| Age | Commit message (Collapse) | Author |
|---|
|
Sudarsana Reddy Kalluru says:
====================
qed*: PTP bug fixes.
The series addresses couple of issues in the PTP implementation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PTP hardware filter configuration performed by the driver for a given
user requested config is not correct for some of the PTP modes.
Following changes are needed for PTP config-filter implementation.
1. NIG_REG_TX_PTP_EN register - Bits 0/1/2 respectively enables
TimeSync/"V1 frame format support"/"V2 frame format support" on
the TX side. Set the associated bits based on the user request.
2. ptp4l application fails to operate in Peer Delay mode. Following
changes are needed to fix this,
a. Driver should enable (set to 0) DA #1-related bits for IPv4,
IPv6 and MAC destination addresses in these registers:
NIG_REG_TX_LLH_PTP_RULE_MASK
NIG_REG_LLH_PTP_RULE_MASK
b. NIG_REG_LLH_PTP_PARAM_MASK/NIG_REG_TX_LLH_PTP_PARAM_MASK should
be set to 0x0 in all modes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PTP Tx timestamping data structures are not protected against the
concurrent access in the Tx paths. Protecting the same using atomic
bit locks.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IOT2000 is industrial controller platform, derived from the Intel
Galileo Gen2 board. The variant IOT2020 comes with one LAN port, the
IOT2040 has two of them. They can be told apart based on the board asset
tag in the DMI table.
Based on patch by Sascha Weisenberger.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hns_get_sset_count() returns HNS_NET_STATS_CNT and the data space allocated
is not enough for ethtool_get_strings(), which will cause random memory
corruption.
When SLAB and DEBUG_SLAB are both enabled, memory corruptions like the
the following can be observed without this patch:
[ 43.115200] Slab corruption (Not tainted): Acpi-ParseExt start=ffff801fb0b69030, len=80
[ 43.115206] Redzone: 0x9f911029d006462/0x5f78745f31657070.
[ 43.115208] Last user: [<5f7272655f746b70>](0x5f7272655f746b70)
[ 43.115214] 010: 70 70 65 31 5f 74 78 5f 70 6b 74 00 6b 6b 6b 6b ppe1_tx_pkt.kkkk
[ 43.115217] 030: 70 70 65 31 5f 74 78 5f 70 6b 74 5f 6f 6b 00 6b ppe1_tx_pkt_ok.k
[ 43.115218] Next obj: start=ffff801fb0b69098, len=80
[ 43.115220] Redzone: 0x706d655f6f666966/0x9f911029d74e35b.
[ 43.115229] Last user: [<ffff0000084b11b0>](acpi_os_release_object+0x28/0x38)
[ 43.115231] 000: 74 79 00 6b 6b 6b 6b 6b 70 70 65 31 5f 74 78 5f ty.kkkkkppe1_tx_
[ 43.115232] 010: 70 6b 74 5f 65 72 72 5f 63 73 75 6d 5f 66 61 69 pkt_err_csum_fai
Signed-off-by: Timmy Li <lixiaoping3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Be careful when comparing tcp_time_stamp to some u32 quantity,
otherwise result can be surprising.
Fixes: 7c106d7e782b ("[TCP]: TCP Low Priority congestion control")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the instruction right before the branch destination is
a 64 bit load immediate, we currently calculate the wrong
jump offset in the ctx->offset[] array as we only account
one instruction slot for the 64 bit load immediate although
it uses two BPF instructions. Fix it up by setting the offset
into the right slot after we incremented the index.
Before (ldimm64 test 1):
[...]
00000020: 52800007 mov w7, #0x0 // #0
00000024: d2800060 mov x0, #0x3 // #3
00000028: d2800041 mov x1, #0x2 // #2
0000002c: eb01001f cmp x0, x1
00000030: 54ffff82 b.cs 0x00000020
00000034: d29fffe7 mov x7, #0xffff // #65535
00000038: f2bfffe7 movk x7, #0xffff, lsl #16
0000003c: f2dfffe7 movk x7, #0xffff, lsl #32
00000040: f2ffffe7 movk x7, #0xffff, lsl #48
00000044: d29dddc7 mov x7, #0xeeee // #61166
00000048: f2bdddc7 movk x7, #0xeeee, lsl #16
0000004c: f2ddddc7 movk x7, #0xeeee, lsl #32
00000050: f2fdddc7 movk x7, #0xeeee, lsl #48
[...]
After (ldimm64 test 1):
[...]
00000020: 52800007 mov w7, #0x0 // #0
00000024: d2800060 mov x0, #0x3 // #3
00000028: d2800041 mov x1, #0x2 // #2
0000002c: eb01001f cmp x0, x1
00000030: 540000a2 b.cs 0x00000044
00000034: d29fffe7 mov x7, #0xffff // #65535
00000038: f2bfffe7 movk x7, #0xffff, lsl #16
0000003c: f2dfffe7 movk x7, #0xffff, lsl #32
00000040: f2ffffe7 movk x7, #0xffff, lsl #48
00000044: d29dddc7 mov x7, #0xeeee // #61166
00000048: f2bdddc7 movk x7, #0xeeee, lsl #16
0000004c: f2ddddc7 movk x7, #0xeeee, lsl #32
00000050: f2fdddc7 movk x7, #0xeeee, lsl #48
[...]
Also, add a couple of test cases to make sure JITs pass
this test. Tested on Cavium ThunderX ARMv8. The added
test cases all pass after the fix.
