| Age | Commit message (Collapse) | Author |
|---|
|
Bindings expect pin configuration nodes in pinctrl to match certain
naming:
imx7s-colibri-eval-v3.dtb: pinctrl@30330000: 'lvdstx' does not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
imx7s-warp.dtb: pinctrl@30330000: 'usdhc3grp_100mhz', 'usdhc3grp_200mhz' do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is no "fsl,phy" property in pin controller pincfg nodes:
imx7d-zii-rmu2.dtb: pinctrl@302c0000: enet1phyinterruptgrp: 'fsl,pins' is a required property
imx7d-zii-rmu2.dtb: pinctrl@302c0000: enet1phyinterruptgrp: 'fsl,phy' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: f496e6750083 ("ARM: dts: Add ZII support for ZII i.MX7 RMU2 board")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The merge of imx-spdif driver into fsl-asoc-card brought
new DT properties that can be used with the "fsl,imx-audio-spdif"
compatible:
* The "spdif-controller" property from imx-spdif is named "audio-cpu"
in fsl-asoc-card.
* fsl-asoc-card uses codecs explicitly declared in DT
with "audio-codec".
With an S/PDIF, codec drivers spdif_transmitter and
spdif_receiver should be used.
Driver imx-spdif used instead the dummy codec and a pair of
boolean properties, "spdif-in" and "spdif-out".
While backward compatibility is kept to support properties
"spdif-controller", "spdif-in" and "spdif-out", using new properties has
several benefits:
* "audio-cpu" and "audio-codec" are more generic names reflecting
that the fsl-asoc-card driver supports multiple hardware.
They are properties already used by devices using the
fsl-asoc-card driver.
They are also similar to properties of simple-card: "cpu" and "codec".
* "spdif-in" and "spdif-out" imply the use of the dummy codec in the
driver. However, there are already two codec drivers for the S/PDIF,
spdif_transmitter and spdif_receiver.
It is better to declare S/PDIF Tx and Rx devices in a DT, and then
reference them with "audio-codec" than using the dummy codec.
For those reasons, this commit updates in-tree DTs to use the new
properties:
* Rename "spdif-controller" property to "audio-cpu".
* Declare S/PDIF transmitter and/or receiver devices, and use them with
the "audio-codec" property instead of "spdif-out" and/or "spdif-in".
These modifications were tested only on an imx8mn-evk board.
Note that out-of-tree and old DTs are still supported.
Signed-off-by: Elinor Montmasson <elinor.montmasson@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The regulator should not be placed under simple-bus.
Remove it from simple-bus to fix the following dt-schema warnings:
'regulators' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
regulators: #size-cells:0:0: 0 is not one of [1, 2]
regulators: regulator@0:reg:0: [0] is too short
regulators: 'ranges' is a required property
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use national,lm75a to specify exact variant used. This should cause
no functional changes.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable IIO hwmon support for ADC1 and ADC2. All channels are
available on X23 (ADC2) and X24 (ADC1) of MBa7x.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to fsl,imx-dma.yaml, the node name must be dma-controller.
Change it accordingly to fix the following dt-schema warnings:
'dma@10001000' does not match '^dma-controller(@.*)?$'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On the imx6dl-yapp4 revision based boards, the RGB LED is not driven
directly by the LP5562 driver but through FET transistors. Hence the LED
current is not determined by the driver but by the LED series resistors.
On the imx6dl-yapp43 revision based boards, we removed the FET transistors
to drive the LED directly from the LP5562 but forgot to tune the output
current to match the previous HW design.
Set the LED current on imx6dl-yapp43 based boards to the same values
measured on the imx6dl-yapp4 boards and limit the maximum current to 20mA.
Fixes: 7da4734751e0 ("ARM: dts: imx6dl-yapp43: Add support for new HW revision of the IOTA board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It's not necessary to split display0 node. Merge it to save two lines.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
SII9022 and TVE are connected with IPU DI0 and IPU DI1 respectively, so
they are in two different display pipelines and may run simultaneously.
Keep TVE being enabled as imx53-qsb-common.dtsi does by not setting it's
status property to "disabled".
Fixes: eeb403df953f ("ARM: dts: imx53-qsb: add support for the HDMI expander")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
By default, the ENET_REF is configured at 125MHz on i.MX6SX, which works
well for boards that operate in RGMII mode.
The imx6sx-udoo-neo has a KSZ8091 Ethernet PHY that is connected via
RMII interface, so a 50MHz ENET_REF clock is expected.
