| Age | Commit message (Collapse) | Author |
|---|
|
DP83848 datasheet (section 4.7.2) indicates that the reset pin should be
toggled after the clocks are running. Add the PHY_RST_AFTER_CLK_EN to
make sure that this indication is respected.
In my experience not having this flag enabled would lead to, on some
boots, the wrong MII mode being selected if the PHY was initialized on
the bootloader and was receiving data during Linux boot.
Signed-off-by: Diogo Silva <diogompaissilva@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 34e45ad9378c ("net: phy: dp83848: Add TI DP83848 Ethernet PHY")
Link: https://patch.msgid.link/20241102151504.811306-1-paissilva@ld-100007.ds1.internal
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mmap_region() function is somewhat terrifying, with spaghetti-like
control flow and numerous means by which issues can arise and incomplete
state, memory leaks and other unpleasantness can occur.
A large amount of the complexity arises from trying to handle errors late
in the process of mapping a VMA, which forms the basis of recently
observed issues with resource leaks and observable inconsistent state.
Taking advantage of previous patches in this series we move a number of
checks earlier in the code, simplifying things by moving the core of the
logic into a static internal function __mmap_region().
Doing this allows us to perform a number of checks up front before we do
any real work, and allows us to unwind the writable unmap check
unconditionally as required and to perform a CONFIG_DEBUG_VM_MAPLE_TREE
validation unconditionally also.
We move a number of things here:
1. We preallocate memory for the iterator before we call the file-backed
memory hook, allowing us to exit early and avoid having to perform
complicated and error-prone close/free logic. We carefully free
iterator state on both success and error paths.
2. The enclosing mmap_region() function handles the mapping_map_writable()
logic early. Previously the logic had the mapping_map_writable() at the
point of mapping a newly allocated file-backed VMA, and a matching
mapping_unmap_writable() on success and error paths.
We now do this unconditionally if this is a file-backed, shared writable
mapping. If a driver changes the flags to eliminate VM_MAYWRITE, however
doing so does not invalidate the seal check we just performed, and we in
any case always decrement the counter in the wrapper.
We perform a debug assert to ensure a driver does not attempt to do the
opposite.
3. We also move arch_validate_flags() up into the mmap_region()
function. This is only relevant on arm64 and sparc64, and the check is
only meaningful for SPARC with ADI enabled. We explicitly add a warning
for this arch if a driver invalidates this check, though the code ought
eventually to be fixed to eliminate the need for this.
With all of these measures in place, we no longer need to explicitly close
the VMA on error paths, as we place all checks which might fail prior to a
call to any driver mmap hook.
This eliminates an entire class of errors, makes the code easier to reason
about and more robust.
Link: https://lkml.kernel.org/r/6e0becb36d2f5472053ac5d544c0edfe9b899e25.1730224667.git.lorenzo.stoakes@oracle.com
Fixes: deb0f6562884 ("mm/mmap: undo ->mmap() when arch_validate_flags() fails")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Mark Brown <broonie@kernel.org>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Currently MTE is permitted in two circumstances (desiring to use MTE
having been specified by the VM_MTE flag) - where MAP_ANONYMOUS is
specified, as checked by arch_calc_vm_flag_bits() and actualised by
setting the VM_MTE_ALLOWED flag, or if the file backing the mapping is
shmem, in which case we set VM_MTE_ALLOWED in shmem_mmap() when the mmap
hook is activated in mmap_region().
The function that checks that, if VM_MTE is set, VM_MTE_ALLOWED is also
set is the arm64 implementation of arch_validate_flags().
Unfortunately, we intend to refactor mmap_region() to perform this check
earlier, meaning that in the case of a shmem backing we will not have
invoked shmem_mmap() yet, causing the mapping to fail spuriously.
It is inappropriate to set this architecture-specific flag in general mm
code anyway, so a sensible resolution of this issue is to instead move the
check somewhere else.
We resolve this by setting VM_MTE_ALLOWED much earlier in do_mmap(), via
the arch_calc_vm_flag_bits() call.
This is an appropriate place to do this as we already check for the
MAP_ANONYMOUS case here, and the shmem file case is simply a variant of
the same idea - we permit RAM-backed memory.
