| Age | Commit message (Collapse) | Author |
|---|
|
While all userspace tried to limit commandstreams to 64K in size,
a bug in the Mesa driver lead to command streams of up to 128K
being submitted. Allow those to avoid breaking existing userspace.
Fixes: 6dfa2fab8ddd ("drm/etnaviv: limit submit sizes")
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
This patch adds the necessary memory barriers.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver. Typical log messages are:
[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success
Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.
In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default. Users will be able to override this entry by means
of a module parameter, if they want.
CC: <stable@vger.kernel.org>
Reported-by: DocMAX <mail@vacharakis.de>
Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V causing VSAFE0V to be triggered. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED state where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid VSAFE0V events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: 28b43d3d746b8 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Missed adding the Icelake-D CPU to the list. It uses the same MSRs
to control and read the inventory number as all the other models.
Fixes: dc6b025de95b ("x86/mce: Add Xeon Icelake to list of CPUs that support PPIN")
Reported-by: Ailin Xu <ailin.xu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220121174743.1875294-2-tony.luck@intel.com
|
|
This fixes NULL pointer dereference that happens if
component master is registered with empty component match
list.
Fixes: 730b49aac426 ("usb: typec: port-mapper: Convert to the component framework")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220124090228.41396-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code that creates the links to the USB ports attached to
a connector inside the system assumed that the ACPI nodes
(fwnodes) always exist for the connectors, but it can not do
that.
There is no guarantee that every USB Type-C connector has
ACPI device node representing it in the ACPI tables, and
even if there are the nodes in the ACPI tables, the _STA
method in those nodes may still return 0 (which means the
device does not exist from ACPI PoW).
This fixes NULL pointer dereference that happens if the
nodes are missing.
Fixes: 730b49aac426 ("usb: typec: port-mapper: Convert to the component framework")
Reported-and-tested-by: Robert Święcki <robert@swiecki.net>
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220124090228.41396-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the AMS and Collision Avoidance, tcpm often needs to change the CC's
termination. When one CC line is sourcing Vconn, if we still change its
termination, the voltage of the another CC line is likely to be fluctuant
and unstable.
Therefore, we should verify whether a CC line is sourcing Vconn before
changing its termination and only change the termination that is not
a Vconn line. This can be done by reading the Vconn Present bit of
POWER_ STATUS register. To determine the polarity, we can read the
Plug Orientation bit of TCPC_CONTROL register. Since Vconn can only be
sourced if Plug Orientation is set.
Fixes: 0908c5aca31e ("usb: typec: tcpm: AMS and Collision Avoidance")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20220113092943.752372-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is an unused wrapper forcing kmalloc allocation for registering
nosave regions. Also, rename __register_nosave_region() to
register_nosave_region() now that there is no need for disambiguation.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
when CONFIG_USB_ROLE_SWITCH is not defined,
add usb_role_switch_find_by_fwnode() definition which return NULL.
Fixes: c6919d5e0cd1 ("usb: roles: Add usb_role_switch_find_by_fwnode()")
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1641818608-25039-1-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The buffer handling in pm_show_wakelocks() is tricky, and hopefully
correct. Ensure it really is correct by using sysfs_emit_at() which
handles all of the tricky string handling logic in a PAGE_SIZE buffer
for us automatically as this is a sysfs file being read from.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Copy scattered mac address octets into an array then eth_hw_addr_set().
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20220125144007.64407-1-tsbogend@alpha.franken.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With system suspend using pm_runtime_force_suspend() we can't rely on
the pm_runtime_get_if_in_use() trick to deal with devfreq callbacks
after (or racing with) suspend. So flush any pending idle or boost
work in the suspend path.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220108180913.814448-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
System suspend uses pm_runtime_force_suspend(), which cheekily bypasses
the runpm reference counts. This doesn't actually work so well when the
GPU is active. So add a reasonable delay waiting for the GPU to become
idle.
Alternatively we could just return -EBUSY in this case, but that has the
disadvantage of causing system suspend to fail.
v2: s/ret/remaining [sboyd], and switch to using active_submits count
to ensure we aren't racing with submit cleanup (and devfreq idle
work getting scheduled, etc)
v3: fix inverted logic
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220108180913.814448-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Several fixes for defragmentation that got broken in 5.16 after
refactoring and added subpage support. The observed bugs are excessive
IO or uninterruptible ioctl.
