| Age | Commit message (Collapse) | Author |
|---|
|
Avoid explicit literal loads and instead, use accessor macros that
generate the optimal sequence depending on the architecture revision
being targeted.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Tweak the ftrace return paths to avoid redundant loads of SP, as well as
unnecessary clobbering of IP.
This also fixes the inconsistency of using MOV to perform a function
return, which is sub-optimal on recent micro-architectures but more
importantly, does not perform an interworking return, unlike compiler
generated function returns in Thumb2 builds.
Let's fix this by popping PC from the stack like most ordinary code
does.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Kernel images that are large in comparison to the range of a direct
branch may fail to work as expected with ftrace, as patching a direct
branch to one of the core ftrace routines may not be possible from the
.init.text section, if it is emitted too far away from the normal .text
section.
This is more likely to affect Thumb2 builds, given that its range is
only -/+ 16 MiB (as opposed to ARM which has -/+ 32 MiB), but may occur
in either ISA.
To work around this, add a couple of trampolines to .init.text and
swap these in when the ftrace patching code is operating on callers in
.init.text.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The compiler emitted hook used for ftrace consists of a PUSH {LR} to
preserve the link register, followed by a branch-and-link (BL) to
__gnu_mount_nc. Dynamic ftrace patches away the latter to turn the
combined sequence into a NOP, using a POP {LR} instruction.
This is not necessary, since the link register does not get clobbered in
this case, and simply adding #4 to the stack pointer is sufficient, and
avoids a memory access that may take a few cycles to resolve depending
on the micro-architecture.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Using ADR to take the address of 'ftrace_stub' via a local label
produces an address that has the Thumb bit cleared, which means the
subsequent comparison is guaranteed to fail. Instead, use the badr
macro, which forces the Thumb bit to be set.
Fixes: a3ba87a61499 ("ARM: 6316/1: ftrace: add Thumb-2 support")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Only SMP systems use the secondary startup path by definition, so there
is no need for SMP conditionals there.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Rework the vmalloc_seq handling so it can be used safely under SMP, as
we started using it to ensure that vmap'ed stacks are guaranteed to be
mapped by the active mm before switching to a task, and here we need to
ensure that changes to the page tables are visible to other CPUs when
they observe a change in the sequence count.
Since LPAE needs none of this, fold a check against it into the
vmalloc_seq counter check after breaking it out into a separate static
inline helper.
Given that vmap'ed stacks are now also supported on !SMP configurations,
let's drop the WARN() that could potentially now fire spuriously.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Avoid using R9 in the IRQ handler code, as the entry code uses it for
tsk, and expects it to remain untouched between the IRQ entry and exit
code.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Use the SMP_ON_UP patching framework to elide HWCAP_TLS tests from the
context switch and return to userspace code paths, as SMP systems are
guaranteed to have this h/w capability.
At the same time, omit the update of __entry_task if the system is
detected to be UP at runtime, as in that case, the value is never used.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Nathan reports the group relocations go out of range in pathological
cases such as allyesconfig kernels, which have little chance of actually
booting but are still used in validation.
So add a Kconfig symbol for this feature, and make it depend on
!COMPILE_TEST.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
When onlining a CPU, switch to swapper_pg_dir as soon as possible so
that it is guaranteed that the vmap'ed stack is mapped before it is
used.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Remove PDE_DATA() completely and replace it with pde_data().
[akpm@linux-foundation.org: fix naming clash in drivers/nubus/proc.c]
[akpm@linux-foundation.org: now fix it properly]
Link: https://lkml.kernel.org/r/20211124081956.87711-2-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alexey Gladkov <gladkov.alexey@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull signal/exit/ptrace updates from Eric Biederman:
"This set of changes deletes some dead code, makes a lot of cleanups
which hopefully make the code easier to follow, and fixes bugs found
along the way.
The end-game which I have not yet reached yet is for fatal signals
that generate coredumps to be short-circuit deliverable from
complete_signal, for force_siginfo_to_task not to require changing
userspace configured signal delivery state, and for the ptrace stops
to always happen in locations where we can guarantee on all
architectures that the all of the registers are saved and available on
the stack.
Removal of profile_task_ext, profile_munmap, and profile_handoff_task
are the big successes for dead code removal this round.
A bunch of small bug fixes are included, as most of the issues
reported were small enough that they would not affect bisection so I
simply added the fixes and did not fold the fixes into the changes
they were fixing.
There was a bug that broke coredumps piped to systemd-coredump. I
dropped the change that caused that bug and replaced it entirely with
something much more restrained. Unfortunately that required some
rebasing.
