| Age | Commit message (Collapse) | Author |
|---|
|
For the little-endian SH771x kernels the driver has to byte-swap the RX/TX
buffers, however yet unset physcial address from the TX descriptor is used
to call sh_eth_soft_swap(). Use 'skb->data' instead...
Fixes: 31fcb99d9958 ("net: sh_eth: remove __flush_purge_region")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David Wilder reported crashes caused by dst reuse.
<quote David>
I am seeing a crash on a distro V4.2.3 kernel caused by a double
release of a dst_entry. In ipv4_dst_destroy() the call to
list_empty() finds a poisoned next pointer, indicating the dst_entry
has already been removed from the list and freed. The crash occurs
18 to 24 hours into a run of a network stress exerciser.
</quote>
Thanks to his detailed report and analysis, we were able to understand
the core issue.
IP early demux can associate a dst to skb, after a lookup in TCP/UDP
sockets.
When socket cache is not properly set, we want to store into
sk->sk_dst_cache the dst for future IP early demux lookups,
by acquiring a stable refcount on the dst.
Problem is this acquisition is simply using an atomic_inc(),
which works well, unless the dst was queued for destruction from
dst_release() noticing dst refcount went to zero, if DST_NOCACHE
was set on dst.
We need to make sure current refcount is not zero before incrementing
it, or risk double free as David reported.
This patch, being a stable candidate, adds two new helpers, and use
them only from IP early demux problematic paths.
It might be possible to merge in net-next skb_dst_force() and
skb_dst_force_safe(), but I prefer having the smallest patch for stable
kernels : Maybe some skb_dst_force() callers do not expect skb->dst
can suddenly be cleared.
Can probably be backported back to linux-3.6 kernels
Reported-by: David J. Wilder <dwilder@us.ibm.com>
Tested-by: David J. Wilder <dwilder@us.ibm.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The way the mode probing works is this:
1. All modes currently on the mode list are marked as UNVERIFIED
2. New modes are on the probed_modes list (they start with
status OK)
3. Modes are moved from the probed_modes list to the actual
mode list. If a mode already on the mode list is deemed
to match one of the probed modes, the duplicate is dropped
and the mode status updated to OK. After this the
probed_modes list will be empty.
4. All modes on the mode list are verified to not violate any
constraints. Any that do are marked as such.
5. Any mode left with a non-OK status is pruned from the list,
with an appropriate debug message.
What all this means is that any mode on the original list that
didn't have a duplicate on the probed_modes list, should be left
with status UNVERFIED (or previously could have been left with
some other status, but never OK).
I broke that in
commit 05acaec334fc ("drm: Reorganize probed mode validation")
by always assigning something to the mode->status during the validation
step. So any mode from the old list that still passed the validation
would be left on the list with status OK in the end.
Fix this by not doing the basic mode validation unless the mode
already has status OK (meaning it came from the probed_modes list,
or at least a duplicate of it was on that list). This way we will
correctly prune away any mode from the old mode list that didn't
appear on the probed_modes list.
Cc: stable@vger.kernel.org
Cc: Adam Jackson <ajax@redhat.com>
Fixes: 05acaec334fc ("drm: Reorganize probed mode validation")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449177255-9515-2-git-send-email-ville.syrjala@linux.intel.com
Testcase: igt/kms_force_connector_basic/prune-stale-modes
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93332
[danvet: Also applying to drm-misc to avoid too much conflict hell -
there's a big pile of patches from Ville on top of this one.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
Here are some i915 fixes for v4.4, sorry for being late this week.
* tag 'drm-intel-fixes-2015-12-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Do a better job at disabling primary plane in the noatomic case.
drm/i915/skl: Double RC6 WRL always on
drm/i915/skl: Disable coarse power gating up until F0
drm/i915: Remove incorrect warning in context cleanup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-fixes
omapdrm fix for 4.4
* tag 'omapdrm-4.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
drm/omap: fix fbdev pix format to support all platforms
|
|
* powercap:
powercap / RAPL: fix BIOS lock check
* pm-cpufreq:
cpufreq: intel_pstate: Minor cleanup for FRAC_BITS
cpufreq: tegra: add regulator dependency for T124
* pm-domains:
PM / Domains: Allow runtime PM callbacks to be re-used during system PM
|
|
Commit 3365711df024 ("sh_eth: WARN on access to a register not implemented in
in a particular chip") added WARN_ON() to sh_eth_{read|write}(), thus making
it unacceptable for these functions to be *inline* anymore. Remove *inline*
and move the functions from the header to the driver itself. Below is our
code economy with ARM gcc 4.7.3:
$ size drivers/net/ethernet/renesas/sh_eth.o{~,}
text data bss dec hex filename
32489 1140 0 33629 835d drivers/net/ethernet/renesas/sh_eth.o~
25413 1140 0 26553 67b9 drivers/net/ethernet/renesas/sh_eth.o
Suggested-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dwmac-sunxi has 2 callbacks that were called from stmmac_platform as
part of the probe and remove sequences.
