
compatible string of the board isn't fsl,T1040RDB, so stop overriding it
from the rev-a.dts.
Fixes: 5ebb74749202 ("powerpc: dts: t1040rdb: fix ports names for Seville Ethernet switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There aren't enough resources to run these ports at 10G speeds. Disable
10G for these ports, reverting to the previous speed.
Fixes: 36926a7d70c2 ("powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G")
Reported-by: Camelia Alexandra Groza <camelia.groza@nxp.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Link: https://lore.kernel.org/r/20221216172937.2960054-1-sean.anderson@seco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add powerpc qspinlock implementation optimised for large system
scalability and paravirt. See the merge message for more details
- Enable objtool to be built on powerpc to generate mcount locations
- Use a temporary mm for code patching with the Radix MMU, so the
writable mapping is restricted to the patching CPU
- Add an option to build the 64-bit big-endian kernel with the ELFv2
ABI
- Sanitise user registers on interrupt entry on 64-bit Book3S
- Many other small features and fixes
Thanks to Aboorva Devarajan, Angel Iglesias, Benjamin Gray, Bjorn
Helgaas, Bo Liu, Chen Lifu, Christoph Hellwig, Christophe JAILLET,
Christophe Leroy, Christopher M. Riedl, Colin Ian King, Deming Wang,
Disha Goel, Dmitry Torokhov, Finn Thain, Geert Uytterhoeven, Gustavo A.
R. Silva, Haowen Bai, Joel Stanley, Jordan Niethe, Julia Lawall, Kajol
Jain, Laurent Dufour, Li zeming, Miaoqian Lin, Michael Jeanson, Nathan
Lynch, Naveen N. Rao, Nayna Jain, Nicholas Miehlbradt, Nicholas Piggin,
Pali Rohár, Randy Dunlap, Rohan McLure, Russell Currey, Sathvika
Vasireddy, Shaomin Deng, Stephen Kitt, Stephen Rothwell, Thomas
Weißschuh, Tiezhu Yang, Uwe Kleine-König, Xie Shaowen, Xiu Jianfeng,
XueBing Chen, Yang Yingliang, Zhang Jiaming, ruanjinjie, Jessica Yu,
and Wolfram Sang.
* tag 'powerpc-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (181 commits)
powerpc/code-patching: Fix oops with DEBUG_VM enabled
powerpc/qspinlock: Fix 32-bit build
powerpc/prom: Fix 32-bit build
powerpc/rtas: mandate RTAS syscall filtering
powerpc/rtas: define pr_fmt and convert printk call sites
powerpc/rtas: clean up includes
powerpc/rtas: clean up rtas_error_log_max initialization
powerpc/pseries/eeh: use correct API for error log size
powerpc/rtas: avoid scheduling in rtas_os_term()
powerpc/rtas: avoid device tree lookups in rtas_os_term()
powerpc/rtasd: use correct OF API for event scan rate
powerpc/rtas: document rtas_call()
powerpc/pseries: unregister VPA when hot unplugging a CPU
powerpc/pseries: reset the RCU watchdogs after a LPM
powerpc: Take in account addition CPU node when building kexec FDT
powerpc: export the CPU node count
powerpc/cpuidle: Set CPUIDLE_FLAG_POLLING for snooze state
powerpc/dts/fsl: Fix pca954x i2c-mux node names
cxl: Remove unnecessary cxl_pci_window_alignment()
selftests/powerpc: Fix resource leaks
...
|
|
"make dtbs_check":
arch/powerpc/boot/dts/fsl/t1040rdb-rev-a.dtb: pca9546@77: $nodename:0: 'pca9546@77' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arch/powerpc/boot/dts/fsl/t1024qds.dtb: pca9547@77: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@2', 'i2c@3' were unexpected)
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming pca954x nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/6c5d86c49ac170e9d56ab121ea0602f3873849ca.1669999298.git.geert+renesas@glider.be
|
|
Now that we actually read registers from QSGMII PCSs, it's important
that we have the correct address (instead of hoping that we're the MAC
with all the QSGMII PCSs on its bus). This adds nodes for the QSGMII
PCSs. They have the same addresses on all SoCs (e.g. if QSGMIIA is
present it's used for MACs 1 through 4).