Some successes after this set of changes: There are few enough calls
to do_exit to audit in a reasonable amount of time. The lifetime of
struct kthread now matches the lifetime of struct task, and the
pointer to struct kthread is no longer stored in set_child_tid. The
flag SIGNAL_GROUP_COREDUMP is removed. The field group_exit_task is
removed. Issues where task->exit_code was examined with
signal->group_exit_code should been examined were fixed.
There are several loosely related changes included because I am
cleaning up and if I don't include them they will probably get lost.
The original postings of these changes can be found at:
https://lkml.kernel.org/r/87a6ha4zsd.fsf@email.froward.int.ebiederm.org
https://lkml.kernel.org/r/87bl1kunjj.fsf@email.froward.int.ebiederm.org
https://lkml.kernel.org/r/87r19opkx1.fsf_-_@email.froward.int.ebiederm.org
I trimmed back the last set of changes to only the obviously correct
once. Simply because there was less time for review than I had hoped"
* 'signal-for-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (44 commits)
ptrace/m68k: Stop open coding ptrace_report_syscall
ptrace: Remove unused regs argument from ptrace_report_syscall
ptrace: Remove second setting of PT_SEIZED in ptrace_attach
taskstats: Cleanup the use of task->exit_code
exit: Use the correct exit_code in /proc/<pid>/stat
exit: Fix the exit_code for wait_task_zombie
exit: Coredumps reach do_group_exit
exit: Remove profile_handoff_task
exit: Remove profile_task_exit & profile_munmap
signal: clean up kernel-doc comments
signal: Remove the helper signal_group_exit
signal: Rename group_exit_task group_exec_task
coredump: Stop setting signal->group_exit_task
signal: Remove SIGNAL_GROUP_COREDUMP
signal: During coredumps set SIGNAL_GROUP_EXIT in zap_process
signal: Make coredump handling explicit in complete_signal
signal: Have prepare_signal detect coredumps using signal->core_state
signal: Have the oom killer detect coredumps using signal->core_state
exit: Move force_uaccess back into do_exit
exit: Guarantee make_task_dead leaks the tsk when calling do_task_exit
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Borislav Petkov:
"Cleanup of the perf/kvm interaction."
* tag 'perf_core_for_v5.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Drop guest callback (un)register stubs
KVM: arm64: Drop perf.c and fold its tiny bits of code into arm.c
KVM: arm64: Hide kvm_arm_pmu_available behind CONFIG_HW_PERF_EVENTS=y
KVM: arm64: Convert to the generic perf callbacks
KVM: x86: Move Intel Processor Trace interrupt handler to vmx.c
KVM: Move x86's perf guest info callbacks to generic KVM
KVM: x86: More precisely identify NMI from guest when handling PMI
KVM: x86: Drop current_vcpu for kvm_running_vcpu + kvm_arch_vcpu variable
perf/core: Use static_call to optimize perf_guest_info_callbacks
perf: Force architectures to opt-in to guest callbacks
perf: Add wrappers for invoking guest callbacks
perf/core: Rework guest callbacks to prepare for static_call support
perf: Drop dead and useless guest "support" from arm, csky, nds32 and riscv
perf: Stop pretending that perf can handle multiple guest callbacks
KVM: x86: Register Processor Trace interrupt hook iff PT enabled in guest
KVM: x86: Register perf callbacks after calling vendor's hardware_setup()
perf: Protect perf_guest_cbs with RCU
|
|
Pull ARM updates from Russell King:
- amba bus irq rework
- add kfence support
- support for Cortex M33 and M55 CPUs
- kbuild updates for decompressor
- let core code manage thread_info::cpu
- avoid unpredictable NOP encoding in decompressor
- reduce information printed in calltraces
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: reduce the information printed in call traces
ARM: 9168/1: Add support for Cortex-M55 processor
ARM: 9167/1: Add support for Cortex-M33 processor
ARM: 9166/1: Support KFENCE for ARM
ARM: 9165/1: mm: Provide is_write_fault()
ARM: 9164/1: mm: Provide set_memory_valid()
ARM: 9163/1: amba: Move of_amba_device_decode_irq() into amba_probe()
ARM: 9162/1: amba: Kill sysfs attribute file of irq
ARM: 9161/1: mm: mark private VM_FAULT_X defines as vm_fault_t
ARM: 9159/1: decompressor: Avoid UNPREDICTABLE NOP encoding
ARM: 9158/1: leave it to core code to manage thread_info::cpu
ARM: 9154/1: decompressor: do not copy source files while building
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull thread_info flag accessor helper updates from Borislav Petkov:
"Add a set of thread_info.flags accessors which snapshot it before
accesing it in order to prevent any potential data races, and convert
all users to those new accessors"
* tag 'core_entry_for_v5.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
powerpc: Snapshot thread flags
powerpc: Avoid discarding flags in system_call_exception()
openrisc: Snapshot thread flags
microblaze: Snapshot thread flags
arm64: Snapshot thread flags
ARM: Snapshot thread flags
alpha: Snapshot thread flags
sched: Snapshot thread flags
entry: Snapshot thread flags
x86: Snapshot thread flags
thread_info: Add helpers to snapshot thread flags
|
|
The Thumb2 version of the FP exception handling entry code treats the
register holding the CP number (R8) differently, resulting in the iWMMXT
CP number check to be incorrect.
