| Age | Commit message (Collapse) | Author |
|---|
|
As the prototype has been defined in "include/linux/blk-mq.h", the one
in "block/blk-mq.h" can be removed then.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This is to catch any unexpected negative value of inflight IO counter.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Our test reported the following stack, and vmcore showed that
->inflight counter is -1.
[ffffc9003fcc38d0] __schedule at ffffffff8173d95d
[ffffc9003fcc3958] schedule at ffffffff8173de26
[ffffc9003fcc3970] io_schedule at ffffffff810bb6b6
[ffffc9003fcc3988] blkcg_iolatency_throttle at ffffffff813911cb
[ffffc9003fcc3a20] rq_qos_throttle at ffffffff813847f3
[ffffc9003fcc3a48] blk_mq_make_request at ffffffff8137468a
[ffffc9003fcc3b08] generic_make_request at ffffffff81368b49
[ffffc9003fcc3b68] submit_bio at ffffffff81368d7d
[ffffc9003fcc3bb8] ext4_io_submit at ffffffffa031be00 [ext4]
[ffffc9003fcc3c00] ext4_writepages at ffffffffa03163de [ext4]
[ffffc9003fcc3d68] do_writepages at ffffffff811c49ae
[ffffc9003fcc3d78] __filemap_fdatawrite_range at ffffffff811b6188
[ffffc9003fcc3e30] filemap_write_and_wait_range at ffffffff811b6301
[ffffc9003fcc3e60] ext4_sync_file at ffffffffa030cee8 [ext4]
[ffffc9003fcc3ea8] vfs_fsync_range at ffffffff8128594b
[ffffc9003fcc3ee8] do_fsync at ffffffff81285abd
[ffffc9003fcc3f18] sys_fsync at ffffffff81285d50
[ffffc9003fcc3f28] do_syscall_64 at ffffffff81003c04
[ffffc9003fcc3f50] entry_SYSCALL_64_after_swapgs at ffffffff81742b8e
The ->inflight counter may be negative (-1) if
1) blk-iolatency was disabled when the IO was issued,
2) blk-iolatency was enabled before this IO reached its endio,
3) the ->inflight counter is decreased from 0 to -1 in endio()
In fact the hang can be easily reproduced by the below script,
H=/sys/fs/cgroup/unified/
P=/sys/fs/cgroup/unified/test
echo "+io" > $H/cgroup.subtree_control
mkdir -p $P
echo $$ > $P/cgroup.procs
xfs_io -f -d -c "pwrite 0 4k" /dev/sdg
echo "`cat /sys/block/sdg/dev` target=1000000" > $P/io.latency
xfs_io -f -d -c "pwrite 0 4k" /dev/sdg
This fixes the problem by freezing the queue so that while
enabling/disabling iolatency, there is no inflight rq running.
Note that quiesce_queue is not needed as this only updating iolatency
configuration about which dispatching request_queue doesn't care.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull networking fixes from David Miller:
"This pull request is dedicated to the upcoming snowpocalypse parts 2
and 3 in the Pacific Northwest:
1) Drop profiles are broken because some drivers use dev_kfree_skb*
instead of dev_consume_skb*, from Yang Wei.
2) Fix IWLWIFI kconfig deps, from Luca Coelho.
3) Fix percpu maps updating in bpftool, from Paolo Abeni.
4) Missing station release in batman-adv, from Felix Fietkau.
5) Fix some networking compat ioctl bugs, from Johannes Berg.
6) ucc_geth must reset the BQL queue state when stopping the device,
from Mathias Thore.
7) Several XDP bug fixes in virtio_net from Toshiaki Makita.
8) TSO packets must be sent always on queue 0 in stmmac, from Jose
Abreu.
9) Fix socket refcounting bug in RDS, from Eric Dumazet.
10) Handle sparse cpu allocations in bpf selftests, from Martynas
Pumputis.
11) Make sure mgmt frames have enough tailroom in mac80211, from Felix
Feitkau.
12) Use safe list walking in sctp_sendmsg() asoc list traversal, from
Greg Kroah-Hartman.
13) Make DCCP's ccid_hc_[rt]x_parse_options always check for NULL
ccid, from Eric Dumazet.
14) Need to reload WoL password into bcmsysport device after deep
sleeps, from Florian Fainelli.
15) Remove filter from mask before freeing in cls_flower, from Petr
Machata.
16) Missing release and use after free in error paths of s390 qeth
code, from Julian Wiedmann.
17) Fix lockdep false positive in dsa code, from Marc Zyngier.
18) Fix counting of ATU violations in mv88e6xxx, from Andrew Lunn.
19) Fix EQ firmware assert in qed driver, from Manish Chopra.
20) Don't default Caivum PTP to Y in kconfig, from Bjorn Helgaas"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net: dsa: b53: Fix for failure when irq is not defined in dt
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
net: Don't default Cavium PTP driver to 'y'
net: broadcom: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: via-velocity: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: tehuti: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: sun: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: fsl_ucc_hdlc: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: fec_mpc52xx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: smsc: epic100: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: dscc4: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: tulip: de2104x: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: defxx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net/mlx5e: Don't overwrite pedit action when multiple pedit used
net/mlx5e: Update hw flows when encap source mac changed
qed*: Advance drivers version to 8.37.0.20
qed: Change verbosity for coalescing message.
qede: Fix system crash on configuring channels.
qed: Consider TX tcs while deriving the max num_queues for PF.