This requires a modification to the arch_calc_vm_flag_bits() signature to
pass in a pointer to the struct file associated with the mapping, however
this is not too egregious as this is only used by two architectures anyway
- arm64 and parisc.
So this patch performs this adjustment and removes the unnecessary
assignment of VM_MTE_ALLOWED in shmem_mmap().
[akpm@linux-foundation.org: fix whitespace, per Catalin]
Link: https://lkml.kernel.org/r/ec251b20ba1964fb64cf1607d2ad80c47f3873df.1730224667.git.lorenzo.stoakes@oracle.com
Fixes: deb0f6562884 ("mm/mmap: undo ->mmap() when arch_validate_flags() fails")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Refactor the map_deny_write_exec() to not unnecessarily require a VMA
parameter but rather to accept VMA flags parameters, which allows us to
use this function early in mmap_region() in a subsequent commit.
While we're here, we refactor the function to be more readable and add
some additional documentation.
Link: https://lkml.kernel.org/r/6be8bb59cd7c68006ebb006eb9d8dc27104b1f70.1730224667.git.lorenzo.stoakes@oracle.com
Fixes: deb0f6562884 ("mm/mmap: undo ->mmap() when arch_validate_flags() fails")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Jann Horn <jannh@google.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Incorrect invocation of VMA callbacks when the VMA is no longer in a
consistent state is bug prone and risky to perform.
With regards to the important vm_ops->close() callback We have gone to
great lengths to try to track whether or not we ought to close VMAs.
Rather than doing so and risking making a mistake somewhere, instead
unconditionally close and reset vma->vm_ops to an empty dummy operations
set with a NULL .close operator.
We introduce a new function to do so - vma_close() - and simplify existing
vms logic which tracked whether we needed to close or not.
This simplifies the logic, avoids incorrect double-calling of the .close()
callback and allows us to update error paths to simply call vma_close()
unconditionally - making VMA closure idempotent.
Link: https://lkml.kernel.org/r/28e89dda96f68c505cb6f8e9fc9b57c3e9f74b42.1730224667.git.lorenzo.stoakes@oracle.com
Fixes: deb0f6562884 ("mm/mmap: undo ->mmap() when arch_validate_flags() fails")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reviewed-by: Jann Horn <jannh@google.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "fix error handling in mmap_region() and refactor
(hotfixes)", v4.
mmap_region() is somewhat terrifying, with spaghetti-like control flow and
numerous means by which issues can arise and incomplete state, memory
leaks and other unpleasantness can occur.
A large amount of the complexity arises from trying to handle errors late
in the process of mapping a VMA, which forms the basis of recently
observed issues with resource leaks and observable inconsistent state.
This series goes to great lengths to simplify how mmap_region() works and
to avoid unwinding errors late on in the process of setting up the VMA for
the new mapping, and equally avoids such operations occurring while the
VMA is in an inconsistent state.
The patches in this series comprise the minimal changes required to
resolve existing issues in mmap_region() error handling, in order that
they can be hotfixed and backported. There is additionally a follow up
series which goes further, separated out from the v1 series and sent and
updated separately.
This patch (of 5):
After an attempted mmap() fails, we are no longer in a situation where we
can safely interact with VMA hooks. This is currently not enforced,
meaning that we need complicated handling to ensure we do not incorrectly
call these hooks.
We can avoid the whole issue by treating the VMA as suspect the moment
that the file->f_ops->mmap() function reports an error by replacing
whatever VMA operations were installed with a dummy empty set of VMA
operations.
We do so through a new helper function internal to mm - mmap_file() -
which is both more logically named than the existing call_mmap() function
and correctly isolates handling of the vm_op reassignment to mm.
All the existing invocations of call_mmap() outside of mm are ultimately
nested within the call_mmap() from mm, which we now replace.
It is therefore safe to leave call_mmap() in place as a convenience
function (and to avoid churn). The invokers are:
ovl_file_operations -> mmap -> ovl_mmap() -> backing_file_mmap()
coda_file_operations -> mmap -> coda_file_mmap()
shm_file_operations -> shm_mmap()
shm_file_operations_huge -> shm_mmap()
dma_buf_fops -> dma_buf_mmap_internal -> i915_dmabuf_ops
-> i915_gem_dmabuf_mmap()
None of these callers interact with vm_ops or mappings in a problematic
way on error, quickly exiting out.
