| Age | Commit message (Collapse) | Author |
|---|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner fixes for 6.16
Only one fix:
Correct the name of the A523's EMAC0 to GMAC0, as seen in the SoC's
datasheets. The matching DT binding change is in the net tree.
* tag 'sunxi-fixes-for-6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a523: Rename emac0 to gmac0
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When the chip is not powered on correctly (like during driver
development) rtw89_fwdl_check_path_ready_ax() can fail.
read_poll_timeout_atomic() with a delay of 1 µs and a timeout of
400000 µs can take 50 seconds with USB because of the time it takes to
send a USB control message. The firmware upload is tried 5 times, so
in total it takes 250 seconds.
Lower the timeout to 3200 for USB in order to reduce the time
rtw89_fwdl_check_path_ready_ax() takes from 50 seconds to less than 1
second.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/af0b25d0-ea67-455e-91f2-8e4c18ae4328@gmail.com
|
|
This read_poll_timeout_atomic() with a delay of 1 µs and a timeout of
1000000 µs can take ~250 seconds in the worst case because sending a
USB control message takes ~250 µs.
Lower the timeout to 4000 for USB in order to reduce the maximum polling
time to ~1 second.
This problem was observed with RTL8851BU while suspending to RAM with
WOWLAN enabled. The computer sat for 4 minutes with a black screen
before suspending.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/09313da6-c865-4e91-b758-4cb38a878796@gmail.com
|
|
The variable 'path' from rtw89_phy_get_syn_sel() as index of array could
be 3, but array size is 2. Fortunately, current chip->rf_path_num is
smaller or equal to 2, so it is safe. To prevent mistakes in the future,
add a checking and avoid Coverity warnings.
Addresses-Coverity-ID: linux-next: 1644716 ("Out-of-bounds write")
Addresses-Coverity-ID: linux-next: 1644717 ("Out-of-bounds write")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250715035259.45061-6-pkshih@realtek.com
|
|
The queued and obsoleted scan events can be wrongly treated as events of
new scan request, causing unexpected scan result. Attach a software
sequence number to scan request and its corresponding events. When a new
scan request is acknowledged by firmware, purge the scan events if its
sequence number is not belong to current request.
Normal case:
mac80211 event work event BH
------------- ---------- --------
scan req #1 ---->o
|
<----o <...........................o
o
|
<--------------------------+
ieee80211_scan_completed()
Abnormal case (late event work):
mac80211 event work event BH
------------- ---------- --------
scan req #1 ---->o
|
<----o <...........................o
o #1
scan cancel #2 ->o
|
<----o <...........................o
o #2
| (patch to avoid this)
scan req #3 ---->o |
| |
<----o <..........|................o
| o #3
<--------------------------+
ieee80211_scan_completed()
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250715035259.45061-5-pkshih@realtek.com
|
|
When the 'Disabled Subchannel Bitmap' within the EHT Operation
element is changed, mac80211 parse and pass it to the driver.
The driver is then updated with this puncturing bitmap to
optimize bandwidth usage and prevent interference from
degrading performance across the entire channel.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250715035259.45061-4-pkshih@realtek.com
|
|
Since the RX counter in the PPDU status is not used,
it is disabled to reduce the waste of DLE quota.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250715035259.45061-3-pkshih@realtek.com
|
|
In order for the situation where the dispatcher blocking
causes HAXIDMA to be unable to TX to be reported as
a TX stuck, so that subsequent recovery can be handled.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250715035259.45061-2-pkshih@realtek.com
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Driver Changes:
- SR-IOV fixes for GT reset and TLB invalidation
- Fix memory copy direction during migration
- Fix alignment check on migration
- Fix MOCS and page fault init order to correctly
account for topology
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/6jworkgupwstm4v7aohbuzod3dyz4u7pyfhshr5ifgf2xisgj3@cm5em5yupjiu
|
|
We observed a regression in our customer’s environment after enabling
CONFIG_LAZY_RCU. In the Android Update Engine scenario, where ioctl() is
used heavily, we found that callbacks queued via call_rcu_hurry (such as
percpu_ref_switch_to_atomic_rcu) can sometimes be delayed by up to 5
seconds before execution. This occurs because the new grace period does
not start immediately after the previous one completes.