...
|
|
[Why]
It's useful to know the min and max vrr range for IGT testing.
[How]
Expose the min and max vfreq for the connector via a debugfs file
on the connector, "vrr_range".
Example usage: cat /sys/kernel/debug/dri/0/DP-1/vrr_range
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The entity->dependency can go away completely once we've called
drm_sched_entity_add_dependency_cb() (if the cb is called before we
get around to tracing). The tracepoint is more useful if we trace
every dependency instead of just ones that get callbacks installed,
anyway, so just do that.
Fixes any easy-to-produce OOPS when tracing the scheduler on V3D with
"perf record -a -e gpu_scheduler:.\* glxgears" and DEBUG_SLAB enabled.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some small char and misc driver fixes for 5.0-rc6.
Nothing huge here, some more binderfs fixups found as people use it,
and there is a "large" selftest added to validate the binderfs code,
which makes up the majority of this pull request.
There's also some small mei and mic fixes to resolve some reported
issues.
All of these have been in linux-next for over a week with no reported
issues"
* tag 'char-misc-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mic: vop: Fix crash on remove
mic: vop: Fix use-after-free on remove
binderfs: remove separate device_initcall()
fpga: stratix10-soc: fix wrong of_node_put() in init function
mic: vop: Fix broken virtqueues
mei: free read cb on ctrl_wr list flush
samples: mei: use /dev/mei0 instead of /dev/mei
mei: me: add ice lake point device id.
binderfs: respect limit on binder control creation
binder: fix CONFIG_ANDROID_BINDER_DEVICES
selftests: add binderfs selftests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 5.0-rc6.
Well, not so much "driver core" as "debugfs". There's a lot of
outstanding debugfs cleanup patches coming in through different
subsystem trees, and in that process the debugfs core was found that
it really should return errors when something bad happens, to prevent
random files from showing up in the root of debugfs afterward. So
debugfs was fixed up to handle this properly, and then two fixes for
the relay and blk-mq code was needed as it was making invalid
assumptions about debugfs return values.
There's also a cacheinfo fix in here that resolves a tiny issue.
All of these have been in linux-next for over a week with no reported
problems"
* tag 'driver-core-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
blk-mq: protect debugfs_create_files() from failures
relay: check return of create_buf_file() properly
debugfs: debugfs_lookup() should return NULL if not found
debugfs: return error values, not NULL
debugfs: fix debugfs_rename parameter checking
cacheinfo: Keep the old value if of_property_read_u32 fails
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are some small iio and staging driver fixes for 5.0-rc6.
Nothing big, just resolve some reported IIO driver issues, and one
staging driver bug. One staging driver patch was added and then
reverted as well.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "staging: erofs: keep corrupted fs from crashing kernel in erofs_namei()"
staging: erofs: keep corrupted fs from crashing kernel in erofs_namei()
staging: octeon: fix broken phylib usage
iio: ti-ads8688: Update buffer allocation for timestamps
tools: iio: iio_generic_buffer: make num_loops signed
iio: adc: axp288: Fix TS-pin handling
iio: chemical: atlas-ph-sensor: correct IIO_TEMP values to millicelsius
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial fixes for 5.0-rc6.
Nothing huge, just a few small fixes for reported issues. The speakup
fix is in here as it is a tty operation issue.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: fix race between flush_to_ldisc and tty_open
staging: speakup: fix tty-operation NULL derefs
serial: sh-sci: Do not free irqs that have already been freed
serial: 8250_pci: Make PCI class test non fatal
tty: serial: 8250_mtk: Fix potential NULL pointer dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Grek KH:
"Here are some small USB fixes for 5.0-rc6.
Nothing huge, the normal amount of USB gadget fixes as well as some
USB phy fixes. There's also a typec fix as well. Full details are in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tcpm: Correct the PPS out_volt calculation
usb: gadget: musb: fix short isoc packets with inventra dma
usb: phy: am335x: fix race condition in _probe
usb: dwc3: exynos: Fix error handling of clk_prepare_enable
usb: phy: fix link errors
usb: gadget: udc: net2272: Fix bitwise and boolean operations
usb: dwc3: gadget: Handle 0 xfer length for OUT EP
|
|
Pull xfs fixes from Darrick Wong:
"Here are a handful of XFS fixes to fix a data corruption problem, a
crasher bug, and a deadlock.
Summary:
- Fix cache coherency problem with writeback mappings
- Fix buffer deadlock when shutting fs down
- Fix a null pointer dereference when running online repair"
* tag 'xfs-5.0-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: set buffer ops when repair probes for btree type
xfs: end sync buffer I/O properly on shutdown error
xfs: eof trim writeback mapping as soon as it is cached
|
|
Pull drm fixes from Dave Airlie:
"Missed fixes last week as had nothing until amdgpu showed up on
Saturday. Other stuff has since rolled in along with some more amdgpu
fixes, so we have two weeks of those, and some i915, vmwgfx, sun4i,
rockchip and omap fixes.