Link: https://lkml.kernel.org/r/cover.1730224667.git.lorenzo.stoakes@oracle.com
Link: https://lkml.kernel.org/r/d41fd763496fd0048a962f3fd9407dc72dd4fd86.1730224667.git.lorenzo.stoakes@oracle.com
Fixes: deb0f6562884 ("mm/mmap: undo ->mmap() when arch_validate_flags() fails")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Jann Horn <jannh@google.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Recent changes are putting more pressure on THP deferred split queues:
under load revealing long-standing races, causing list_del corruptions,
"Bad page state"s and worse (I keep BUGs in both of those, so usually
don't get to see how badly they end up without). The relevant recent
changes being 6.8's mTHP, 6.10's mTHP swapout, and 6.12's mTHP swapin,
improved swap allocation, and underused THP splitting.
Before fixing locking: rename misleading folio_undo_large_rmappable(),
which does not undo large_rmappable, to folio_unqueue_deferred_split(),
which is what it does. But that and its out-of-line __callee are mm
internals of very limited usability: add comment and WARN_ON_ONCEs to
check usage; and return a bool to say if a deferred split was unqueued,
which can then be used in WARN_ON_ONCEs around safety checks (sparing
callers the arcane conditionals in __folio_unqueue_deferred_split()).
Just omit the folio_unqueue_deferred_split() from free_unref_folios(), all
of whose callers now call it beforehand (and if any forget then bad_page()
will tell) - except for its caller put_pages_list(), which itself no
longer has any callers (and will be deleted separately).
Swapout: mem_cgroup_swapout() has been resetting folio->memcg_data 0
without checking and unqueueing a THP folio from deferred split list;
which is unfortunate, since the split_queue_lock depends on the memcg
(when memcg is enabled); so swapout has been unqueueing such THPs later,
when freeing the folio, using the pgdat's lock instead: potentially
corrupting the memcg's list. __remove_mapping() has frozen refcount to 0
here, so no problem with calling folio_unqueue_deferred_split() before
resetting memcg_data.
That goes back to 5.4 commit 87eaceb3faa5 ("mm: thp: make deferred split
shrinker memcg aware"): which included a check on swapcache before adding
to deferred queue, but no check on deferred queue before adding THP to
swapcache. That worked fine with the usual sequence of events in reclaim
(though there were a couple of rare ways in which a THP on deferred queue
could have been swapped out), but 6.12 commit dafff3f4c850 ("mm: split
underused THPs") avoids splitting underused THPs in reclaim, which makes
swapcache THPs on deferred queue commonplace.
Keep the check on swapcache before adding to deferred queue? Yes: it is
no longer essential, but preserves the existing behaviour, and is likely
to be a worthwhile optimization (vmstat showed much more traffic on the
queue under swapping load if the check was removed); update its comment.
Memcg-v1 move (deprecated): mem_cgroup_move_account() has been changing
folio->memcg_data without checking and unqueueing a THP folio from the
deferred list, sometimes corrupting "from" memcg's list, like swapout.
Refcount is non-zero here, so folio_unqueue_deferred_split() can only be
used in a WARN_ON_ONCE to validate the fix, which must be done earlier:
mem_cgroup_move_charge_pte_range() first try to split the THP (splitting
of course unqueues), or skip it if that fails. Not ideal, but moving
charge has been requested, and khugepaged should repair the THP later:
nobody wants new custom unqueueing code just for this deprecated case.
The 87eaceb3faa5 commit did have the code to move from one deferred list
to another (but was not conscious of its unsafety while refcount non-0);
but that was removed by 5.6 commit fac0516b5534 ("mm: thp: don't need care
deferred split queue in memcg charge move path"), which argued that the
existence of a PMD mapping guarantees that the THP cannot be on a deferred
list. As above, false in rare cases, and now commonly false.
