| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 47fe74098f3dadba2f9cc1e507d813a4aa93f5f3 ]
Don't put the l4ls clk domain to sleep in case of standby.
Since CM3 PM FW[1](ti-v4.1.y) doesn't wake-up/enable the l4ls clk domain
upon wake-up, CM3 PM FW fails to wake-up the MPU.
[1] https://git.ti.com/cgit/processor-firmware/ti-amx3-cm3-pm-firmware/
Signed-off-by: Sukrut Bellary <sbellary@baylibre.com>
Tested-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250318230042.3138542-2-sbellary@baylibre.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 7397daf1029d5bfd3415ec8622f5179603d5702d upstream.
The late init call just writes to omap4 registers as soon as
CONFIG_MFD_CPCAP is enabled without checking whether the
cpcap driver is actually there or the SoC is indeed an
OMAP4.
Rather do these things only with the right device combination.
Fixes booting the BT200 with said configuration enabled and non-factory
X-Loader and probably also some surprising behavior on other devices.
Fixes: c145649bf262 ("ARM: OMAP2+: Configure voltage controller for cpcap to low-speed")
CC: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reivewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20250331144439.769697-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96e0b355883006554a0bee3697da475971d6bba8 upstream.
arm/memremap: fix arch_memremap_can_ram_remap()
commit 260364d112bc ("arm[64]/memremap: don't abuse pfn_valid() to ensure
presence of linear map") added the definition of
arch_memremap_can_ram_remap() for arm[64] specific filtering of what pages
can be used from the linear mapping. memblock_is_map_memory() was called
with the pfn of the address given to arch_memremap_can_ram_remap();
however, memblock_is_map_memory() expects to be given an address for arm,
not a pfn.
This results in calls to memremap() returning a newly mapped area when
it should return an address in the existing linear mapping.
Fix this by removing the address to pfn translation and pass the
address directly.
Fixes: 260364d112bc ("arm[64]/memremap: don't abuse pfn_valid() to ensure presence of linear map")
Signed-off-by: Ross Stutterheim <ross.stutterheim@garmin.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e4f59f873c3ffe2a0150e11115a83e2dfb671dbf ]
The ASPEED devices have SRAM, but don't require it for basic function
(or any function; there's no known users of the driver).
Fixes: 8c2ed9bcfbeb ("arm: Add Aspeed machine")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://patch.msgid.link/20250115103942.421429-1-joel@jms.id.au
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f2420037d90a8354594b3da541e19dcbb60c75e1 ]
The CoreSight static replicator device isn't a part of the system MMIO
bus, as such it should not be a part of the soc node. Follow the example
of other platforms and move it out of the soc bus to the top-level (and
reoder ports to follow alphabetic order).
Fixes: 7a5c275fd821 ("ARM: dts: qcom: Add apq8064 CoreSight components")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318-fix-nexus-4-v2-10-bcedd1406790@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 325c6a441ae1f8fcb1db9bb945b8bdbd3142141e ]
Follow up the expected way of describing the SFPB hwspinlock and merge
hwspinlock node into corresponding syscon node, fixing several dt-schema
warnings.
Fixes: 24a9baf933dc ("ARM: dts: qcom: apq8064: Add hwmutex and SMEM nodes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318-fix-nexus-4-v2-7-bcedd1406790@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b0eb149df58b6750cd8113e5ee5b3ac7cc51743 ]
In order to fix DT schema warning and describe hardware properly, add
missing sleep clock to the timer node.
Fixes: f335b8af4fd5 ("ARM: dts: qcom: Add initial APQ8064 SoC and IFC6410 board device trees")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318-fix-nexus-4-v2-6-bcedd1406790@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c72ede1c24be689733bcd2233a3a56f2478429c8 ]
NAND did not work on my USB-A9263. I discovered that the offending
commit converted the PIO bank for chip selects wrongly, so all A9263
boards need to be fixed.