amdgpu/radeon:
- fix crash on passthrough for SI
- fencing fix for shared buffers
- APU hwmon fix
- API powerplay fix
- eDP freesync fix
- PASID mgr locking fix
- KFD warning fix
- DC/powerplay fix
- raven revision ids fix
- vega20 doorbell fix
i915:
- SNB display fix
- SKL srckey mask fix
- ICL DDI clock selection fix
vmwgfx:
- DMA API fix
- IOMMU detection fix
- display fixes
sun4i:
- tcon clock fix
rockchip:
- SPDX identifier fix
omap:
- DSI fixes"
* tag 'drm-fixes-2019-02-08' of git://anongit.freedesktop.org/drm/drm: (28 commits)
drm/omap: dsi: Hack-fix DSI bus flags
drm/omap: dsi: Fix OF platform depopulate
drm/omap: dsi: Fix crash in DSI debug dumps
drm/i915: Try to sanitize bogus DPLL state left over by broken SNB BIOSen
drm/amd/display: Attach VRR properties for eDP connectors
drm/amdkfd: Fix if preprocessor statement above kfd_fill_iolink_info_for_cpu
drm/amdgpu: use spin_lock_irqsave to protect vm_manager.pasid_idr
drm/i915: always return something on DDI clock selection
drm/i915: Fix skl srckey mask bits
drm/vmwgfx: Improve on IOMMU detection
drm/vmwgfx: Fix setting of dma masks
drm/vmwgfx: Also check for crtc status while checking for DU active
drm/vmwgfx: Fix an uninitialized fence handle value
drm/vmwgfx: Return error code from vmw_execbuf_copy_fence_user
drm/sun4i: tcon: Prepare and enable TCON channel 0 clock at init
drm/amdgpu: fix the incorrect external id for raven series
drm/amdgpu: Implement doorbell self-ring for NBIO 7.4
drm/amd/display: Fix fclk idle state
drm/amdgpu: Transfer fences to dmabuf importer
drm/amd/powerplay: Fix missing break in switch
...
|
|
In the linux kernel MAINTAINERS file, largely
"xen-devel@lists.xenproject.org (moderated for non-subscribers)"
is used to refer to the xen-devel mailing list.
The DRM DRIVERS FOR XEN section entry mentions
xen-devel@lists.xen.org instead, but that is just the same
mailing list as the mailing list above.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
In the commit 62ba568f7aef ("ALSA: pcm: Return 0 when size <
start_threshold in capture"), we changed the behavior of
__snd_pcm_lib_xfer() to return immediately with 0 when a capture
stream has a high start_threshold. This was intended to be a
correction of the behavior consistency and looked harmless, but this
was the culprit of the recent breakage reported by syzkaller, which
was fixed by the commit e190161f96b8 ("ALSA: pcm: Fix tight loop of
OSS capture stream").
At the time for the OSS fix, I didn't touch the behavior for ALSA
native API, as assuming that this behavior actually is good. But this
turned out to be also broken actually for a similar deployment,
e.g. one thread goes to a write loop in blocking mode while another
thread controls the start/stop of the stream manually.
Overall, the original commit is harmful, and it brings less merit to
keep that behavior. Let's revert it.
Fixes: 62ba568f7aef ("ALSA: pcm: Return 0 when size < start_threshold in capture")
Fixes: e190161f96b8 ("ALSA: pcm: Fix tight loop of OSS capture stream")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The recent commit fe0937b24ff5 ("x86/mm/cpa: Fold cpa_flush_range() and
cpa_flush_array() into a single cpa_flush() function") accidentally made
the call to make_addr_canonical_again() go away, which breaks
set_mce_nospec().
Re-instate the call to convert the address back into canonical form right
before invoking either CLFLUSH or INVLPG. Rename the function while at it
to be shorter (and less MAGA).
Fixes: fe0937b24ff5 ("x86/mm/cpa: Fold cpa_flush_range() and cpa_flush_array() into a single cpa_flush() function")
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tony Luck <tony.luck@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Rik van Riel <riel@surriel.com>
Link: https://lkml.kernel.org/r/20190208120859.GH32511@hirez.programming.kicks-ass.net
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.0
A selection of driver specific fixes here, along with a few core fixes:
- A fixup for some MFD devices that were broken by the previous fixes
for deferred probe.
- A fix for potential out of bounds array accesses when ordering DAPM
power/up down sequences.
- Avoid use after free issue when unloading and reloading drivers using
topologies.
|
|
commit 56222b212e8e ("futex: Drop hb->lock before enqueueing on the
rtmutex") changed the locking rules in the futex code so that the hash
bucket lock is not longer held while the waiter is enqueued into the
rtmutex wait list. This made the lock and the unlock path symmetric, but
unfortunately the possible early exit from __rt_mutex_proxy_start() due to
a detected deadlock was not updated accordingly. That allows a concurrent
unlocker to observe inconsitent state which triggers the warning in the
unlock path.
futex_lock_pi() futex_unlock_pi()
lock(hb->lock)
queue(hb_waiter) lock(hb->lock)
lock(rtmutex->wait_lock)
unlock(hb->lock)
// acquired hb->lock
hb_waiter = futex_top_waiter()
lock(rtmutex->wait_lock)
__rt_mutex_proxy_start()
---> fail
remove(rtmutex_waiter);
---> returns -EDEADLOCK
unlock(rtmutex->wait_lock)
// acquired wait_lock
wake_futex_pi()
rt_mutex_next_owner()
--> returns NULL
--> WARN
lock(hb->lock)
unqueue(hb_waiter)
The problem is caused by the remove(rtmutex_waiter) in the failure case of
__rt_mutex_proxy_start() as this lets the unlocker observe a waiter in the
hash bucket but no waiter on the rtmutex, i.e. inconsistent state.
The original commit handles this correctly for the other early return cases
(timeout, signal) by delaying the removal of the rtmutex waiter until the
returning task reacquired the hash bucket lock.