Backport to 6.11 should be straightforward. Earlier backports must take
care that other _deferred_list fixes and dependencies are included. There
is not a strong case for backports, but they can fix cornercases.
Link: https://lkml.kernel.org/r/8dc111ae-f6db-2da7-b25c-7a20b1effe3b@google.com
Fixes: 87eaceb3faa5 ("mm: thp: make deferred split shrinker memcg aware")
Fixes: dafff3f4c850 ("mm: split underused THPs")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Chris Li <chrisl@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: Usama Arif <usamaarif642@gmail.com>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Recent changes are putting more pressure on THP deferred split queues:
under load revealing long-standing races, causing list_del corruptions,
"Bad page state"s and worse (I keep BUGs in both of those, so usually
don't get to see how badly they end up without). The relevant recent
changes being 6.8's mTHP, 6.10's mTHP swapout, and 6.12's mTHP swapin,
improved swap allocation, and underused THP splitting.
The new unlocked list_del_init() in deferred_split_scan() is buggy. I
gave bad advice, it looks plausible since that's a local on-stack list,
but the fact is that it can race with a third party freeing or migrating
the preceding folio (properly unqueueing it with refcount 0 while holding
split_queue_lock), thereby corrupting the list linkage.
The obvious answer would be to take split_queue_lock there: but it has a
long history of contention, so I'm reluctant to add to that. Instead,
make sure that there is always one safe (raised refcount) folio before, by
delaying its folio_put(). (And of course I was wrong to suggest updating
split_queue_len without the lock: leave that until the splice.)
And remove two over-eager partially_mapped checks, restoring those tests
to how they were before: if uncharge_folio() or free_tail_page_prepare()
finds _deferred_list non-empty, it's in trouble whether or not that folio
is partially_mapped (and the flag was already cleared in the latter case).
Link: https://lkml.kernel.org/r/81e34a8b-113a-0701-740e-2135c97eb1d7@google.com
Fixes: dafff3f4c850 ("mm: split underused THPs")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Usama Arif <usamaarif642@gmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Acked-by: Zi Yan <ziy@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Chris Li <chrisl@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yang Shi <shy828301@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The exec queue timestamp is only really useful when it's being queried
through the fdinfo. There's no need to update it so often, on every
job_free. Tracing a simple app like vkcube running shows an update
rate of ~ 120Hz. In case of discrete, the BO is on vram, creating a lot
of pcie transactions.
The update on job_free() is used to cover a gap: if exec
queue is created and destroyed rapidly, before a new query, the
timestamp still needs to be accumulated and accounted for in the xef.
Initial implementation in commit 6109f24f87d7 ("drm/xe: Add helper to
accumulate exec queue runtime") couldn't do it on the exec_queue_fini
since the xef could be gone at that point. However since commit
ce8c161cbad4 ("drm/xe: Add ref counting for xe_file") the xef is
refcounted and the exec queue always holds a reference, making this safe
now.
Improve the fix in commit 2149ded63079 ("drm/xe: Fix use after free when
client stats are captured") by reducing the frequency in which the
update is needed.
Fixes: 2149ded63079 ("drm/xe: Fix use after free when client stats are captured")
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241104143815.2112272-3-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 83db047d9425d9a649f01573797558eff0f632e1)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
In unlikely event that we fail during sending the new VF GGTT
configuration to the GuC, we will free only the GGTT node data
struct but will miss to release the actual GGTT allocation.
This will later lead to list corruption, GGTT space leak and
finally risking crash when unloading the driver:
[ ] ... [drm] GT0: PF: Failed to provision VF1 with 1073741824 (1.00 GiB) GGTT (-EIO)
[ ] ... [drm] GT0: PF: VF1 provisioning remains at 0 (0 B) GGTT
[ ] list_add corruption. next->prev should be prev (ffff88813cfcd628), but was 0000000000000000. (next=ffff88813cfe2028).
