| Age | Commit message (Collapse) | Author |
|---|
|
w90x900 still provides its own variant of the clk API rather than using
the generic COMMON_CLK API. This generally works, but it causes some link
errors with drivers using the clk_set_rate, clk_get_parent, clk_set_parent
or clk_round_rate functions when a platform lacks those interfaces.
This adds empty stub implementations for each of them, and I don't even
try to do something useful here but instead just print a WARN() message
to make it obvious what is going on if they ever end up being called.
The drivers that call these won't be used on these platforms (otherwise
we'd get a link error today), so the added code is harmless bloat and
will warn about accidental use.
A while ago there was a proposal to change w90x900 to use the common-clk
implementation, which would be the way it should be handled properly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
It's a combination of the patch from Arnd Bergmann, which added empty stubs
for clk_round_rate() and clk_set_parent() and a working trivial
implementation of clk_get_parent(). The later is required for ADC driver.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull ARM fixes from Russell King:
"Two areas addressed by these fixes:
- Fixes from Dave Martin for the signal frames that were broken with
certain configurations. No one noticed until recently.
- More kexec fixes to ensure that the crashkernel region is correctly
allocated, and a fix for the location of the device tree when
several kexec kernels are loaded"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8687/1: signal: Fix unparseable iwmmxt_sigframe in uc_regspace[]
ARM: 8686/1: iwmmxt: Add missing __user annotations to sigframe accessors
ARM: kexec: fix failure to boot crash kernel
ARM: kexec: avoid allocating crashkernel region outside lowmem
|
|
Define the iwg20m board dependent part of the MMCIF0 device node.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use R-Car Gen 2 fallback binding for vind nodes in DT for r8a7794 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7794 and the
fallback binding for R-Car Gen 2
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Use R-Car Gen 2 fallback binding for vind nodes in DT for r8a7791 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7791 and the
fallback binding for R-Car Gen 2
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Use R-Car Gen 2 fallback binding for vind nodes in DT for r8a7790 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7790 and the
fallback binding for R-Car Gen 2
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The migration from ARCH_SHMOBILE_MULTI to ARCH_RENESAS has been
completed in v4.12 by commit 9ed2d4bc5c0c244d ("ARM: dts: renesas:
Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS"), so the
ARCH_SHMOBILE_MULTI symbol can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to the datasheet, the frequency of the ARM architecture timer
on RZ/G1E depends on the frequency of the ZS clock, just like on R-Car
E2 and V2H.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
When using the new CPG/MSSR bindings, there is no longer a
"renesas,rcar-gen2-cpg-clocks" node, and the code to obtain the external
clock crystal frequency falls back to a default of 20 MHz.
While this is correct for all upstream R-Car Gen2 and RZ/G1 boards, this
is not necessarily the case for out-of-tree third party boards.
Add support for finding the external clock crystal oscillator on RZ/G1M,
and on R-Car H2, M2-W, and M2-N using the new CPG/MSSR bindings, through
the corresponding "renesas,r8a77xx-cpg-mssr" nodes.
Note that this is not needed on R-Car V2H and E2, and on RZ/G1E, as on
those SoCs the arch_timer and generic counter clock is derived from the
ZS clock instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for obtaining from DT the SRAM region to store the jump stub
for CPU core bringup, according to the renesas,smp-sram DT bindings.
If no region is specified in DT, the code falls back to hardcoded ICRAM1
as before, to maintain backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable low-level debugging support for RZ/G1M (r8a7743). RZ/G1M uses
SCIF0 for the debug console, like most of the R-Car Gen2 SoCs.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the MMCIF0 device to the r8a7743 device tree.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
R-Car E2 has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
R-Car M2-N has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
R-Car V2H has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
R-Car M2-W has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
R-Car H2 has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
RZ/G1E has 3 regions of Inter Connect RAM (72 + 4 + 256 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
RZ/G1M has 3 regions of Inter Connect RAM (72 + 4 + 256 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the iWave RainboW-G20D-Qseven board dependent part of the Ethernet
AVB device node.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add Ethernet AVB support for r8a7743 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Adding pinctrl support for scif0 interface.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Describe GPIO blocks in the R8A7743 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the (previously omitted) Ether/PHY pin data to the SK-RZG1M board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the (previously omitted) SCIF0 pin data to the SK-RZG1M board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the generic R8A7743 part of the PFC device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
DMA for (H)SCIF(A|B) serial ports on Renesas R-Car Gen2 and RZ/G1 SoCs
is considered stable, hence enable it by default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The manual bridge implementation was removed in favor of the generic
one, so now we need to enable standard bridge drivers like
DRM_DUMB_VGA_DAC and DRM_I2C_ADV7511.