Ater the conversion of dwmac-sunxi into a standalone platform driver,
the .init function is called before calling into the stmmac driver
core, but .exit is not called to clean up if stmmac returns an error.
This patch fixes the probe error path. This properly cleans up and
releases resources when the driver core fails to probe.
Cc: Joachim Eastwood <manabian@gmail.com>
Fixes: 9a9e9a1edee8 ("stmmac: dwmac-sunxi: turn setup callback into a
probe function")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
郭永刚 reported that one could simply crash the kernel as root by
using a simple program:
int socket_fd;
struct sockaddr_in addr;
addr.sin_port = 0;
addr.sin_addr.s_addr = INADDR_ANY;
addr.sin_family = 10;
socket_fd = socket(10,3,0x40000000);
connect(socket_fd , &addr,16);
AF_INET, AF_INET6 sockets actually only support 8-bit protocol
identifiers. inet_sock's skc_protocol field thus is sized accordingly,
thus larger protocol identifiers simply cut off the higher bits and
store a zero in the protocol fields.
This could lead to e.g. NULL function pointer because as a result of
the cut off inet_num is zero and we call down to inet_autobind, which
is NULL for raw sockets.
kernel: Call Trace:
kernel: [<ffffffff816db90e>] ? inet_autobind+0x2e/0x70
kernel: [<ffffffff816db9a4>] inet_dgram_connect+0x54/0x80
kernel: [<ffffffff81645069>] SYSC_connect+0xd9/0x110
kernel: [<ffffffff810ac51b>] ? ptrace_notify+0x5b/0x80
kernel: [<ffffffff810236d8>] ? syscall_trace_enter_phase2+0x108/0x200
kernel: [<ffffffff81645e0e>] SyS_connect+0xe/0x10
kernel: [<ffffffff81779515>] tracesys_phase2+0x84/0x89
I found no particular commit which introduced this problem.
CVE: CVE-2015-8543
Cc: Cong Wang <cwang@twopensource.com>
Reported-by: 郭永刚 <guoyonggang@360.cn>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mdiobus_alloc() might return NULL, but its return value is not
checked in mdio_mux_init(). This could potentially lead to a NULL
pointer dereference. Fix it by checking the return value
Fixes: 0ca2997d1452 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 33db4125ec74 ("openvswitch: Rename LABEL->LABELS") left
over an old OVS_CT_ATTR_LABEL instance, fix it.
Fixes: 33db4125ec74 ("openvswitch: Rename LABEL->LABELS")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New system call added in
commit a8ca5d0ecbdde5cc3d7accacbd69968b0c98764e
mm: mlock: add new mlock system call
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Pablo Neira Ayuso says:
====================
netfilter fixes for net
The following patchset contains Netfilter fixes for you net tree,
specifically for nf_tables and nfnetlink_queue, they are:
1) Avoid a compilation warning in nfnetlink_queue that was introduced
in the previous merge window with the simplification of the conntrack
integration, from Arnd Bergmann.
2) nfnetlink_queue is leaking the pernet subsystem registration from
a failure path, patch from Nikolay Borisov.
3) Pass down netns pointer to batch callback in nfnetlink, this is the
largest patch and it is not a bugfix but it is a dependency to
resolve a splat in the correct way.
4) Fix a splat due to incorrect socket memory accounting with nfnetlink
skbuff clones.
5) Add missing conntrack dependencies to NFT_DUP_IPV4 and NFT_DUP_IPV6.
6) Traverse the nftables commit list in reverse order from the commit
path, otherwise we crash when the user applies an incremental update
via 'nft -f' that deletes an object that was just introduced in this
batch, from Xin Long.