Treat the failure case of __rt_mutex_proxy_start() in the same way and let
the existing cleanup code handle the eventual handover of the rtmutex
gracefully. The regular rt_mutex_proxy_start() gains the rtmutex waiter
removal for the failure case, so that the other callsites are still
operating correctly.
Add proper comments to the code so all these details are fully documented.
Thanks to Peter for helping with the analysis and writing the really
valuable code comments.
Fixes: 56222b212e8e ("futex: Drop hb->lock before enqueueing on the rtmutex")
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Co-developed-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: Stefan Liebler <stli@linux.ibm.com>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1901292311410.1950@nanos.tec.linutronix.de
|
|
The current comment for the barrier that guarantees that waiter increment
is always before taking the hb spinlock (barrier (A)) needs to be fixed as
it is misplaced.
This is obviously referring to hb_waiters_inc, which is a full barrier.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190206185602.949-1-dave@stgolabs.net
|
|
The kblockd workqueue is created with the WQ_MEM_RECLAIM flag set.
This generates a rescuer thread for that queue that will trigger when
the CPU is under heavy load and collect the uncompleted work.
In the case of mmc, this creates the possibility of a deadlock when
there are multiple partitions on the device as other blk-mq work is
also run on the same queue. For example:
- worker 0 claims the mmc host to work on partition 1
- worker 1 attempts to claim the host for partition 2 but has to wait
for worker 0 to finish
- worker 0 schedules complete_work to release the host
- rescuer thread is triggered after time-out and collects the dangling
work
- rescuer thread attempts to complete the work in order starting with
claim host
- the task to release host is now blocked by a task to claim it and
will never be called
The above results in multiple hung tasks that lead to failures to
mount partitions.
Handling complete_work on a separate workqueue avoids this by keeping
the work completion tasks separate from the other blk-mq work. This
allows the host to be released without getting blocked by other tasks
attempting to claim the host.
Signed-off-by: Zachary Hays <zhays@lexmark.com>
Fixes: 81196976ed94 ("mmc: block: Add blk-mq support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Like Fujitsu CELSIUS H760, the H780 also has a three-button Elantech
touchpad, but the driver needs to be told so to enable the middle touchpad
button.
The elantech_dmi_force_crc_enabled quirk was not necessary with the H780.
Also document the fw_version and caps values detected for both H760 and
H780 models.
Signed-off-by: Matti Kurkela <Matti.Kurkela@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We were enabling autosuspend, which is using data set by the
hash module, prior to the hash module being inited, casuing
a crash on resume as part of the startup sequence if the race
was lost.
This was never a real problem because the PM infra was using low
res timers so we were always winning the race, until commit 8234f6734c5d
("PM-runtime: Switch autosuspend over to using hrtimers") changed that :-)
Fix this by seperating the PM setup and enablement and doing the
latter only at the end of the init sequence.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: stable@kernel.org # v4.20
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fixes the issues with non BCM58XX chips in the b53 driver
failing, when the irq is not specified in the device tree.
Removed the check for BCM58XX in b53_srab_prepare_irq(),
so the 'port->irq' will be set to '-EXIO' if the irq is not
specified in the device tree.
Fixes: 16994374a6fc ("net: dsa: b53: Make SRAB driver manage port interrupts")
Fixes: b2ddc48a81b5 ("net: dsa: b53: Do not fail when IRQ are not initialized")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.0-rc6:
- Fixes to omap/dsi encoder.
- Clock fix for sun4i.
- Licensing header fix for rockchip.
- Fix division by zero in the mode when trying to set a mode on
i915 with GVT-g enabled.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/84462cef-609f-e2af-084a-f9fe2b05c53e@linux.intel.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.0-rc6:
- SNB DPLL sanitize
- ICL DDI clock selection
- SLK srckey mask
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lg2s6nur.fsf@intel.com
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixlet from Darren Hart:
"Correct Documentation/ABI 4.21 KernelVersion to 5.0"
* tag 'platform-drivers-x86-v5.0-2' of git://git.infradead.org/linux-platform-drivers-x86:
Documentation/ABI: Correct mlxreg-io KernelVersion for 5.0
|
|
Pull KVM fixes from Paolo Bonzini:
"Three security fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
|
|
Pull nfsd fixes from Bruce Fields:
"Two small nfsd bugfixes for 5.0, for an RDMA bug and a file clone bug"
* tag 'nfsd-5.0-1' of git://linux-nfs.org/~bfields/linux:
svcrdma: Remove max_sge check at connect time
nfsd: Fix error return values for nfsd4_clone_file_range()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Both of these fixes address issues in changes merged for 5.0-rc4:
- Fix DM core's missing memory barrier before waitqueue_active()
calls.
- Fix DM core's clone_bio() to work when cloning a subset of a bio
with an integrity payload; bio_integrity_trim() wasn't getting
called due to bio_trim()'s early return"
* tag 'for-5.0/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: don't use bio_trim() afterall
dm: add memory barrier before waitqueue_active
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates from Marc Zyngier:
- Another GICv3 ITS fix for devices sharing the same DevID
- Don't return invalid data on exhaustion of the GICv3 LPI pool
- Fix a GICv3 field decoding bug leading to memory over-allocation
- Init GICv4 at boot time instead of lazy init
- Fix interrupt masking on PJ4
|
|
Currently, blktrace will not show requests that don't have any data as
rq->__sector is initialized to -1 which is out of device range and thus
discarded by act_log_check(). This is most notably the case for cache
flush requests sent to the device. Fix the problem by making
blk_rq_trace_sector() return 0 for requests without initialized sector.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Accordingly to the documentation
---cut---
The GCR_ERROR_CAUSE.ERR_TYPE field and the GCR_ERROR_MULT.ERR_TYPE
fields can be cleared by either a reset or by writing the current
value of GCR_ERROR_CAUSE.ERR_TYPE to the
GCR_ERROR_CAUSE.ERR_TYPE register.
