| Age | Commit message (Collapse) | Author |
|---|
|
Add a 200ms delay after sending a ctrl report to Quadro,
Octo, D5 Next and Aquaero to give them enough time to
process the request and save the data to memory. Otherwise,
under heavier userspace loads where multiple sysfs entries
are usually set in quick succession, a new ctrl report could
be requested from the device while it's still processing the
previous one and fail with -EPIPE. The delay is only applied
if two ctrl report operations are near each other in time.
Reported by a user on Github [1] and tested by both of us.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/82
Fixes: 752b927951ea ("hwmon: (aquacomputer_d5next) Add support for Aquacomputer Octo")
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20230807172004.456968-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Revert a patch that unconditionally resolved addresses to inlines in
callchains, something that was done before when DWARF mode was asked
for, but could as well be done when just frame pointers (the default)
was selected.
This enriches the callchains with inlines but the way to resolve it
is gross right now, relying on addr2line, and even if we come up with
an efficient way of processing all the associated DWARF info for a
big file as vmlinux is, this has to be something people opt-in, as it
will still result in overheads, so revert it until we get this done
in a saner way.
- Update the x86 msr-index.h header with the kernel original, no change
in tooling output, just addresses a tools/perf build warning.
- Resolve a regression where special "tool events", such as
"duration_time" were being presented for all CPUs, when it only
makes sense to show it for the workload, that is, just once.
* tag 'perf-tools-fixes-for-v6.5-3-2023-08-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf stat: Don't display zero tool counts
tools arch x86: Sync the msr-index.h copy with the kernel sources
Revert "perf report: Append inlines to non-DWARF callchains"
|
|
Commit 16d7fd3cfa72 ("zonefs: use iomap for synchronous direct writes")
changes zonefs code from a self-built zone append BIO to using iomap for
synchronous direct writes. This change relies on iomap submit BIO
callback to change the write BIO built by iomap to a zone append BIO.
However, this change overlooked the fact that a write BIO may be very
large as it is split when issued. The change from a regular write to a
zone append operation for the built BIO can result in a block layer
warning as zone append BIO are not allowed to be split.
WARNING: CPU: 18 PID: 202210 at block/bio.c:1644 bio_split+0x288/0x350
Call Trace:
? __warn+0xc9/0x2b0
? bio_split+0x288/0x350
? report_bug+0x2e6/0x390
? handle_bug+0x41/0x80
? exc_invalid_op+0x13/0x40
? asm_exc_invalid_op+0x16/0x20
? bio_split+0x288/0x350
bio_split_rw+0x4bc/0x810
? __pfx_bio_split_rw+0x10/0x10
? lockdep_unlock+0xf2/0x250
__bio_split_to_limits+0x1d8/0x900
blk_mq_submit_bio+0x1cf/0x18a0
? __pfx_iov_iter_extract_pages+0x10/0x10
? __pfx_blk_mq_submit_bio+0x10/0x10
? find_held_lock+0x2d/0x110
? lock_release+0x362/0x620
? mark_held_locks+0x9e/0xe0
__submit_bio+0x1ea/0x290
? __pfx___submit_bio+0x10/0x10
? seqcount_lockdep_reader_access.constprop.0+0x82/0x90
submit_bio_noacct_nocheck+0x675/0xa20
? __pfx_bio_iov_iter_get_pages+0x10/0x10
? __pfx_submit_bio_noacct_nocheck+0x10/0x10
iomap_dio_bio_iter+0x624/0x1280
__iomap_dio_rw+0xa22/0x18a0
? lock_is_held_type+0xe3/0x140
? __pfx___iomap_dio_rw+0x10/0x10
? lock_release+0x362/0x620
? zonefs_file_write_iter+0x74c/0xc80 [zonefs]
? down_write+0x13d/0x1e0
iomap_dio_rw+0xe/0x40
zonefs_file_write_iter+0x5ea/0xc80 [zonefs]
do_iter_readv_writev+0x18b/0x2c0
? __pfx_do_iter_readv_writev+0x10/0x10
? inode_security+0x54/0xf0
do_iter_write+0x13b/0x7c0
? lock_is_held_type+0xe3/0x140
vfs_writev+0x185/0x550
? __pfx_vfs_writev+0x10/0x10
? __handle_mm_fault+0x9bd/0x1c90
? find_held_lock+0x2d/0x110
? lock_release+0x362/0x620
? find_held_lock+0x2d/0x110
? lock_release+0x362/0x620
? __up_read+0x1ea/0x720
? do_pwritev+0x136/0x1f0
do_pwritev+0x136/0x1f0
? __pfx_do_pwritev+0x10/0x10
? syscall_enter_from_user_mode+0x22/0x90
? lockdep_hardirqs_on+0x7d/0x100
do_syscall_64+0x58/0x80
This error depends on the hardware used, specifically on the max zone
append bytes and max_[hw_]sectors limits. Tests using AMD Epyc machines
that have low limits did not reveal this issue while runs on Intel Xeon
machines with larger limits trigger it.
Manually splitting the zone append BIO using bio_split_rw() can solve
this issue but also requires issuing the fragment BIOs synchronously
with submit_bio_wait(), to avoid potential reordering of the zone append
BIO fragments, which would lead to data corruption. That is, this
solution is not better than using regular write BIOs which are subject
to serialization using zone write locking at the IO scheduler level.
Given this, fix the issue by removing zone append support and using
regular write BIOs for synchronous direct writes. This allows preseving
the use of iomap and having identical synchronous and asynchronous
sequential file write path. Zone append support will be reintroduced
later through io_uring commands to ensure that the needed special
handling is done correctly.
Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 16d7fd3cfa72 ("zonefs: use iomap for synchronous direct writes")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Xu Kuohai says:
====================
bug fixes and a new test case for sockmap.
v3:
fix bpf ci failure
v2: https://lore.kernel.org/bpf/20230803064838.108784-1-xukuohai@huaweicloud.com
add a test case
v1:
https://lore.kernel.org/bpf/20230728105649.3978774-1-xukuohai@huaweicloud.com
https://lore.kernel.org/bpf/20230728105717.3978849-1-xukuohai@huaweicloud.com
====================
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
Add a test case to check whether sockmap redirection works correctly
when data length returned by stream_parser is less than skb->len.
In addition, this test checks whether strp_done is called correctly.
The reason is that we returns skb->len - 1 from the stream_parser, so
the last byte in the skb will be held by strp->skb_head. Therefore,
if strp_done is not called to free strp->skb_head, we'll get a memleak
warning.
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20230804073740.194770-5-xukuohai@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
BPF CI has reported the following failure:
Error: #200/79 sockmap_listen/sockmap VSOCK test_vsock_redir
Error: #200/79 sockmap_listen/sockmap VSOCK test_vsock_redir
./test_progs:vsock_unix_redir_connectible:1506: egress: write: Transport endpoint is not connected
vsock_unix_redir_connectible:FAIL:1506
./test_progs:vsock_unix_redir_connectible:1506: ingress: write: Transport endpoint is not connected
vsock_unix_redir_connectible:FAIL:1506
./test_progs:vsock_unix_redir_connectible:1506: egress: write: Transport endpoint is not connected
vsock_unix_redir_connectible:FAIL:1506
./test_progs:vsock_unix_redir_connectible:1514: ingress: recv() err, errno=11
vsock_unix_redir_connectible:FAIL:1514
./test_progs:vsock_unix_redir_connectible:1518: ingress: vsock socket map failed, a != b
vsock_unix_redir_connectible:FAIL:1518
./test_progs:vsock_unix_redir_connectible:1525: ingress: want pass count 1, have 0
It’s because the recv(... MSG_DONTWAIT) syscall in the test case is
called before the queued work sk_psock_backlog() in the kernel finishes
executing. So the data to be read is still queued in psock->ingress_skb
and cannot be read by the user program. Therefore, the non-blocking
recv() reads nothing and reports an EAGAIN error.
So replace recv(... MSG_DONTWAIT) with xrecv_nonblock(), which calls
select() to wait for data to be readable or timeout before calls recv().
Fixes: d61bd8c1fd02 ("selftests/bpf: add a test case for vsock sockmap")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20230804073740.194770-4-xukuohai@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
strp_done is only called when psock->progs.stream_parser is not NULL,
but stream_parser was set to NULL by sk_psock_stop_strp(), called
by sk_psock_drop() earlier. So, strp_done can never be called.
Introduce SK_PSOCK_RX_ENABLED to mark whether there is strp on psock.
Change the condition for calling strp_done from judging whether
stream_parser is set to judging whether this flag is set. This flag is
only set once when strp_init() succeeds, and will never be cleared later.
Fixes: c0d95d3380ee ("bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20230804073740.194770-3-xukuohai@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
sock_map_del_link() operates on both SOCKMAP and SOCKHASH, although
both types have member named "progs", the offset of "progs" member in
these two types is different, so "progs" should be accessed with the
real map type.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20230804073740.194770-2-xukuohai@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
Fix a refcount underflow problem reported by syzbot that can happen
when a system is running out of memory. If xp_alloc_tx_descs() fails,
and it can only fail due to not having enough memory, then the error
path is triggered. In this error path, the refcount of the pool is
decremented as it has incremented before. However, the reference to
the pool in the socket was not nulled. This means that when the socket
is closed later, the socket teardown logic will think that there is a
pool attached to the socket and try to decrease the refcount again,
leading to a refcount underflow.
I chose this fix as it involved adding just a single line. Another
option would have been to move xp_get_pool() and the assignment of
xs->pool to after the if-statement and using xs_umem->pool instead of
xs->pool in the whole if-statement resulting in somewhat simpler code,
but this would have led to much more churn in the code base perhaps
making it harder to backport.
Fixes: ba3beec2ec1d ("xsk: Fix possible crash when multiple sockets are created")
Reported-by: syzbot+8ada0057e69293a05fd4@syzkaller.appspotmail.com
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/r/20230809142843.13944-1-magnus.karlsson@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
The upcoming (and nearly finalized):
https://datatracker.ietf.org/doc/draft-collink-6man-pio-pflag/
will update the IPv6 RA to include a new flag in the PIO field,
which will serve as a hint to perform DHCPv6-PD.
As we don't want DHCPv6 related logic inside the kernel, this piece of
information needs to be exposed to userspace. The simplest option is to
simply expose the entire PIO through the already existing mechanism.
Even without this new flag, the already existing PIO R (router address)
flag (from RFC6275) cannot AFAICT be handled entirely in kernel,
and provides useful information that should be exposed to userspace
(the router's global address, for use by Mobile IPv6).
Also cc'ing stable@ for inclusion in LTS, as while technically this is
not quite a bugfix, and instead more of a feature, it is absolutely
trivial and the alternative is manually cherrypicking into all Android
Common Kernel trees - and I know Greg will ask for it to be sent in via
LTS instead...