All stable material"
* tag 'for-5.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: update writeback index when starting defrag
btrfs: add back missing dirty page rate limiting to defrag
btrfs: fix deadlock when reserving space during defrag
btrfs: defrag: properly update range->start for autodefrag
btrfs: defrag: fix wrong number of defragged sectors
btrfs: allow defrag to be interruptible
btrfs: fix too long loop when defragging a 1 byte file
|
|
Make kvm_vcpu_reload_apic_access_page() static
as it is no longer invoked directly by vmx
and it is also no longer exported.
No functional change intended.
Signed-off-by: Quanfa Fu <quanfafu@gmail.com>
Message-Id: <20211219091446.174584-1-quanfafu@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This selftest was accidentally removed by commit 6a58150859fd
("selftest: KVM: Add intra host migration tests"). Add it back.
Fixes: 6a58150859fd ("selftest: KVM: Add intra host migration tests")
Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20220120003826.2805036-1-dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Set vmcs.GUEST_PENDING_DBG_EXCEPTIONS.BS, a.k.a. the pending single-step
breakpoint flag, when re-injecting a #DB with RFLAGS.TF=1, and STI or
MOVSS blocking is active. Setting the flag is necessary to make VM-Entry
consistency checks happy, as VMX has an invariant that if RFLAGS.TF is
set and STI/MOVSS blocking is true, then the previous instruction must
have been STI or MOV/POP, and therefore a single-step #DB must be pending
since the RFLAGS.TF cannot have been set by the previous instruction,
i.e. the one instruction delay after setting RFLAGS.TF must have already
expired.
Normally, the CPU sets vmcs.GUEST_PENDING_DBG_EXCEPTIONS.BS appropriately
when recording guest state as part of a VM-Exit, but #DB VM-Exits
intentionally do not treat the #DB as "guest state" as interception of
the #DB effectively makes the #DB host-owned, thus KVM needs to manually
set PENDING_DBG.BS when forwarding/re-injecting the #DB to the guest.
Note, although this bug can be triggered by guest userspace, doing so
requires IOPL=3, and guest userspace running with IOPL=3 has full access
to all I/O ports (from the guest's perspective) and can crash/reboot the
guest any number of ways. IOPL=3 is required because STI blocking kicks
in if and only if RFLAGS.IF is toggled 0=>1, and if CPL>IOPL, STI either
takes a #GP or modifies RFLAGS.VIF, not RFLAGS.IF.
MOVSS blocking can be initiated by userspace, but can be coincident with
a #DB if and only if DR7.GD=1 (General Detect enabled) and a MOV DR is
executed in the MOVSS shadow. MOV DR #GPs at CPL>0, thus MOVSS blocking
is problematic only for CPL0 (and only if the guest is crazy enough to
access a DR in a MOVSS shadow). All other sources of #DBs are either
suppressed by MOVSS blocking (single-step, code fetch, data, and I/O),
are mutually exclusive with MOVSS blocking (T-bit task switch), or are
already handled by KVM (ICEBP, a.k.a. INT1).
This bug was originally found by running tests[1] created for XSA-308[2].
Note that Xen's userspace test emits ICEBP in the MOVSS shadow, which is
presumably why the Xen bug was deemed to be an exploitable DOS from guest
userspace. KVM already handles ICEBP by skipping the ICEBP instruction
and thus clears MOVSS blocking as a side effect of its "emulation".
[1] http://xenbits.xenproject.org/docs/xtf/xsa-308_2main_8c_source.html
[2] https://xenbits.xen.org/xsa/advisory-308.html
Reported-by: David Woodhouse <dwmw2@infradead.org>
Reported-by: Alexander Graf <graf@amazon.de>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220120000624.655815-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Full equality check of CPUID data on update (kvm_cpuid_check_equal()) may
fail for SGX enabled CPUs as CPUID.(EAX=0x12,ECX=1) is currently being
mangled in kvm_vcpu_after_set_cpuid(). Move it to
__kvm_update_cpuid_runtime() and split off cpuid_get_supported_xcr0()
helper as 'vcpu->arch.guest_supported_xcr0' update needs (logically)
to stay in kvm_vcpu_after_set_cpuid().
Cc: stable@vger.kernel.org
Fixes: feb627e8d6f6 ("KVM: x86: Forbid KVM_SET_CPUID{,2} after KVM_RUN")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220124103606.2630588-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Since some interrupt states may be cleared by hardware, the driver
may receive an empty interrupt. Currently, the VF driver directly
disables the vector0 interrupt in this case. As a result, the VF
is unavailable. Therefore, the vector0 interrupt should be enabled
in this case.