---cut---
Do exactly this. Original value of cm_error may be safely written back;
it clears error cause and keeps other bits untouched.
Fixes: 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@linux.intel.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # v4.3+
|
|
On my Yeeloong 8089, I noticed the machine fails to shutdown
properly, and often, the function mach_prepare_reboot() is
unexpectedly executed, thus the machine reboots instead. A
wait loop is needed to ensure the system is in a well-defined
state before going down.
In commit 997e93d4df16 ("MIPS: Hang more efficiently on
halt/powerdown/restart"), a general superset of the wait loop for all
platforms is already provided, so we don't need to implement our own.
This commit simply removes the unreachable() compiler marco after
mach_prepare_reboot(), thus allowing the execution of machine_hang().
My test shows that the machine is now able to shutdown successfully.
Please note that there are two different bugs preventing the machine
from shutting down, another work-in-progress commit is needed to
fix a lockup in cpufreq / i8259 driver, please read Reference, this
commit does not fix that bug.
Reference: https://lkml.org/lkml/2019/2/5/908
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org # v4.17+
|
|
The commit a60945fd08e4 ("ALSA: usb-audio: move implicit fb quirks to
separate function") introduced an error in the handling of quirks for
implicit feedback endpoints. This commit fixes this.
If a quirk successfully sets up an implicit feedback endpoint, usb-audio
no longer tries to find the implicit fb endpoint itself.
Fixes: a60945fd08e4 ("ALSA: usb-audio: move implicit fb quirks to separate function")
Signed-off-by: Manuel Reinhardt <manuel.rhdt@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Hangbin Liu says:
====================
fix two kernel panics when disabled IPv6 on boot up
When disabled IPv6 on boot up, since there is no ipv6 route tables, we should
not call rt6_lookup. Fix them by checking if we have inet6_dev pointer on
netdevice.
v2: Fix idev reference leak, declarations and code mixing as Stefano,
Eric pointed. Since we only want to check if idev exists and not
reference it, use __in6_dev_get() insteand of in6_dev_get().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we disabled IPv6 from the kernel command line (ipv6.disable=1), we should
not call ip6_err_gen_icmpv6_unreach(). This:
ip link add sit1 type sit local 192.0.2.1 remote 192.0.2.2 ttl 1
ip link set sit1 up
ip addr add 198.51.100.1/24 dev sit1
ping 198.51.100.2
if IPv6 is disabled at boot time, will crash the kernel.
v2: there's no need to use in6_dev_get(), use __in6_dev_get() instead,
as we only need to check that idev exists and we are under
rcu_read_lock() (from netif_receive_skb_internal()).
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: ca15a078bd90 ("sit: generate icmpv6 error when receiving icmpv4 error")
Cc: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we add a new GENEVE device with IPv6 remote, checking only for
IS_ENABLED(CONFIG_IPV6) is not enough as we may disable IPv6 in the
kernel command line (ipv6.disable=1), and calling rt6_lookup() would
cause a NULL pointer dereference.
v2:
- don't mix declarations and code (reported by Stefano Brivio, Eric Dumazet)
- there's no need to use in6_dev_get() as we only need to check that
idev exists (reported by David Ahern). This is under RTNL, so we can
simply use __in6_dev_get() instead (Stefano, Eric).
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: c40e89fd358e9 ("geneve: configure MTU based on a lower device")
Cc: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(CVE-2019-7221)
Bugzilla: 1671904
There are multiple code paths where an hrtimer may have been started to
emulate an L1 VMX preemption timer that can result in a call to free_nested
without an intervening L2 exit where the hrtimer is normally
cancelled. Unconditionally cancel in free_nested to cover all cases.
Embargoed until Feb 7th 2019.
Signed-off-by: Peter Shier <pshier@google.com>
Reported-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reported-by: Felix Wilhelm <fwilhelm@google.com>
Cc: stable@kernel.org
Message-Id: <20181011184646.154065-1-pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Bugzilla: 1671930
Emulation of certain instructions (VMXON, VMCLEAR, VMPTRLD, VMWRITE with
memory operand, INVEPT, INVVPID) can incorrectly inject a page fault
when passed an operand that points to an MMIO address. The page fault
will use uninitialized kernel stack memory as the CR2 and error code.
The right behavior would be to abort the VM with a KVM_EXIT_INTERNAL_ERROR
exit to userspace; however, it is not an easy fix, so for now just
ensure that the error code and CR2 are zero.
Embargoed until Feb 7th 2019.
Reported-by: Felix Wilhelm <fwilhelm@google.com>
Cc: stable@kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm_ioctl_create_device() does the following:
1. creates a device that holds a reference to the VM object (with a borrowed
reference, the VM's refcount has not been bumped yet)
2. initializes the device
3. transfers the reference to the device to the caller's file descriptor table
4. calls kvm_get_kvm() to turn the borrowed reference to the VM into a real
reference
The ownership transfer in step 3 must not happen before the reference to the VM
becomes a proper, non-borrowed reference, which only happens in step 4.