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: YOSHIFUJI Hideaki / 吉藤英明 <yoshfuji@linux-ipv6.org>
Cc: stable@vger.kernel.org
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20230807102533.1147559-1-maze@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Just a few small updates:
* fix an integer overflow in nl80211
* fix rtw89 8852AE disconnections
* fix a buffer overflow in ath12k
* fix AP_VLAN configuration lookups
* fix allocation failure handling in brcm80211
* update MAINTAINERS for some drivers
* tag 'wireless-2023-08-09' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: ath12k: Fix buffer overflow when scanning with extraie
wifi: nl80211: fix integer overflow in nl80211_parse_mbssid_elems()
wifi: cfg80211: fix sband iftype data lookup for AP_VLAN
wifi: rtw89: fix 8852AE disconnection caused by RX full flags
MAINTAINERS: Remove tree entry for rtl8180
MAINTAINERS: Update entry for rtl8187
wifi: brcm80211: handle params_v1 allocation failure
====================
Link: https://lore.kernel.org/r/20230809124818.167432-2-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The q->stats->accounting is not only used by iocost, but iocost only
increase this counter, never decrease it. So queue stats accounting
will always enabled after using iocost once.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230804070609.31623-1-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Normally these two flags do go together, as the issuer of polled IO
generally cannot wait for resources that will get freed as part of IO
completion. This is because that very task is the one that will complete
the request and free those resources, hence that would introduce a
deadlock.
But it is possible to have someone else issue the polled IO, eg via
io_uring if the request is punted to io-wq. For that case, it's fine to
have the task block on IO submission, as it is not the same task that
will be completing the IO.
It's completely up to the caller to ask for both polled and nowait IO
separately! If we don't allow polled IO where IOCB_NOWAIT isn't set in
the kiocb, then we can run into repeated -EAGAIN submissions and not
make any progress.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Ido Schimmel says:
====================
selftests: forwarding: Various fixes
Fix various problems with forwarding selftests. See individual patches
for problem description and solution.
====================
Link: https://lore.kernel.org/r/20230808141503.4060661-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some test cases check that the group timer is (or isn't) 0. Instead of
grepping for "0.00" grep for " 0.00" as the former can also match
"260.00" which is the default group membership interval.
Fixes: b6d00da08610 ("selftests: forwarding: Add bridge MDB test")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-18-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 8bcfb4ae4d97 ("selftests: forwarding: Fix failing
tests with old libnet"), old versions of libnet (used by mausezahn) do
not use the "SO_BINDTODEVICE" socket option. For IP unicast packets,
this can be solved by prefixing mausezahn invocations with "ip vrf
exec". However, IP multicast packets do not perform routing and simply
egress the bound device, which does not exist in this case.
Fix by specifying the source and destination MAC of the packet which
will cause mausezahn to use a packet socket instead of an IP socket.
Fixes: 3446dcd7df05 ("selftests: forwarding: bridge_mdb_max: Add a new selftest")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-17-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 8bcfb4ae4d97 ("selftests: forwarding: Fix failing
tests with old libnet"), old versions of libnet (used by mausezahn) do
not use the "SO_BINDTODEVICE" socket option. For IP unicast packets,
this can be solved by prefixing mausezahn invocations with "ip vrf
exec". However, IP multicast packets do not perform routing and simply
egress the bound device, which does not exist in this case.
Fix by specifying the source and destination MAC of the packet which
will cause mausezahn to use a packet socket instead of an IP socket.
Fixes: b6d00da08610 ("selftests: forwarding: Add bridge MDB test")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-16-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 8bcfb4ae4d97 ("selftests: forwarding: Fix failing
tests with old libnet"), old versions of libnet (used by mausezahn) do
not use the "SO_BINDTODEVICE" socket option. For IP unicast packets,
this can be solved by prefixing mausezahn invocations with "ip vrf
exec". However, IP multicast packets do not perform routing and simply
egress the bound device, which does not exist in this case.
Fix by specifying the source and destination MAC of the packet which
will cause mausezahn to use a packet socket instead of an IP socket.
Fixes: 8c33266ae26a ("selftests: forwarding: Add layer 2 miss test cases")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-15-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The test installs filters that match on various IP fragments (e.g., no
fragment, first fragment) and expects a certain amount of packets to hit
each filter. This is problematic as the filters are not specific enough
and can match IP packets (e.g., IGMP) generated by the stack, resulting
in failures [1].
Fix by making the filters more specific and match on more fields in the
IP header: Source IP, destination IP and protocol.
[1]
# timeout set to 0
# selftests: net/forwarding: tc_tunnel_key.sh
# TEST: tunnel_key nofrag (skip_hw) [FAIL]
# packet smaller than MTU was not tunneled
# INFO: Could not test offloaded functionality
not ok 89 selftests: net/forwarding: tc_tunnel_key.sh # exit=1
Fixes: 533a89b1940f ("selftests: forwarding: add tunnel_key "nofrag" test case")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-14-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The test checks that filters that match on source or destination MAC
were only hit once. A host can send more than one packet with a given
source or destination MAC, resulting in failures.
Fix by relaxing the success criterion and instead check that the filters
were not hit zero times. Using tc_check_at_least_x_packets() is also an
option, but it is not available in older kernels.
Fixes: 07e5c75184a1 ("selftests: forwarding: Introduce tc flower matching tests")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-13-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The test relies on 'nc' being the netcat version from the nmap project.
While this seems to be the case on Fedora, it is not the case on Ubuntu,
resulting in failures such as [1].
Fix by explicitly using the 'ncat' utility from the nmap project and the
skip the test in case it is not installed.