The root cause is that the wake_nocb_gp_defer() function now checks
"rdp->nocb_defer_wakeup" instead of "rdp_gp->nocb_defer_wakeup". On CPUs
that are not rcuog, "rdp->nocb_defer_wakeup" may always be
RCU_NOCB_WAKE_NOT. This can cause "rdp_gp->nocb_defer_wakeup" to be
downgraded and the "rdp_gp->nocb_timer" to be postponed by up to 10
seconds, delaying the execution of hurry RCU callbacks.
The trace log of one scenario we encountered is as follow:
// previous GP ends at this point
rcu_preempt [000] d..1. 137.240210: rcu_grace_period: rcu_preempt 8369 end
rcu_preempt [000] ..... 137.240212: rcu_grace_period: rcu_preempt 8372 reqwait
// call_rcu_hurry enqueues "percpu_ref_switch_to_atomic_rcu", the callback waited on by UpdateEngine
update_engine [002] d..1. 137.301593: __call_rcu_common: wyy: unlikely p_ref = 00000000********. lazy = 0
// FirstQ on cpu 2 rdp_gp->nocb_timer is set to fire after 1 jiffy (4ms)
// and the rdp_gp->nocb_defer_wakeup is set to RCU_NOCB_WAKE
update_engine [002] d..2. 137.301595: rcu_nocb_wake: rcu_preempt 2 FirstQ on cpu2 with rdp_gp (cpu0).
// FirstBQ event on cpu2 during the 1 jiffy, make the timer postpond 10 seconds later.
// also, the rdp_gp->nocb_defer_wakeup is overwrite to RCU_NOCB_WAKE_LAZY
update_engine [002] d..1. 137.301601: rcu_nocb_wake: rcu_preempt 2 WakeEmptyIsDeferred
...
...
...
// before the 10 seconds timeout, cpu0 received another call_rcu_hurry
// reset the timer to jiffies+1 and set the waketype = RCU_NOCB_WAKE.
kworker/u32:0 [000] d..2. 142.557564: rcu_nocb_wake: rcu_preempt 0 FirstQ
kworker/u32:0 [000] d..1. 142.557576: rcu_nocb_wake: rcu_preempt 0 WakeEmptyIsDeferred
kworker/u32:0 [000] d..1. 142.558296: rcu_nocb_wake: rcu_preempt 0 WakeNot
kworker/u32:0 [000] d..1. 142.558562: rcu_nocb_wake: rcu_preempt 0 WakeNot
// idle(do_nocb_deferred_wakeup) wake rcuog due to waketype == RCU_NOCB_WAKE
<idle> [000] d..1. 142.558786: rcu_nocb_wake: rcu_preempt 0 DoWake
<idle> [000] dN.1. 142.558839: rcu_nocb_wake: rcu_preempt 0 DeferredWake
rcuog/0 [000] ..... 142.558871: rcu_nocb_wake: rcu_preempt 0 EndSleep
rcuog/0 [000] ..... 142.558877: rcu_nocb_wake: rcu_preempt 0 Check
// finally rcuog request a new GP at this point (5 seconds after the FirstQ event)
rcuog/0 [000] d..2. 142.558886: rcu_grace_period: rcu_preempt 8372 newreq
rcu_preempt [001] d..1. 142.559458: rcu_grace_period: rcu_preempt 8373 start
...
rcu_preempt [000] d..1. 142.564258: rcu_grace_period: rcu_preempt 8373 end
rcuop/2 [000] D..1. 142.566337: rcu_batch_start: rcu_preempt CBs=219 bl=10
// the hurry CB is invoked at this point
rcuop/2 [000] b.... 142.566352: blk_queue_usage_counter_release: wyy: wakeup. p_ref = 00000000********.