Fixes: 8eee539ddea0 ("arm64: bpf: fix out-of-bounds read in bpf2a64_offset()")
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This work adds BPF_XADD for BPF_W/BPF_DW to the arm64 JIT and therefore
completes JITing of all BPF instructions, meaning we can thus also remove
the 'notyet' label and do not need to fall back to the interpreter when
BPF_XADD is used in a program!
This now also brings arm64 JIT in line with x86_64, s390x, ppc64, sparc64,
where all current eBPF features are supported.
BPF_W example from test_bpf:
.u.insns_int = {
BPF_ALU32_IMM(BPF_MOV, R0, 0x12),
BPF_ST_MEM(BPF_W, R10, -40, 0x10),
BPF_STX_XADD(BPF_W, R10, R0, -40),
BPF_LDX_MEM(BPF_W, R0, R10, -40),
BPF_EXIT_INSN(),
},
[...]
00000020: 52800247 mov w7, #0x12 // #18
00000024: 928004eb mov x11, #0xffffffffffffffd8 // #-40
00000028: d280020a mov x10, #0x10 // #16
0000002c: b82b6b2a str w10, [x25,x11]
// start of xadd mapping:
00000030: 928004ea mov x10, #0xffffffffffffffd8 // #-40
00000034: 8b19014a add x10, x10, x25
00000038: f9800151 prfm pstl1strm, [x10]
0000003c: 885f7d4b ldxr w11, [x10]
00000040: 0b07016b add w11, w11, w7
00000044: 880b7d4b stxr w11, w11, [x10]
00000048: 35ffffab cbnz w11, 0x0000003c
// end of xadd mapping:
[...]
BPF_DW example from test_bpf:
.u.insns_int = {
BPF_ALU32_IMM(BPF_MOV, R0, 0x12),
BPF_ST_MEM(BPF_DW, R10, -40, 0x10),
BPF_STX_XADD(BPF_DW, R10, R0, -40),
BPF_LDX_MEM(BPF_DW, R0, R10, -40),
BPF_EXIT_INSN(),
},
[...]
00000020: 52800247 mov w7, #0x12 // #18
00000024: 928004eb mov x11, #0xffffffffffffffd8 // #-40
00000028: d280020a mov x10, #0x10 // #16
0000002c: f82b6b2a str x10, [x25,x11]
// start of xadd mapping:
00000030: 928004ea mov x10, #0xffffffffffffffd8 // #-40
00000034: 8b19014a add x10, x10, x25
00000038: f9800151 prfm pstl1strm, [x10]
0000003c: c85f7d4b ldxr x11, [x10]
00000040: 8b07016b add x11, x11, x7
00000044: c80b7d4b stxr w11, x11, [x10]
00000048: 35ffffab cbnz w11, 0x0000003c
// end of xadd mapping:
[...]
Tested on Cavium ThunderX ARMv8, test suite results after the patch:
No JIT: [ 3751.855362] test_bpf: Summary: 311 PASSED, 0 FAILED, [0/303 JIT'ed]
With JIT: [ 3573.759527] test_bpf: Summary: 311 PASSED, 0 FAILED, [303/303 JIT'ed]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull fs/compat.c cleanups from Al Viro:
"More moving of compat syscalls from fs/compat.c to fs/*.c where the
native counterparts live.
And death to compat_sys_getdents64() - the only architecture that used
to need it was ia64, and _that_ has lost biarch support quite a few
years ago"
* 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs/compat.c: trim unused includes
move compat_rw_copy_check_uvector() over to fs/read_write.c
fhandle: move compat syscalls from compat.c
open: move compat syscalls from compat.c
stat: move compat syscalls from compat.c
fcntl: move compat syscalls from compat.c
readdir: move compat syscalls from compat.c
statfs: move compat syscalls from compat.c
utimes: move compat syscalls from compat.c
move compat select-related syscalls to fs/select.c
Remove compat_sys_getdents64()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull splice updates from Al Viro:
"These actually missed the last cycle; the branch itself is from last
December"
* 'work.splice' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make nr_pages calculation in default_file_splice_read() a bit less ugly
splice/tee/vmsplice: validate flags
splice_pipe_desc: kill ->flags
remove spd_release_page()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull iov_iter updates from Al Viro:
"Cleanups that sat in -next + -stable fodder that has just missed 4.11.
There's more iov_iter work in my local tree, but I'd prefer to push
the stuff that had been in -next first"
* 'work.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
iov_iter: don't revert iov buffer if csum error
generic_file_read_iter(): make use of iov_iter_revert()
generic_file_direct_write(): make use of iov_iter_revert()
orangefs: use iov_iter_revert()
sctp: switch to copy_from_iter_full()
net/9p: switch to copy_from_iter_full()
switch memcpy_from_msg() to copy_from_iter_full()
rds: make use of iov_iter_revert()
|
|
Pull CIFS fixes from Steve French:
"Three cifs/smb3 fixes - including two for stable"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs: don't check for failure from mempool_alloc()
Do not return number of bytes written for ioctl CIFS_IOC_COPYCHUNK_FILE
Fix match_prepath()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardened usercopy updates from Kees Cook:
"A couple hardened usercopy changes:
- drop now unneeded is_vmalloc_or_module() check (Laura Abbott)
- use enum instead of literals for stack frame API (Sahara)"
* tag 'usercopy-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
mm/usercopy: Drop extra is_vmalloc_or_module() check
usercopy: Move enum for arch_within_stack_frames()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"This has a large internal refactoring along with several smaller
fixes.