Since the first QSGMII PCSs share an address with the SGMII and XFI
PCSs, we only add new nodes for PCSs 2-4. This avoids address conflicts
on the bus.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the T208X SoCs, MAC1 and MAC2 support XGMII. Add some new MAC dtsi
fragments, and mark the QMAN ports as 10G.
Fixes: da414bb923d9 ("powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2eb28006431c ("powerpc/e500v2: Add Power ISA properties to comply
with ePAPR 1.1") introduced new include file e500v2_power_isa.dtsi and
should have used it for all e500v2 platforms. But apparently it was used
also for e500v1 platforms mpc8540, mpc8541, mpc8555 and mpc8560.
e500v1 cores compared to e500v2 do not support double precision floating
point SPE instructions. Hence power-isa-sp.fd should not be set on e500v1
platforms, which is in e500v2_power_isa.dtsi include file.
Fix this issue by introducing a new e500v1_power_isa.dtsi include file and
use it in all e500v1 device tree files.
Fixes: 2eb28006431c ("powerpc/e500v2: Add Power ISA properties to comply with ePAPR 1.1")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220902212103.22534-1-pali@kernel.org
|
|
DT law_trgt_if property defines Local Access Window Target Interface.
Local Access Window Target Interface is used for identifying individual
peripheral and mapping its memory to CPU. Interface id is defined by
hardware itself.
U-Boot uses law_trgt_if DT property in PCIe nodes for configuring memory
mapping of individual PCIe controllers.
Linux kernel fsl_pci.c driver currently does not touch Local Access Window
and expects that U-Boot configures it properly.
Add law_trgt_if property to PCIe DT nodes for P2020. This allows usage of
kernel P2020 PCIe DT nodes in U-Boot. And therefore allows to share P2020
DTS files between Linux kernel and U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220504180822.29782-1-pali@kernel.org
|
|
P2020 also contains Power Management Controller and their registers at
offset 0xe0070 compatible with mpc8548. So add PMC node into DTS include
file fsl/p2020si-post.dtsi
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220506203621.26314-1-pali@kernel.org
|
|
On board rev A, the network interface labels for the switch ports
written on the front panel are different than on rev B and later.
This patch fixes network interface names for the switch ports according
to labels that are written on the front panel of the board rev B.
They start from ETH3 and end at ETH10.
This patch also introduces a separate device tree for rev A.
The main device tree is supposed to cover rev B and later.
Fixes: e69eb0824d8c ("powerpc: dts: t1040rdb: add ports for Seville Ethernet switch")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220121091447.3412907-1-bigunclemax@gmail.com
|
|
T1040RDB has two RTL8211E-VB phys which requires setting
of internal delays for correct work.
Changing the phy-connection-type property to `rgmii-id`
will fix this issue.
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211230151123.1258321-1-bigunclemax@gmail.com
|
|
This block is used in (at least) T1024 and T1040, including their
variants like T1023 etc.
Fixes: d55ad2967d89 ("powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Property phy-connection-type contains invalid value "sgmii-2500" per scheme
defined in file ethernet-controller.yaml.
Correct phy-connection-type value should be "2500base-x".
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 84e0f1c13806 ("powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)")
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The support was for this was added to mainline over 12 years ago, in
v2.6.26 [4e8aae89a35d] just around the ppc --> powerpc migration.
I believe the board was introduced shortly after the sbc8548 board,
making it roughly a 14 year old platform - with the CPU speed and
memory size typical for that era.
I haven't had one of these boards for several years, and availability
was discontinued several years before that.
Given that, there is no point in adding a burden to testing coverage
that builds all possible defconfigs, so it makes sense to remove it.
Of course it will remain in the git history forever, for anyone who
happens to find a functional board and wants to tinker with it.
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The i2c controllers on the P1010 have an erratum where the documented
scheme for i2c bus recovery will not work (A-004447). A different
mechanism is needed which is documented in the P1010 Chip Errata Rev L.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The i2c controllers on the P2040/P2041 have an erratum where the
documented scheme for i2c bus recovery will not work (A-004447). A
different mechanism is needed which is documented in the P2040 Chip
Errata Rev Q (latest available at the time of writing).