This patch changes the condition to check "rdp_gp->nocb_defer_wakeup" in
the lazy path. This prevents an already scheduled "rdp_gp->nocb_timer"
from being postponed and avoids overwriting "rdp_gp->nocb_defer_wakeup"
when it is not RCU_NOCB_WAKE_NOT.
Fixes: 3cb278e73be5 ("rcu: Make call_rcu() lazy to save power")
Co-developed-by: Cheng-jui Wang <cheng-jui.wang@mediatek.com>
Signed-off-by: Cheng-jui Wang <cheng-jui.wang@mediatek.com>
Co-developed-by: Lorry.Luo@mediatek.com
Signed-off-by: Lorry.Luo@mediatek.com
Tested-by: weiyangyang@vivo.com
Signed-off-by: weiyangyang@vivo.com
Signed-off-by: Tze-nan Wu <Tze-nan.Wu@mediatek.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Neeraj Upadhyay (AMD) <neeraj.upadhyay@kernel.org>
|
|
There was a lot of common code in the codepaths used to convert an
inline directory and to creaet a new directory. To address this,
rename ext4_init_dot_dotdot() to ext4_init_dirblock() and then move
common code into that function.
This reduces the lines of code count in fs/ext4/inline.c and
fs/ext4/namei.c, as well as reducing the size of their object files.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://patch.msgid.link/20250712181249.434530-3-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
The strcpy() function is considered dangerous and eeeevil by people
who are using sophisticated code analysis tools such as "grep". This
is true even when a quick inspection would show that the source is a
constant string ("." or "..") and the destination is a fixed array
which is guaranteed to have enough space. Make the "grep" code
analysis tool happy by using memcpy() isstead of strcpy(). :-)
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://patch.msgid.link/20250712181249.434530-2-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
In a discussion over a proposed patch, "ext4: replace strcpy() with
'.' assignment"[1], I had asserted that directory entries in ext4 were
not NUL terminated, and hence it was safe to replace strcpy() with a
direct assignment. As it turns out, this was incorrect. It's true
for all all directory entries *except* for '.' and '..' where the
kernel was using strcmp() and where e2fsck actually checks and offers
to fix things if '.' and '..' are not NUL terminated.
[1] https://lore.kernel.org/r/202505191316.JJMnPobO-lkp@intel.com
We can't change this without breaking old kernel versions, but in the
spirit of "be liberal in what you receive", use direct comparison of
de->name_len and de->name[0,1] instead of strcmp(). This has the side
benefit of reducing the compiled text size by 96 bytes on x86_64.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://patch.msgid.link/20250712181249.434530-1-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Currently we clear BH_New bit in case of error and also in the standard
ext4_write_end() handler (in block_commit_write()). However
ext4_journalled_write_end() misses this clearing and thus we are leaving
stale BH_New bits behind. Generally ext4_block_write_begin() clears
these bits before any harm can be done but in case blocksize < pagesize
and we hit some error when processing a page with these stale bits,
we'll try to zero buffers with these stale BH_New bits and jbd2 will
complain (as buffers were not prepared for writing in this transaction).
Fix the problem by clearing BH_New bits in ext4_journalled_write_end()
and WARN if ext4_block_write_begin() sees stale BH_New bits.
Reported-by: Baolin Liu <liubaolin12138@163.com>
Reported-by: Zhi Long <longzhi@sangfor.com.cn>
Fixes: 3910b513fcdf ("ext4: persist the new uptodate buffers in ext4_journalled_zero_new_buffers")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250709084831.23876-2-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
In ext4_io_end_defer_completion(), check if io_end->list_vec is empty to
avoid adding an io_end that requires no conversion to the
i_rsv_conversion_list, which in turn prevents starting an unnecessary
worker. An ext4_emergency_state() check is also added to avoid attempting
to abort the journal in an emergency state.
Additionally, ext4_put_io_end_defer() is refactored to call
ext4_io_end_defer_completion() directly instead of being open-coded.
This also prevents starting an unnecessary worker when EXT4_IO_END_FAILED
is set but data_err=abort is not enabled.