- constify compression structures; Bhumika Goyal
- restore powerpc dumping; Ankit Kumar
- fix more bugs in the rarely exercises module unloading logic
- reorganize filesystem locking to fix problems noticed by lockdep
- refactor internal pstore APIs to make development and review
easier:
- improve error reporting
- add kernel-doc structure and function comments
- avoid insane argument passing by using a common record
structure"
* tag 'pstore-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (23 commits)
pstore: Solve lockdep warning by moving inode locks
pstore: Fix flags to enable dumps on powerpc
pstore: Remove unused vmalloc.h in pmsg
pstore: simplify write_user_compat()
pstore: Remove write_buf() callback
pstore: Replace arguments for write_buf_user() API
pstore: Replace arguments for write_buf() API
pstore: Replace arguments for erase() API
pstore: Do not duplicate record metadata
pstore: Allocate records on heap instead of stack
pstore: Pass record contents instead of copying
pstore: Always allocate buffer for decompression
pstore: Replace arguments for write() API
pstore: Replace arguments for read() API
pstore: Switch pstore_mkfile to pass record
pstore: Move record decompression to function
pstore: Extract common arguments into structure
pstore: Add kernel-doc for struct pstore_info
pstore: Improve register_pstore() error reporting
pstore: Avoid race in module unloading
...
|
|
Pull documentation update from Jonathan Corbet:
"A reasonably busy cycle for documentation this time around. There is a
new guide for user-space API documents, rather sparsely populated at
the moment, but it's a start. Markus improved the infrastructure for
converting diagrams. Mauro has converted much of the USB documentation
over to RST. Plus the usual set of fixes, improvements, and tweaks.
There's a bit more than the usual amount of reaching out of
Documentation/ to fix comments elsewhere in the tree; I have acks for
those where I could get them"
* tag 'docs-4.12' of git://git.lwn.net/linux: (74 commits)
docs: Fix a couple typos
docs: Fix a spelling error in vfio-mediated-device.txt
docs: Fix a spelling error in ioctl-number.txt
MAINTAINERS: update file entry for HSI subsystem
Documentation: allow installing man pages to a user defined directory
Doc/PM: Sync with intel_powerclamp code behavior
zr364xx.rst: usb/devices is now at /sys/kernel/debug/
usb.rst: move documentation from proc_usb_info.txt to USB ReST book
convert philips.txt to ReST and add to media docs
docs-rst: usb: update old usbfs-related documentation
arm: Documentation: update a path name
docs: process/4.Coding.rst: Fix a couple of document refs
docs-rst: fix usb cross-references
usb: gadget.h: be consistent at kernel doc macros
usb: composite.h: fix two warnings when building docs
usb: get rid of some ReST doc build errors
usb.rst: get rid of some Sphinx errors
usb/URB.txt: convert to ReST and update it
usb/persist.txt: convert to ReST and add to driver-api book
usb/hotplug.txt: convert to ReST and add to driver-api book
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- more kernel message modernizations and cleanups
- Mac and Nubus improvements and cleanups.
* tag 'm68k-for-v4.12-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
nubus: Add MVC and VSC video card definitions
nubus: Clean up whitespace
nubus: Clean up printk calls
nubus: Fix nubus_rewinddir
m68k/mac: Clarify IOP message alloc/free confusion
m68k/mac: Adopt platform_device_register_simple()
m68k/mac: Modernize printing of kernel messages
m68k/mac: IOP - Modernize printing of kernel messages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- three merges for KVM/s390 with changes for vfio-ccw and cpacf. The
patches are included in the KVM tree as well, let git sort it out.
- add the new 'trng' random number generator
- provide the secure key verification API for the pkey interface
- introduce the z13 cpu counters to perf
- add a new system call to set up the guarded storage facility
- simplify TASK_SIZE and arch_get_unmapped_area
- export the raw STSI data related to CPU topology to user space
- ... and the usual churn of bug-fixes and cleanups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (74 commits)
s390/crypt: use the correct module alias for paes_s390.
s390/cpacf: Introduce kma instruction
s390/cpacf: query instructions use unique parameters for compatibility with KMA
s390/trng: Introduce s390 TRNG device driver.
s390/crypto: Provide s390 specific arch random functionality.
s390/crypto: Add new subfunctions to the cpacf PRNO function.
s390/crypto: Renaming PPNO to PRNO.
s390/pageattr: avoid unnecessary page table splitting
s390/mm: simplify arch_get_unmapped_area[_topdown]
s390/mm: make TASK_SIZE independent from the number of page table levels
s390/gs: add regset for the guarded storage broadcast control block
s390/kvm: Add use_cmma field to mm_context_t
s390/kvm: Add PGSTE manipulation functions
vfio: ccw: improve error handling for vfio_ccw_mdev_remove
vfio: ccw: remove unnecessary NULL checks of a pointer
s390/spinlock: remove compare and delay instruction
s390/spinlock: use atomic primitives for spinlocks
s390/cpumf: simplify detection of guest samples
s390/pci: remove forward declaration
s390/pci: increase the PCI_NR_FUNCTIONS default
...
|
|
I say:
====================
Fix some bpf program testing framework bugs
This series fixes two issue:
1) Accidental user pointer dereference in bpf_test_finish()
2) The packet data given to the test programs is not aligned correctly
The first issue is fixed simply because we have a kernel side copy
of the datastructure in question already. And the second bug is
a simple matter of applying NET_IP_ALIGN where needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure we apply NET_IP_ALIGN when reserving headroom for SKB
and XDP test runs, just like a real driver would.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Instead, pass the kattr in which has a kernel side copy of this
data structure from userspace already.