Regarding the compilation warning fix, many people have sent us (and
keep sending us) patches to address this, that's why I'm including this
batch even if this is not critical.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not doing so is a bug and might trigger a BUG_ON in
handle_mm_fault(). So add the proper permission checks
before calling into mm code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The handle_mm_fault function expects the caller to do the
access checks. Not doing so and calling the function with
wrong permissions is a bug (catched by a BUG_ON).
So fix this bug by adding proper access checking to the io
page-fault code in the AMD IOMMUv2 driver.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Otherwise we keep missing patches related to this driver.
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Using MMUEXT_TLB_FLUSH_MULTI doesn't buy us much since the hypervisor
will likely perform same IPIs as would have the guest.
More importantly, using MMUEXT_INVLPG_MULTI may not to invalidate the
guest's address on remote CPU (when, for example, VCPU from another guest
is running there).
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Currently the provided initial value for bcm2835_gpio_direction_output
has no effect. So fix this issue by changing the value before
changing the GPIO direction. As a result we need to move the function below
bcm2835_gpio_set.
Suggested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Fixes: e1b2dc70cd5b ("pinctrl: add bcm2835 driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Avoid getting sample rate on AudioQuest DragonFly as it is unsupported
and causes noisy "cannot get freq at ep 0x1" messages when playback
starts.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
AudioQuest DragonFly DAC reports a volume control range of 0..50
(0x0000..0x0032) which in USB Audio means a range of 0 .. 0.2dB, which
is obviously incorrect and would cause software using the dB information
in e.g. volume sliders to have a massive volume difference in 100..102%
range.
Commit 2d1cb7f658fb ("ALSA: usb-audio: add dB range mapping for some
devices") added a dB range mapping for it with range 0..50 dB.
However, the actual volume mapping seems to be neither linear volume nor
linear dB scale, but instead quite close to the cubic mapping e.g.
alsamixer uses, with a range of approx. -53...0 dB.
Replace the previous quirk with a custom dB mapping based on some basic
output measurements, using a 10-item range TLV (which will still fit in
alsa-lib MAX_TLV_RANGE_SIZE).
Tested on AudioQuest DragonFly HW v1.2. The quirk is only applied if the
range is 0..50, so if this gets fixed/changed in later HW revisions it
will no longer be applied.
v2: incorporated Takashi Iwai's suggestion for the quirk application
method
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
omap_fbdev always creates a framebuffer with ARGB8888 pixel format. On
OMAP3 we have VIDEO1 overlay that does not support ARGB8888, and on
OMAP2 none of the overlays support ARGB888.
This patch changes the omap_fbdev's fb to XRGB8888, which is supported
by all platforms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The VRF driver cycles netdevs when an interface is enslaved or released:
the down event is used to flush neighbor and route tables and the up
event (if the interface was already up) effectively moves local and
connected routes to the proper table.
As of 4f823defdd5b the local route is left hanging around after a link
down, so when a netdev is moved from one VRF to another (or released
from a VRF altogether) local routes are left in the wrong table.
Fix by handling the NETDEV_CHANGEUPPER event. When the upper dev is
an L3mdev then call fib_disable_ip to flush all routes, local ones
to.
Fixes: 4f823defdd5b ("ipv4: fix to not remove local route on link down")
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
printf() has a dedicated specifier to print MAC addresses. Use it instead of
pushing each byte via stack.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mark address pointer with __iomem in the IO accessors.
Otherwise we will get a sparse complain like following
.../hns/hns_dsaf_reg.h:991:36: warning: incorrect type in argument 1 (different address spaces)
.../hns/hns_dsaf_reg.h:991:36: expected unsigned char [noderef] [usertype] <asn:2>*base
.../hns/hns_dsaf_reg.h:991:36: got void *base
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Jan Stancek reported that I wrecked things for him by fixing things for
Vladimir :/
His report was due to an UNINTERRUPTIBLE wait getting -EINTR, which
should not be possible, however my previous patch made this possible by
unconditionally checking signal_pending().
We cannot use current->state as was done previously, because the
instruction after the store to that variable it can be changed. We must
instead pass the initial state along and use that.