This ensures that the check in ext4_put_io_end_defer() is consistent with
the check in ext4_end_bio(). Otherwise, we might add an io_end to the
i_rsv_conversion_list and then call ext4_finish_bio(), after which the
inode could be freed before ext4_end_io_rsv_work() is called, triggering
a use-after-free issue.
Fixes: ce51afb8cc5e ("ext4: abort journal on data writeback failure if in data_err=abort mode")
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250708111504.3208660-1-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Initial __arena global variable support implementation in libbpf
contains a bug: it remembers struct bpf_map pointer for arena, which is
used later on to process relocations. Recording this pointer is
problematic because map pointers are not stable during ELF relocation
collection phase, as an array of struct bpf_map's can be reallocated,
invalidating all the pointers. Libbpf is dealing with similar issues by
using a stable internal map index, though for BPF arena map specifically
this approach wasn't used due to an oversight.
The resulting behavior is non-deterministic issue which depends on exact
layout of ELF object file, number of actual maps, etc. We didn't hit
this until very recently, when this bug started triggering crash in BPF
CI when validating one of sched-ext BPF programs.
The fix is rather straightforward: we just follow an established pattern
of remembering map index (just like obj->kconfig_map_idx, for example)
instead of `struct bpf_map *`, and resolving index to a pointer at the
point where map information is necessary.
While at it also add debug-level message for arena-related relocation
resolution information, which we already have for all other kinds of
maps.
Fixes: 2e7ba4f8fd1f ("libbpf: Recognize __arena global variables.")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Tested-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20250718001009.610955-1-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-fixes
Mediatek DRM Fixes - 20250718
1. Add wait_event_timeout when disabling plane
2. only announce AFBC if really supported
3. mtk_dpi: Reorder output formats on MT8195/88
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20250717232916.12372-1-chunkuang.hu@kernel.org
|
|
The DMA map functions can fail and should be tested for errors.
If the mapping fails, unmap and return an error.
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250716094733.28734-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The DMA map functions can fail and should be tested for errors.
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250716095733.37452-3-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for IPv6 environment for napi_id test.
Test Plan:
./run_kselftest.sh -t drivers/net:napi_id.py
TAP version 13
1..1
# timeout set to 45
# selftests: drivers/net: napi_id.py
# TAP version 13
# 1..1
# ok 1 napi_id.test_napi_id
# # Totals: pass:1 fail:0 xfail:0 xpass:0 skip:0 error:0
ok 1 selftests: drivers/net: napi_id.py
Signed-off-by: Tianyi Cui <1997cui@gmail.com>
Link: https://patch.msgid.link/20250717011913.1248816-1-1997cui@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VNIC testing on multi-core Power systems showed SAR stats drift
and packet rate inconsistencies under load.
Implements ndo_get_stats64 to provide safe aggregation of queue-level
atomic64 counters into rtnl_link_stats64 for use by tools like 'ip -s',
'ifconfig', and 'sar'. Switch to ndo_get_stats64 to align SAR reporting
with the standard kernel interface for retrieving netdev stats.
This removes redundant per-adapter stat updates, reduces overhead,
eliminates cacheline bouncing from hot path updates, and improves
the accuracy of reported packet rates.
Signed-off-by: Mingming Cao <mmc@linux.ibm.com>
Reviewed-by: Brian King <bjking1@linux.ibm.com>
Reviewed-by: Dave Marquardt <davemarq@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
----
Changes since v3:
link to v3: https://www.spinics.net/lists/netdev/msg1107999.html
-- keep per queue counters as u64 (this patch) and drop off patch 1 in v3
Link: https://patch.msgid.link/20250716152115.61143-1-mmc@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tariq Toukan says:
====================
net/mlx5: misc changes 2025-07-16
This series contains misc enhancements to the mlx5 driver.
v1: https://lore.kernel.org/1752471585-18053-1-git-send-email-tariqt@nvidia.com
====================
Link: https://patch.msgid.link/1752675472-201445-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
qdisc_sleeping variable is declared as "struct Qdisc __rcu" and
as such needs proper annotation while accessing it.