[1]
# timeout set to 0
# selftests: net/forwarding: tc_actions.sh
# TEST: gact drop and ok (skip_hw) [ OK ]
# TEST: mirred egress flower redirect (skip_hw) [ OK ]
# TEST: mirred egress flower mirror (skip_hw) [ OK ]
# TEST: mirred egress matchall mirror (skip_hw) [ OK ]
# TEST: mirred_egress_to_ingress (skip_hw) [ OK ]
# nc: invalid option -- '-'
# usage: nc [-46CDdFhklNnrStUuvZz] [-I length] [-i interval] [-M ttl]
# [-m minttl] [-O length] [-P proxy_username] [-p source_port]
# [-q seconds] [-s sourceaddr] [-T keyword] [-V rtable] [-W recvlimit]
# [-w timeout] [-X proxy_protocol] [-x proxy_address[:port]]
# [destination] [port]
# nc: invalid option -- '-'
# usage: nc [-46CDdFhklNnrStUuvZz] [-I length] [-i interval] [-M ttl]
# [-m minttl] [-O length] [-P proxy_username] [-p source_port]
# [-q seconds] [-s sourceaddr] [-T keyword] [-V rtable] [-W recvlimit]
# [-w timeout] [-X proxy_protocol] [-x proxy_address[:port]]
# [destination] [port]
# TEST: mirred_egress_to_ingress_tcp (skip_hw) [FAIL]
# server output check failed
# INFO: Could not test offloaded functionality
not ok 80 selftests: net/forwarding: tc_actions.sh # exit=1
Fixes: ca22da2fbd69 ("act_mirred: use the backlog for nested calls to mirred ingress")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-12-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MAC Merge cannot be tested with veth pairs, resulting in failures:
# ./ethtool_mm.sh
[...]
TEST: Manual configuration with verification: swp1 to swp2 [FAIL]
Verification did not succeed
Fix by skipping the test when the interfaces do not support MAC Merge.
Fixes: e6991384ace5 ("selftests: forwarding: add a test for MAC Merge layer")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-11-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Layer 3 hardware stats cannot be used when the underlying interfaces are
veth pairs, resulting in failures:
# ./hw_stats_l3_gre.sh
TEST: ping gre flat [ OK ]
TEST: Test rx packets: [FAIL]
Traffic not reflected in the counter: 0 -> 0
TEST: Test tx packets: [FAIL]
Traffic not reflected in the counter: 0 -> 0
Fix by skipping the test when used with veth pairs.
Fixes: 813f97a26860 ("selftests: forwarding: Add a tunnel-based test for L3 HW stats")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-10-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ethtool extended state cannot be tested with veth pairs, resulting in
failures:
# ./ethtool_extended_state.sh
TEST: Autoneg, No partner detected [FAIL]
Expected "Autoneg", got "Link detected: no"
[...]
Fix by skipping the test when used with veth pairs.
Fixes: 7d10bcce98cd ("selftests: forwarding: Add tests for ethtool extended state")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-9-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Auto-negotiation cannot be tested with veth pairs, resulting in
failures:
# ./ethtool.sh
TEST: force of same speed autoneg off [FAIL]
error in configuration. swp1 speed Not autoneg off
[...]
Fix by skipping the test when used with veth pairs.
Fixes: 64916b57c0b1 ("selftests: forwarding: Add speed and auto-negotiation test")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-8-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A handful of tests require physical loopbacks to be used instead of veth
pairs. Add a helper that these tests will invoke in order to be skipped
when executed with veth pairs.
Fixes: 64916b57c0b1 ("selftests: forwarding: Add speed and auto-negotiation test")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-7-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The test uses the 'TROUTE6' environment variable to encode the name of
the IPv6 traceroute utility. By default (without a configuration file),
this variable is not set, resulting in failures:
# ./ip6_forward_instats_vrf.sh
TEST: ping6 [ OK ]
TEST: Ip6InTooBigErrors [ OK ]
TEST: Ip6InHdrErrors [FAIL]
TEST: Ip6InAddrErrors [ OK ]
TEST: Ip6InDiscards [ OK ]
Fix by setting a default utility name and skip the test if the utility
is not present.
Fixes: 0857d6f8c759 ("ipv6: When forwarding count rx stats on the orig netdev")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-6-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The selftest relies on iproute2 changes present in version 6.3, but the
test does not check for it, resulting in errors:
# ./bridge_mdb_max.sh
INFO: 802.1d tests
TEST: cfg4: port: ngroups reporting [FAIL]
Number of groups was null, now is null, but 5 expected
TEST: ctl4: port: ngroups reporting [FAIL]
Number of groups was null, now is null, but 5 expected
TEST: cfg6: port: ngroups reporting [FAIL]
Number of groups was null, now is null, but 5 expected
[...]
Fix by skipping the test if iproute2 is too old.
Fixes: 3446dcd7df05 ("selftests: forwarding: bridge_mdb_max: Add a new selftest")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/6b04b2ba-2372-6f6b-3ac8-b7cba1cfae83@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-5-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The selftest relies on iproute2 changes present in version 6.3, but the
test does not check for it, resulting in error:
# ./bridge_mdb.sh
INFO: # Host entries configuration tests
TEST: Common host entries configuration tests (IPv4) [FAIL]
Managed to add IPv4 host entry with a filter mode
TEST: Common host entries configuration tests (IPv6) [FAIL]
Managed to add IPv6 host entry with a filter mode
TEST: Common host entries configuration tests (L2) [FAIL]
Managed to add L2 host entry with a filter mode
INFO: # Port group entries configuration tests - (*, G)
Command "replace" is unknown, try "bridge mdb help".
[...]
Fix by skipping the test if iproute2 is too old.
Fixes: b6d00da08610 ("selftests: forwarding: Add bridge MDB test")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/6b04b2ba-2372-6f6b-3ac8-b7cba1cfae83@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-4-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The default timeout for selftests is 45 seconds, but it is not enough
for forwarding selftests which can takes minutes to finish depending on
the number of tests cases:
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# TEST: IGMPv2 report 239.10.10.10 [ OK ]
# TEST: IGMPv2 leave 239.10.10.10 [ OK ]
# TEST: IGMPv3 report 239.10.10.10 is_include [ OK ]
# TEST: IGMPv3 report 239.10.10.10 include -> allow [ OK ]
#
not ok 1 selftests: net/forwarding: bridge_igmp.sh # TIMEOUT 45 seconds
Fix by switching off the timeout and setting it to 0. A similar change
was done for BPF selftests in commit 6fc5916cc256 ("selftests: bpf:
Switch off timeout").