Fix based upon a suggestion from Alexei Starovoitov.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This fixes the testcase on big-endian.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix kdoc parameter spelling from extact to extack.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following warnings triggered by 51570a5ab2b7 ("A Sample of
using socket cookie and uid for traffic monitoring"):
In file included from /home/foo/net-next/samples/bpf/cookie_uid_helper_example.c:54:0:
/home/foo/net-next/samples/bpf/cookie_uid_helper_example.c: In function 'prog_load':
/home/foo/net-next/samples/bpf/cookie_uid_helper_example.c:119:27: warning: overflow in implicit constant conversion [-Woverflow]
-32 + offsetof(struct stats, uid)),
^
/home/foo/net-next/samples/bpf/libbpf.h:135:12: note: in definition of macro 'BPF_STX_MEM'
.off = OFF, \
^
/home/foo/net-next/samples/bpf/cookie_uid_helper_example.c:121:27: warning: overflow in implicit constant conversion [-Woverflow]
-32 + offsetof(struct stats, packets), 1),
^
/home/foo/net-next/samples/bpf/libbpf.h:155:12: note: in definition of macro 'BPF_ST_MEM'
.off = OFF, \
^
/home/foo/net-next/samples/bpf/cookie_uid_helper_example.c:129:27: warning: overflow in implicit constant conversion [-Woverflow]
-32 + offsetof(struct stats, bytes)),
^
/home/foo/net-next/samples/bpf/libbpf.h:135:12: note: in definition of macro 'BPF_STX_MEM'
.off = OFF, \
^
HOSTLD /home/foo/net-next/samples/bpf/per_socket_stats_example
Fixes: 51570a5ab2b7 ("A Sample of using socket cookie and uid for traffic monitoring")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
'for-4.12/cp2112', 'for-4.12/hid-core-null-state-handling', 'for-4.12/hiddev', 'for-4.12/i2c-hid', 'for-4.12/innomedia', 'for-4.12/logitech-hidpp-battery-power-supply', 'for-4.12/multitouch', 'for-4.12/nti', 'for-4.12/upstream' and 'for-4.12/wacom' into for-linus
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm updates from Ingo Molnar:
"The main x86 MM changes in this cycle were:
- continued native kernel PCID support preparation patches to the TLB
flushing code (Andy Lutomirski)
- various fixes related to 32-bit compat syscall returning address
over 4Gb in applications, launched from 64-bit binaries - motivated
by C/R frameworks such as Virtuozzo. (Dmitry Safonov)
- continued Intel 5-level paging enablement: in particular the
conversion of x86 GUP to the generic GUP code. (Kirill A. Shutemov)
- x86/mpx ABI corner case fixes/enhancements (Joerg Roedel)
- ... plus misc updates, fixes and cleanups"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (62 commits)
mm, zone_device: Replace {get, put}_zone_device_page() with a single reference to fix pmem crash
x86/mm: Fix flush_tlb_page() on Xen
x86/mm: Make flush_tlb_mm_range() more predictable
x86/mm: Remove flush_tlb() and flush_tlb_current_task()
x86/vm86/32: Switch to flush_tlb_mm_range() in mark_screen_rdonly()
x86/mm/64: Fix crash in remove_pagetable()
Revert "x86/mm/gup: Switch GUP to the generic get_user_page_fast() implementation"
x86/boot/e820: Remove a redundant self assignment
x86/mm: Fix dump pagetables for 4 levels of page tables
x86/mpx, selftests: Only check bounds-vs-shadow when we keep shadow
x86/mpx: Correctly report do_mpx_bt_fault() failures to user-space
Revert "x86/mm/numa: Remove numa_nodemask_from_meminfo()"
x86/espfix: Add support for 5-level paging
x86/kasan: Extend KASAN to support 5-level paging
x86/mm: Add basic defines/helpers for CONFIG_X86_5LEVEL=y
x86/paravirt: Add 5-level support to the paravirt code
x86/mm: Define virtual memory map for 5-level paging
x86/asm: Remove __VIRTUAL_MASK_SHIFT==47 assert
x86/boot: Detect 5-level paging support
x86/mm/numa: Remove numa_nodemask_from_meminfo()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 vdso updates from Ingo Molnar:
"Add support for vDSO acceleration of the "Hyper-V TSC page", to speed
up clock reading on Hyper-V guests"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Add VCLOCK_HVCLOCK vDSO clock read method
x86/hyperv: Move TSC reading method to asm/mshyperv.h
x86/hyperv: Implement hv_get_tsc_page()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 platform updates from Ingo Molnar:
"Most of the commits are continued SGI UV4 hardware-enablement changes,
plus there's also new Bluetooth support for the Intel Edison platform"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/intel-mid: Enable Bluetooth support on Intel Edison
x86/platform/uv/BAU: Implement uv4_wait_completion with read_status
x86/platform/uv/BAU: Add wait_completion to bau_operations
x86/platform/uv/BAU: Add status mmr location fields to bau_control
x86/platform/uv/BAU: Cleanup bau_operations declaration and instances
x86/platform/uv/BAU: Add payload descriptor qualifier
x86/platform/uv/BAU: Add uv_bau_version enumerated constants
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq update from Ingo Molnar:
"A single commit that micro-optimizes an IRQ vectors code path in the
CPU offlining code"
* 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Optimize free vector check in the CPU offline path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 debug updates from Ingo Molnar:
"The biggest update is the addition of USB3 debug port based
early-console.