Fix this by unifying the ARM and Thumb2 code paths, and switch the
order of the additions of the TI_USED_CP offset and the shifted CP
index.
Cc: <stable@vger.kernel.org>
Fixes: b86040a59feb ("Thumb-2: Implementation of the unified start-up and exceptions code")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
__secondary_data used to reside in r7 around call to
PROCINFO_INITFUNC. After commit 95731b8ee63e ("ARM: 9059/1: cache-v7:
get rid of mini-stack") r7 is used as a scratch register, so we have
to reload __secondary_data before we setup the stack pointer.
Fixes: 95731b8ee63e ("ARM: 9059/1: cache-v7: get rid of mini-stack")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
A while back, Linus complained about the numeric values printed by the
ARM backtracing code. Printing these values does not make sense if one
does not have access to the kernel ELF image (as is normally the case
when helping a third party on a mailing list), but if one does, they
can be very useful to find the code, rather than searching for the
function name, and then doing hex math to work out where the backtrace
entry is referring to.
Provide an option to control whether this information is included,
which will only be visible if EXPERT is enabled.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Since commit bcf9033e5449 ("sched: move CPU field back into thread_info
if THREAD_INFO_IN_TASK=y"), the CPU field in thread_info went back to
being managed by the core code, so we no longer have to keep it in sync
in arch code.
While at it, mark THREAD_INFO_IN_TASK as done for ARM in the
documentation.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
There are two big uses of do_exit. The first is it's design use to be
the guts of the exit(2) system call. The second use is to terminate
a task after something catastrophic has happened like a NULL pointer
in kernel code.
Add a function make_task_dead that is initialy exactly the same as
do_exit to cover the cases where do_exit is called to handle
catastrophic failure. In time this can probably be reduced to just a
light wrapper around do_task_dead. For now keep it exactly the same so
that there will be no behavioral differences introducing this new
concept.
Replace all of the uses of do_exit that use it for catastraphic
task cleanup with make_task_dead to make it clear what the code
is doing.
As part of this rename rewind_stack_do_exit
rewind_stack_and_make_dead.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Enable support for IRQ stacks on !MMU, and add the code to the IRQ entry
path to switch to the IRQ stack if not running from it already.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
On UP systems, only a single task can be 'current' at the same time,
which means we can use a global variable to track it. This means we can
also enable THREAD_INFO_IN_TASK for those systems, as in that case,
thread_info is accessed via current rather than the other way around,
removing the need to store thread_info at the base of the task stack.
This, in turn, permits us to enable IRQ stacks and vmap'ed stacks on UP
systems as well.
To partially mitigate the performance overhead of this arrangement, use
a ADD/ADD/LDR sequence with the appropriate PC-relative group
relocations to load the value of current when needed. This means that
accessing current will still only require a single load as before,
avoiding the need for a literal to carry the address of the global
variable in each function. However, accessing thread_info will now
require this load as well.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
Defer TPIDURO updates for user space until exit also for CPU_V6+SMP
configurations so that we can decide at runtime whether to use it to
carry the current pointer, provided that we are running on a CPU that
actually implements this register. This is needed for
THREAD_INFO_IN_TASK support for UP systems, which requires that all SMP
capable systems use the TPIDRURO based access to 'current' as the only
remaining alternative will be a global variable which only works on UP.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
Permit the use of the TPIDRPRW system register for carrying the per-CPU
offset in generic SMP configurations that also target non-SMP capable
ARMv6 cores. This uses the SMP_ON_UP code patching framework to turn all
TPIDRPRW accesses into reads/writes of entry #0 in the __per_cpu_offset
array.
While at it, switch over some existing direct TPIDRPRW accesses in asm
code to invocations of a new helper that is patched in the same way when
necessary.
Note that CPU_V6+SMP without SMP_ON_UP results in a kernel that does not
boot on v6 CPUs without SMP extensions, so add this dependency to
Kconfig as well.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
We will be adding variable loads to various hot paths, so it makes sense
to add a helper macro that can load variables from asm code without the
use of literal pool entries. On v7 or later, we can simply use MOVW/MOVT
pairs, but on earlier cores, this requires a bit of hackery to emit a
instruction sequence that implements this using a sequence of ADD/LDR
instructions.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
Add support for the R_ARM_ALU_PC_Gn_NC and R_ARM_LDR_PC_G2 group
relocations [0] so we can use them in modules. These will be used to
load the current task pointer from a global variable without having to
rely on a literal pool entry to carry the address of this variable,
which may have a significant negative impact on cache utilization for
variables that are used often and in many different places, as each
occurrence will result in a literal pool entry and therefore a line in
the D-cache.