Fixes: 81573b18f26d ("selftests/net/forwarding: add Makefile to install tests")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/8d149f8c-818e-d141-a0ce-a6bae606bc22@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-3-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in [1], the forwarding selftests are meant to be run with
either physical loopbacks or veth pairs. The interfaces are expected to
be specified in a user-provided forwarding.config file or as command
line arguments. By default, this file is not present and the tests fail:
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
[...]
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# Command line is not complete. Try option "help"
# Failed to create netif
not ok 1 selftests: net/forwarding: bridge_igmp.sh # exit=1
[...]
Fix by skipping a test if interfaces are not provided either via the
configuration file or command line arguments.
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
[...]
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# SKIP: Cannot create interface. Name not specified
ok 1 selftests: net/forwarding: bridge_igmp.sh # SKIP
[1] tools/testing/selftests/net/forwarding/README
Fixes: 81573b18f26d ("selftests/net/forwarding: add Makefile to install tests")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/856d454e-f83c-20cf-e166-6dc06cbc1543@alu.unizg.hr/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230808141503.4060661-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before this code is copied, add the missing family, as we did in
commit 3dd344ea84e1 ("net: tracepoint: exposing sk_family in all tcp:tracepoints")
Fixes: 15fcdf6ae116 ("tcp: Add tracepoint for tcp_set_ca_state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ping Gan <jacky_gam_2001@163.com>
Cc: Manjusaka <me@manjusaka.me>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230808084923.2239142-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ido Schimmel says:
====================
nexthop: Nexthop dump fixes
Patches #1 and #3 fix two problems related to nexthops and nexthop
buckets dump, respectively. Patch #2 is a preparation for the third
patch.
The pattern described in these patches of splitting the NLMSG_DONE to a
separate response is prevalent in other rtnetlink dump callbacks. I
don't know if it's because I'm missing something or if this was done
intentionally to ensure the message is delivered to user space. After
commit 0642840b8bb0 ("af_netlink: ensure that NLMSG_DONE never fails in
dumps") this is no longer necessary and I can improve these dump
callbacks assuming this analysis is correct.
No regressions in existing tests:
# ./fib_nexthops.sh
[...]
Tests passed: 230
Tests failed: 0
====================
Link: https://lore.kernel.org/r/20230808075233.3337922-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A netlink dump callback can return a positive number to signal that more
information needs to be dumped or zero to signal that the dump is
complete. In the second case, the core netlink code will append the
NLMSG_DONE message to the skb in order to indicate to user space that
the dump is complete.
The nexthop bucket dump callback always returns a positive number if
nexthop buckets were filled in the provided skb, even if the dump is
complete. This means that a dump will span at least two recvmsg() calls
as long as nexthop buckets are present. In the last recvmsg() call the
dump callback will not fill in any nexthop buckets because the previous
call indicated that the dump should restart from the last dumped nexthop
ID plus one.
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id 10 group 1 type resilient buckets 2
# strace -e sendto,recvmsg -s 5 ip nexthop bucket
sendto(3, [[{nlmsg_len=24, nlmsg_type=RTM_GETNEXTHOPBUCKET, nlmsg_flags=NLM_F_REQUEST|NLM_F_DUMP, nlmsg_seq=1691396980, nlmsg_pid=0}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], {nlmsg_len=0, nlmsg_type=0 /* NLMSG_??? */, nlmsg_flags=0, nlmsg_seq=0, nlmsg_pid=0}], 152, 0, NULL, 0) = 152
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 128
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[[{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396980, nlmsg_pid=347}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], [{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396980, nlmsg_pid=347}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}]], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 128
id 10 index 0 idle_time 6.66 nhid 1
id 10 index 1 idle_time 6.66 nhid 1
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 20
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[{nlmsg_len=20, nlmsg_type=NLMSG_DONE, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396980, nlmsg_pid=347}, 0], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 20
+++ exited with 0 +++
This behavior is both inefficient and buggy. If the last nexthop to be
dumped had the maximum ID of 0xffffffff, then the dump will restart from
0 (0xffffffff + 1) and never end:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id $((2**32-1)) group 1 type resilient buckets 2
# ip nexthop bucket
id 4294967295 index 0 idle_time 5.55 nhid 1
id 4294967295 index 1 idle_time 5.55 nhid 1
id 4294967295 index 0 idle_time 5.55 nhid 1
id 4294967295 index 1 idle_time 5.55 nhid 1
[...]
Fix by adjusting the dump callback to return zero when the dump is
complete. After the fix only one recvmsg() call is made and the
NLMSG_DONE message is appended to the RTM_NEWNEXTHOPBUCKET responses:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id $((2**32-1)) group 1 type resilient buckets 2
# strace -e sendto,recvmsg -s 5 ip nexthop bucket
sendto(3, [[{nlmsg_len=24, nlmsg_type=RTM_GETNEXTHOPBUCKET, nlmsg_flags=NLM_F_REQUEST|NLM_F_DUMP, nlmsg_seq=1691396737, nlmsg_pid=0}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], {nlmsg_len=0, nlmsg_type=0 /* NLMSG_??? */, nlmsg_flags=0, nlmsg_seq=0, nlmsg_pid=0}], 152, 0, NULL, 0) = 152
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 148
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[[{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396737, nlmsg_pid=350}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], [{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396737, nlmsg_pid=350}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], [{nlmsg_len=20, nlmsg_type=NLMSG_DONE, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396737, nlmsg_pid=350}, 0]], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 148
id 4294967295 index 0 idle_time 6.61 nhid 1
id 4294967295 index 1 idle_time 6.61 nhid 1
+++ exited with 0 +++
Note that if the NLMSG_DONE message cannot be appended because of size
limitations, then another recvmsg() will be needed, but the core netlink
code will not invoke the dump callback and simply reply with a
NLMSG_DONE message since it knows that the callback previously returned
zero.