Fixes: 68985633bccb ("sched/wait: Fix signal handling in bit wait helpers")
Reported-by: Jan Stancek <jstancek@redhat.com>
Reported-by: Chris Mason <clm@fb.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Chris Mason <clm@fb.com>
Reviewed-by: Paul Turner <pjt@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: tglx@linutronix.de
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we use 'nft -f' to submit rules, it will build multiple rules into
one netlink skb to send to kernel, kernel will process them one by one.
meanwhile, it add the trans into commit_list to record every commit.
if one of them's return value is -EAGAIN, status |= NFNL_BATCH_REPLAY
will be marked. after all the process is done. it will roll back all the
commits.
now kernel use list_add_tail to add trans to commit, and use
list_for_each_entry_safe to roll back. which means the order of adding
and rollback is the same. that will cause some cases cannot work well,
even trigger call trace, like:
1. add a set into table foo [return -EAGAIN]:
commit_list = 'add set trans'
2. del foo:
commit_list = 'add set trans' -> 'del set trans' -> 'del tab trans'
then nf_tables_abort will be called to roll back:
firstly process 'add set trans':
case NFT_MSG_NEWSET:
trans->ctx.table->use--;
list_del_rcu(&nft_trans_set(trans)->list);
it will del the set from the table foo, but it has removed when del
table foo [step 2], then the kernel will panic.
the right order of rollback should be:
'del tab trans' -> 'del set trans' -> 'add set trans'.
which is opposite with commit_list order.
so fix it by rolling back commits with reverse order in nf_tables_abort.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Pull NFS client bugfix from Trond Myklebust:
"SUNRPC: Fix a NFSv4.1 callback channel regression"
* tag 'nfs-for-4.4-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Fix callback channel
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixlets from Thomas Gleixner:
"Two trivial fixes which add missing header fileas and forward
declarations so the code will compile even when the magic include
chains are different"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Add missing include for barrier.h
irqchip/gic-v3: Add missing struct device_node declaration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix to unbreak a clocksource driver which has more than 32bit
counter width"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Mmio: remove artificial 32bit limitation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull fpga driver fixes from Greg KH:
"Only two small fpga driver fixes here, both have been in linux-next
for a while, and resolve some reported issues"
* tag 'char-misc-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
fpga manager: Fix firmware resource leak on error
fpga manager: remove label
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few staging and IIO driver fixes for 4.4-rc5.
All of them resolve reported problems and have been in linux-next for
a while. Nothing major here, just small fixes where needed"
* tag 'staging-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: lustre: echo_copy.._lsm() dereferences userland pointers directly
iio: adc: spmi-vadc: add missing of_node_put
iio: fix some warning messages
iio: light: apds9960: correct ->last_busy count
iio: lidar: return -EINVAL on invalid signal
staging: iio: dummy: complete IIO events delivery to userspace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are a number of small USB fixes for 4.4-rc5. All of them have
been in linux-next. The majority are gadget and phy issues, with a
few new quirks and device ids added as well"
* tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (32 commits)
USB: add quirk for devices with broken LPM
xhci: fix usb2 resume timing and races.
usb: musb: fail with error when no DMA controller set
usb: gadget: uvc: fix permissions of configfs attributes
usb: musb: core: Fix pm runtime for deferred probe
usb: phy: msm: fix a possible NULL dereference
USB: host: ohci-at91: fix a crash in ohci_hcd_at91_overcurrent_irq
usb: Quiet down false peer failure messages
usb: xhci: fix config fail of FS hub behind a HS hub with MTT
xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()
usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message
USB: whci-hcd: add check for dma mapping error
usb: core : hub: Fix BOS 'NULL pointer' kernel panic
USB: quirks: Apply ALWAYS_POLL to all ELAN devices
usb-storage: Fix scsi-sd failure "Invalid field in cdb" for USB adapter JMicron
USB: quirks: Fix another ELAN touchscreen
usb: dwc3: gadget: don't prestart interrupt endpoints
USB: serial: Another Infineon flash loader USB ID
USB: cdc_acm: Ignore Infineon Flash Loader utility
USB: cp210x: Remove CP2110 ID from compatibility list
...
|
|
A line discipline which does not define a receive_buf() method can
can cause a GPF if data is ever received [1]. Oddly, this was known
to the author of n_tracesink in 2011, but never fixed.