[0] 'ELF for the ARM architecture'
https://github.com/ARM-software/abi-aa/releases
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
Tweak the UP stack protector handling code so that the thread info
pointer is preserved in R7 until set_current is called. This is needed
for a subsequent patch that implements THREAD_INFO_IN_TASK and
set_current for UP as well.
This also means we will prefer the per-task protector on UP systems that
implement the thread ID registers, so tweak the preprocessor
conditionals to reflect this.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
Rather then restructuring the ARMv7M entrly logic per TODO, just move
NVIC to GENERIC_IRQ_MULTI_HANDLER.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
The last user of arch_irq_handler_default is gone now, so the
entry-macro-multi.S file and all references to mach/entry-macro.S can
be removed, as well as the asm_do_IRQ() entrypoint into the interrupt
handling routines implemented in C.
Note: The ARMv7-M entry still uses its own top-level IRQ entry, calling
nvic_handle_irq() from assembly. This could be changed to go through
generic_handle_arch_irq() as well, but it's unclear to me if there are
any benefits.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[ardb: keep irq_handler macro as it carries all the IRQ stack handling]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
iop32x uses the entry-macro.S file for both the IRQ entry and for
hooking into the arch_ret_to_user code path. This is done because the
cp6 registers have to be enabled before accessing any of the interrupt
controller registers but have to be disabled when running in user space.
There is also a lazy-enable logic in cp6.c, but during a hardirq, we
know it has to be enabled.
Both the cp6-enable code and the code to read the IRQ status can be
lifted into the normal generic_handle_arch_irq() path, but the
cp6-disable code has to remain in the user return code. As nothing
other than iop32x uses this hook, just open-code it there with an
ifdef for the platform that can eventually be removed when iop32x
has reached the end of its life.
The cp6-enable path in the IRQ entry has an extra cp_wait barrier that
the trap version does not have, but it is harmless to do it in both
cases to simplify the logic here at the cost of a few extra cycles
for the trap.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
Wire up the generic support for managing task stack allocations via vmalloc,
and implement the entry code that detects whether we faulted because of a
stack overrun (or future stack overrun caused by pushing the pt_regs array)
While this adds a fair amount of tricky entry asm code, it should be
noted that it only adds a TST + branch to the svc_entry path. The code
implementing the non-trivial handling of the overflow stack is emitted
out-of-line into the .text section.
Since on ARM, we rely on do_translation_fault() to keep PMD level page
table entries that cover the vmalloc region up to date, we need to
ensure that we don't hit such a stale PMD entry when accessing the
stack. So we do a dummy read from the new stack while still running from
the old one on the context switch path, and bump the vmalloc_seq counter
when PMD level entries in the vmalloc range are modified, so that the MM
switch fetches the latest version of the entries.
Note that we need to increase the per-mode stack by 1 word, to gain some
space to stash a GPR until we know it is safe to touch the stack.
However, due to the cacheline alignment of the struct, this does not
actually increase the memory footprint of the struct stack array at all.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Keith Packard <keithpac@amazon.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
The original Thumb-2 enablement patches updated the stack realignment
code in svc_entry to work around the lack of a STMIB instruction in
Thumb-2, by subtracting 4 from the frame size, inverting the sense of
the misaligment check, and changing to a STMIA instruction and a final
stack push of a 4 byte quantity that results in the stack becoming
aligned at the end of the sequence. It also pushes and pops R0 to the
stack in order to have a temp register that Thumb-2 allows in general
purpose ALU instructions, as TST using SP is not permitted.
Both are a bit problematic for vmap'ed stacks, as using the stack is
only permitted after we decide that we did not overflow the stack, or
have already switched to the overflow stack.
As for the alignment check: the current approach creates a corner case
where, if the initial SUB of SP ends up right at the start of the stack,
we will end up subtracting another 8 bytes and overflowing it. This
means we would need to add the overflow check *after* the SUB that
deliberately misaligns the stack. However, this would require us to keep
local state (i.e., whether we performed the subtract or not) across the
overflow check, but without any GPRs or stack available.
So let's switch to an approach where we don't use the stack, and where
the alignment check of the stack pointer occurs in the usual way, as
this is guaranteed not to result in overflow. This means we will be able
to do the overflow check first.