Without rtnl_dereference(), the following error is generated by sparse:
drivers/net/ethernet/mellanox/mlx5/core/en/qos.c:377:40: warning:
incorrect type in initializer (different address spaces)
drivers/net/ethernet/mellanox/mlx5/core/en/qos.c:377:40: expected
struct Qdisc *qdisc
drivers/net/ethernet/mellanox/mlx5/core/en/qos.c:377:40: got struct
Qdisc [noderef] __rcu *qdisc_sleeping
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1752675472-201445-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the following kdoc warning:
git ls-files *.[ch] | egrep drivers/net/ethernet/mellanox/mlx5/core/ |\
xargs scripts/kernel-doc --none
drivers/net/ethernet/mellanox/mlx5/core/eswitch.h:824: warning: cannot
understand function prototype: 'struct mlx5_esw_event_info '
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1752675472-201445-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPSec hardware offload in legacy mode should not be affected by the
steering mode, hence it should also work properly with hmfs mode.
Remove steering mode validation when calculating the cap for packet
offload, this will also enable the missing cap MLX5_IPSEC_CAP_PRIO
needed for crypto offload.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1752675472-201445-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.16-2025-07-17:
amdgpu:
- Fix a DC memory leak
- DCN 4.0.1 degamma LUT fix
- Fix reset counter handling for soft recovery
- GC 8 fix
radeon:
- Drop console locks when suspending/resuming
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250717171935.642380-1-alexander.deucher@amd.com
|
|
readl() returns 32-bit value but Clause 22/45 registers are 16-bit wide.
Masking with 0xFFFF avoids using garbage upper bits.
Signed-off-by: Jack Ping CHNG <jchng@maxlinear.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250716030349.3796806-1-jchng@maxlinear.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The __esw_qos_alloc_node() function returns NULL on error. It doesn't
return error pointers. Update the error checking to match.
Fixes: 96619c485fa6 ("net/mlx5: Add support for setting tc-bw on nodes")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/0ce4ec2a-2b5d-4652-9638-e715a99902a7@sabinyo.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We recently changed this from using devm_ioremap() to using
devm_ioremap_resource() and unfortunately the former returns NULL while
the latter returns error pointers. The check for errors needs to be
updated as well.
Fixes: e27dba1951ce ("net: Use of_reserved_mem_region_to_resource{_byname}() for "memory-region"")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/87c10dbd-df86-4971-b4f5-40ba02c076fb@sabinyo.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The devm_ioremap_resource() function returns error pointers. It never
returns NULL. Update the check to match.
Fixes: e27dba1951ce ("net: Use of_reserved_mem_region_to_resource{_byname}() for "memory-region"")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/fc6d194e-6bf5-49ca-bc77-3fdfda62c434@sabinyo.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Luo Jie says:
====================
Add shared PHY counter support for QCA807x and QCA808x
The implementation of the PHY counter is identical for both QCA808x and
QCA807x series devices. This includes counters for both good and bad CRC
frames in the RX and TX directions, which are active when CRC checking
is enabled.
This patch series introduces PHY counter functions into a shared library,
enabling counter support for the QCA808x and QCA807x families through this
common infrastructure. Additionally, enable CRC checking and configure
automatic clearing of counters after reading within config_init() to ensure
accurate counter recording.
v2: https://lore.kernel.org/20250714-qcom_phy_counter-v2-0-94dde9d9769f@quicinc.com
v1: https://lore.kernel.org/20250709-qcom_phy_counter-v1-0-93a54a029c46@quicinc.com
====================
Link: https://patch.msgid.link/20250715-qcom_phy_counter-v3-0-8b0e460a527b@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Within the QCA807X PHY operation's config_init() function, enable CRC
checking for received and transmitted frames and configure counter to
clear after being read to support counter recording. Additionally, add
support for PHY counter operations.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://patch.msgid.link/20250715-qcom_phy_counter-v3-3-8b0e460a527b@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable CRC checking for received and transmitted frames, and configure
counters to clear after being read within config_init() for accurate
counter recording. Additionally, add PHY counter operations and integrate
shared functions.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://patch.msgid.link/20250715-qcom_phy_counter-v3-2-8b0e460a527b@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add PHY counter functionality to the shared library. The implementation
is identical for the current QCA807X and QCA808X PHYs.