Fixes: 1004a2977bdc ("ARM: dts: at91: Switch to the new NAND bindings")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20250402210446.5972-2-wsa+renesas@sang-engineering.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 67ba341e57ab158423818ed33bfa1c40eb0e5e7e ]
Dataflash did not work on my board. After checking schematics and using
the proper GPIO, it works now. Also, make it active low to avoid:
flash@0 enforce active low on GPIO handle
Fixes: 2432d201468d ("ARM: at91: dt: usb-a9263: add dataflash support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250404112742.67416-2-wsa+renesas@sang-engineering.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bc4722c3598d0e2c2dbf9609a3d3198993093e2b ]
For sama7g5 and sama7d65 backup mode, we encountered a "ZQ calibrate error"
during recalibrating the impedance in BootStrap.
We found that the impedance value saved in at91_suspend_finish() before
the DDR entered self-refresh mode did not match the resistor values. The
ZDATA field in the DDR3PHY_ZQ0CR0 register uses a modified gray code to
select the different impedance setting.
But these gray code are incorrect, a workaournd from design team fixed the
bug in the calibration logic. The ZDATA contains four independent impedance
elements, but the algorithm combined the four elements into one. The elements
were fixed using properly shifted offsets.
Signed-off-by: Li Bin <bin.li@microchip.com>
[nicolas.ferre@microchip.com: fix indentation and combine 2 patches]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Tested-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Link: https://lore.kernel.org/r/28b33f9bcd0ca60ceba032969fe054d38f2b9577.1740671156.git.Ryan.Wanner@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b3db788f2f614b875b257cdb079adadedc060f3 ]
PLLD is usually used as parent clock for internal video devices, like
DSI for example, while PLLD2 is used as parent for HDMI.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://lore.kernel.org/r/20250226105615.61087-3-clamor95@gmail.com
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e1a7bc8382b0d4208258f7d2a4474fae788dd90 ]
Commit c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific
PHY fixup") removed a PHY fixup that setted the clock mode and the LED
mode.
Make the Ethernet interface work again by doing as advised in the
commit's log, set clock mode and the LED mode in the device tree.
Fixes: c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific PHY fixup")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 17ec3e71ba797cdb62164fea9532c81b60f47167 upstream.
The ARCH_MAY_HAVE patch missed arm64, mips and s390. But it may
also lead to arch options being enabled but ineffective because
of modular/built-in conflicts.
As the primary user of all these options wireguard is selecting
the arch options anyway, make the same selections at the lib/crypto
option level and hide the arch options from the user.
Instead of selecting them centrally from lib/crypto, simply set
the default of each arch option as suggested by Eric Biggers.
Change the Crypto API generic algorithms to select the top-level
lib/crypto options instead of the generic one as otherwise there
is no way to enable the arch options (Eric Biggers). Introduce a
set of INTERNAL options to work around dependency cycles on the
CONFIG_CRYPTO symbol.
Fixes: 1047e21aecdf ("crypto: lib/Kconfig - Fix lib built-in failure when arch is modular")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Arnd Bergmann <arnd@kernel.org>
Closes: https://lore.kernel.org/oe-kbuild-all/202502232152.JC84YDLp-lkp@intel.com/
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1047e21aecdf17c8a9ab9fd4bd24c6647453f93d ]
The HAVE_ARCH Kconfig options in lib/crypto try to solve the
modular versus built-in problem, but it still fails when the
the LIB option (e.g., CRYPTO_LIB_CURVE25519) is selected externally.
Fix this by introducing a level of indirection with ARCH_MAY_HAVE
Kconfig options, these then go on to select the ARCH_HAVE options
if the ARCH Kconfig options matches that of the LIB option.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501230223.ikroNDr1-lkp@intel.com/
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e7607f7d6d81af71dcc5171278aadccc94d277cd upstream.
ld.lld prior to 21.0.0 does not support using the KEEP keyword within an
overlay description, which may be needed to avoid discarding necessary
sections within an overlay with '--gc-sections', which can be enabled
for the kernel via CONFIG_LD_DEAD_CODE_DATA_ELIMINATION.
Disallow CONFIG_LD_DEAD_CODE_DATA_ELIMINATION without support for KEEP
within OVERLAY and introduce a macro, OVERLAY_KEEP, that can be used to
conditionally add KEEP when it is properly supported to avoid breaking
old versions of ld.lld.