[1] GPF report
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [< (null)>] (null)
PGD 3752d067 PUD 37a7b067 PMD 0
Oops: 0010 [#1] SMP KASAN
Modules linked in:
CPU: 2 PID: 148 Comm: kworker/u10:2 Not tainted 4.4.0-rc2+ #51
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: events_unbound flush_to_ldisc
task: ffff88006da94440 ti: ffff88006db60000 task.ti: ffff88006db60000
RIP: 0010:[<0000000000000000>] [< (null)>] (null)
RSP: 0018:ffff88006db67b50 EFLAGS: 00010246
RAX: 0000000000000102 RBX: ffff88003ab32f88 RCX: 0000000000000102
RDX: 0000000000000000 RSI: ffff88003ab330a6 RDI: ffff88003aabd388
RBP: ffff88006db67c48 R08: ffff88003ab32f9c R09: ffff88003ab31fb0
R10: ffff88003ab32fa8 R11: 0000000000000000 R12: dffffc0000000000
R13: ffff88006db67c20 R14: ffffffff863df820 R15: ffff88003ab31fb8
FS: 0000000000000000(0000) GS:ffff88006dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 0000000037938000 CR4: 00000000000006e0
Stack:
ffffffff829f46f1 ffff88006da94bf8 ffff88006da94bf8 0000000000000000
ffff88003ab31fb0 ffff88003aabd438 ffff88003ab31ff8 ffff88006430fd90
ffff88003ab32f9c ffffed0007557a87 1ffff1000db6cf78 ffff88003ab32078
Call Trace:
[<ffffffff8127cf91>] process_one_work+0x8f1/0x17a0 kernel/workqueue.c:2030
[<ffffffff8127df14>] worker_thread+0xd4/0x1180 kernel/workqueue.c:2162
[<ffffffff8128faaf>] kthread+0x1cf/0x270 drivers/block/aoe/aoecmd.c:1302
[<ffffffff852a7c2f>] ret_from_fork+0x3f/0x70 arch/x86/entry/entry_64.S:468
Code: Bad RIP value.
RIP [< (null)>] (null)
RSP <ffff88006db67b50>
CR2: 0000000000000000
---[ end trace a587f8947e54d6ea ]---
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If an earlycon console driver needs to acquire the uart_port.lock
spinlock for serial console output, and CONFIG_DEBUG_SPINLOCK=y:
BUG: spinlock bad magic on CPU#0, swapper/0
lock: sci_ports+0x0/0x3480, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper Not tainted 4.4.0-rc2-koelsch-g62ea5edf143bb1d0-dirty #2083
Hardware name: Generic R8A7791 (Flattened Device Tree)
[<c00173a0>] (unwind_backtrace) from [<c0013094>] (show_stack+0x10/0x14)
[<c0013094>] (show_stack) from [<c01f2338>] (dump_stack+0x70/0x8c)
[<c01f2338>] (dump_stack) from [<c00702d8>] (do_raw_spin_lock+0x20/0x190)
[<c00702d8>] (do_raw_spin_lock) from [<c0267590>] (serial_console_write+0x4c/0x130)
[<c0267590>] (serial_console_write) from [<c00734c4>] (call_console_drivers.constprop.13+0xc8/0xec)
[<c00734c4>] (call_console_drivers.constprop.13) from [<c0074ef0>] (console_unlock+0x354/0x440)
[<c0074ef0>] (console_unlock) from [<c0075bb4>] (register_console+0x2a0/0x394)
[<c0075bb4>] (register_console) from [<c06cb750>] (of_setup_earlycon+0x90/0xa4)
[<c06cb750>] (of_setup_earlycon) from [<c06cfb60>] (setup_of_earlycon+0x118/0x13c)
[<c06cfb60>] (setup_of_earlycon) from [<c06b34ac>] (do_early_param+0x64/0xb4)
[<c06b34ac>] (do_early_param) from [<c00472c0>] (parse_args+0x254/0x350)
[<c00472c0>] (parse_args) from [<c06b3860>] (parse_early_options+0x2c/0x3c)
[<c06b3860>] (parse_early_options) from [<c06b389c>] (parse_early_param+0x2c/0x40)
[<c06b389c>] (parse_early_param) from [<c06b5b08>] (setup_arch+0x520/0xaf0)
[<c06b5b08>] (setup_arch) from [<c06b3948>] (start_kernel+0x94/0x370)
[<c06b3948>] (start_kernel) from [<40008090>] (0x40008090)
Initialize the spinlock in of_setup_earlycon() and register_earlycon(),
to fix this for both DT-based and legacy earlycon. If the driver would
reinitialize the spinlock again, this is harmless, as it's allowed to
reinitialize an unlocked spinlock.
Alternatives are:
- Drivers having an early_serial_console_write() that only performs
the core functionality of serial_console_write(), without acquiring
the lock (which may be unsafe, depending on the hardware),
- Drivers initializing the spinlock in their private earlycon setup
functions.