Describe the IMX6SX_CLK_ENET_REF accordingly.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX ARM device tree change for 6.11:
- A few changes from Krzysztof Kozlowski to fix dtschema issues
- A series from Michael Walle to improve kontron-samx6i SoM support by
fixing various errors and add kontron-samx6i-ads2 board
- Add LVDS port data mapping for M53 Menlo board
- Convert NVMEM usage to layout syntax on MBA6 boards
* tag 'imx-dt-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-kontron-samx6i: add actual device trees
ARM: dts: imx6qdl-kontron-samx6i: remove wake-up-gpio property
ARM: dts: imx6qdl-kontron-samx6i: fix PCIe reset polarity
ARM: dts: imx6qdl-kontron-samx6i: fix node names
ARM: dts: imx6qdl-kontron-samx6i: add SDIO_PWR_EN support
ARM: dts: imx6qdl-kontron-samx6i: always enable eMMC
ARM: dts: imx6qdl-kontron-samx6i: fix product name
ARM: dts: imx6qdl-kontron-samx6i: fix SPI0 chip selects
ARM: dts: imx6qdl-kontron-samx6i: cleanup the PMIC node
ARM: dts: imx6qdl-kontron-samx6i: fix board reset
ARM: dts: imx6qdl-kontron-samx6i: fix PHY reset
ARM: dts: imx6qdl-kontron-samx6i: fix phy-mode
ARM: dts: nxp: imx6: convert NVMEM content to layout syntax
ARM: dts: e60k02: fix aliases for mmc
ARM: dts: imx: Add LVDS port data mapping on M53 Menlo
ARM: dts: imx28-tx28: drop redundant 'panel-name' property
ARM: dts: imx: drop redundant 'u-boot,panel-name' property
ARM: dts: imx6dl-aristainetos2_4: drop redundant 'power-on-delay' property
ARM: dts: imx: correct choice of panel native mode
ARM: dts: imx: align panel timings node name with dtschema
Link: https://lore.kernel.org/r/20240702142153.413061-3-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
For now, there wasn't any in-tree users of the dtsi files for the
Kontron SMARC-sAMX6i board. Let's add device trees, for this board on a
Kontron SMARC Eval 2.0 Carrier.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the "wake-up-gpio" property within the PCIe controller node.
There is no such property, thus just remove it. This will also make the
schema validation happy.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PCIe reset line is active low. Fix it.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename the nodes according to the schema. In particular, rename the bit
bang I2C controller to "i2c-N" and the mux nodes of the audmux to
"mux-*". While at it, fix the typo "adu", which should have been "aud".
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The module can enable/disable the SD card power supply and has
it's dedicated pin SDIO_PWR_EN for that reason. This is esp.
useful to be able to reset the SD card if it was in an UHS mode.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are no variants of this module without an eMMC.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The correct name of the product is "Kontron SMARC-sAMX6i". See also
https://www.kontron.com/en/products/smarc-samx6i/p89810
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the comment, remove the unused phandle name for the
VGEN5 output. VGEN5 is not used at all.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX6 cannot add any RGMII delays. The PHY has to add both the RX
and TX delays on the RGMII interface. Fix the interface mode. While at
it, use the new phy-connection-type property name.
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use cleaner (and non-deprecated) bindings syntax. See commit
bd912c991d2e ("dt-bindings: nvmem: layouts: add fixed-layout") for
details.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit fa2d0aa96941
("mmc: core: Allow setting slot index via device tree alias")
mmc numbering are changed, confusing boot scripts. Fix that by adding
proper aliases
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Describe LVDS data mapping of the LVDS-to-DPI decoder input port.
This fixes a warning reported by lvds-codec driver:
"
lvds-codec lvds-decoder: missing 'data-mapping' DT property
"
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We cannot use /delete-node/ directive to delete a node in a DT
overlay. The node won't be deleted effectively. Instead, set
the node's status property to "disabled" to achieve something
similar.
Fixes: eeb403df953f ("ARM: dts: imx53-qsb: add support for the HDMI expander")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Panel timing bindings do not allow 'panel-name' and there seems to be no
users of it: neither Linux kernel drivers, nor U-boot as of
v2024.07-rc2.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Panel timing bindings do not allow 'u-boot,panel-name' and there seems
to be no users of it: neither Linux kernel drivers, nor U-boot as of
v2024.07-rc2. Reported by dtbs_check:
imx6qp-tx6qp-8037.dtb: display-timings: timing-et0700: 'u-boot,panel-name' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
LG4573 panel bindings do not allow 'power-on-delay' property. Linux
driver does not use it, either. Reported by dtbs_check:
imx6dl-aristainetos2_4.dtb: display@0: Unevaluated properties are not allowed ('power-on-delay' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Bindings and Linux driver expect native-mode to be a phandle to one of
the timings node, not a boolean property. Correct the DTS to fix
dtbs_check warnings like:
imx53-m53evk.dtb: display-timings: timing-800x480p60: 'native-mode' does not match any of the regexes: 'pinctrl-[0-9]+'
This should not have actual effect for Linux kernel (no real bug
affecting choice of native-mode), because the first timing node is
chosen in absence of proper native-mode property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
DT schema expects panel timings node to follow certain pattern,
dtbs_check warnings:
imx6dl-gw54xx.dtb: display-timings: 'hsd100pxn1' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
Linux drivers do not care about node name, so this should not have
effect on Linux.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull SoC devicetree updates from Arnd Bergmann:
"The updates this time are a bit smaller than most times, mainly
because it is not totally dominated by new Qualcomm hardware support.