While at it, switch to R1 so the mode stack pointer in R0 remains
accessible.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
The load-multiple instruction that essentially performs the switch_to
operation in ARM mode, by loading all callee save registers as well the
stack pointer and the program counter, is split into 3 separate loads
for Thumb-2, with the IP register used as a temporary to capture the
value of R4 before it gets overwritten.
We can clean this up a bit, by sticking with a single LDMIA instruction,
but one that pops SP and PC into IP and LR, respectively, and by using
ordinary move register and branch instructions to get those values into
SP and PC. This also allows us to move the set_current call closer to
the assignment of SP, reducing the window where those are mutually out
of sync. This is especially relevant for CONFIG_VMAP_STACK, which is
being introduced in a subsequent patch, where we need to issue a load
that might fault from the new stack while running from the old one, to
ensure that stale PMD entries in the VMALLOC space are synced up.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Keith Packard <keithpac@amazon.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
When unwinding the stack from a stack overflow, we are likely to start
from a stack push instruction, given that this is the most common way to
grow the stack for compiler emitted code. This push instruction rarely
appears anywhere else than at offset 0x0 of the function, and if it
doesn't, the compiler tends to split up the unwind annotations, given
that the stack frame layout is apparently not the same throughout the
function.
This means that, in the general case, if the frame's PC points at the
first instruction covered by a certain unwind entry, there is no way the
stack frame that the unwind entry describes could have been created yet,
and so we are still on the stack frame of the caller in that case. So
treat this as a special case, and return with the new PC taken from the
frame's LR, without applying the unwind transformations to the virtual
register set.
This permits us to unwind the call stack on stack overflow when the
overflow was caused by a stack push on function entry.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Keith Packard <keithpac@amazon.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
Now that we have enabled IRQ stacks, any softIRQs that are handled over
the back of a hard IRQ will run from the IRQ stack as well. However, any
synchronous softirq processing that happens when re-enabling softIRQs
from task context will still execute on that task's stack.
Since any call to local_bh_enable() at any level in the task's call
stack may trigger a softIRQ processing run, which could potentially
cause a task stack overflow if the combined stack footprints exceed the
stack's size, let's run these synchronous invocations of do_softirq() on
the IRQ stack as well.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Keith Packard <keithpac@amazon.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
Now that we no longer rely on the stack pointer to access the current
task struct or thread info, we can implement support for IRQ stacks
cleanly as well.
Define a per-CPU IRQ stack and switch to this stack when taking an IRQ,
provided that we were not already using that stack in the interrupted
context. This is never the case for IRQs taken from user space, but ones
taken while running in the kernel could fire while one taken from user
space has not completed yet.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Keith Packard <keithpac@amazon.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
The existing code that dumps the contents of the pt_regs structure
passed to __entry routines does so while unwinding the callee frame, and
dereferences the stack pointer as a struct pt_regs*. This will no longer
work when we enable support for IRQ or overflow stacks, because the
struct pt_regs may live on the task stack, while we are executing from
another stack.
The unwinder has access to this information, but only while unwinding
the calling frame. So let's combine the exception stack dumping code
with the handling of the calling frame as well. By printing it before
dumping the caller/callee addresses, the output order is preserved.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Keith Packard <keithpac@amazon.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
The unwind info based stack unwinder will make its own call to
dump_mem() to dump the exception stack, so give it external linkage.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Keith Packard <keithpac@amazon.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
Implement support in the unwinder for dealing with multiple stacks.
This will be needed once we add support for IRQ stacks, or for the
overflow stack used by the vmap'ed stacks code.
This involves tracking the unwind opcodes that either update the virtual
stack pointer from another virtual register, or perform an explicit
subtract on the virtual stack pointer, and updating the low and high
bounds that we use to sanitize the stack pointer accordingly.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Keith Packard <keithpac@amazon.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
This code appears to be no longer used so let's get rid of it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Keith Packard <keithpac@amazon.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
|
|
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Generally this is unlikely to cause a
problem in practice, but it is somewhat unsound, and KCSAN will
legitimately warn that there is a data race.
To avoid such issues, a snapshot of the flags has to be taken prior to
using them. Some places already use READ_ONCE() for that, others do not.
Convert them all to the new flag accessor helpers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211129130653.2037928-6-mark.rutland@arm.com
|
|
Drop "support" for guest callbacks from architectures that don't implement
the guest callbacks. Future patches will convert the callbacks to
static_call; rather than churn a bunch of arch code (that was presumably
copy+pasted from x86), remove it wholesale as it's useless and at best
wasting cycles.
A future patch will also add a Kconfig to force architcture to opt into
the callbacks to make it more difficult for uses "support" to sneak in in
the future.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lore.kernel.org/r/20211111020738.2512932-6-seanjc@google.com
|
|
Protect perf_guest_cbs with RCU to fix multiple possible errors. Luckily,
all paths that read perf_guest_cbs already require RCU protection, e.g. to
protect the callback chains, so only the direct perf_guest_cbs touchpoints
need to be modified.