Add a test that fails before the fix:
# ./fib_nexthops.sh -t basic_res
[...]
TEST: Maximum nexthop ID dump [FAIL]
[...]
And passes after it:
# ./fib_nexthops.sh -t basic_res
[...]
TEST: Maximum nexthop ID dump [ OK ]
[...]
Fixes: 8a1bbabb034d ("nexthop: Add netlink handlers for bucket dump")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230808075233.3337922-4-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rtm_dump_nexthop_bucket_nh() is used to dump nexthop buckets belonging
to a specific resilient nexthop group. The function returns a positive
return code (the skb length) upon both success and failure.
The above behavior is problematic. When a complete nexthop bucket dump
is requested, the function that walks the different nexthops treats the
non-zero return code as an error. This causes buckets belonging to
different resilient nexthop groups to be dumped using different buffers
even if they can all fit in the same buffer:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id 10 group 1 type resilient buckets 1
# ip nexthop add id 20 group 1 type resilient buckets 1
# strace -e recvmsg -s 0 ip nexthop bucket
[...]
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[...], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 64
id 10 index 0 idle_time 10.27 nhid 1
[...]
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[...], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 64
id 20 index 0 idle_time 6.44 nhid 1
[...]
Fix by only returning a non-zero return code when an error occurred and
restarting the dump from the bucket index we failed to fill in. This
allows buckets belonging to different resilient nexthop groups to be
dumped using the same buffer:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id 10 group 1 type resilient buckets 1
# ip nexthop add id 20 group 1 type resilient buckets 1
# strace -e recvmsg -s 0 ip nexthop bucket
[...]
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[...], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 128
id 10 index 0 idle_time 30.21 nhid 1
id 20 index 0 idle_time 26.7 nhid 1
[...]
While this change is more of a performance improvement change than an
actual bug fix, it is a prerequisite for a subsequent patch that does
fix a bug.
Fixes: 8a1bbabb034d ("nexthop: Add netlink handlers for bucket dump")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230808075233.3337922-3-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A netlink dump callback can return a positive number to signal that more
information needs to be dumped or zero to signal that the dump is
complete. In the second case, the core netlink code will append the
NLMSG_DONE message to the skb in order to indicate to user space that
the dump is complete.
The nexthop dump callback always returns a positive number if nexthops
were filled in the provided skb, even if the dump is complete. This
means that a dump will span at least two recvmsg() calls as long as
nexthops are present. In the last recvmsg() call the dump callback will
not fill in any nexthops because the previous call indicated that the
dump should restart from the last dumped nexthop ID plus one.
# ip nexthop add id 1 blackhole
# strace -e sendto,recvmsg -s 5 ip nexthop
sendto(3, [[{nlmsg_len=24, nlmsg_type=RTM_GETNEXTHOP, nlmsg_flags=NLM_F_REQUEST|NLM_F_DUMP, nlmsg_seq=1691394315, nlmsg_pid=0}, {nh_family=AF_UNSPEC, nh_scope=RT_SCOPE_UNIVERSE, nh_protocol=RTPROT_UNSPEC, nh_flags=0}], {nlmsg_len=0, nlmsg_type=0 /* NLMSG_??? */, nlmsg_flags=0, nlmsg_seq=0, nlmsg_pid=0}], 152, 0, NULL, 0) = 152
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 36
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[{nlmsg_len=36, nlmsg_type=RTM_NEWNEXTHOP, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691394315, nlmsg_pid=343}, {nh_family=AF_INET, nh_scope=RT_SCOPE_UNIVERSE, nh_protocol=RTPROT_UNSPEC, nh_flags=0}, [[{nla_len=8, nla_type=NHA_ID}, 1], {nla_len=4, nla_type=NHA_BLACKHOLE}]], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 36
id 1 blackhole
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 20
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[{nlmsg_len=20, nlmsg_type=NLMSG_DONE, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691394315, nlmsg_pid=343}, 0], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 20
+++ exited with 0 +++
This behavior is both inefficient and buggy. If the last nexthop to be
dumped had the maximum ID of 0xffffffff, then the dump will restart from
0 (0xffffffff + 1) and never end:
# ip nexthop add id $((2**32-1)) blackhole
# ip nexthop
id 4294967295 blackhole
id 4294967295 blackhole
[...]
Fix by adjusting the dump callback to return zero when the dump is
complete. After the fix only one recvmsg() call is made and the
NLMSG_DONE message is appended to the RTM_NEWNEXTHOP response:
# ip nexthop add id $((2**32-1)) blackhole
# strace -e sendto,recvmsg -s 5 ip nexthop
sendto(3, [[{nlmsg_len=24, nlmsg_type=RTM_GETNEXTHOP, nlmsg_flags=NLM_F_REQUEST|NLM_F_DUMP, nlmsg_seq=1691394080, nlmsg_pid=0}, {nh_family=AF_UNSPEC, nh_scope=RT_SCOPE_UNIVERSE, nh_protocol=RTPROT_UNSPEC, nh_flags=0}], {nlmsg_len=0, nlmsg_type=0 /* NLMSG_??? */, nlmsg_flags=0, nlmsg_seq=0, nlmsg_pid=0}], 152, 0, NULL, 0) = 152
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 56
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[[{nlmsg_len=36, nlmsg_type=RTM_NEWNEXTHOP, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691394080, nlmsg_pid=342}, {nh_family=AF_INET, nh_scope=RT_SCOPE_UNIVERSE, nh_protocol=RTPROT_UNSPEC, nh_flags=0}, [[{nla_len=8, nla_type=NHA_ID}, 4294967295], {nla_len=4, nla_type=NHA_BLACKHOLE}]], [{nlmsg_len=20, nlmsg_type=NLMSG_DONE, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691394080, nlmsg_pid=342}, 0]], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 56
id 4294967295 blackhole
+++ exited with 0 +++
Note that if the NLMSG_DONE message cannot be appended because of size
limitations, then another recvmsg() will be needed, but the core netlink
code will not invoke the dump callback and simply reply with a
NLMSG_DONE message since it knows that the callback previously returned
zero.