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
These are very old properties that were used by the "gianfar" ethernet
driver. They don't have documented bindings and are obsolete.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- A series from Nick adding ARCH_WANT_IRQS_OFF_ACTIVATE_MM & selecting
it for powerpc, as well as a related fix for sparc.
- Remove support for PowerPC 601.
- Some fixes for watchpoints & addition of a new ptrace flag for
detecting ISA v3.1 (Power10) watchpoint features.
- A fix for kernels using 4K pages and the hash MMU on bare metal
Power9 systems with > 16TB of RAM, or RAM on the 2nd node.
- A basic idle driver for shallow stop states on Power10.
- Tweaks to our sched domains code to better inform the scheduler about
the hardware topology on Power9/10, where two SMT4 cores can be
presented by firmware as an SMT8 core.
- A series doing further reworks & cleanups of our EEH code.
- Addition of a filter for RTAS (firmware) calls done via sys_rtas(),
to prevent root from overwriting kernel memory.
- Other smaller features, fixes & cleanups.
Thanks to: Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Athira Rajeev, Biwen Li, Cameron Berkenpas, Cédric Le Goater, Christophe
Leroy, Christoph Hellwig, Colin Ian King, Daniel Axtens, David Dai, Finn
Thain, Frederic Barrat, Gautham R. Shenoy, Greg Kurz, Gustavo Romero,
Ira Weiny, Jason Yan, Joel Stanley, Jordan Niethe, Kajol Jain, Konrad
Rzeszutek Wilk, Laurent Dufour, Leonardo Bras, Liu Shixin, Luca
Ceresoli, Madhavan Srinivasan, Mahesh Salgaonkar, Nathan Lynch, Nicholas
Mc Guire, Nicholas Piggin, Nick Desaulniers, Oliver O'Halloran, Pedro
Miraglia Franco de Carvalho, Pratik Rajesh Sampat, Qian Cai, Qinglang
Miao, Ravi Bangoria, Russell Currey, Satheesh Rajendran, Scott Cheloha,
Segher Boessenkool, Srikar Dronamraju, Stan Johnson, Stephen Kitt,
Stephen Rothwell, Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain,
Vaidyanathan Srinivasan, Vasant Hegde, Wang Wensheng, Wolfram Sang, Yang
Yingliang, zhengbin.
* tag 'powerpc-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (228 commits)
Revert "powerpc/pci: unmap legacy INTx interrupts when a PHB is removed"
selftests/powerpc: Fix eeh-basic.sh exit codes
cpufreq: powernv: Fix frame-size-overflow in powernv_cpufreq_reboot_notifier
powerpc/time: Make get_tb() common to PPC32 and PPC64
powerpc/time: Make get_tbl() common to PPC32 and PPC64
powerpc/time: Remove get_tbu()
powerpc/time: Avoid using get_tbl() and get_tbu() internally
powerpc/time: Make mftb() common to PPC32 and PPC64
powerpc/time: Rename mftbl() to mftb()
powerpc/32s: Remove #ifdef CONFIG_PPC_BOOK3S_32 in head_book3s_32.S
powerpc/32s: Rename head_32.S to head_book3s_32.S
powerpc/32s: Setup the early hash table at all time.
powerpc/time: Remove ifdef in get_dec() and set_dec()
powerpc: Remove get_tb_or_rtc()
powerpc: Remove __USE_RTC()
powerpc: Tidy up a bit after removal of PowerPC 601.
powerpc: Remove support for PowerPC 601
powerpc: Remove PowerPC 601
powerpc: Drop SYNC_601() ISYNC_601() and SYNC()
powerpc: Remove CONFIG_PPC601_SYNC_FIX
...
|
|
Define the network interface names for the switch ports and hook them up
to the 2 QSGMII PHYs that are onboard.
A conscious decision was taken to go along with the numbers that are
written on the front panel of the board and not with the hardware
numbers of the switch chip ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the description of the embedded L2 switch inside the SoC dtsi file
for NXP T1040.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the interrupt pin for RTC DS1339 is not connected
to the CPU on T1024RDB, remove the interrupt property
from the device tree.