Cc: stable@vger.kernel.org
Link: https://github.com/llvm/llvm-project/commit/381599f1fe973afad3094e55ec99b1620dba7d8c
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[nathan: Fix conflict in init/Kconfig due to lack of RUSTC symbols]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3d944a367c0d9e4e125c7006e52f352e75776dc upstream.
Without this, the vectors are removed if LD_DEAD_CODE_DATA_ELIMINATION
is enabled. At startup, the CPU (silently) hangs in the undefined
instruction exception as soon as the first timer interrupt arrives.
On my setup, the system also boots fine without the 2nd and 3rd KEEP()
statements, so I cannot tell whether these are actually required.
[nathan: Use OVERLAY_KEEP() to avoid breaking old ld.lld versions]
Cc: stable@vger.kernel.org
Fixes: ed0f94102251 ("ARM: 9404/1: arm32: enable HAVE_LD_DEAD_CODE_DATA_ELIMINATION")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 379c590113ce46f605439d4887996c60ab8820cc upstream.
When the addresses of the shmobile_smp_mpidr, shmobile_smp_fn, and
shmobile_smp_arg variables are not multiples of 4 bytes, secondary CPU
bring-up fails:
smp: Bringing up secondary CPUs ...
CPU1: failed to come online
CPU2: failed to come online
CPU3: failed to come online
smp: Brought up 1 node, 1 CPU
Fix this by adding the missing alignment directive.
Fixes: 4e960f52fce16a3b ("ARM: shmobile: Move shmobile_smp_{mpidr, fn, arg}[] from .text to .bss")
Closes: https://lore.kernel.org/r/CAMuHMdU=QR-JLgEHKWpsr6SbaZRc-Hz9r91JfpP8c3n2G-OjqA@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/c499234d559a0d95ad9472883e46077311051cd8.1741612208.git.geert+renesas@glider.be
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83964a29379cb08929a39172780a4c2992bc7c93 upstream.
The current solution for powering off the Apalis iMX6 is not functioning
as intended. To resolve this, it is necessary to power off the
vgen2_reg, which will also set the POWER_ENABLE_MOCI signal to a low
state. This ensures the carrier board is properly informed to initiate
its power-off sequence.
The new solution uses the regulator-poweroff driver, which will power
off the regulator during a system shutdown.
Cc: <stable@vger.kernel.org>
Fixes: 4eb56e26f92e ("ARM: dts: imx6q-apalis: Command pmic to standby for poweroff")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 45d5fe1c53baaed1fb3043f45d1e15ebb4bbe86a ]
Chips in the DA850 family need to have ARCH_DAVINCI_DA8XX to be selected
in order to enable some peripheral drivers.
This was accidentally removed in a previous commit.
Fixes: dec85a95167a ("ARM: davinci: clean up platform support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 24d4c56dd68906bf55ff8fc2e2d36760f97dce5f ]
After using the device for a while, Tom reports that he initially described
the switch port labels incorrectly. Apparently, ASUS's own firmware also
describes them incorrectly. Correct them to what is seen on the chassis.
Reported-by: Tom Brautaset <tbrautaset@gmail.com>
Fixes: b116239094d8 ("ARM: dts: BCM5301X: Add DT for ASUS RT-AC3200")
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://lore.kernel.org/r/20250304-for-broadcom-fix-rt-ac3200-switch-ports-v1-1-7e249a19a13e@arinc9.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 56e12d0c8d395b6e48f128858d4f725c1ded6c95 ]
After using the device for a while, Tom reports that he initially described
the switch port labels incorrectly. Correct them.
Reported-by: Tom Brautaset <tbrautaset@gmail.com>
Fixes: 961dedc6b4e4 ("ARM: dts: BCM5301X: Add DT for ASUS RT-AC5300")
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://lore.kernel.org/r/20250303-for-broadcom-fix-rt-ac5300-switch-ports-v1-1-e058856ef4d3@arinc9.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c24f272ae751a9f54f8816430e7f2d56031892cc ]
During upstream process of Raspberry Pi 4 back in 2019 the ARMv7 stubs
didn't configured the ARM architectural timer. This firmware issue has
been fixed in 2020, which gave users enough time to update their system.
So drop this property to allow the use of the vDSO version of
clock_gettime.