Greg was fine with the USB changes and with the routing of these
patches:
https://www.spinics.net/lists/linux-usb/msg155093.html"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
usb/doc: Add document for USB3 debug port usage
usb/serial: Add DBC debug device support to usb_debug
x86/earlyprintk: Add support for earlyprintk via USB3 debug port
usb/early: Add driver for xhci debug capability
x86/timers: Add simple udelay calibration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanups from Ingo Molnar:
"A handful of small cleanups"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Remove a redundant #ifdef directive
x86/smp: Remove the redundant #ifdef CONFIG_SMP directive
x86/smp: Reduce code duplication
x86/pci-calgary: Use setup_timer() instead of open coding it.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 build update from Ingo Molnar:
"A single CLang support related fix"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kbuild: Use cc-option to enable -falign-{jumps/loops}
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- unwinder fixes and enhancements
- improve ftrace interaction with the unwinder
- optimize the code footprint of WARN() and related debugging
constructs
- ... plus misc updates, cleanups and fixes"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/unwind: Dump all stacks in unwind_dump()
x86/unwind: Silence more entry-code related warnings
x86/ftrace: Fix ebp in ftrace_regs_caller that screws up unwinder
x86/unwind: Remove unused 'sp' parameter in unwind_dump()
x86/unwind: Prepend hex mask value with '0x' in unwind_dump()
x86/unwind: Properly zero-pad 32-bit values in unwind_dump()
x86/unwind: Ensure stack pointer is aligned
debug: Avoid setting BUGFLAG_WARNING twice
x86/unwind: Silence entry-related warnings
x86/unwind: Read stack return address in update_stack_state()
x86/unwind: Move common code into update_stack_state()
debug: Fix __bug_table[] in arch linker scripts
debug: Add _ONCE() logic to report_bug()
x86/debug: Define BUG() again for !CONFIG_BUG
x86/debug: Implement __WARN() using UD0
x86/ftrace: Use Makefile logic instead of #ifdef for compiling ftrace_*.o
x86/ftrace: Add -mfentry support to x86_32 with DYNAMIC_FTRACE set
x86/ftrace: Clean up ftrace_regs_caller
x86/ftrace: Add stack frame pointer to ftrace_caller
x86/ftrace: Move the ftrace specific code out of entry_32.S
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic updates from Ingo Molnar:
"Two small cleanups"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Fix a comment in init_apic_mappings()
x86/apic: Remove the SET_APIC_ID(x) macro
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cpu updates from Ingo Molnar:
"The biggest changes are an extension of the Intel RDT code to extend
it with Intel Memory Bandwidth Allocation CPU support: MBA allows
bandwidth allocation between cores, while CBM (already upstream)
allows CPU cache partitioning.
There's also misc smaller fixes and updates"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/intel_rdt: Return error for incorrect resource names in schemata
x86/intel_rdt: Trim whitespace while parsing schemata input
x86/intel_rdt: Fix padding when resource is enabled via mount
x86/intel_rdt: Get rid of anon union
x86/cpu: Keep model defines sorted by model number
x86/intel_rdt/mba: Add schemata file support for MBA
x86/intel_rdt: Make schemata file parsers resource specific
x86/intel_rdt/mba: Add info directory files for Memory Bandwidth Allocation
x86/intel_rdt: Make information files resource specific
x86/intel_rdt/mba: Add primary support for Memory Bandwidth Allocation (MBA)
x86/intel_rdt/mba: Memory bandwith allocation feature detect
x86/intel_rdt: Add resource specific msr update function
x86/intel_rdt: Move CBM specific data into a struct
x86/intel_rdt: Cleanup namespace to support multiple resource types
Documentation, x86: Intel Memory bandwidth allocation
x86/intel_rdt: Organize code properly
x86/intel_rdt: Init padding only if a device exists
x86/intel_rdt: Add cpus_list rdtgroup file
x86/intel_rdt: Cleanup kernel-doc
x86/intel_rdt: Update schemata read to show data in tabular format
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 boot updates from Ingo Molnar:
"The biggest changes in this cycle were:
- reworking of the e820 code: separate in-kernel and boot-ABI data
structures and apply a whole range of cleanups to the kernel side.
No change in functionality.
- enable KASLR by default: it's used by all major distros and it's
out of the experimental stage as well.
- ... misc fixes and cleanups"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (63 commits)
x86/KASLR: Fix kexec kernel boot crash when KASLR randomization fails
x86/reboot: Turn off KVM when halting a CPU
x86/boot: Fix BSS corruption/overwrite bug in early x86 kernel startup
x86: Enable KASLR by default
boot/param: Move next_arg() function to lib/cmdline.c for later reuse
x86/boot: Fix Sparse warning by including required header file
x86/boot/64: Rename start_cpu()
x86/xen: Update e820 table handling to the new core x86 E820 code
x86/boot: Fix pr_debug() API braindamage
xen, x86/headers: Add <linux/device.h> dependency to <asm/xen/page.h>
x86/boot/e820: Simplify e820__update_table()
x86/boot/e820: Separate the E820 ABI structures from the in-kernel structures
x86/boot/e820: Fix and clean up e820_type switch() statements
x86/boot/e820: Rename the remaining E820 APIs to the e820__*() prefix
x86/boot/e820: Remove unnecessary #include's
x86/boot/e820: Rename e820_mark_nosave_regions() to e820__register_nosave_regions()
x86/boot/e820: Rename e820_reserve_resources*() to e820__reserve_resources*()
x86/boot/e820: Use bool in query APIs
x86/boot/e820: Document e820__reserve_setup_data()
x86/boot/e820: Clean up __e820__update_table() et al
...
|
|
Like other JITs, sparc64 maintains an array of instruction offsets but
stores the entries off by one. This is done because jumps to the
exit block are indexed to one past the last BPF instruction.