After step 3, an attacker can close the file descriptor and drop the borrowed
reference, which can cause the refcount of the kvm object to drop to zero.
This means that we need to grab a reference for the device before
anon_inode_getfd(), otherwise the VM can disappear from under us.
Fixes: 852b6d57dc7f ("kvm: add device control API")
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This enables mute LED support and fixes switching jacks when the laptop
is docked.
Signed-off-by: Jurica Vukadin <jurica.vukadin@rt-rk.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We need to reset MCU and do other initializations on resume otherwise
MT7610U device will fail to initialize, what cause system hung due to
USB requests timeouts.
Patch fixes 4.19 -> 4.20 regression.
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If we have a kernel configured for periodic timer interrupts, and we
have cpuidle enabled, then we end up with CPU1 losing timer interupts
after a hotplug.
This can manifest itself in RCU stall warnings, or userspace becoming
unresponsive.
The problem is that the kernel initially wants to use the TWD timer
for interrupts, but the TWD loses context when we enter the C3 cpuidle
state. Nothing reprograms the TWD after idle.
We have solved this in the past by switching to broadcast timer ticks,
and cpuidle44xx switches to that mode at boot time. However, there is
nothing to switch from periodic mode local timers after a hotplug
operation.
We call tick_broadcast_enter() in omap_enter_idle_coupled(), which one
would expect would take care of the issue, but internally this only
deals with one-shot local timers - tick_broadcast_enable() on the other
hand only deals with periodic local timers. So, we need to call both.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: just standardized the subject line]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Recently syzkaller was able to create unkillablle processes by
creating a timer that is delivered as a thread local signal on SIGHUP,
and receiving SIGHUP SA_NODEFERER. Ultimately causing a loop failing
to deliver SIGHUP but always trying.
When the stack overflows delivery of SIGHUP fails and force_sigsegv is
called. Unfortunately because SIGSEGV is numerically higher than
SIGHUP next_signal tries again to deliver a SIGHUP.
From a quality of implementation standpoint attempting to deliver the
timer SIGHUP signal is wrong. We should attempt to deliver the
synchronous SIGSEGV signal we just forced.
We can make that happening in a fairly straight forward manner by
instead of just looking at the signal number we also look at the
si_code. In particular for exceptions (aka synchronous signals) the
si_code is always greater than 0.
That still has the potential to pick up a number of asynchronous
signals as in a few cases the same si_codes that are used
for synchronous signals are also used for asynchronous signals,
and SI_KERNEL is also included in the list of possible si_codes.
Still the heuristic is much better and timer signals are definitely
excluded. Which is enough to prevent all known ways for someone
sending a process signals fast enough to cause unexpected and
arguably incorrect behavior.
Cc: stable@vger.kernel.org
Fixes: a27341cd5fcb ("Prioritize synchronous signals over 'normal' signals")
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
Recently syzkaller was able to create unkillablle processes by
creating a timer that is delivered as a thread local signal on SIGHUP,
and receiving SIGHUP SA_NODEFERER. Ultimately causing a loop
failing to deliver SIGHUP but always trying.
Upon examination it turns out part of the problem is actually most of
the solution. Since 2.5 signal delivery has found all fatal signals,
marked the signal group for death, and queued SIGKILL in every threads
thread queue relying on signal->group_exit_code to preserve the
information of which was the actual fatal signal.
The conversion of all fatal signals to SIGKILL results in the
synchronous signal heuristic in next_signal kicking in and preferring
SIGHUP to SIGKILL. Which is especially problematic as all
fatal signals have already been transformed into SIGKILL.
Instead of dequeueing signals and depending upon SIGKILL to
be the first signal dequeued, first test if the signal group
has already been marked for death. This guarantees that
nothing in the signal queue can prevent a process that needs
to exit from exiting.
Cc: stable@vger.kernel.org
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Ref: ebf5ebe31d2c ("[PATCH] signal-fixes-2.5.59-A4")
History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
This patch moves clk_get_rate() call from trigger() to hw_params()
callback to avoid calling sleeping clk API from atomic context
and prevent deadlock as indicated below.
Before this change clk_get_rate() was being called with same
spinlock held as the one passed to the clk API when registering
clocks exposed by the I2S driver.