Fixes: b90fcc5bd904 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent changes made netdev->dev_addr const, and it's passed
directly to mpc52xx_fec_set_paddr().
Similar problem exists on the probe patch, the driver needs
to call eth_hw_addr_set().
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per VESA DisplayID Standard v2.0: Type VII Timing – Detailed Timing Data
Definitions were already provided as type I, but not used
Signed-off-by: Yaroslav Bolyukin <iam@lach.pw>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220123191955.57994-1-iam@lach.pw
|
|
The cpsw driver didn't properly initialise the struct page_pool_params
before calling page_pool_create(), which leads to crashes after the struct
has been expanded with new parameters.
The second Fixes tag below is where the buggy code was introduced, but
because the code was moved around this patch will only apply on top of the
commit in the first Fixes tag.
Fixes: c5013ac1dd0e ("net: ethernet: ti: cpsw: move set of common functions in cpsw_priv")
Fixes: 9ed4050c0d75 ("net: ethernet: ti: cpsw: add XDP support")
Reported-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ym needs to be free when ym->cmd != SIOCYAMSMCS.
Fixes: 0781168e23a2 ("yam: fix a missing-check bug")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, on EEE capable platforms, if EEE SW timer is used, the SW
timer cause 1 wakeup/s even if the TX has successfully entered EEE.
Remove this unnecessary wakeup by only calling mod_timer() if we
haven't successfully entered EEE.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support the YUV output, we'll need the atomic state to know
what is the state of the associated property in the CSC setup callback.
Let's change the prototype of that callback to allow us to access it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-11-maxime@cerno.tech
|
|
The current CSC setup code for the BCM2711 uses a sequence of register
writes to configure the CSC depending on whether we output using a full
or limited range.
However, with the upcoming introduction of the YUV output, we're going
to add new matrices to perform the conversions, so we should switch to
something a bit more flexible that takes the matrix as an argument and
programs the CSC accordingly.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-10-maxime@cerno.tech
|
|
On BCM2711, the HDMI_CSC_CTL register value has been hardcoded to an
opaque value. Let's replace it with properly defined values.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-9-maxime@cerno.tech
|
|
On the BCM2711, the HDMI_VEC_INTERFACE_XBAR register configuration
depends on whether we're using an RGB or YUV output. Let's move that
configuration to the CSC setup.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-8-maxime@cerno.tech
|
|
The CSC callbacks takes a boolean as an argument to tell whether we're
using the full range or limited range RGB.
However, with the upcoming YUV support, the logic will be a bit more
complex. In order to address this, let's make the callbacks take the
entire mode, and call our new helper to tell whether the full or limited
range RGB should be used.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-7-maxime@cerno.tech
|
|
We're going to need to tell whether we want to run with a full or
limited range RGB output in multiple places in the code, so let's create
a helper that will return whether we need with full range or not.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-6-maxime@cerno.tech
|
|
The HDMI specification mentions YCbCr everywhere, but our enums have
YCrCb. Let's rename it to match.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-5-maxime@cerno.tech
|
|
The current code assumes that the RGB444 and YUV444 formats are the
same, but the HDMI 2.0 specification states that:
The three DC_XXbit bits above only indicate support for RGB 4:4:4 at
that pixel size. Support for YCBCR 4:4:4 in Deep Color modes is
indicated with the DC_Y444 bit. If DC_Y444 is set, then YCBCR 4:4:4
is supported for all modes indicated by the DC_XXbit flags.
So if we have YUV444 support and any DC_XXbit flag set but the DC_Y444
flag isn't, we'll assume that we support that deep colour mode for
YUV444 which breaks the specification.
In order to fix this, let's split the edid_hdmi_dc_modes field in struct
drm_display_info into two fields, one for RGB444 and one for YUV444.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d0c94692e0a3 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-4-maxime@cerno.tech
|
|
The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This is also broken with YUV444 if it's supported by the display, but
DRM_EDID_HDMI_DC_Y444 isn't set. In such a case, the code will clear
color_formats of the YUV444 support set previously in
drm_parse_cea_ext(), but will not set it back.