Link: https://github.com/raspberrypi/tools/pull/113
Fixes: 7dbe8c62ceeb ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250222094113.48198-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 98f3ab18a0a55aa1ff2cd6b74bd0c02c8f76f17e ]
When GENERIC_IRQ_CHIP is disabled, OMAP1 kernels fail to link:
arm-linux-gnueabi-ld: arch/arm/mach-omap1/irq.o: in function `omap1_init_irq':
irq.c:(.init.text+0x1e8): undefined reference to `irq_alloc_generic_chip'
arm-linux-gnueabi-ld: irq.c:(.init.text+0x228): undefined reference to `irq_setup_generic_chip'
arm-linux-gnueabi-ld: irq.c:(.init.text+0x2a8): undefined reference to `irq_gc_set_wake'
arm-linux-gnueabi-ld: irq.c:(.init.text+0x2b0): undefined reference to `irq_gc_mask_set_bit'
arm-linux-gnueabi-ld: irq.c:(.init.text+0x2b4): undefined reference to `irq_gc_mask_clr_bit'
This has apparently been the case for many years, but I never caught it
in randconfig builds until now, as there are dozens of other drivers
that also 'select GENERIC_IRQ_CHIP' and statistically there is almost
always one of them enabled.
Fixes: 55b447744389 ("ARM: OMAP1: Switch to use generic irqchip in preparation for sparse IRQ")
Link: https://lore.kernel.org/r/20250205121151.289535-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0de09025f161f67c07978c4742e221243d070d41 ]
The ARM PL011 UART instances in BCM2711 are r1p5 spec, which means they
have 32-entry FIFOs. The correct periphid value for this is 0x00341011.
Thanks to N Buchwitz for pointing this out.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250223125614.3592-2-wahrenst@gmx.net
Fixes: 7dbe8c62ceeb ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f44fa354a0715577ca32b085f6f60bcf32c748dd ]
During s2idle tests on the Raspberry CM4 the VPU firmware always crashes
on xHCI power-domain resume:
root@raspberrypi:/sys/power# echo freeze > state
[ 70.724347] xhci_suspend finished
[ 70.727730] xhci_plat_suspend finished
[ 70.755624] bcm2835-power bcm2835-power: Power grafx off
[ 70.761127] USB: Set power to 0
[ 74.653040] USB: Failed to set power to 1 (-110)
This seems to be caused because of the mixed usage of
raspberrypi-power and bcm2835-power at the same time. So avoid
the usage of the VPU firmware power-domain driver, which
prevents the VPU crash.
Fixes: 522c35e08b53 ("ARM: dts: bcm2711: Add BCM2711 xHCI support")
Link: https://github.com/raspberrypi/linux/issues/6537
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250201112729.31509-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0cfbd7805fe13406500e6a6f2aa08f198d5db4bd upstream.
Despite CM_IDLEST1_CORE and CM_FCLKEN1_CORE behaving normal,
disabling SPI leads to messages like when suspending:
Powerdomain (core_pwrdm) didn't enter target state 0
and according to /sys/kernel/debug/pm_debug/count off state is not
entered. That was not connected to SPI during the discussion
of disabling SPI. See:
https://lore.kernel.org/linux-omap/20230122100852.32ae082c@aktux/
The reason is that SPI is per default in slave mode. Linux driver
will turn it to master per default. It slave mode, the powerdomain seems to
be kept active if active chip select input is sensed.
Fix that by explicitly disabling the SPI3 pins which used to be muxed by
the bootloader since they are available on an optionally fitted header
which would require dtb overlays anyways.
Fixes: a622310f7f01 ("ARM: dts: gta04: fix excess dma channel usage")
CC: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241204174152.2360431-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1472ec1dc4419d0bae663c1a1e6cb98dc7881ad upstream.
A bus_dma_limit was added for l3 bus by commit cfb5d65f2595
("ARM: dts: dra7: Add bus_dma_limit for L3 bus") to fix an issue
observed only with SATA on DRA7-EVM with 4GB RAM and CONFIG_ARM_LPAE
enabled.
Since kernel 5.13, the SATA issue can be reproduced again following
the SATA node move from L3 bus to L4_cfg in commit 8af15365a368
("ARM: dts: Configure interconnect target module for dra7 sata").