Both were already enabled, but the (newer) ADV7511 audio part wasn't.
Fixes: 5c602531feb3db39 ("drm: rcar-du: Replace manual bridge implementation with DRM bridge")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
SND_SOC_RSRC_CARD was renamed SND_SIMPLE_SCU_CARD, hence update
multi_v7_defconfig.
Fixes: d12c6216c4a58f9f ("ASoC: rsrc-card: rename rsrc-card to simple-scu-card phase3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
- Several options were moved,
- INPUT_MOUSEDEV_PSAUX is no longer enabled by default since commit
73d8ef76006b649f ("Input: mousedev - stop offering PS/2 to userspace
by default").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
DMA for (H)SCIF(A|B) serial ports on R-Car Gen2 and RZ/G1 SoCs is
considered stable, hence enable it by default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The manual bridge implementation was removed in favor of the generic
one, so now we need to enable standard bridge drivers like
DRM_DUMB_VGA_DAC and DRM_I2C_ADV7511.
DRM_I2C_ADV7511 was already enabled, but the (newer) audio part wasn't.
Fixes: 5c602531feb3db39 ("drm: rcar-du: Replace manual bridge implementation with DRM bridge")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
SND_SOC_RSRC_CARD was renamed SND_SIMPLE_SCU_CARD, hence update
shmobile_defconfig.
Fixes: d12c6216c4a58f9f ("ASoC: rsrc-card: rename rsrc-card to simple-scu-card phase3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
USB_XHCI_RCAR is no longer enabled, as it now has a dependency on
USB_XHCI_PLATFORM, instead of selecting USB_XHCI_PLATFORM.
As the latter selects the former if ARCH_RENESAS, fix this by replacing
USB_XHCI_RCAR by USB_XHCI_PLATFORM in shmobile_defconfig.
Fixes: f879fc32aa0c96fb ("usb: host: xhci-rcar: Avoid long wait in xhci_reset()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
PCIE_RCAR is no longer enabled, as it now has a dependency on
PCI_MSI_IRQ_DOMAIN instead of selecting PCI_MSI and PCI_MSI_IRQ_DOMAIN.
Fix this by explicitly enabling PCIE_RCAR in shmobile_defconfig.
Fixes: 3ee803641e76bea7 ("PCI/MSI: irqchip: Fix PCI_MSI dependencies")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The iWave RZ/G1M Q7 SOM supports Gigabit Ethernet Phy (Micrel KSZ9031MNX).
Gigabit Ethernet support is available in Renesas AVB driver.
To increase hardware support enable the driver in the shmobile_defconfig
multiplatform configuration.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Now that the CCU device tree binding headers have been merged, we can
use the properly named macros in the device tree, instead of raw
numbers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The datasheet said that emac register size is 0x10000 not 0x104
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Fixed commit subject prefix]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Since the PMU register interface is banked per CPU, CPU PMU interrrupts
cannot be handled by a CPU other than the one with the PMU asserting the
interrupt. This means that migrating PMU SPIs, as we do during a CPU
hotplug operation doesn't make any sense and can lead to the IRQ being
disabled entirely if we route a spurious IRQ to the new affinity target.
This has been observed in practice on AMD Seattle, where CPUs on the
non-boot cluster appear to take a spurious PMU IRQ when coming online,
which is routed to CPU0 where it cannot be handled.
This patch passes IRQF_PERCPU for PMU SPIs and forcefully sets their
affinity prior to requesting them, ensuring that they cannot
be migrated during hotplug events. This interacts badly with the DB8500
erratum workaround that ping-pongs the interrupt affinity from the handler,
so we avoid passing IRQF_PERCPU in that case by allowing the IRQ flags
to be overridden in the platdata.
Fixes: 3cf7ee98b848 ("drivers/perf: arm_pmu: move irq request/free into probe")
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
sa1100 provides its own variant of the clk API rather than using the
generic COMMON_CLK API. This generally works, but it causes some link
errors with drivers using the clk_set_rate, clk_get_parent, clk_set_parent
or clk_round_rate functions when a platform lacks those interfaces.
This adds trivial stub implementations for each of them, based on
the behavior of the COMMON_CLK implementation:
- set_rate() and set_parent() report success without doing anything
- round_rate() returns the clk rate
- get_parent() returns NULL.
This adds the minimal bloat and should do the right thing for
the simple clock hardware in this SoC.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