Add a test that fails before the fix:
# ./fib_nexthops.sh -t basic
[...]
TEST: Maximum nexthop ID dump [FAIL]
[...]
And passes after it:
# ./fib_nexthops.sh -t basic
[...]
TEST: Maximum nexthop ID dump [ OK ]
[...]
Fixes: ab84be7e54fc ("net: Initial nexthop code")
Reported-by: Petr Machata <petrm@nvidia.com>
Closes: https://lore.kernel.org/netdev/87sf91enuf.fsf@nvidia.com/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230808075233.3337922-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The referenced commit intended to fix memleak of VLAN 0 that is implicitly
created on devices with NETIF_F_HW_VLAN_CTAG_FILTER feature. However, it
doesn't take into account that the feature can be re-set during the
netdevice lifetime which will cause memory leak if feature is disabled
during the device deletion as illustrated by [0]. Fix the leak by
unconditionally deleting VLAN 0 on NETDEV_DOWN event.
[0]:
> modprobe 8021q
> ip l set dev eth2 up
> ethtool -K eth2 rx-vlan-filter off
> modprobe -r mlx5_ib
> modprobe -r mlx5_core
> cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff888103dcd900 (size 256):
comm "ip", pid 1490, jiffies 4294907305 (age 325.364s)
hex dump (first 32 bytes):
00 80 5d 03 81 88 ff ff 00 00 00 00 00 00 00 00 ..].............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000899f3bb9>] kmalloc_trace+0x25/0x80
[<000000002889a7a2>] vlan_vid_add+0xa0/0x210
[<000000007177800e>] vlan_device_event+0x374/0x760 [8021q]
[<000000009a0716b1>] notifier_call_chain+0x35/0xb0
[<00000000bbf3d162>] __dev_notify_flags+0x58/0xf0
[<0000000053d2b05d>] dev_change_flags+0x4d/0x60
[<00000000982807e9>] do_setlink+0x28d/0x10a0
[<0000000058c1be00>] __rtnl_newlink+0x545/0x980
[<00000000e66c3bd9>] rtnl_newlink+0x44/0x70
[<00000000a2cc5970>] rtnetlink_rcv_msg+0x29c/0x390
[<00000000d307d1e4>] netlink_rcv_skb+0x54/0x100
[<00000000259d16f9>] netlink_unicast+0x1f6/0x2c0
[<000000007ce2afa1>] netlink_sendmsg+0x232/0x4a0
[<00000000f3f4bb39>] sock_sendmsg+0x38/0x60
[<000000002f9c0624>] ____sys_sendmsg+0x1e3/0x200
[<00000000d6ff5520>] ___sys_sendmsg+0x80/0xc0
unreferenced object 0xffff88813354fde0 (size 32):
comm "ip", pid 1490, jiffies 4294907305 (age 325.364s)
hex dump (first 32 bytes):
a0 d9 dc 03 81 88 ff ff a0 d9 dc 03 81 88 ff ff ................
81 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000899f3bb9>] kmalloc_trace+0x25/0x80
[<000000002da64724>] vlan_vid_add+0xdf/0x210
[<000000007177800e>] vlan_device_event+0x374/0x760 [8021q]
[<000000009a0716b1>] notifier_call_chain+0x35/0xb0
[<00000000bbf3d162>] __dev_notify_flags+0x58/0xf0
[<0000000053d2b05d>] dev_change_flags+0x4d/0x60
[<00000000982807e9>] do_setlink+0x28d/0x10a0
[<0000000058c1be00>] __rtnl_newlink+0x545/0x980
[<00000000e66c3bd9>] rtnl_newlink+0x44/0x70
[<00000000a2cc5970>] rtnetlink_rcv_msg+0x29c/0x390
[<00000000d307d1e4>] netlink_rcv_skb+0x54/0x100
[<00000000259d16f9>] netlink_unicast+0x1f6/0x2c0
[<000000007ce2afa1>] netlink_sendmsg+0x232/0x4a0
[<00000000f3f4bb39>] sock_sendmsg+0x38/0x60
[<000000002f9c0624>] ____sys_sendmsg+0x1e3/0x200
[<00000000d6ff5520>] ___sys_sendmsg+0x80/0xc0
Fixes: efc73f4bbc23 ("net: Fix memory leak - vlan_info struct")
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Link: https://lore.kernel.org/r/20230808093521.1468929-1-vladbu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Yingcong has noticed that on the 5-level paging machine, VDSO and VVAR
VMAs are placed above the 47-bit border:
8000001a9000-8000001ad000 r--p 00000000 00:00 0 [vvar]
8000001ad000-8000001af000 r-xp 00000000 00:00 0 [vdso]
This might confuse users who are not aware of 5-level paging and expect
all userspace addresses to be under the 47-bit border.