Fix it by adding an empty dma-ranges property to l4_cfg and
segment@100000 nodes (parent device tree node of SATA controller) to
inherit the 2GB dma ranges limit from l3 bus node.
Note: A similar fix was applied for PCIe controller by commit
90d4d3f4ea45 ("ARM: dts: dra7: Fix bus_dma_limit for PCIe").
Fixes: 8af15365a368 ("ARM: dts: Configure interconnect target module for dra7 sata").
Link: https://lore.kernel.org/linux-omap/c583e1bb-f56b-4489-8012-ce742e85f233@smile.fr/
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Romain Naour <romain.naour@skf.com>
Link: https://lore.kernel.org/r/20241115102537.1330300-1-romain.naour@smile.fr
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 90234cf9b37c57201a24b78c217a91a8af774109 ]
Fix following validation error:
arch/arm/boot/dts/mediatek/mt7623a-rfb-emmc.dtb: cir@10013000: $nodename:0: 'cir@10013000' does not match '^ir(-receiver)?(@[a-f0-9]+)?$'
from schema $id: http://devicetree.org/schemas/media/mediatek,mt7622-cir.yaml#
Fixes: 91044f38dae7 ("arm: dts: mt7623: add ir nodes to the mt7623.dtsi file")
Cc: linux-media@vger.kernel.org
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240617094634.23173-1-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ad455e48bba7f21bb5108406da0854cf8dede8ea ]
The Retu IRQ is off by one, as a result the power button does not work.
Fix it.
Fixes: 084b6f216778 ("ARM: omap1: Fix up the Nokia 770 board device IRQs")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/Z3UxH_fOzuftjnuX@darkstar.musicnaut.iki.fi
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d9e5965df04c0adf260c3009c55d5fe240f7286 ]
Add no-1-8-v property to sdmmc0 node to keep VDDSDMMC power rail at 3.3V.
This property will stop the LDO regulator from switching to 1.8V when the
MMC core detects an UHS SD Card. VDDSDMMC power rail is used by all the
SDMMC interface pins in GPIO mode (PA0 - PA13).
On this board, PA10 is used as GPIO to enable the power switch controlling
USB Vbus for the USB Host. The change is needed to fix the PA10 voltage
level to 3.3V instead of 1.8V.
Fixes: 5d4c3cfb63fe ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Suggested-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20241119160107.598411-3-cristian.birsan@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c21c23a0f2e9869676eff0d53fb89e151e14c873 ]
Add no-1-8-v property to sdmmc0 node to keep VDDSDMMC power rail at 3.3V.
This property will stop the LDO regulator from switching to 1.8V when the
MMC core detects an UHS SD Card. VDDSDMMC power rail is used by all the
SDMMC interface pins in GPIO mode (PA0 - PA13).
On this board, PA6 is used as GPIO to enable the power switch controlling
USB Vbus for the USB Host. The change is needed to fix the PA6 voltage
level to 3.3V instead of 1.8V.
Fixes: d85c4229e925 ("ARM: dts: at91: sama5d29_curiosity: Add device tree for sama5d29_curiosity board")
Suggested-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20241119160107.598411-2-cristian.birsan@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 479b8227ffc433929ba49200182b6383569f9615 ]
Swap USART3 and UART8 aliases on STM32MP15xx DHCOM SoM,
make sure UART8 is listed first, USART3 second, because
the UART8 is labeled as UART2 on the SoM pinout, while
USART3 is labeled as UART3 on the SoM pinout.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
DHCOM SoM
[ Upstream commit 73317d327123472cb70e9ecbe050310f1d235e93 ]
Deduplicate /aliases { serialN = ... } and /chosen node into
stm32mp15xx-dhcom-som.dtsi , since the content is identical
on all carrier boards using the STM32MP15xx DHCOM SoM. No
functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: 479b8227ffc4 ("ARM: dts: stm32: Swap USART3 and UART8 alias on STM32MP15xx DHCOM SoM")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 62a40a0d5634834790f7166ab592be247390d857 ]
The ahb reset is deasserted in probe before first register access, while the
stmmacheth-ocp reset needs to be asserted every time before changing the phy
mode in Arria10[1].