This also fix the following warning for hwclock.util-linux:
$ hwclock.util-linux
hwclock.util-linux: select() to /dev/rtc0
to wait for clock tick timed out
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200527034228.23793-2-biwen.li@oss.nxp.com
|
|
Since the interrupt pin for RTC DS1374 is not connected
to the CPU on T4240RDB, remove the interrupt property
from the device tree.
This also fix the following warning for hwclock.util-linux:
$ hwclock.util-linux
hwclock.util-linux: select() to /dev/rtc0
to wait for clock tick timed out
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200527034228.23793-1-biwen.li@oss.nxp.com
|
|
This just adds the zl2006 voltage regulators / power monitors and the
onboard I2C eeproms. The ICS9FG108 clock chip doesn't seem to have a
driver, so it is left in the DTS as a comment. And for good measure,
the SPD eeproms are tagged as such.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20180920230422.GK487685@eidolon.nox.tf
|
|
Add fsl,erratum-a011043 to internal MDIO buses.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes the warnings about the fact that the 4 pci bridges (i.e.
the 4 pci hosts) don't have any ranges.
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
Change all phy-connection-type properties to phy-mode that are better
supported by the fman driver.
Use the more readable fixed-link node for the 2 sgmii links.
Change the RGMII link to rgmii-id as the clock delays are added by the
phy.
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
crypto node alias is needed by U-boot to identify the node and
perform fix-ups, like adding "fsl,sec-era" property.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
mpc8641_hpcn was updated to 4-cell interrupt specifiers, but
PCI interrupt-map was not updated. It was also missing #interrupt-cells
on the outer PCI buses.
p1020rdb-pc was updated to 4-cell interrupt specifiers, but
the ethernet-phy nodes weren't updated.
mpc832x_rdb had an invalid "interrupts = <0>" on the ethernet-phy nodes.
Besides being the wrong number of cells, 0 is not a valid IPIC interrupt
according to ipic.c. Presumably it was meant to indicate that these
PHYs are not connected to an interrupt.
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
The driver retains compatibility with old device trees, but we don't
want the old nodes lying around to be copied, or used as a reference
(some of the mux options are incorrect), or even just being clutter.
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
[scottwood: removed sysclk node added by Andy]
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some things that I missed due to travel, or that came in late.
Two fixes also going to stable:
- A revert of a buggy change to the 8xx TLB miss handlers.
- Our flushing of SPE (Signal Processing Engine) registers on fork
was broken.
Other changes:
- A change to the KVM decrementer emulation to use proper APIs.
- Some cleanups to the way we do code patching in the 8xx code.
- Expose the maximum possible memory for the system in
/proc/powerpc/lparcfg.
- Merge some updates from Scott: "a couple device tree updates, and a
fix for a missing prototype warning"
A few other minor fixes and a handful of fixes for our selftests.
Thanks to: Aravinda Prasad, Breno Leitao, Camelia Groza, Christophe
Leroy, Felipe Rechia, Joel Stanley, Naveen N. Rao, Paul Mackerras,
Scott Wood, Tyrel Datwyler"
* tag 'powerpc-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (21 commits)
selftests/powerpc: Fix compilation issue due to asm label
selftests/powerpc/cache_shape: Fix out-of-tree build
selftests/powerpc/switch_endian: Fix out-of-tree build
selftests/powerpc/pmu: Link ebb tests with -no-pie
selftests/powerpc/signal: Fix out-of-tree build
selftests/powerpc/ptrace: Fix out-of-tree build
powerpc/xmon: Relax frame size for clang
selftests: powerpc: Fix warning for security subdir
selftests/powerpc: Relax L1d miss targets for rfi_flush test
powerpc/process: Fix flush_all_to_thread for SPE
powerpc/pseries: add missing cpumask.h include file
selftests/powerpc: Fix ptrace tm failure
KVM: PPC: Use exported tb_to_ns() function in decrementer emulation
powerpc/pseries: Export maximum memory value
powerpc/8xx: Use patch_site for perf counters setup
powerpc/8xx: Use patch_site for memory setup patching
powerpc/code-patching: Add a helper to get the address of a patch_site
Revert "powerpc/8xx: Use L1 entry APG to handle _PAGE_ACCESSED for CONFIG_SWAP"
powerpc/8xx: add missing header in 8xx_mmu.c
powerpc/8xx: Add DT node for using the SEC engine of the MPC885
...