Bug #1 is a simple lack of WRITE_ONCE/READ_ONCE behavior to ensure
perf_guest_cbs isn't reloaded between a !NULL check and a dereference.
Fixed via the READ_ONCE() in rcu_dereference().
Bug #2 is that on weakly-ordered architectures, updates to the callbacks
themselves are not guaranteed to be visible before the pointer is made
visible to readers. Fixed by the smp_store_release() in
rcu_assign_pointer() when the new pointer is non-NULL.
Bug #3 is that, because the callbacks are global, it's possible for
readers to run in parallel with an unregisters, and thus a module
implementing the callbacks can be unloaded while readers are in flight,
resulting in a use-after-free. Fixed by a synchronize_rcu() call when
unregistering callbacks.
Bug #1 escaped notice because it's extremely unlikely a compiler will
reload perf_guest_cbs in this sequence. perf_guest_cbs does get reloaded
for future derefs, e.g. for ->is_user_mode(), but the ->is_in_guest()
guard all but guarantees the consumer will win the race, e.g. to nullify
perf_guest_cbs, KVM has to completely exit the guest and teardown down
all VMs before KVM start its module unload / unregister sequence. This
also makes it all but impossible to encounter bug #3.
Bug #2 has not been a problem because all architectures that register
callbacks are strongly ordered and/or have a static set of callbacks.
But with help, unloading kvm_intel can trigger bug #1 e.g. wrapping
perf_guest_cbs with READ_ONCE in perf_misc_flags() while spamming
kvm_intel module load/unload leads to:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP
CPU: 6 PID: 1825 Comm: stress Not tainted 5.14.0-rc2+ #459
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:perf_misc_flags+0x1c/0x70
Call Trace:
perf_prepare_sample+0x53/0x6b0
perf_event_output_forward+0x67/0x160
__perf_event_overflow+0x52/0xf0
handle_pmi_common+0x207/0x300
intel_pmu_handle_irq+0xcf/0x410
perf_event_nmi_handler+0x28/0x50
nmi_handle+0xc7/0x260
default_do_nmi+0x6b/0x170
exc_nmi+0x103/0x130
asm_exc_nmi+0x76/0xbf
Fixes: 39447b386c84 ("perf: Enhance perf to allow for guest statistic collection from host")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211111020738.2512932-2-seanjc@google.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Convert /reserved-memory bindings to schemas
- Convert a bunch of NFC bindings to schemas
- Convert bindings to schema: Xilinx USB, Freescale DDR controller, Arm
CCI-400, UBlox Neo-6M, 1-Wire GPIO, MSI controller, ASpeed LPC, OMAP
and Inside-Secure HWRNG, register-bit-led, OV5640, Silead GSL1680,
Elan ekth3000, Marvell bluetooth, TI wlcore, TI bluetooth, ESP
ESP8089, tlm,trusted-foundations, Microchip cap11xx, Ralink SoCs and
boards, and TI sysc
- New binding schemas for: msi-ranges, Aspeed UART routing controller,
palmbus, Xylon LogiCVC display controller, Mediatek's MT7621 SDRAM
memory controller, and Apple M1 PCIe host
- Run schema checks for %.dtb targets
- Improve build time when using DT_SCHEMA_FILES
- Improve error message when dtschema is not found
- Various doc reference fixes in MAINTAINERS
- Convert architectures to common CPU h/w ID parsing function
of_get_cpu_hwid().
- Allow for empty NUMA node IDs which may be hotplugged
- Cleanup of __fdt_scan_reserved_mem()
- Constify device_node parameters
- Update dtc to upstream v1.6.1-19-g0a3a9d3449c8. Adds new checks
'node_name_vs_property_name' and 'interrupt_map'.
- Enable dtc 'unit_address_format' warning by default
- Fix unittest EXPECT text for gpio hog errors
* tag 'devicetree-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (97 commits)
dt-bindings: net: ti,bluetooth: Document default max-speed
dt-bindings: pci: rcar-pci-ep: Document r8a7795
dt-bindings: net: qcom,ipa: IPA does support up to two iommus
of/fdt: Remove of_scan_flat_dt() usage for __fdt_scan_reserved_mem()
of: unittest: document intentional interrupt-map provider build warning
of: unittest: fix EXPECT text for gpio hog errors
of/unittest: Disable new dtc node_name_vs_property_name and interrupt_map warnings
scripts/dtc: Update to upstream version v1.6.1-19-g0a3a9d3449c8
dt-bindings: arm: firmware: tlm,trusted-foundations: Convert txt bindings to yaml
dt-bindings: display: tilcd: Fix endpoint addressing in example
dt-bindings: input: microchip,cap11xx: Convert txt bindings to yaml
dt-bindings: ufs: exynos-ufs: add exynosautov9 compatible
dt-bindings: ufs: exynos-ufs: add io-coherency property
dt-bindings: mips: convert Ralink SoCs and boards to schema
dt-bindings: display: xilinx: Fix example with psgtr
dt-bindings: net: nfc: nxp,pn544: Convert txt bindings to yaml
dt-bindings: Add a help message when dtschema tools are missing
dt-bindings: bus: ti-sysc: Update to use yaml binding
dt-bindings: sram: Allow numbers in sram region node name
dt-bindings: display: Document the Xylon LogiCVC display controller
...