[ ] RIP: 0010:__list_add_valid_or_report+0x6b/0xb0
[ ] Call Trace:
[ ] drm_mm_insert_node_in_range+0x2c0/0x4e0
[ ] xe_ggtt_node_insert+0x46/0x70 [xe]
[ ] pf_provision_vf_ggtt+0x7f5/0xa70 [xe]
[ ] xe_gt_sriov_pf_config_set_ggtt+0x5e/0x770 [xe]
[ ] ggtt_set+0x4b/0x70 [xe]
[ ] simple_attr_write_xsigned.constprop.0.isra.0+0xb0/0x110
[ ] ... [drm] GT0: PF: Failed to provision VF1 with 1073741824 (1.00 GiB) GGTT (-ENOSPC)
[ ] ... [drm] GT0: PF: VF1 provisioning remains at 0 (0 B) GGTT
[ ] Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b7b: 0000 [#1] PREEMPT SMP NOPTI
[ ] RIP: 0010:drm_mm_remove_node+0x1b7/0x390
[ ] Call Trace:
[ ] <TASK>
[ ] ? die_addr+0x2e/0x80
[ ] ? exc_general_protection+0x1a1/0x3e0
[ ] ? asm_exc_general_protection+0x22/0x30
[ ] ? drm_mm_remove_node+0x1b7/0x390
[ ] ggtt_node_remove+0xa5/0xf0 [xe]
[ ] xe_ggtt_node_remove+0x35/0x70 [xe]
[ ] xe_ttm_bo_destroy+0x123/0x220 [xe]
[ ] intel_user_framebuffer_destroy+0x44/0x70 [xe]
[ ] intel_plane_destroy_state+0x3b/0xc0 [xe]
[ ] drm_atomic_state_default_clear+0x1cd/0x2f0
[ ] intel_atomic_state_clear+0x9/0x20 [xe]
[ ] __drm_atomic_state_free+0x1d/0xb0
Fix that by using pf_release_ggtt() on the error path, which now
works regardless if the node has GGTT allocation or not.
Fixes: 34e804220f69 ("drm/xe: Make xe_ggtt_node struct independent")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241104144901.1903-1-michal.wajdeczko@intel.com
(cherry picked from commit 43b1dd2b550f0861ce80fbfffd5881b1b26272b1)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Upon failure all locks need to be dropped before returning to the user.
Fixes: 58480c1c912f ("drm/xe: Skip VMAs pin when requesting signal to the last XE_EXEC")
Cc: <stable@vger.kernel.org>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241105043524.4062774-3-matthew.brost@intel.com
(cherry picked from commit 7d1a4258e602ffdce529f56686925034c1b3b095)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
In a couple of places after an exec queue is looked up the exec IOCTL
returns on input errors without dropping the exec queue ref. Fix this
ensuring the exec queue ref is dropped on input error.
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241105043524.4062774-2-matthew.brost@intel.com
(cherry picked from commit 07064a200b40ac2195cb6b7b779897d9377e5e6f)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into clk-fixes
Pull Qualcomm clk driver fixes from Bjorn Andersson:
- Correct flags for X Elite USB MP GDSC and pcie pipediv2 clocks
- Fix alpha PLL post_div mask for the cases where width is not
specified
- Avoid hangs in the SM8350 video driver (venus) by setting HW_CTRL
trigger feature on the video clocks
* tag 'qcom-clk-fixes-for-6.12' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
clk: qcom: gcc-x1e80100: Fix USB MP SS1 PHY GDSC pwrsts flags
clk: qcom: gcc-x1e80100: Fix halt_check for pipediv2 clocks
clk: qcom: clk-alpha-pll: Fix pll post div mask when width is not set
clk: qcom: videocc-sm8350: use HW_CTRL_TRIGGER for vcodec GDSCs
|
|
kmem_buckets_create
Commit b035f5a6d852 ("mm: slab: reduce the kmalloc() minimum alignment
if DMA bouncing possible") reduced ARCH_KMALLOC_MINALIGN to 8 on arm64.
However, with KASAN_HW_TAGS enabled, arch_slab_minalign() becomes 16.