So if we size the array by the program length, we need to record
the previous instruction in order to stay within the array bounds.
This is explained in ARM JIT commit 8eee539ddea0 ("arm64: bpf: fix
out-of-bounds read in bpf2a64_offset()").
But this scheme requires a little bit of careful handling when
the instruction before the branch destination is a 64-bit load
immediate. It takes up 2 BPF instruction slots.
Therefore, we have to fill in the array entry for the second
half of the 64-bit load immediate instruction rather than for
the one for the beginning of that instruction.
Fixes: 7a12b5031c6b ("sparc64: Add eBPF JIT.")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS updates from Ingo Molnar:
"The main changes in this cycle were:
- add the 'Corrected Errors Collector' kernel feature which collect
and monitor correctable errors statistics and will preemptively
(soft-)offline physical pages that have a suspiciously high error
count.
- handle MCE errors during kexec() more gracefully
- factor out and deprecate the /dev/mcelog driver
- ... plus misc fixes and cleanpus"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Check MCi_STATUS[MISCV] for usable addr on Intel only
ACPI/APEI: Use setup_deferrable_timer()
x86/mce: Update notifier priority check
x86/mce: Enable PPIN for Knights Landing/Mill
x86/mce: Do not register notifiers with invalid prio
x86/mce: Factor out and deprecate the /dev/mcelog driver
RAS: Add a Corrected Errors Collector
x86/mce: Rename mce_log to mce_log_buffer
x86/mce: Rename mce_log()'s argument
x86/mce: Init some CPU features early
x86/mce: Handle broadcasted MCE gracefully with kexec
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- Kprobes and uprobes changes:
- Make their trampolines read-only while they are used
- Make UPROBES_EVENTS default-y which is the distro practice
- Apply misc fixes and robustization to probe point insertion.
- add support for AMD IOMMU events
- extend hw events on Intel Goldmont CPUs
- ... plus misc fixes and updates.
Tooling side changes:
- support s390 jump instructions in perf annotate (Christian
Borntraeger)
- vendor hardware events updates (Andi Kleen)
- add argument support for SDT events in powerpc (Ravi Bangoria)
- beautify the statx syscall arguments in 'perf trace' (Arnaldo
Carvalho de Melo)
- handle inline functions in callchains (Jin Yao)
- enable sorting by srcline as key (Milian Wolff)
- add 'brstackinsn' field in 'perf script' to reuse the x86
instruction decoder used in the Intel PT code to study hot paths to
samples (Andi Kleen)
- add PERF_RECORD_NAMESPACES so that the kernel can record
information required to associate samples to namespaces, helping in
container problem characterization. (Hari Bathini)
- allow sorting by symbol_size in 'perf report' and 'perf top'
(Charles Baylis)
- in perf stat, make system wide (-a) the default option if no target
was specified and one of following conditions is met:
- no workload specified (current behaviour)
- a workload is specified but all requested events are system wide
ones, like uncore ones. (Jiri Olsa)
- ... plus lots of other updates, enhancements, cleanups and fixes"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (235 commits)
perf tools: Fix the code to strip command name
tools arch x86: Sync cpufeatures.h
tools arch: Sync arch/x86/lib/memcpy_64.S with the kernel
tools: Update asm-generic/mman-common.h copy from the kernel
perf tools: Use just forward declarations for struct thread where possible
perf tools: Add the right header to obtain PERF_ALIGN()
perf tools: Remove poll.h and wait.h from util.h
perf tools: Remove string.h, unistd.h and sys/stat.h from util.h
perf tools: Remove stale prototypes from builtin.h
perf tools: Remove string.h from util.h
perf tools: Remove sys/ioctl.h from util.h
perf tools: Remove a few more needless includes from util.h
perf tools: Include sys/param.h where needed
perf callchain: Move callchain specific routines from util.[ch]
perf tools: Add compress.h for the *_decompress_to_file() headers
perf mem: Fix display of data source snoop indication
perf debug: Move dump_stack() and sighandler_dump_stack() to debug.h
perf kvm: Make function only used by 'perf kvm' static
perf tools: Move timestamp routines from util.h to time-utils.h
perf tools: Move units conversion/formatting routines to separate object
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pul x86/process updates from Ingo Molnar:
"The main change in this cycle was to add the ARCH_[GET|SET]_CPUID
prctl() ABI extension to control the availability of the CPUID
instruction, analogously to the existing PR_GET|SET_TSC ABI that
controls RDTSC.
Motivation: the 'rr' user-space record-and-replay execution debugger
would like to trap and emulate the CPUID instruction - which
instruction is normally unprivileged.