As uart_port is owned by generic serial_core, and uart_port.lock is
initialized by uart_add_one_port() for the normal case, this can better
be handled in the earlycon core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes an issue that the "length" of scatterlist should be
set using sg_dma_len(). Otherwise, a dmaengine driver cannot work
correctly if CONFIG_NEED_SG_DMA_LENGTH=y.
Fixes: 7b39d90184 (serial: sh-sci: Fix NULL pointer dereference if HIGHMEM is enabled)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40d5e0905a03 ("n_tty: Fix EOF push handling") fixed EOF push
for reads. However, that approach still allows a condition mismatch
between poll() and read(), where poll() returns POLLIN but read()
blocks. This state can happen when a previous read() returned because
the user buffer was full and the next character was an EOF not at the
beginning of the line. While the next read() will properly identify
the condition and advance the read buffer tail without improperly
indicating an EOF file condition (ie., read() will not mistakenly
return 0), poll() will mistakenly indicate POLLIN.
Although a possible solution would be to peek at the input buffer
in n_tty_poll(), the better solution in this patch is to eat the
EOF during the previous read() (ie., fix the problem by eliminating
the condition).
The current canon line buffer copy limits the scan for next end-of-line
to the smaller of either,
a. the remaining user buffer size
b. completed lines in the input buffer
When the remaining user buffer size is exactly one less than the
end-of-line marked by EOF push, the EOF is not scanned nor skipped
but left for subsequent reads. In the example below, the scan
index 'eol' has stopped at the EOF because it is past the scan
limit of 5 (not because it has found the next set bit in read_flags)
user buffer [*nr = 5] _ _ _ _ _
read_flags 0 0 0 0 0 1
input buffer h e l l o [EOF]
^ ^
/ /
tail eol
result: found = 0, tail += 5, *nr += 5
Instead, allow the scan to peek ahead 1 byte (while still limiting the
scan to completed lines in the input buffer). For the example above,
result: found = 1, tail += 6, *nr += 5
Because the scan limit is now bumped +1 byte, when the scan is
completed, the tail advance and the user buffer copy limit is
re-clamped to *nr when EOF is _not_ found.
Fixes: 40d5e0905a03 ("n_tty: Fix EOF push handling")
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The register offset must be shifted by regshift, otherwise the
baudrate is not set. I missed the issue probably because the
divisor register was already set by the boot loader.
Fixes: 1a8d2903cb6a ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
|
|
DSPI instances in Vybrid have a different amount of chip selects
and CTARs (Clock and transfer Attributes Register). In case of
DSPI1 we only have 2 CTAR registers and 4 CS. In present driver
implementation CTAR offset is derived from CS instance which will
lead to out of bound access if chip select instance is greater than
CTAR register instance, hence use single CTAR0 register for all CS
instances. Since we write the CTAR register anyway before each access,
there is no value in using the additional CTAR registers. Also one
should not program a value in CTAS for a CTAR register that is not
present, hence configure CTAS to use CTAR0.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Trivial typo fix ("mut" -> "must") in the sunxi LRADC-keys binding
documentation.
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- opal-irqchip: Fix double endian conversion from Alistair Popple
- cxl: Set endianess of kernel contexts from Frederic Barrat
- sbc8641: drop bogus PHY IRQ entries from DTS file from Paul Gortmaker
- Revert "powerpc/eeh: Don't unfreeze PHB PE after reset" from Andrew
Donnellan
* tag 'powerpc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
Revert "powerpc/eeh: Don't unfreeze PHB PE after reset"
powerpc/sbc8641: drop bogus PHY IRQ entries from DTS file
cxl: Set endianess of kernel contexts
powerpc/opal-irqchip: Fix double endian conversion
|
|
Merge misc fixes from Andrew Morton:
"17 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MIPS: fix DMA contiguous allocation
sh64: fix __NR_fgetxattr
ocfs2: fix SGID not inherited issue
mm/oom_kill.c: avoid attempting to kill init sharing same memory
drivers/base/memory.c: prohibit offlining of memory blocks with missing sections
tmpfs: fix shmem_evict_inode() warnings on i_blocks
mm/hugetlb.c: fix resv map memory leak for placeholder entries
mm: hugetlb: call huge_pte_alloc() only if ptep is null
kernel: remove stop_machine() Kconfig dependency
mm: kmemleak: mark kmemleak_init prototype as __init
mm: fix kerneldoc on mem_cgroup_replace_page
osd fs: __r4w_get_page rely on PageUptodate for uptodate
MAINTAINERS: make Vladimir co-maintainer of the memory controller
mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress
mm: fix swapped Movable and Reclaimable in /proc/pagetypeinfo
memcg: fix memory.high target
mm: hugetlb: fix hugepage memory leak caused by wrong reserve count
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Fix the boot crash on Mako machines with Huge Pages, prevent a panic
with SATA controllers (and others) by correctly calculating the IOMMU
space, hook up the mlock2 syscall and drop unneeded code in the parisc
pci code"
* 'parisc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Disable huge pages on Mako machines
parisc: Wire up mlock2 syscall
parisc: Remove unused pcibios_init_bus()
parisc iommu: fix panic due to trying to allocate too large region
|
|
Pull block layer fixes from Jens Axboe:
"A set of fixes for the current series. This contains:
- A bunch of fixes for lightnvm, should be the last round for this
series. From Matias and Wenwei.