This causes kmalloc_caches[*][8] to be aliased to kmalloc_caches[*][16],
resulting in kmem_buckets_create() attempting to create a kmem_cache for
size 16 twice. This duplication triggers warnings on boot:
[ 2.325108] ------------[ cut here ]------------
[ 2.325135] kmem_cache of name 'memdup_user-16' already exists
[ 2.325783] WARNING: CPU: 0 PID: 1 at mm/slab_common.c:107 __kmem_cache_create_args+0xb8/0x3b0
[ 2.327957] Modules linked in:
[ 2.328550] CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.0-rc5mm-unstable-arm64+ #12
[ 2.328683] Hardware name: QEMU QEMU Virtual Machine, BIOS 2024.02-2 03/11/2024
[ 2.328790] pstate: 61000009 (nZCv daif -PAN -UAO -TCO +DIT -SSBS BTYPE=--)
[ 2.328911] pc : __kmem_cache_create_args+0xb8/0x3b0
[ 2.328930] lr : __kmem_cache_create_args+0xb8/0x3b0
[ 2.328942] sp : ffff800083d6fc50
[ 2.328961] x29: ffff800083d6fc50 x28: f2ff0000c1674410 x27: ffff8000820b0598
[ 2.329061] x26: 000000007fffffff x25: 0000000000000010 x24: 0000000000002000
[ 2.329101] x23: ffff800083d6fce8 x22: ffff8000832222e8 x21: ffff800083222388
[ 2.329118] x20: f2ff0000c1674410 x19: f5ff0000c16364c0 x18: ffff800083d80030
[ 2.329135] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
[ 2.329152] x14: 0000000000000000 x13: 0a73747369786520 x12: 79646165726c6120
[ 2.329169] x11: 656820747563205b x10: 2d2d2d2d2d2d2d2d x9 : 0000000000000000
[ 2.329194] x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000
[ 2.329210] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
[ 2.329226] x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000
[ 2.329291] Call trace:
[ 2.329407] __kmem_cache_create_args+0xb8/0x3b0
[ 2.329499] kmem_buckets_create+0xfc/0x320
[ 2.329526] init_user_buckets+0x34/0x78
[ 2.329540] do_one_initcall+0x64/0x3c8
[ 2.329550] kernel_init_freeable+0x26c/0x578
[ 2.329562] kernel_init+0x3c/0x258
[ 2.329574] ret_from_fork+0x10/0x20
[ 2.329698] ---[ end trace 0000000000000000 ]---
[ 2.403704] ------------[ cut here ]------------
[ 2.404716] kmem_cache of name 'msg_msg-16' already exists
[ 2.404801] WARNING: CPU: 2 PID: 1 at mm/slab_common.c:107 __kmem_cache_create_args+0xb8/0x3b0
[ 2.404842] Modules linked in:
[ 2.404971] CPU: 2 UID: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.12.0-rc5mm-unstable-arm64+ #12
[ 2.405026] Tainted: [W]=WARN
[ 2.405043] Hardware name: QEMU QEMU Virtual Machine, BIOS 2024.02-2 03/11/2024
[ 2.405057] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 2.405079] pc : __kmem_cache_create_args+0xb8/0x3b0
[ 2.405100] lr : __kmem_cache_create_args+0xb8/0x3b0
[ 2.405111] sp : ffff800083d6fc50
[ 2.405115] x29: ffff800083d6fc50 x28: fbff0000c1674410 x27: ffff8000820b0598
[ 2.405135] x26: 000000000000ffd0 x25: 0000000000000010 x24: 0000000000006000
[ 2.405153] x23: ffff800083d6fce8 x22: ffff8000832222e8 x21: ffff800083222388
[ 2.405169] x20: fbff0000c1674410 x19: fdff0000c163d6c0 x18: ffff800083d80030
[ 2.405185] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
[ 2.405201] x14: 0000000000000000 x13: 0a73747369786520 x12: 79646165726c6120
[ 2.405217] x11: 656820747563205b x10: 2d2d2d2d2d2d2d2d x9 : 0000000000000000
[ 2.405233] x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000
[ 2.405248] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
[ 2.405271] x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000
[ 2.405287] Call trace:
[ 2.405293] __kmem_cache_create_args+0xb8/0x3b0
[ 2.405305] kmem_buckets_create+0xfc/0x320
[ 2.405315] init_msg_buckets+0x34/0x78
[ 2.405326] do_one_initcall+0x64/0x3c8
[ 2.405337] kernel_init_freeable+0x26c/0x578
[ 2.405348] kernel_init+0x3c/0x258
[ 2.405360] ret_from_fork+0x10/0x20
[ 2.405370] ---[ end trace 0000000000000000 ]---
To address this, alias kmem_cache for sizes smaller than min alignment
to the aligned sized kmem_cache, as done with the default system kmalloc
bucket.