|
|
According to the T2080RDB schematics, for the CS4315 PHY, the XFI 1 lane is
connected to SFP 2 and the XFI 2 lane is connected to SFP 1. Change the
device tree to reflect the correct PHY order and port association.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
Enable the 'dtbs' target for powerpc. This allows building all the dts
files in arch/powerpc/boot/dts/ when COMPILE_TEST and OF_ALL_DTBS are
enabled.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A fix for a bug in our page table fragment allocator, where a page
table page could be freed and reallocated for something else while
still in use, leading to memory corruption etc. The fix reuses
pt_mm in struct page (x86 only) for a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but
bring us in to line with x86 behaviour and/or fix outright bugs.
Thanks to Florian Weimer for reporting many of these.
- A series to improve the hvc driver & related OPAL console code,
which have been seen to cause hardlockups at times. The hvc driver
changes in particular have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
use anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX
instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM
CPUs (controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals
to bring it into line with other arches, including showing the
offending VMA and dumping the instructions around the fault.
Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
Rao, zhong jiang"
* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
powerpc/mm/book3s/radix: Add mapping statistics
powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
powerpc/mm/hash: Remove unnecessary do { } while(0) loop
powerpc/64s: move machine check SLB flushing to mm/slb.c
powerpc/powernv/idle: Fix build error
powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
powerpc/mm: remove warning about ‘type’ being set
powerpc/32: Include setup.h header file to fix warnings
powerpc: Move `path` variable inside DEBUG_PROM
powerpc/powermac: Make some functions static
powerpc/powermac: Remove variable x that's never read
cxl: remove a dead branch
powerpc/powermac: Add missing include of header pmac.h
powerpc/kexec: Use common error handling code in setup_new_fdt()
powerpc/xmon: Add address lookup for percpu symbols
powerpc/mm: remove huge_pte_offset_and_shift() prototype
powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
powerpc/fadump: handle crash memory ranges array index overflow
...
|
|
The Cortina PHY is not compatible with IEEE 802.3 clause 45.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[scottwood: made commit message about compatibility, not driver choice]
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
The Cortina PHY is not compatible with IEEE 802.3 clause 45.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[scottwood: made commit message about compatibility, not driver choice]
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
This patch is to add clocks property for fman ptp timer node.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch is to move ptp timer node out of fman.
Because ptp timer will be probed by ptp_qoriq driver,
it should be an independent device in case of conflict
memory mapping.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sanctioned compatible is "nxp,pca9547".
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace all the of occurrences with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9
when using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts
as well as "normal" interrupts, and then use that to implement
local_t for a ~4x speedup vs the current atomics-based
implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor
Interface (OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe
hotpluggable memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit
VDSO.
- Freescale updates from Scott: fixes for CPM GPIO and an FSL PCI
erratum workaround, plus a minor cleanup patch.
As well as quite a lot of other changes all over the place, and small
fixes and cleanups as always.
Thanks to: Alan Modra, Alastair D'Silva, Alexey Kardashevskiy,
Alistair Popple, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
Anju T Sudhakar, Anshuman Khandual, Anton Blanchard, Arnd Bergmann,
Balbir Singh, Benjamin Herrenschmidt, Bhaktipriya Shridhar, Bryant G.