Instead, we larger than average updates for Rockchips, NXP, Allwinner
and TI. The only two new SoCs this time are both from NXP and are
minor variants of already supported ones.
The updates for aspeed, amlogic and mediatek came a little late, so
I'm saving those for part 2 in a few days if everything turns out
fine.
New machines this time contain:
- two Broadcom SoC based wireless routers from Asus
- Five allwinner based consumer devices for gaming, set-top-box and
eboot reader applications
- Three older phones based on Qualcomm chips, plus the more recent
Sony Xperia 1 V
- 14 industrial and embedded boards based on NXP i.MX6, i.MX8,
layerscape and s32g3 SoCs
- six rockchips boards including another handheld game console and a
few single-board computers
On top of these, we have the usual cleanups for dtc warnings and
updates to add more features to already merged machines"
* tag 'soc-dt-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (612 commits)
arm64: dts: marvell: espressobin-ultra: fix Ethernet Switch unit address
arm64: dts: marvell: turris-mox: drop unneeded flash address/size-cells
arm64: dts: marvell: eDPU: drop redundant address/size-cells
arm64: dts: qcom: pm6150: correct USB VBUS regulator compatible
arm64: dts: rockchip: add rk3588 pcie and php IOMMUs
arm64: dts: rockchip: enable onboard spi flash for rock-3a
arm64: dts: rockchip: add USB-C support to rk3588s-orangepi-5
arm64: dts: rockchip: Enable GPU on Orange Pi 5
arm64: dts: rockchip: enable GPU on khadas-edge2
arm64: dts: rockchip: Add USB3 on Edgeble NCM6A-IO board
arm64: dts: rockchip: Support poweroff on Edgeble Neural Compute Module
arm64: dts: rockchip: Add Radxa ROCK 3C
dt-bindings: arm: rockchip: add Radxa ROCK 3C
arm64: dts: exynos: gs101: specify empty clocks for remaining pinctrl
arm64: dts: exynos: gs101: specify bus clock for pinctrl_hsi2
arm64: dts: exynos: gs101: specify bus clock for pinctrl_peric[01]
arm64: dts: exynos: gs101: specify bus clock for pinctrl (far) alive
arm64: dts: Add/fix /memory node unit-addresses
arm64: dts: qcom: qcs404: fix bluetooth device address
arm64: dts: qcom: sc8280xp-x13s: enable USB MP and fingerprint reader
...
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warnings:
arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6ul-pico-hobbit.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6ul-pico-pi.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warnings:
arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6ull-kontron-bl.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dtb: pwm@20f8000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warnings:
arch/arm/boot/dts/nxp/imx/imx6ul-isiot-emmc.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6ul-isiot-nand.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warnings:
arch/arm/boot/dts/nxp/imx/imx6ul-opos6uldev.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6ull-opos6uldev.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6ul-geam.dtb: pwm@20fc000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dtb: pwm@20f0000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warnings:
arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6ull-14x14-evk.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6ulz-14x14-evk.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warnings:
arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dtb: pwm@22a8000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
There is no need for an explicit status = "okay" in the pwm nodes as
the soc dtsi doesn't disable these devices. Drop these properties, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warnings:
arch/arm/boot/dts/nxp/imx/imx6sx-sdb-reva.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6sx-sdb-sai.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
arch/arm/boot/dts/nxp/imx/imx6sx-sdb-mqs.dtb: pwm@2088000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
There is no need for an explicit status = "okay" in the pwm node as
the soc dtsi doesn't disable this device. Drop this property, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dtb: pwm@208c000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
There is no need for an explicit status = "okay" in the pwm node as
the soc dtsi doesn't disable this device. Drop this property, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6sll-evk.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
There is no need for an explicit status = "okay" in the pwm node as
the soc dtsi doesn't disable this device. Drop this property, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6sl-evk.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
There is no need for an explicit status = "okay" in the pwm node as
the soc dtsi doesn't disable these devices. Drop this property, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dtb: pwm@2084000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The binding dictates using 3 pwm-cells. Adhere to that.
This fixes the following dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dtb: pwm@2080000: #pwm-cells:0:0: 3 was expected
from schema : http://devicetree.org/schemas/pwm/imx-pwm.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