- A writeback detach inode fix from Ilya, also marked for stable.
- A block (though it says SCSI) fix for an OOPS in SCSI runtime power
management.
- Module init error path fixes for null_blk from Minfei"
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: Fix error path in module initialization
lightnvm: do not compile in debugging by default
lightnvm: prevent gennvm module unload on use
lightnvm: fix media mgr registration
lightnvm: replace req queue with nvmdev for lld
lightnvm: comments on constants
lightnvm: check mm before use
lightnvm: refactor spin_unlock in gennvm_get_blk
lightnvm: put blks when luns configure failed
lightnvm: use flags in rrpc_get_blk
block: detach bdev inode from its wb in __blkdev_put()
SCSI: Fix NULL pointer dereference in runtime PM
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Update the linker script to use L1_CACHE_BYTES instead of hard-coded
64. We recently changed L1_CACHE_BYTES to 128
- Improve race condition reporting on set_pte_at() and change the BUG
to WARN_ONCE. With hardware update of the accessed/dirty state, we
need to ensure that set_pte_at() does not inadvertently override
hardware updated state. The patch also makes the checks ignore
!pte_valid() new entries
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Improve error reporting on set_pte_at() checks
arm64: update linker script to increased L1_CACHE_BYTES value
|
|
Recent changes to how GFP_ATOMIC is defined seems to have broken the
condition to use mips_alloc_from_contiguous() in
mips_dma_alloc_coherent().
I couldn't bottom out the exact change but I think it's this commit
d0164adc89f6 ("mm, page_alloc: distinguish between being unable to
sleep, unwilling to sleep and avoiding waking kswapd").
GFP_ATOMIC has multiple bits set and the check for !(gfp & GFP_ATOMIC)
isn't enough.
The reason behind this condition is to check whether we can potentially
do a sleeping memory allocation. Use gfpflags_allow_blocking() instead
which should be more robust.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
According to arch/sh/kernel/syscalls_64.S and common sense, __NR_fgetxattr
has to be defined to 259, but it doesn't. Instead, it's defined to 269,
which is of course used by another syscall, __NR_sched_setaffinity in this
case.
This bug was found by strace test suite.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 8f1eb48758aa ("ocfs2: fix umask ignored issue") introduced an
issue, SGID of sub dir was not inherited from its parents dir. It is
because SGID is set into "inode->i_mode" in ocfs2_get_init_inode(), but
is overwritten by "mode" which don't have SGID set later.
Fixes: 8f1eb48758aa ("ocfs2: fix umask ignored issue")
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It's possible that an oom killed victim shares an ->mm with the init
process and thus oom_kill_process() would end up trying to kill init as
well.
This has been shown in practice:
Out of memory: Kill process 9134 (init) score 3 or sacrifice child
Killed process 9134 (init) total-vm:1868kB, anon-rss:84kB, file-rss:572kB
Kill process 1 (init) sharing same memory
...
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
And this will result in a kernel panic.
If a process is forked by init and selected for oom kill while still
sharing init_mm, then it's likely this system is in a recoverable state.
However, it's better not to try to kill init and allow the machine to
panic due to unkillable processes.
[rientjes@google.com: rewrote changelog]
[akpm@linux-foundation.org: fix inverted test, per Ben]
Signed-off-by: Chen Jie <chenjie6@huawei.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Li Zefan <lizefan@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