Changed in Upstream to "ahb"(331085a423b arm64: dts: socfpga: change the
reset-name of "stmmaceth-ocp" to "ahb" ).This change was intended for arm64
socfpga and it is not applicable to Arria10.
Further with STMMAC-SELFTEST Driver enabled, ethtool test also FAILS.
$ ethtool -t eth0
[ 322.946709] socfpga-dwmac ff800000.ethernet eth0: entered promiscuous mode
[ 323.374558] socfpga-dwmac ff800000.ethernet eth0: left promiscuous mode
The test result is FAIL
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -110
3. MMC Counters -110
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC -110
7. MC Filter -110
8. UC Filter 0
9. Flow Control -110
10. RSS -95
11. VLAN Filtering -95
12. VLAN Filtering (perf) -95
13. Double VLAN Filter -95
14. Double VLAN Filter (perf) -95
15. Flexible RX Parser -95
16. SA Insertion (desc) -95
17. SA Replacement (desc) -95
18. SA Insertion (reg) -95
19. SA Replacement (reg) -95
20. VLAN TX Insertion -95
21. SVLAN TX Insertion -95
22. L3 DA Filtering -95
23. L3 SA Filtering -95
24. L4 DA TCP Filtering -95
25. L4 SA TCP Filtering -95
26. L4 DA UDP Filtering -95
27. L4 SA UDP Filtering -95
28. ARP Offload -95
29. Jumbo Frame -110
30. Multichannel Jumbo -95
31. Split Header -95
32. TBS (ETF Scheduler) -95
[ 324.881327] socfpga-dwmac ff800000.ethernet eth0: Link is Down
[ 327.995360] socfpga-dwmac ff800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Link:[1] https://www.intel.com/content/www/us/en/docs/programmable/683711/21-2/functional-description-of-the-emac.html
Fixes: 331085a423b ("arm64: dts: socfpga: change the reset-name of "stmmaceth-ocp" to "ahb")
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b1a1ecb669bfa763ee5e86a038d7c9363eee7548 ]
Fix the compatible string for max31790 to match the binding document.
Fixes: 2b8d94f4b4a4 ("ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC")
Signed-off-by: Ricky CX Wu <ricky.cx.wu.wiwynn@gmail.com>
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Link: https://patch.msgid.link/20241003074251.3818101-6-Delphine_CC_Chiu@wiwynn.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c64ac96f8f8d957cdc6ec3c93dd9a6c4e6d78506 ]
Add the required properties for IO expander on fan boards.
Fixes: 2b8d94f4b4a4 ("ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC")
Signed-off-by: Ricky CX Wu <ricky.cx.wu.wiwynn@gmail.com>
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Link: https://patch.msgid.link/20241003074251.3818101-5-Delphine_CC_Chiu@wiwynn.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ece3e20e3389ec8a32944ad44746ee379bf1d3eb ]
Remove the space in the compatible string of adm1272 to match the
pattern of compatible.
Fixes: 2b8d94f4b4a4 ("ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC")
Signed-off-by: Ricky CX Wu <ricky.cx.wu.wiwynn@gmail.com>
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Fixes: 2b8d94f4b4a4765d ("ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC")
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://patch.msgid.link/20240927085213.331127-1-Delphine_CC_Chiu@wiwynn.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ea654242e0c75bdf6b45d3c619c5fdcb2e9312a ]
The GIC IRQ type used for IPCC RX should be IRQ_TYPE_LEVEL_HIGH.
Replacing the interrupt with the EXTI event changes the type to
the numeric value 1, meaning IRQ_TYPE_EDGE_RISING.
The issue is that EXTI event 61 is a direct event.The IRQ type of
direct events is not used by EXTI and is propagated to the parent
IRQ controller of EXTI, the GIC.
Align the IRQ type to the value expected by the GIC by replacing
the second parameter "1" with IRQ_TYPE_LEVEL_HIGH.
Fixes: 7d9802bb0e34 ("ARM: dts: stm32: remove the IPCC "wakeup" IRQ on stm32mp151")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a4422a9183278162093d4524fdf4b6bbd7dd8a28 ]
The STM32MP13xx DHCOR DHSBC is populated with STM32MP13xx part capable
of 1 GHz operation, increase the CPU core voltage to 1.35 V to make
sure the SoC is stable even if the blobs unconditionally force the CPU
to 1 GHz operation.