Since the formats supported are already setup properly in
drm_parse_cea_ext(), let's just remove the code modifying the formats in
drm_parse_hdmi_deep_color_info()
Fixes: d0c94692e0a3 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-3-maxime@cerno.tech
|
|
The drm_hdmi_avi_infoframe_colorspace() function actually sets the
colorimetry and extended_colorimetry fields in the hdmi_avi_infoframe
structure with DRM_MODE_COLORIMETRY_* values.
To make things worse, the hdmi_avi_infoframe structure also has a
colorspace field used to signal whether an RGB or YUV output is being
used.
Let's remove the inconsistency and allow for the colorspace usage by
renaming the function.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-2-maxime@cerno.tech
|
|
Also add notes that for atomic drivers it's really somewhere else and
no longer in struct drm_crtc.
Maybe we should put a bigger warning here that this is confusing,
since the pixel format is a plane property, but the GAMMA_LUT property
is on the crtc. But I think we can fix this if/when someone finds a
need for a per-plane CLUT, since I'm not sure such hw even exists. I'm
also not sure whether even hardware with a CLUT and a full color
correction pipeline with degamm/cgm/gamma exists.
Motivated by comments from Geert that we have a gap here.
v2: More names for color luts (Laurent).
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124221633.952374-1-daniel.vetter@ffwll.ch
|
|
Pull ARM fixes from Russell King:
- Fix panic whe both KASAN and KPROBEs are enabled
- Avoid alignment faults in copy_*_kernel_nofault()
- Align SMP alternatives in modules
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9180/1: Thumb2: align ALT_UP() sections in modules sufficiently
ARM: 9179/1: uaccess: avoid alignment faults in copy_[from|to]_kernel_nofault
ARM: 9170/1: fix panic when kasan and kprobe are enabled
|
|
The decrementer exception can fail to be cleared when the interrupt
returns in the case where the decrementer wraps with the next timer
still beyond decrementer_max. This results in a decrementer interrupt
storm. This is triggerable with small decrementer system with hard
and soft watchdogs disabled.
Fix this by always programming the decrementer if there was no timer.
Fixes: 0faf20a1ad16 ("powerpc/64s/interrupt: Don't enable MSR[EE] in irq handlers unless perf is in use")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220124143930.3923442-1-npiggin@gmail.com
|
|
The L0 is storing HFSCR requested by the L1 for the L2 in struct
kvm_nested_guest when the L1 requests a vCPU enter L2. kvm_nested_guest
is not a per-vCPU structure. Hilarity ensues.
Fix it by moving the nested hfscr into the vCPU structure together with
the other per-vCPU nested fields.
Fixes: 8b210a880b35 ("KVM: PPC: Book3S HV Nested: Make nested HFSCR state accessible")
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220122105530.3477250-1-npiggin@gmail.com
|
|
In case of a modeset where a mode gets split across multiple CRTCs
in the driver specific implementation (bigjoiner in i915) we wrongly count
the affected CRTCs based on the drm_crtc_mask and indicate the stolen CRTC as
an affected CRTC in atomic_check_only().
This triggers a warning since affected CRTCs doent match requested CRTC.
To fix this in such bigjoiner configurations, we should only
increment affected crtcs if that CRTC is enabled in UAPI not
if it is just used internally in the driver to split the mode.
v3: Add the same uapi crtc_state->enable check in requested
crtc calc (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Simon Ser <contact@emersion.fr>
Cc: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.11+
Fixes: 919c2299a893 ("drm/i915: Enable bigjoiner")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211004115913.23889-1-manasi.d.navare@intel.com
|
|
In myrs_detect(), cs->disable_intr is NULL when privdata->hw_init() fails
with non-zero. In this case, myrs_cleanup(cs) will call a NULL ptr and
crash the kernel.
[ 1.105606] myrs 0000:00:03.0: Unknown Initialization Error 5A
[ 1.105872] myrs 0000:00:03.0: Failed to initialize Controller
[ 1.106082] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 1.110774] Call Trace:
[ 1.110950] myrs_cleanup+0xe4/0x150 [myrs]
[ 1.111135] myrs_probe.cold+0x91/0x56a [myrs]
[ 1.111302] ? DAC960_GEM_intr_handler+0x1f0/0x1f0 [myrs]
[ 1.111500] local_pci_probe+0x48/0x90
Link: https://lore.kernel.org/r/20220123225717.1069538-1-ztong0001@gmail.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pointer SCp is being re-assigned the same value that it was initialized to
a few lines earlier, the assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20220123175530.110462-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This event is raised when link is lost as specified in UFSHCI spec and that
means communication is not possible. Thus initializing UFS interface needs
to be done.