[ 82.109780] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:908
[ 82.117009] in_atomic(): 1, irqs_disabled(): 128, pid: 1554, name: speaker-test
[ 82.124235] 3 locks held by speaker-test/1554:
[ 82.128653] #0: cc8c5328 (snd_pcm_link_rwlock){...-}, at: snd_pcm_stream_lock_irq+0x20/0x38
[ 82.137058] #1: ec9eda17 (&(&substream->self_group.lock)->rlock){..-.}, at: snd_pcm_ioctl+0x900/0x1268
[ 82.146417] #2: 6ac279bf (&(&pri_dai->spinlock)->rlock){..-.}, at: i2s_trigger+0x64/0x6d4
[ 82.154650] irq event stamp: 8144
[ 82.157949] hardirqs last enabled at (8143): [<c0a0f574>] _raw_read_unlock_irq+0x24/0x5c
[ 82.166089] hardirqs last disabled at (8144): [<c0a0f6a8>] _raw_read_lock_irq+0x18/0x58
[ 82.174063] softirqs last enabled at (8004): [<c01024e4>] __do_softirq+0x3a4/0x66c
[ 82.181688] softirqs last disabled at (7997): [<c012d730>] irq_exit+0x140/0x168
[ 82.188964] Preemption disabled at:
[ 82.188967] [<00000000>] (null)
[ 82.195728] CPU: 6 PID: 1554 Comm: speaker-test Not tainted 5.0.0-rc5-00192-ga6e6caca8f03 #191
[ 82.204302] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 82.210376] [<c0111a54>] (unwind_backtrace) from [<c010d8f4>] (show_stack+0x10/0x14)
[ 82.218084] [<c010d8f4>] (show_stack) from [<c09ef004>] (dump_stack+0x90/0xc8)
[ 82.225278] [<c09ef004>] (dump_stack) from [<c0152980>] (___might_sleep+0x22c/0x2c8)
[ 82.232990] [<c0152980>] (___might_sleep) from [<c0a0a2e4>] (__mutex_lock+0x28/0xa3c)
[ 82.240788] [<c0a0a2e4>] (__mutex_lock) from [<c0a0ad80>] (mutex_lock_nested+0x1c/0x24)
[ 82.248763] [<c0a0ad80>] (mutex_lock_nested) from [<c04923dc>] (clk_prepare_lock+0x78/0xec)
[ 82.257079] [<c04923dc>] (clk_prepare_lock) from [<c049538c>] (clk_core_get_rate+0xc/0x5c)
[ 82.265309] [<c049538c>] (clk_core_get_rate) from [<c0766b18>] (i2s_trigger+0x490/0x6d4)
[ 82.273369] [<c0766b18>] (i2s_trigger) from [<c074fec4>] (soc_pcm_trigger+0x100/0x140)
[ 82.281254] [<c074fec4>] (soc_pcm_trigger) from [<c07378a0>] (snd_pcm_do_start+0x2c/0x30)
[ 82.289400] [<c07378a0>] (snd_pcm_do_start) from [<c07376cc>] (snd_pcm_action_single+0x38/0x78)
[ 82.298065] [<c07376cc>] (snd_pcm_action_single) from [<c073a450>] (snd_pcm_ioctl+0x910/0x1268)
[ 82.306734] [<c073a450>] (snd_pcm_ioctl) from [<c0292344>] (do_vfs_ioctl+0x90/0x9ec)
[ 82.314443] [<c0292344>] (do_vfs_ioctl) from [<c0292cd4>] (ksys_ioctl+0x34/0x60)
[ 82.321808] [<c0292cd4>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
[ 82.329431] Exception stack(0xeb875fa8 to 0xeb875ff0)
[ 82.334459] 5fa0: 00033c18 b6e31000 00000004 00004142 00033d80 00033d80
[ 82.342605] 5fc0: 00033c18 b6e31000 00008000 00000036 00008000 00000000 beea38a8 00008000
[ 82.350748] 5fe0: b6e3142c beea384c b6da9a30 b6c9212c
[ 82.355789]
[ 82.357245] ======================================================
[ 82.363397] WARNING: possible circular locking dependency detected
[ 82.369551] 5.0.0-rc5-00192-ga6e6caca8f03 #191 Tainted: G W
[ 82.376395] ------------------------------------------------------
[ 82.382548] speaker-test/1554 is trying to acquire lock:
[ 82.387834] 6d2007f4 (prepare_lock){+.+.}, at: clk_prepare_lock+0x78/0xec
[ 82.394593]
[ 82.394593] but task is already holding lock:
[ 82.400398] 6ac279bf (&(&pri_dai->spinlock)->rlock){..-.}, at: i2s_trigger+0x64/0x6d4
[ 82.408197]
[ 82.408197] which lock already depends on the new lock.
[ 82.416343]
[ 82.416343] the existing dependency chain (in reverse order) is:
[ 82.423795]
[ 82.423795] -> #1 (&(&pri_dai->spinlock)->rlock){..-.}:
[ 82.430472] clk_mux_set_parent+0x34/0xb8
[ 82.434975] clk_core_set_parent_nolock+0x1c4/0x52c
[ 82.440347] clk_set_parent+0x38/0x6c
[ 82.444509] of_clk_set_defaults+0xc8/0x308
[ 82.449186] of_clk_add_provider+0x84/0xd0
[ 82.453779] samsung_i2s_probe+0x408/0x5f8
[ 82.458376] platform_drv_probe+0x48/0x98
[ 82.462879] really_probe+0x224/0x3f4
[ 82.467037] driver_probe_device+0x70/0x1c4
[ 82.471716] bus_for_each_drv+0x44/0x8c
[ 82.476049] __device_attach+0xa0/0x138
[ 82.480382] bus_probe_device+0x88/0x90
[ 82.484715] deferred_probe_work_func+0x6c/0xbc
[ 82.489741] process_one_work+0x200/0x740
[ 82.494246] worker_thread+0x2c/0x4c8
[ 82.498408] kthread+0x128/0x164
[ 82.502131] ret_from_fork+0x14/0x20
[ 82.506204] (null)
[ 82.508976]
[ 82.508976] -> #0 (prepare_lock){+.+.}:
[ 82.514264] __mutex_lock+0x60/0xa3c
[ 82.518336] mutex_lock_nested+0x1c/0x24
[ 82.522756] clk_prepare_lock+0x78/0xec
[ 82.527088] clk_core_get_rate+0xc/0x5c
[ 82.531421] i2s_trigger+0x490/0x6d4
[ 82.535494] soc_pcm_trigger+0x100/0x140
[ 82.539913] snd_pcm_do_start+0x2c/0x30
[ 82.544246] snd_pcm_action_single+0x38/0x78
[ 82.549012] snd_pcm_ioctl+0x910/0x1268
[ 82.553345] do_vfs_ioctl+0x90/0x9ec
[ 82.557417] ksys_ioctl+0x34/0x60
[ 82.561229] ret_fast_syscall+0x0/0x28
[ 82.565477] 0xbeea384c
[ 82.568421]
[ 82.568421] other info that might help us debug this:
[ 82.568421]
[ 82.576394] Possible unsafe locking scenario:
[ 82.576394]
[ 82.582285] CPU0 CPU1
[ 82.586792] ---- ----
[ 82.591297] lock(&(&pri_dai->spinlock)->rlock);
[ 82.595977] lock(prepare_lock);
[ 82.601782] lock(&(&pri_dai->spinlock)->rlock);
[ 82.608975] lock(prepare_lock);
[ 82.612268]
[ 82.612268] *** DEADLOCK ***
Fixes: 647d04f8e07a ("ASoC: samsung: i2s: Ensure the RCLK rate is properly determined")
Reported-by: Krzysztof Kozłowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently "0xf << 36" is used to
clear SSIU-9 internal buffer state, which overflows 32-bit value
according to user reference manual, it is always bit4 ~ bit7
of SSI_SYS_STATUS[1,3,5,7] registers indicate
SSIU-9's buffer state, so "0xf << 4" should be used.