|
|
Pull ARM updates from Russell King:
- Rejig task/thread info to place thread info in task struct
- Amba bus cleanups (removing unused functions)
- Handle Amba device probe without IRQ domains
- Parse linux,usable-memory-range in decompressor
- Mark OCRAM as read-only after initialisation
- Refactor page fault handling
- Fix PXN handling with LPAE kernels
- Warning and build fixes from Arnd
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
ARM: 9151/1: Thumb2: avoid __builtin_thread_pointer() on Clang
ARM: 9150/1: Fix PID_IN_CONTEXTIDR regression when THREAD_INFO_IN_TASK=y
ARM: 9147/1: add printf format attribute to early_print()
ARM: 9146/1: RiscPC needs older gcc version
ARM: 9145/1: patch: fix BE32 compilation
ARM: 9144/1: forbid ftrace with clang and thumb2_kernel
ARM: 9143/1: add CONFIG_PHYS_OFFSET default values
ARM: 9142/1: kasan: work around LPAE build warning
ARM: 9140/1: allow compile-testing without machine record
ARM: 9137/1: disallow CONFIG_THUMB with ARMv4
ARM: 9136/1: ARMv7-M uses BE-8, not BE-32
ARM: 9135/1: kprobes: address gcc -Wempty-body warning
ARM: 9101/1: sa1100/assabet: convert LEDs to gpiod APIs
ARM: 9131/1: mm: Fix PXN process with LPAE feature
ARM: 9130/1: mm: Provide die_kernel_fault() helper
ARM: 9126/1: mm: Kill page table base print in show_pte()
ARM: 9127/1: mm: Cleanup access_error()
ARM: 9129/1: mm: Kill task_struct argument for __do_page_fault()
ARM: 9128/1: mm: Refactor the __do_page_fault()
ARM: imx6: mark OCRAM mapping read-only
...
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- kprobes: Restructured stack unwinder to show properly on x86 when a
stack dump happens from a kretprobe callback.
- Fix to bootconfig parsing
- Have tracefs allow owner and group permissions by default (only
denying others). There's been pressure to allow non root to tracefs
in a controlled fashion, and using groups is probably the safest.
- Bootconfig memory managament updates.
- Bootconfig clean up to have the tools directory be less dependent on
changes in the kernel tree.
- Allow perf to be traced by function tracer.
- Rewrite of function graph tracer to be a callback from the function
tracer instead of having its own trampoline (this change will happen
on an arch by arch basis, and currently only x86_64 implements it).
- Allow multiple direct trampolines (bpf hooks to functions) be batched
together in one synchronization.
- Allow histogram triggers to add variables that can perform
calculations against the event's fields.
- Use the linker to determine architecture callbacks from the ftrace
trampoline to allow for proper parameter prototypes and prevent
warnings from the compiler.
- Extend histogram triggers to key off of variables.
- Have trace recursion use bit magic to determine preempt context over
if branches.
- Have trace recursion disable preemption as all use cases do anyway.
- Added testing for verification of tracing utilities.
- Various small clean ups and fixes.
* tag 'trace-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (101 commits)
tracing/histogram: Fix semicolon.cocci warnings
tracing/histogram: Fix documentation inline emphasis warning
tracing: Increase PERF_MAX_TRACE_SIZE to handle Sentinel1 and docker together
tracing: Show size of requested perf buffer
bootconfig: Initialize ret in xbc_parse_tree()
ftrace: do CPU checking after preemption disabled
ftrace: disable preemption when recursion locked
tracing/histogram: Document expression arithmetic and constants
tracing/histogram: Optimize division by a power of 2
tracing/histogram: Covert expr to const if both operands are constants
tracing/histogram: Simplify handling of .sym-offset in expressions
tracing: Fix operator precedence for hist triggers expression
tracing: Add division and multiplication support for hist triggers
tracing: Add support for creating hist trigger variables from literal
selftests/ftrace: Stop tracing while reading the trace file by default
MAINTAINERS: Update KPROBES and TRACING entries
test_kprobes: Move it from kernel/ to lib/
docs, kprobes: Remove invalid URL and add new reference
samples/kretprobes: Fix return value if register_kretprobe() failed
lib/bootconfig: Fix the xbc_get_info kerneldoc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Thomas Gleixner:
- Revert the printk format based wchan() symbol resolution as it can
leak the raw value in case that the symbol is not resolvable.