It is not possible to make use of CPUfreq on the STM32MP13xx because
the SCMI protocol 0x13 is not implemented by upstream OpTee-OS which
is the SCMI provider.
Fixes: 6331bddce649 ("ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 78e08cebfe41a99d12a3a79d3e3be913559182e2 ]
Add missing supply for LM75. Fixes the kernel warning:
lm75 0-0048: supply vs not found, using dummy regulator
Fixes: c9d4affbe60a ("ARM: dts: imx: tqma7: add lm75a sensor (rev. 01xxx)")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Markus Niebel <markus.niebel@ew.tq-group.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6fc5bdfa872b7da51b5507a1327a17c3db2fcf95 ]
Change how the Backup Unit Power is configured and force the
automatic/hardware mode.
This change eliminates the need for software management of the power
switch, ensuring it transitions to the backup power source before
entering low power modes.
This is done in the only location where this switch was configured. It's
usually done in the bootloader.
Previously, the loss of the VDDANA (or VDDIN33) power source was not
automatically compensated by an alternative power source. This resulted
in the loss of Backup Unit content, including Backup Self-refresh low
power mode information, OTP emulation configuration, and boot
configuration, for instance.
Fixes: ac809e7879b1 ("ARM: at91: pm: switch backup area to vbat in backup mode")
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20241125165648.509162-1-nicolas.ferre@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5f122030061db3e5d2bddd9cf5c583deaa6c54ff ]
One of the usdhc1 controller's clocks should be IMXRT1050_CLK_AHB_PODF not
IMXRT1050_CLK_OSC.
Fixes: 1c4f01be3490 ("ARM: dts: imx: Add i.MXRT1050-EVK support")
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 93ee385254d53849c01dd8ab9bc9d02790ee7f0e upstream.
The code for syncing vmalloc memory PGD pointers is using
atomic_read() in pair with atomic_set_release() but the
proper pairing is atomic_read_acquire() paired with
atomic_set_release().
This is done to clearly instruct the compiler to not
reorder the memcpy() or similar calls inside the section
so that we do not observe changes to init_mm. memcpy()
calls should be identified by the compiler as having
unpredictable side effects, but let's try to be on the
safe side.
Cc: stable@vger.kernel.org
Fixes: d31e23aff011 ("ARM: mm: make vmalloc_seq handling SMP safe")
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 44e9a3bb76e5f2eecd374c8176b2c5163c8bb2e2 upstream.
When switching task, in addition to a dummy read from the new
VMAP stack, also do a dummy read from the VMAP stack's
corresponding KASAN shadow memory to sync things up in
the new MM context.
Cc: stable@vger.kernel.org
Fixes: a1c510d0adc6 ("ARM: implement support for vmap'ed stacks")
Link: https://lore.kernel.org/linux-arm-kernel/a1a1d062-f3a2-4d05-9836-3b098de9db6d@foss.st.com/
Reported-by: Clement LE GOFFIC <clement.legoffic@foss.st.com>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6e6a74d4cea853b5321eeabb69c611148eedefe upstream.
When sync:ing the VMALLOC area to other CPUs, make sure to also
sync the KASAN shadow memory for the VMALLOC area, so that we
don't get stale entries for the shadow memory in the top level PGD.
Since we are now copying PGDs in two instances, create a helper
function named memcpy_pgd() to do the actual copying, and
create a helper to map the addresses of VMALLOC_START and
VMALLOC_END into the corresponding shadow memory.
Co-developed-by: Melon Liu <melon1335@163.com>
Cc: stable@vger.kernel.org
Fixes: 565cbaad83d8 ("ARM: 9202/1: kasan: support CONFIG_KASAN_VMALLOC")
Link: https://lore.kernel.org/linux-arm-kernel/a1a1d062-f3a2-4d05-9836-3b098de9db6d@foss.st.com/
Reported-by: Clement LE GOFFIC <clement.legoffic@foss.st.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96a64e9730c2c76cfa5c510583a0fbf40d62886b upstream.