The PHY counter can be configured to perform CRC checking for both received
and transmitted packets. Additionally, the packet counter can be set to
automatically clear after it is read.
The PHY counter includes 32-bit packet counters for both RX (received) and
TX (transmitted) packets, as well as 16-bit counters for recording CRC
error packets for both RX and TX.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250715-qcom_phy_counter-v3-1-8b0e460a527b@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bool notify is referenced nowhere else in the function except to check
whether or not to call rtnl_offload_xstats_notify(). Remove it and move
the call to the previous branch.
Signed-off-by: Dennis Chen <dechen@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20250716165750.561175-1-dechen@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Martin KaFai Lau says:
====================
pull-request: bpf-next 2025-07-17
We've added 13 non-merge commits during the last 20 day(s) which contain
a total of 4 files changed, 712 insertions(+), 84 deletions(-).
The main changes are:
1) Avoid skipping or repeating a sk when using a TCP bpf_iter,
from Jordan Rife.
2) Clarify the driver requirement on using the XDP metadata,
from Song Yoong Siang
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next:
doc: xdp: Clarify driver implementation for XDP Rx metadata
selftests/bpf: Add tests for bucket resume logic in established sockets
selftests/bpf: Create iter_tcp_destroy test program
selftests/bpf: Create established sockets in socket iterator tests
selftests/bpf: Make ehash buckets configurable in socket iterator tests
selftests/bpf: Allow for iteration over multiple states
selftests/bpf: Allow for iteration over multiple ports
selftests/bpf: Add tests for bucket resume logic in listening sockets
bpf: tcp: Avoid socket skips and repeats during iteration
bpf: tcp: Use bpf_tcp_iter_batch_item for bpf_tcp_iter_state batch items
bpf: tcp: Get rid of st_bucket_done
bpf: tcp: Make sure iter->batch always contains a full bucket snapshot
bpf: tcp: Make mem flags configurable through bpf_iter_tcp_realloc_batch
====================
Link: https://patch.msgid.link/20250717191731.4142326-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/i915/kernel into drm-fixes
- DP AUX DPCD address fix (Imre)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/aHkQmRhelb4Fzqau@intel.com
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
drm-misc-fixes for v6.16 final?:
- nouveau ioctl validation fix.
- panfrost scheduler bug.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://lore.kernel.org/r/ee784a3a-30b4-489a-8503-b1be3b09268c@linux.intel.com
|
|
The two str_has_prefix() and strstarts() are about the same
with a slight difference on what they return. Group them in
the header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250711085514.1294428-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Change the order of function qualifiers from 'noinline static' to 'static noinline'
in copy_clone_args_from_user for consistency with kernel coding style.
No functional change intended. The goal is to improve readability and
maintain consistent ordering of qualifiers across the codebase.
Signed-off-by: Dishank Jogi <dishank.jogi@siqol.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Link: https://lore.kernel.org/r/20250716093525.449994-1-dishank.jogi@siqol.com
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
We have assembly code generated by a script. GCC successfully compiles
it. However, the kernel cannot load it on an ARM64 platform with a 4K
page size. In contrast, the same ELF file loads correctly on the same
platform with a 64K page size.
The root cause is the Linux kernel's ELF_MIN_ALIGN limitation on the
program headers of ELF files. The ELF file contains 78 program headers
(the script inserts many holes when generating the assembly code). On
ARM64 with a 4K page size, the ELF_MIN_ALLIGN enforces a maximum of 74
program headers, causing the ELF file to fail. However, with a 64K page
size, the ELF_MIN_ALIGN is relaxed to over 1,184 program headers, allowing
the file to run correctly.
Cook kindly identified[1] that this limitation was introduced in
Linux-0.99.15f without an explanation for its purpose.