Trapping CPUID is possible on IvyBridge and later Intel CPUs - expose
this hardware capability"
* 'x86-process-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/syscalls/32: Ignore arch_prctl for other architectures
um/arch_prctl: Fix fallout from x86 arch_prctl() rework
x86/arch_prctl: Add ARCH_[GET|SET]_CPUID
x86/cpufeature: Detect CPUID faulting support
x86/syscalls/32: Wire up arch_prctl on x86-32
x86/arch_prctl: Add do_arch_prctl_common()
x86/arch_prctl/64: Rename do_arch_prctl() to do_arch_prctl_64()
x86/arch_prctl/64: Use SYSCALL_DEFINE2 to define sys_arch_prctl()
x86/arch_prctl: Rename 'code' argument to 'option'
x86/msr: Rename MISC_FEATURE_ENABLES to MISC_FEATURES_ENABLES
x86/process: Optimize TIF_NOTSC switch
x86/process: Correct and optimize TIF_BLOCKSTEP switch
x86/process: Optimize TIF checks in __switch_to_xtra()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- a big round of FUTEX_UNLOCK_PI improvements, fixes, cleanups and
general restructuring
- lockdep updates such as new checks for lock_downgrade()
- introduce the new atomic_try_cmpxchg() locking API and use it to
optimize refcount code generation
- ... plus misc fixes, updates and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
MAINTAINERS: Add FUTEX SUBSYSTEM
futex: Clarify mark_wake_futex memory barrier usage
futex: Fix small (and harmless looking) inconsistencies
futex: Avoid freeing an active timer
rtmutex: Plug preempt count leak in rt_mutex_futex_unlock()
rtmutex: Fix more prio comparisons
rtmutex: Fix PI chain order integrity
sched,tracing: Update trace_sched_pi_setprio()
sched/rtmutex: Refactor rt_mutex_setprio()
rtmutex: Clean up
sched/deadline/rtmutex: Dont miss the dl_runtime/dl_period update
sched/rtmutex/deadline: Fix a PI crash for deadline tasks
rtmutex: Deboost before waking up the top waiter
locking/ww-mutex: Limit stress test to 2 seconds
locking/atomic: Fix atomic_try_cmpxchg() semantics
lockdep: Fix per-cpu static objects
futex: Drop hb->lock before enqueueing on the rtmutex
futex: Futex_unlock_pi() determinism
futex: Rework futex_lock_pi() to use rt_mutex_*_proxy_lock()
futex,rt_mutex: Restructure rt_mutex_finish_proxy_lock()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- another round of rq-clock handling debugging, robustization and
fixes
- PELT accounting improvements
- CPU hotplug related ->cpus_allowed affinity handling fixes all
around the tree
- ... plus misc fixes, cleanups and updates"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (35 commits)
sched/x86: Update reschedule warning text
crypto: N2 - Replace racy task affinity logic
cpufreq/sparc-us2e: Replace racy task affinity logic
cpufreq/sparc-us3: Replace racy task affinity logic
cpufreq/sh: Replace racy task affinity logic
cpufreq/ia64: Replace racy task affinity logic
ACPI/processor: Replace racy task affinity logic
ACPI/processor: Fix error handling in __acpi_processor_start()
sparc/sysfs: Replace racy task affinity logic
powerpc/smp: Replace open coded task affinity logic
ia64/sn/hwperf: Replace racy task affinity logic
ia64/salinfo: Replace racy task affinity logic
workqueue: Provide work_on_cpu_safe()
ia64/topology: Remove cpus_allowed manipulation
sched/fair: Move the PELT constants into a generated header
sched/fair: Increase PELT accuracy for small tasks
sched/fair: Fix comments
sched/Documentation: Add 'sched-pelt' tool
sched/fair: Fix corner case in __accumulate_sum()
sched/core: Remove 'task' parameter and rename tsk_restore_flags() to current_restore_flags()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- move BGRT handling to drivers/acpi so it can be shared between x86
and ARM
- bring the EFI stub's initrd and FDT allocation logic in line with
the latest changes to the arm64 boot protocol
- improvements and fixes to the EFI stub's command line parsing
routines
- randomize the virtual mapping of the UEFI runtime services on
ARM/arm64
- ... and other misc enhancements, cleanups and fixes"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm: Don't use TASK_SIZE when randomizing the RT space
ef/libstub/arm/arm64: Randomize the base of the UEFI rt services region
efi/libstub/arm/arm64: Disable debug prints on 'quiet' cmdline arg
efi/libstub: Unify command line param parsing
efi/libstub: Fix harmless command line parsing bug
efi/arm32-stub: Allow boot-time allocations in the vmlinux region
x86/efi: Clean up a minor mistake in comment
efi/pstore: Return error code (if any) from efi_pstore_write()
efi/bgrt: Enable ACPI BGRT handling on arm64
x86/efi/bgrt: Move efi-bgrt handling out of arch/x86
efi/arm-stub: Round up FDT allocation to mapping size
efi/arm-stub: Correct FDT and initrd allocation rules for arm64
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Nothing exciting from the irq side for this merge window:
- a new driver for a Mediatek SoC
- ACPI support for ARM GICV3
- support for shared nested interrupts
- the usual pile of fixes and updates all over te place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
irqchip/mbigen: Fix return value check in mbigen_device_probe()
irqchip/mips-gic: Replace static map with dynamic
irqchip/mips-gic: Remove device IRQ domain
irqchip/mips-gic: Separate IPI reservation & usage tracking
genirq: Use irqd_get_trigger_type to compare the trigger type for shared IRQs
genirq: Use cpumask_available() for check of cpumask variable
cpumask: Add helper cpumask_available()
irqchip/irq-imx-gpcv2: Clear OF_POPULATED flag
irqchip/atmel-aic5: Handle suspend to RAM
irqchip: Add Mediatek mtk-cirq driver
dt-bindings: mtk-cirq: Add binding document
irqchip/gic-v3-its: Add IORT hook for platform MSI support
irqchip/mbigen: Add ACPI support
irqchip/mbigen: Introduce mbigen_of_create_domain()
irqchip/mbigen: Drop module owner
platform-msi: Make platform_msi_create_device_domain() ACPI aware
irqchip/gicv3-its: platform-msi: Scan MADT to create platform msi domain
irqchip/gicv3-its: platform-msi: Refactor its_pmsi_init() to prepare for ACPI
irqchip/gicv3-its: platform-msi: Refactor its_pmsi_prepare()
irqchip/gic-v3-its: Keep the include header files in alphabetic order
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32
Pull AVR32 removal from Hans-Christian Noren Egtvedt:
"This will remove support for AVR32 architecture from the kernel and
clean away the most obvious architecture related parts. Removing dead
code in drivers is the next step"
Notes from previous discussion about this:
"The AVR32 architecture is not keeping up with the development of the
kernel, and since it shares so much of the drivers with Atmel ARM SoC,
it is starting to hinder these drivers to develop swiftly.