This patch fix incorrect shifting issue in SSIU-9 case
Fixes: commit b7169ddea2f2 ("ASoC: rsnd: remove RSND_REG_ from rsnd_reg")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fix from Jiri Kosina:
"A fix for a bug in hid-debug that can lock up the kernel in infinite
loop (CVE-2019-3819), from Vladis Dronov"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: debug: fix the ring buffer implementation
|
|
On systems with VHE the kernel and KVM's world-switch code run at the
same exception level. Code that is only used on a VHE system does not
need to be annotated as __hyp_text as it can reside anywhere in the
kernel text.
__hyp_text was also used to prevent kprobes from patching breakpoint
instructions into this region, as this code runs at a different
exception level. While this is no longer true with VHE, KVM still
switches VBAR_EL1, meaning a kprobe's breakpoint executed in the
world-switch code will cause a hyp-panic.
echo "p:weasel sysreg_save_guest_state_vhe" > /sys/kernel/debug/tracing/kprobe_events
echo 1 > /sys/kernel/debug/tracing/events/kprobes/weasel/enable
lkvm run -k /boot/Image --console serial -p "console=ttyS0 earlycon=uart,mmio,0x3f8"
# lkvm run -k /boot/Image -m 384 -c 3 --name guest-1474
Info: Placing fdt at 0x8fe00000 - 0x8fffffff
Info: virtio-mmio.devices=0x200@0x10000:36
Info: virtio-mmio.devices=0x200@0x10200:37
Info: virtio-mmio.devices=0x200@0x10400:38
[ 614.178186] Kernel panic - not syncing: HYP panic:
[ 614.178186] PS:404003c9 PC:ffff0000100d70e0 ESR:f2000004
[ 614.178186] FAR:0000000080080000 HPFAR:0000000000800800 PAR:1d00007edbadc0de
[ 614.178186] VCPU:00000000f8de32f1
[ 614.178383] CPU: 2 PID: 1482 Comm: kvm-vcpu-0 Not tainted 5.0.0-rc2 #10799
[ 614.178446] Call trace:
[ 614.178480] dump_backtrace+0x0/0x148
[ 614.178567] show_stack+0x24/0x30
[ 614.178658] dump_stack+0x90/0xb4
[ 614.178710] panic+0x13c/0x2d8
[ 614.178793] hyp_panic+0xac/0xd8
[ 614.178880] kvm_vcpu_run_vhe+0x9c/0xe0
[ 614.178958] kvm_arch_vcpu_ioctl_run+0x454/0x798
[ 614.179038] kvm_vcpu_ioctl+0x360/0x898
[ 614.179087] do_vfs_ioctl+0xc4/0x858
[ 614.179174] ksys_ioctl+0x84/0xb8
[ 614.179261] __arm64_sys_ioctl+0x28/0x38
[ 614.179348] el0_svc_common+0x94/0x108
[ 614.179401] el0_svc_handler+0x38/0x78
[ 614.179487] el0_svc+0x8/0xc
[ 614.179558] SMP: stopping secondary CPUs
[ 614.179661] Kernel Offset: disabled
[ 614.179695] CPU features: 0x003,2a80aa38
[ 614.179758] Memory Limit: none
[ 614.179858] ---[ end Kernel panic - not syncing: HYP panic:
[ 614.179858] PS:404003c9 PC:ffff0000100d70e0 ESR:f2000004
[ 614.179858] FAR:0000000080080000 HPFAR:0000000000800800 PAR:1d00007edbadc0de
[ 614.179858] VCPU:00000000f8de32f1 ]---
Annotate the VHE world-switch functions that aren't marked
__hyp_text using NOKPROBE_SYMBOL().
Signed-off-by: James Morse <james.morse@arm.com>
Fixes: 3f5c90b890ac ("KVM: arm64: Introduce VHE-specific kvm_vcpu_run")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We restrict mapping the PUD huge pages in stage2 to only when the
stage2 has 4 level page table, leaving the feature unused with
the default IPA size. But we could use it even with a 3
level page table, i.e, when the PUD level is folded into PGD,
just like the stage1. Relax the condition to allow using the
PUD huge page mappings at stage2 when it is possible.
Cc: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