So far problem has only been triggered with ASLR disabled, although it
may also occur with ASLR enabled if the layout is randomized in a just
right way.
The problem happens due to custom placement for the VMAs in the VDSO
code: vdso_addr() tries to place them above the stack and checks the
result against TASK_SIZE_MAX, which is wrong. TASK_SIZE_MAX is set to
the 56-bit border on 5-level paging machines. Use DEFAULT_MAP_WINDOW
instead.
Fixes: b569bab78d8d ("x86/mm: Prepare to expose larger address space to userspace")
Reported-by: Yingcong Wu <yingcong.wu@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20230803151609.22141-1-kirill.shutemov%40linux.intel.com
|
|
On platforms with no numa support and with several CPUs, logs have lots
of noise for message "Fail to get numa node for CPU:.."
Change pr_info() to pr_info_once() as one print is enough to show the
issue.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230808174359.50602-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The msi-ec driver fails to build for me (gcc 7.5):
CC [M] drivers/platform/x86/msi-ec.o
drivers/platform/x86/msi-ec.c:72:6: error: initializer element is not constant
{ SM_ECO_NAME, 0xc2 },
^~~~~~~~~~~
drivers/platform/x86/msi-ec.c:72:6: note: (near initialization for ‘CONF0.shift_mode.modes[0].name’)
drivers/platform/x86/msi-ec.c:73:6: error: initializer element is not constant
{ SM_COMFORT_NAME, 0xc1 },
^~~~~~~~~~~~~~~
drivers/platform/x86/msi-ec.c:73:6: note: (near initialization for ‘CONF0.shift_mode.modes[1].name’)
drivers/platform/x86/msi-ec.c:74:6: error: initializer element is not constant
{ SM_SPORT_NAME, 0xc0 },
^~~~~~~~~~~~~
drivers/platform/x86/msi-ec.c:74:6: note: (near initialization for ‘CONF0.shift_mode.modes[2].name’)
(...)
Don't try to be smart, just use defines for the constant strings. The
compiler will recognize it's the same string and will store it only
once in the data section anyway.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 392cacf2aa10 ("platform/x86: Add new msi-ec driver")
Cc: stable@vger.kernel.org
Cc: Nikita Kravets <teackot@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Gross <markgross@kernel.org>
Link: https://lore.kernel.org/r/20230805101010.54d49e91@endymion.delvare
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
On AMD Zen acpi_dev_irq_override() by default prefers the DSDT IRQ 1
settings over the MADT settings.
This causes the keyboard to malfunction on some laptop models
(see Links), all models from the Links have an INT_SRC_OVR MADT entry
for IRQ 1.
Fixes: a9c4a912b7dc ("ACPI: resource: Remove "Zen" specific match and quirks")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217336
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217394
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217406
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
i8042 IRQs
All the cases, were the DSDT IRQ settings should be used instead of
the MADT override, are for IRQ 1 or 12, the PS/2 kbd resp. mouse IRQs.
Simplify things by always honering the override for other legacy IRQs
(for non DMI quirked cases).
This allows removing the DMI quirks to honor the override for
some non i8042 IRQs on some AMD ZEN based Lenovo models.
Fixes: a9c4a912b7dc ("ACPI: resource: Remove "Zen" specific match and quirks")
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit a9c4a912b7dc ("ACPI: resource: Remove "Zen" specific match and
quirks") is causing keyboard problems for quite a log of AMD based
laptop users, leading to many bug reports.
Revert this change for now, until we can come up with
a better fix for the PS/2 IRQ trigger-type/polarity problems
on some x86 laptops.
Fixes: a9c4a912b7dc ("ACPI: resource: Remove "Zen" specific match and quirks")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2228891
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2229165
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2229317
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217718
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217726
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217731
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization.
Commit c5a130325f13 ("ACPI/APEI: Add parameter check before error
injection") exported page_is_ram(), hence the __init annotation should
be removed.
This fixes the modpost warning in ARCH=alpha builds:
WARNING: modpost: vmlinux: page_is_ram: EXPORT_SYMBOL used for init symbol. Remove __init or EXPORT_SYMBOL.
Fixes: c5a130325f13 ("ACPI/APEI: Add parameter check before error injection")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
|
|
The same checks are repeated in three places to decide whether to use
hwrng. Consolidate these into a helper.
Also this fixes a case that one of them was missing a check in the
cleanup path.
Fixes: 554b841d4703 ("tpm: Disable RNG for all AMD fTPMs")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
GDB uses /proc/PID/mem to access memory of the target process. GDB
doesn't untag addresses manually, but relies on kernel to do the right
thing.
mem_rw() of procfs uses access_remote_vm() to get data from the target
process. It worked fine until recent changes in __access_remote_vm()
that now checks if there's VMA at target address using raw address.
Untag the address before looking up the VMA.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Christina Schimpe <christina.schimpe@intel.com>
Fixes: eee9c708cc89 ("gup: avoid stack expansion warning for known-good case")
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the dGPU path instead. There were a lot of platform
issues with IOMMU in general on these chips due to windows
not enabling IOMMU at the time. The dGPU path has been
used for a long time with newer APUs and works fine. This
also paves the way to simplify the driver significantly.
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Tested-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use the dGPU path instead. There were a lot of platform
issues with IOMMU in general on these chips due to windows
not enabling IOMMU at the time. The dGPU path has been
used for a long time with newer APUs and works fine. This
also paves the way to simplify the driver significantly.
v2: use the dGPU queue manager functions
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Tested-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We are dropping the IOMMUv2 path, so no need to enable this.
It's often buggy on consumer platforms anyway.
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Tested-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This is only required for SR-IOV world switches, but it
adds additional latency leading to reduced performance in
some benchmarks. Disable for now on bare metal.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