Also, all AVR32 AP7 SoC processors are end of lifed from Atmel (now
Microchip).
Finally, the GCC toolchain is stuck at version 4.2.x, and has not
received any patches since the last release from Atmel;
4.2.4-atmel.1.1.3.avr32linux.1.
When building kernel v4.10, this toolchain is no longer able to
properly link the network stack.
Haavard and I have came to the conclusion that we feel keeping AVR32
on life support offers more obstacles for Atmel ARMs, than it gives
joy to AVR32 users. I also suspect there are very few AVR32 users left
today, if anybody at all"
That discussion was acked by Andy Shevchenko, Boris Brezillon, Nicolas
Ferre, and Haavard Skinnemoen.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
mm: remove AVR32 arch special handling in mm/Kconfig
lib: remove check for AVR32 arch in test_user_copy
lib: remove AVR32 entry in Kconfig.debug compile with frame pointers
scripts: remove AVR32 support from checkstack.pl
docs: remove all references to AVR32 architecture
avr32: remove support for AVR32 architecture
|
|
Starting from gcc-5.4+ gcc generates MLX instructions in more cases to
refer local symbols:
https://gcc.gnu.org/PR60465
That caused ia64 module loader to choke on such instructions:
fuse: invalid slot number 1 for IMM64
The Linux kernel used to handle only case where relocation pointed to
slot=2 instruction in the bundle. That limitation was fixed in linux by
commit 9c184a073bfd ("[IA64] Fix 2.6 kernel for the new ia64 assembler")
See
http://sources.redhat.com/bugzilla/show_bug.cgi?id=1433
This change lifts the slot=2 restriction from the kernel module loader.
Tested on 'fuse' and 'btrfs' kernel modules.
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: H J Lu <hjl.tools@gmail.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Bug: https://bugs.gentoo.org/601014
Tested-by: Émeric MASCHINO <emeric.maschino@gmail.com>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uaccess unification updates from Al Viro:
"This is the uaccess unification pile. It's _not_ the end of uaccess
work, but the next batch of that will go into the next cycle. This one
mostly takes copy_from_user() and friends out of arch/* and gets the
zero-padding behaviour in sync for all architectures.
Dealing with the nocache/writethrough mess is for the next cycle;
fortunately, that's x86-only. Same for cleanups in iov_iter.c (I am
sold on access_ok() in there, BTW; just not in this pile), same for
reducing __copy_... callsites, strn*... stuff, etc. - there will be a
pile about as large as this one in the next merge window.
This one sat in -next for weeks. -3KLoC"
* 'work.uaccess' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (96 commits)
HAVE_ARCH_HARDENED_USERCOPY is unconditional now
CONFIG_ARCH_HAS_RAW_COPY_USER is unconditional now
m32r: switch to RAW_COPY_USER
hexagon: switch to RAW_COPY_USER
microblaze: switch to RAW_COPY_USER
get rid of padding, switch to RAW_COPY_USER
ia64: get rid of copy_in_user()
ia64: sanitize __access_ok()
ia64: get rid of 'segment' argument of __do_{get,put}_user()
ia64: get rid of 'segment' argument of __{get,put}_user_check()
ia64: add extable.h
powerpc: get rid of zeroing, switch to RAW_COPY_USER
esas2r: don't open-code memdup_user()
alpha: fix stack smashing in old_adjtimex(2)
don't open-code kernel_setsockopt()
mips: switch to RAW_COPY_USER
mips: get rid of tail-zeroing in primitives
mips: make copy_from_user() zero tail explicitly
mips: clean and reorder the forest of macros...
mips: consolidate __invoke_... wrappers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull generic device properties framework updates from Rafael Wysocki:
"These add support for the ports and endpoints concepts, based on the
existing DT support for them, to the generic device properties
framework and update the ACPI _DSD properties code to recognize ports
and endpoints accordingly.
Specifics:
- Extend the ACPI _DSD properties code and the generic device
properties framework to support the concept of remote endponts
(Mika Westerberg, Sakari Ailus).
- Document the support for ports and endpoints in _DSD properties and
extend the generic device properties framework to make it more
suitable for the handling of ports and endpoints (Sakari Ailus)"
* tag 'devprop-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Read strings using string array reading functions
device property: fwnode_property_read_string_array() returns nr of strings
device property: Fix reading pset strings using array access functions
device property: fwnode_property_read_string_array() may return -EILSEQ
ACPI / DSD: Document references, ports and endpoints
device property: Add fwnode_get_next_parent()
device property: Add support for fwnode endpoints
device property: Make dev_fwnode() public
of: Add of_fwnode_handle() to convert device nodes to fwnode_handle
device property: Add fwnode_handle_get()
device property: Add support for remote endpoints
ACPI / property: Add support for remote endpoints
device property: Add fwnode_get_named_child_node()
ACPI / property: Add fwnode_get_next_child_node()
device property: Add fwnode_get_parent()
ACPI / property: Add possiblity to retrieve parent firmware node
|