Ly, Cédric Le Goater, Christophe Leroy, Christophe Lombard, Cyril Bur,
David Gibson, Desnes A. Nunes do Rosario, Dmitry Torokhov, Frederic
Barrat, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo A. R. Silva,
Gustavo Romero, Ivan Mikhaylov, Joakim Tjernlund, Joe Perches, Josh
Poimboeuf, Juan J. Alvarez, Julia Cartwright, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud,
Ram Pai, Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee,
Simon Guo, Stewart Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann,
Vaibhav Jain, Vasyl Gomonovych"
* tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (199 commits)
powerpc/mm/radix: Fix build error when RADIX_MMU=n
macintosh/ams-input: Use true and false for boolean values
macintosh: change some data types from int to bool
powerpc/watchdog: Print the NIP in soft_nmi_interrupt()
powerpc/watchdog: regs can't be null in soft_nmi_interrupt()
powerpc/watchdog: Tweak watchdog printks
powerpc/cell: Remove axonram driver
rtc-opal: Fix handling of firmware error codes, prevent busy loops
powerpc/mpc52xx_gpt: make use of raw_spinlock variants
macintosh/adb: Properly mark continued kernel messages
powerpc/pseries: Fix cpu hotplug crash with memoryless nodes
powerpc/numa: Ensure nodes initialized for hotplug
powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
powerpc/kernel: Block interrupts when updating TIDR
powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn
powerpc/mm/nohash: do not flush the entire mm when range is a single page
powerpc/pseries: Add Initialization of VF Bars
powerpc/pseries/pci: Associate PEs to VFs in configure SR-IOV
powerpc/eeh: Add EEH notify resume sysfs
powerpc/eeh: Add EEH operations to notify resume
...
|
|
Improve the DTS files by removing all the leading "0x" and zeros to
fix the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and:
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were
resolved, namely setting unit-address to lower case, and adding a
whitespace before the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove
leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The flexcan driver assumed that flexcan controller is big endian for
powerpc architecture and little endian for other architectures.
But this is not universally true. flexcan controller can be little or
big endian on any architecture.
Therefore the flexcan driver has been modified to check for "big-endian"
device tree property for controllers that are big endian.
consequently add the property to freescale P1010 SOC device tree.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for STRICT_KERNEL_RWX on 64-bit server CPUs.
- Platform support for FSP2 (476fpe) board
- Enable ZONE_DEVICE on 64-bit server CPUs.
- Generic & powerpc spin loop primitives to optimise busy waiting
- Convert VDSO update function to use new update_vsyscall() interface
- Optimisations to hypercall/syscall/context-switch paths
- Improvements to the CPU idle code on Power8 and Power9.
As well as many other fixes and improvements.
Thanks to: Akshay Adiga, Andrew Donnellan, Andrew Jeffery, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Benjamin Herrenschmidt,
Christophe Leroy, Christophe Lombard, Colin Ian King, Dan Carpenter,
Gautham R. Shenoy, Hari Bathini, Ian Munsie, Ivan Mikhaylov, Javier
Martinez Canillas, Madhavan Srinivasan, Masahiro Yamada, Matt Brown,
Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Naveen N.
Rao, Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pavel Machek,
Russell Currey, Santosh Sivaraj, Stephen Rothwell, Thiago Jung
Bauermann, Yang Li"
* tag 'powerpc-4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (158 commits)
powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs
powerpc/mm/radix: Implement STRICT_RWX/mark_rodata_ro() for Radix
powerpc/mm/hash: Implement mark_rodata_ro() for hash
powerpc/vmlinux.lds: Align __init_begin to 16M
powerpc/lib/code-patching: Use alternate map for patch_instruction()
powerpc/xmon: Add patch_instruction() support for xmon
powerpc/kprobes/optprobes: Use patch_instruction()
powerpc/kprobes: Move kprobes over to patch_instruction()
powerpc/mm/radix: Fix execute permissions for interrupt_vectors
powerpc/pseries: Fix passing of pp0 in updatepp() and updateboltedpp()
powerpc/64s: Blacklist rtas entry/exit from kprobes
powerpc/64s: Blacklist functions invoked on a trap
powerpc/64s: Un-blacklist system_call() from kprobes
powerpc/64s: Move system_call() symbol to just after setting MSR_EE
powerpc/64s: Blacklist system_call() and system_call_common() from kprobes
powerpc/64s: Convert .L__replay_interrupt_return to a local label
powerpc64/elfv1: Only dereference function descriptor for non-text symbols
cxl: Export library to support IBM XSL
powerpc/dts: Use #include "..." to include local DT
powerpc/perf/hv-24x7: Aggregate result elements on POWER9 SMT8
...
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