Make UFS driver considers Link Lost as fatal in the INT_FATAL_ERRORS
mask. This will trigger a host reset whenever a link lost interrupt occurs.
Link: https://lore.kernel.org/r/1642743475-54275-1-git-send-email-kwmad.kim@samsung.com
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The return value of ufshcd_set_dev_pwr_mode() is passed to device PM
core. However, the function currently returns a SCSI result which the PM
core doesn't understand. This might lead to unexpected behaviors in
userland; a platform reset was observed in Android.
Use a generic error code for SSU failures.
Link: https://lore.kernel.org/r/1642743182-54098-1-git-send-email-kwmad.kim@samsung.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL. So, if it fails, the 32-bit case will also fail
for the same reason.
Simplify code and remove some dead code accordingly.
[1]: https://lore.kernel.org/linux-kernel/YL3vSPK5DXTNvgdx@infradead.org/#t
Link: https://lore.kernel.org/r/5663cef9b54004fa56cca7ce65f51eadfc3ecddb.1642238127.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL. So, if it fails, the 32-bit case will also fail
for the same reason.
Simplify code and remove some dead code accordingly.
[1]: https://lore.kernel.org/linux-kernel/YL3vSPK5DXTNvgdx@infradead.org/#t
Link: https://lore.kernel.org/r/1bf2d3660178b0e6f172e5208bc0bd68d31d9268.1642237482.git.christophe.jaillet@wanadoo.fr
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL. So, if it fails, the 32-bit case will also fail
for the same reason.
Simplify code and remove some dead code accordingly.
[1]: https://lore.kernel.org/linux-kernel/YL3vSPK5DXTNvgdx@infradead.org/#t
Link: https://lore.kernel.org/r/dbbe8671ca760972d80f8d35f3170b4609bee368.1642236763.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The bnx2fc_destroy() functions are removing the interface before calling
destroy_work. This results multiple WARNings from sysfs_remove_group() as
the controller rport device attributes are removed too early.
Replace the fcoe_port's destroy_work queue. It's not needed.
The problem is easily reproducible with the following steps.
Example:
$ dmesg -w &
$ systemctl enable --now fcoe
$ fipvlan -s -c ens2f1
$ fcoeadm -d ens2f1.802
[ 583.464488] host2: libfc: Link down on port (7500a1)
[ 583.472651] bnx2fc: 7500a1 - rport not created Yet!!
[ 583.490468] ------------[ cut here ]------------
[ 583.538725] sysfs group 'power' not found for kobject 'rport-2:0-0'
[ 583.568814] WARNING: CPU: 3 PID: 192 at fs/sysfs/group.c:279 sysfs_remove_group+0x6f/0x80
[ 583.607130] Modules linked in: dm_service_time 8021q garp mrp stp llc bnx2fc cnic uio rpcsec_gss_krb5 auth_rpcgss nfsv4 ...
[ 583.942994] CPU: 3 PID: 192 Comm: kworker/3:2 Kdump: loaded Not tainted 5.14.0-39.el9.x86_64 #1
[ 583.984105] Hardware name: HP ProLiant DL120 G7, BIOS J01 07/01/2013
[ 584.016535] Workqueue: fc_wq_2 fc_rport_final_delete [scsi_transport_fc]
[ 584.050691] RIP: 0010:sysfs_remove_group+0x6f/0x80
[ 584.074725] Code: ff 5b 48 89 ef 5d 41 5c e9 ee c0 ff ff 48 89 ef e8 f6 b8 ff ff eb d1 49 8b 14 24 48 8b 33 48 c7 c7 ...