Operating stable without reduced chip life at 1Ghz needs several
technologies working: The technologies involve
- SmartReflex
- DVFS
As this cannot directly specified in the OPP table as dependecies in the
devicetree yet, use the turbo flag again to mark this OPP as something
special to have some kind of opt-in.
So revert commit
5f1bf7ae8481 ("ARM: dts: omap36xx: Remove turbo mode for 1GHz variants")
Practical reasoning:
At least the GTA04A5 (DM3730) has become unstable with that OPP enabled.
Furthermore nothing enforces the availability of said technologies,
even in the kernel configuration, so allow users to rather opt-in.
Cc: Stable@vger.kernel.org
Fixes: 5f1bf7ae8481 ("ARM: dts: omap36xx: Remove turbo mode for 1GHz variants")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20241018214727.275162-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b2473a359763e27567993e7d8f37de82f57a0829 ]
__pa() is only intended to be used for linear map addresses and using
it for initial_boot_params which is in fixmap for arm64 will give an
incorrect value. Hence save the physical address when it is known at
boot time when calling early_init_dt_scan for arm64 and use it at kexec
time instead of converting the virtual address using __pa().
Note that arm64 doesn't need the FDT region reserved in the DT as the
kernel explicitly reserves the passed in FDT. Therefore, only a debug
warning is fixed with this change.
Reported-by: Breno Leitao <leitao@debian.org>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Usama Arif <usamaarif642@gmail.com>
Fixes: ac10be5cdbfa ("arm64: Use common of_kexec_alloc_and_setup_fdt()")
Link: https://lore.kernel.org/r/20241023171426.452688-1-usamaarif642@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dd36ad71ad65968f97630808bc8d605c929b128e ]
The DCDC5 voltage rail in the X-Powers AXP809 PMIC has a resolution of
50mV, so the currently enforced limits of 1.475 and 1.525 volts cannot
be set, when the existing regulator value is beyond this range.
This will lead to the whole regulator driver to give up and fail
probing, which in turn will hang the system, as essential devices depend
on the PMIC.
In this case a bug in U-Boot set the voltage to 1.75V (meant for DCDC4),
and the AXP driver's attempt to correct this lead to this error:
==================
[ 4.447653] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded
[ 4.450066] vcc-dram: Bringing 1750000uV into 1575000-1575000uV
[ 4.460272] vcc-dram: failed to apply 1575000-1575000uV constraint: -EINVAL
[ 4.474788] axp20x-regulator axp20x-regulator.0: Failed to register dcdc5
[ 4.482276] axp20x-regulator axp20x-regulator.0: probe with driver axp20x-regulator failed with error -22
==================
Set the limits to values that can be programmed, so any correction will
be successful.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fixes: 1e1dea72651b ("ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators")
Link: https://patch.msgid.link/20241007222916.19013-1-andre.przywara@arm.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2f9d013a0c6f1b9109ada5acb28ee26eefc77c03 ]
Add the atmel,usart-mode property to the UART nodes. This ensures
compliance with the atmel,at91-usart.yaml schema and resolves the errors
below:
serial@200: $nodename:0: 'serial@200' does not match
'^spi(@.*|-([0-9]|[1-9][0-9]+))?$'
serial@200: atmel,use-dma-rx: False schema does not allow True
serial@200: atmel,use-dma-tx: False schema does not allow True
serial@200: atmel,fifo-size: False schema does not allow [[16]]
These errors indicate that the property
atmel,usart-mode = <AT91_USART_MODE_SERIAL> is missing for
UART nodes 0, 1, 2, 3, 4, 6, 7, 8, 9, 10, 11, and 12.
Fixes: 99c808335877 ("ARM: dts: at91: sam9x60: Add missing flexcom definitions")
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20240912093307.40488-1-andrei.simion@microchip.com
[claudiu.beznea: move the atmel,usart-mode close to vendor specific
properties to cope with DTS coding style]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 48e17816c3effa3545e21cd4f7d5a00c55c17a18 ]
Second partition was too large, looks like two digits got mixed up.
Fixes:
mtd: partition "user1" extends beyond the end of device "18000000.flash" -- size truncated to 0x4000000
Fixes: 30e0a8cf886c ("ARM: dts: renesas: genmai: Add FLASH nodes")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240914182948.94031-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