- Make wchan() more robust and work with all kind of unwinders by
enforcing that the task stays blocked while unwinding is in progress.
- Prevent sched_fork() from accessing an invalid sched_task_group
- Improve asymmetric packing logic
- Extend scheduler statistics to RT and DL scheduling classes and add
statistics for bandwith burst to the SCHED_FAIR class.
- Properly account SCHED_IDLE entities
- Prevent a potential deadlock when initial priority is assigned to a
newly created kthread. A recent change to plug a race between cpuset
and __sched_setscheduler() introduced a new lock dependency which is
now triggered. Break the lock dependency chain by moving the priority
assignment to the thread function.
- Fix the idle time reporting in /proc/uptime for NOHZ enabled systems.
- Improve idle balancing in general and especially for NOHZ enabled
systems.
- Provide proper interfaces for live patching so it does not have to
fiddle with scheduler internals.
- Add cluster aware scheduling support.
- A small set of tweaks for RT (irqwork, wait_task_inactive(), various
scheduler options and delaying mmdrop)
- The usual small tweaks and improvements all over the place
* tag 'sched-core-2021-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (69 commits)
sched/fair: Cleanup newidle_balance
sched/fair: Remove sysctl_sched_migration_cost condition
sched/fair: Wait before decaying max_newidle_lb_cost
sched/fair: Skip update_blocked_averages if we are defering load balance
sched/fair: Account update_blocked_averages in newidle_balance cost
x86: Fix __get_wchan() for !STACKTRACE
sched,x86: Fix L2 cache mask
sched/core: Remove rq_relock()
sched: Improve wake_up_all_idle_cpus() take #2
irq_work: Also rcuwait for !IRQ_WORK_HARD_IRQ on PREEMPT_RT
irq_work: Handle some irq_work in a per-CPU thread on PREEMPT_RT
irq_work: Allow irq_work_sync() to sleep if irq_work() no IRQ support.
sched/rt: Annotate the RT balancing logic irqwork as IRQ_WORK_HARD_IRQ
sched: Add cluster scheduler level for x86
sched: Add cluster scheduler level in core and related Kconfig for ARM64
topology: Represent clusters of CPUs within a die
sched: Disable -Wunused-but-set-variable
sched: Add wrapper for get_wchan() to keep task blocked
x86: Fix get_wchan() to support the ORC unwinder
proc: Use task_is_running() for wchan in /proc/$pid/stat
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core changes:
- Prevent a potential deadlock when initial priority is assigned to a
newly created interrupt thread. A recent change to plug a race
between cpuset and __sched_setscheduler() introduced a new lock
dependency which is now triggered. Break the lock dependency chain
by moving the priority assignment to the thread function.
- A couple of small updates to make the irq core RT safe.
- Confine the irq_cpu_online/offline() API to the only left unfixable
user Cavium Octeon so that it does not grow new usage.
- A small documentation update
Driver changes:
- A large cross architecture rework to move irq_enter/exit() into the
architecture code to make addressing the NOHZ_FULL/RCU issues
simpler.
- The obligatory new irq chip driver for Microchip EIC
- Modularize a few irq chip drivers
- Expand usage of devm_*() helpers throughout the driver code
- The usual small fixes and improvements all over the place"
* tag 'irq-core-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
h8300: Fix linux/irqchip.h include mess
dt-bindings: irqchip: renesas-irqc: Document r8a774e1 bindings
MIPS: irq: Avoid an unused-variable error
genirq: Hide irq_cpu_{on,off}line() behind a deprecated option
irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()
MIPS: loongson64: Drop call to irq_cpu_offline()
irq: remove handle_domain_{irq,nmi}()
irq: remove CONFIG_HANDLE_DOMAIN_IRQ_IRQENTRY
irq: riscv: perform irqentry in entry code
irq: openrisc: perform irqentry in entry code
irq: csky: perform irqentry in entry code
irq: arm64: perform irqentry in entry code
irq: arm: perform irqentry in entry code
irq: add a (temporary) CONFIG_HANDLE_DOMAIN_IRQ_IRQENTRY
irq: nds32: avoid CONFIG_HANDLE_DOMAIN_IRQ
irq: arc: avoid CONFIG_HANDLE_DOMAIN_IRQ
irq: add generic_handle_arch_irq()
irq: unexport handle_irq_desc()
irq: simplify handle_domain_{irq,nmi}()
irq: mips: simplify do_domain_IRQ()
...
|