[ 584.162586] RSP: 0018:ffffb567c15afdc0 EFLAGS: 00010282
[ 584.188225] RAX: 0000000000000000 RBX: ffffffff8eec4220 RCX: 0000000000000000
[ 584.221053] RDX: ffff8c1586ce84c0 RSI: ffff8c1586cd7cc0 RDI: ffff8c1586cd7cc0
[ 584.255089] RBP: 0000000000000000 R08: 0000000000000000 R09: ffffb567c15afc00
[ 584.287954] R10: ffffb567c15afbf8 R11: ffffffff8fbe7f28 R12: ffff8c1486326400
[ 584.322356] R13: ffff8c1486326480 R14: ffff8c1483a4a000 R15: 0000000000000004
[ 584.355379] FS: 0000000000000000(0000) GS:ffff8c1586cc0000(0000) knlGS:0000000000000000
[ 584.394419] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 584.421123] CR2: 00007fe95a6f7840 CR3: 0000000107674002 CR4: 00000000000606e0
[ 584.454888] Call Trace:
[ 584.466108] device_del+0xb2/0x3e0
[ 584.481701] device_unregister+0x13/0x60
[ 584.501306] bsg_unregister_queue+0x5b/0x80
[ 584.522029] bsg_remove_queue+0x1c/0x40
[ 584.541884] fc_rport_final_delete+0xf3/0x1d0 [scsi_transport_fc]
[ 584.573823] process_one_work+0x1e3/0x3b0
[ 584.592396] worker_thread+0x50/0x3b0
[ 584.609256] ? rescuer_thread+0x370/0x370
[ 584.628877] kthread+0x149/0x170
[ 584.643673] ? set_kthread_struct+0x40/0x40
[ 584.662909] ret_from_fork+0x22/0x30
[ 584.680002] ---[ end trace 53575ecefa942ece ]---
Link: https://lore.kernel.org/r/20220115040044.1013475-1-jmeneghi@redhat.com
Fixes: 0cbf32e1681d ("[SCSI] bnx2fc: Avoid calling bnx2fc_if_destroy with unnecessary locks")
Tested-by: Guangwu Zhang <guazhang@redhat.com>
Co-developed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Suppose we have an environment with a number of non-NPIV FCP devices
(virtual HBAs / FCP devices / zfcp "adapter"s) sharing the same physical
FCP channel (HBA port) and its I_T nexus. Plus a number of storage target
ports zoned to such shared channel. Now one target port logs out of the
fabric causing an RSCN. Zfcp reacts with an ADISC ELS and subsequent port
recovery depending on the ADISC result. This happens on all such FCP
devices (in different Linux images) concurrently as they all receive a copy
of this RSCN. In the following we look at one of those FCP devices.
Requests other than FSF_QTCB_FCP_CMND can be slow until they get a
response.
Depending on which requests are affected by slow responses, there are
different recovery outcomes. Here we want to fix failed recoveries on port
or adapter level by avoiding recovery requests that can be slow.
We need the cached N_Port_ID for the remote port "link" test with ADISC.
Just before sending the ADISC, we now intentionally forget the old cached
N_Port_ID. The idea is that on receiving an RSCN for a port, we have to
assume that any cached information about this port is stale. This forces a
fresh new GID_PN [FC-GS] nameserver lookup on any subsequent recovery for
the same port. Since we typically can still communicate with the nameserver
efficiently, we now reach steady state quicker: Either the nameserver still
does not know about the port so we stop recovery, or the nameserver already
knows the port potentially with a new N_Port_ID and we can successfully and
quickly perform open port recovery. For the one case, where ADISC returns
successfully, we re-initialize port->d_id because that case does not
involve any port recovery.
This also solves a problem if the storage WWPN quickly logs into the fabric
again but with a different N_Port_ID. Such as on virtual WWPN takeover
during target NPIV failover.
[https://www.redbooks.ibm.com/abstracts/redp5477.html] In that case the
RSCN from the storage FDISC was ignored by zfcp and we could not
successfully recover the failover. On some later failback on the storage,
we could have been lucky if the virtual WWPN got the same old N_Port_ID
from the SAN switch as we still had cached. Then the related RSCN
triggered a successful port reopen recovery. However, there is no
guarantee to get the same N_Port_ID on NPIV FDISC.
Even though NPIV-enabled FCP devices are not affected by this problem, this
code change optimizes recovery time for gone remote ports as a side effect.
The timely drop of cached N_Port_IDs prevents unnecessary slow open port
attempts.
While the problem might have been in code before v2.6.32 commit
799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") this fix
depends on the gid_pn_work introduced with that commit, so we mark it as
culprit to satisfy fix dependencies.
Note: Point-to-point remote port is already handled separately and gets its
N_Port_ID from the cached peer_d_id. So resetting port->d_id in general
does not affect PtP.
Link: https://lore.kernel.org/r/20220118165803.3667947-1-maier@linux.ibm.com
Fixes: 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp")
Cc: <stable@vger.kernel.org> #2.6.32+
Suggested-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