The ELF specification does not impose such a restriction on program
headers. Removing the ELF_MIN_ALIGN limitation on program headers to
align with the ELF spec. After removing ELF_MIN_ALIGN limitation,
64K size limitation still exist which should be sufficient.
Suggested-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/linux-mm/202506270854.A729825@keescook/ [1]
Signed-off-by: Yin Fengwei <fengwei_yin@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250717110108.55586-1-fengwei_yin@linux.alibaba.com
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Make sure Python doesn't buffer the output, otherwise for some
tests we may see false positive timeouts in NIPA. NIPA thinks that
a machine has hung if the test doesn't print anything for 3min.
This is also nice to heave for running the tests manually,
especially in vng.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20250716205712.1787325-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Kuniyuki Iwashima says:
====================
neighbour: Convert RTM_GETNEIGH to RCU and make pneigh RTNL-free.
This is kind of v3 of the series below [0] but without NEIGHTBL patches.
Patch 1 ~ 4 and 9 come from the series to convert RTM_GETNEIGH to RCU.
Other patches clean up pneigh_lookup() and convert the pneigh code to
RCU + private mutex so that we can easily remove RTNL from RTM_NEWNEIGH
in the later series.
[0]: https://lore.kernel.org/netdev/20250418012727.57033-1-kuniyu@amazon.com/
v2: https://lore.kernel.org/20250712203515.4099110-1-kuniyu@google.com
v1: https://lore.kernel.org/20250711191007.3591938-1-kuniyu@google.com
====================
Link: https://patch.msgid.link/20250716221221.442239-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
neigh_add() updates pneigh_entry() found or created by pneigh_create().
This update is serialised by RTNL, but we will remove it.
Let's move the update part to pneigh_create() and make it return errno
instead of a pointer of pneigh_entry.
Now, the pneigh code is RTNL free.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-16-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tbl->phash_buckets[] is only modified in the slow path by pneigh_create()
and pneigh_delete() under the table lock.
Both of them are called under RTNL, so no extra lock is needed, but we
will remove RTNL from the paths.
pneigh_create() looks up a pneigh_entry, and this part can be lockless,
but it would complicate the logic like
1. lookup
2. allocate pengih_entry for GFP_KERNEL
3. lookup again but under lock
4. if found, return it after freeing the allocated memory
5. else, return the new one
Instead, let's add a per-table mutex and run lookup and allocation
under it.
Note that updating pneigh_entry part in neigh_add() is still protected
by RTNL and will be moved to pneigh_create() in the next patch.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-15-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now, all callers of pneigh_lookup() are under RCU, and the read
lock there is no longer needed.
Let's drop the lock, inline __pneigh_lookup_1() to pneigh_lookup(),
and call it from pneigh_create().
The next patch will remove tbl->lock from pneigh_create().
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-14-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
__pneigh_lookup() is the lockless version of pneigh_lookup(),
but its only caller pndisc_is_router() holds the table lock and
reads pneigh_netry.flags.
This is because accessing pneigh_entry after pneigh_lookup() was
illegal unless the caller holds RTNL or the table lock.
Now, pneigh_entry is guaranteed to be alive during the RCU critical
section.
Let's call pneigh_lookup() and use READ_ONCE() for n->flags in
pndisc_is_router() and remove __pneigh_lookup().
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-13-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now pneigh_entry is guaranteed to be alive during the
RCU critical section even without holding tbl->lock.
Let's use rcu_dereference() in pneigh_get_{first,next}().
Note that neigh_seq_start() still holds tbl->lock for the
normal neighbour entry.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-12-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now pneigh_entry is guaranteed to be alive during the
RCU critical section even without holding tbl->lock.
Let's drop read_lock_bh(&tbl->lock) and use rcu_dereference()
to iterate tbl->phash_buckets[] in pneigh_dump_table()
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-11-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Only __dev_get_by_index() is the RTNL dependant in neigh_get().
Let's replace it with dev_get_by_index_rcu() and convert RTM_GETNEIGH
to RCU.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-10-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