Fixes: b32801d1255b ("mm/slab: Introduce kmem_buckets_create() and family")
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@gmail.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
In case of error when requesting ctrl_chan DMA channel, ctrl_chan is not
null. So the release of the dma channel leads to the following issue:
[ 4.879000] st,stm32-spdifrx 500d0000.audio-controller:
dma_request_slave_channel error -19
[ 4.888975] Unable to handle kernel NULL pointer dereference
at virtual address 000000000000003d
[...]
[ 5.096577] Call trace:
[ 5.099099] dma_release_channel+0x24/0x100
[ 5.103235] stm32_spdifrx_remove+0x24/0x60 [snd_soc_stm32_spdifrx]
[ 5.109494] stm32_spdifrx_probe+0x320/0x4c4 [snd_soc_stm32_spdifrx]
To avoid this issue, release channel only if the pointer is valid.
Fixes: 794df9448edb ("ASoC: stm32: spdifrx: manage rebind issue")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://patch.msgid.link/20241105140242.527279-1-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Avoid a possible buffer overflow if size is larger than 4K.
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f5d873f5825b40d886d03bd2aede91d4cf002434)
Cc: stable@vger.kernel.org
|
|
Users should not be able to run these.
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7ba9395430f611cfc101b1c2687732baafa239d5)
Cc: stable@vger.kernel.org
|
|
Regular users shouldn't have read access.
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit c0cfd2e652553d607b910be47d0cc5a7f3a78641)
Cc: stable@vger.kernel.org
|
|
For DPX mode, the number of memory partitions supported should be less
than or equal to 2.
Fixes: 1589c82a1085 ("drm/amdgpu: Check memory ranges for valid xcp mode")
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 990c4f580742de7bb78fa57420ffd182fc3ab4cd)
Cc: stable@vger.kernel.org
|
|
Roger Quadros says:
====================
net: ethernet: ti: am65-cpsw: Fixes to multi queue RX feature
On J7 platforms, setting up multiple RX flows was failing
as the RX free descriptor ring 0 is shared among all flows
and we did not allocate enough elements in the RX free descriptor
ring 0 to accommodate for all RX flows. Patch 1 fixes this.
The second patch fixes a warning if there was any error in
am65_cpsw_nuss_init_rx_chns() and am65_cpsw_nuss_cleanup_rx_chns()
was called after that.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
====================
Link: https://patch.msgid.link/20241101-am65-cpsw-multi-rx-j7-fix-v3-0-338fdd6a55da@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
flow->irq is initialized to 0 which is a valid IRQ. Set it to -EINVAL
in error path of am65_cpsw_nuss_init_rx_chns() so we do not try
to free an unallocated IRQ in am65_cpsw_nuss_remove_rx_chns().
If user tried to change number of RX queues and am65_cpsw_nuss_init_rx_chns()
failed due to any reason, the warning will happen if user tries to change
the number of RX queues after the error condition.
root@am62xx-evm:~# ethtool -L eth0 rx 3
[ 40.385293] am65-cpsw-nuss 8000000.ethernet: set new flow-id-base 19
[ 40.393211] am65-cpsw-nuss 8000000.ethernet: Failed to init rx flow2
netlink error: Invalid argument
root@am62xx-evm:~# ethtool -L eth0 rx 2
[ 82.306427] ------------[ cut here ]------------
[ 82.311075] WARNING: CPU: 0 PID: 378 at kernel/irq/devres.c:144 devm_free_irq+0x84/0x90
[ 82.469770] Call trace:
[ 82.472208] devm_free_irq+0x84/0x90
[ 82.475777] am65_cpsw_nuss_remove_rx_chns+0x6c/0xac [ti_am65_cpsw_nuss]
[ 82.482487] am65_cpsw_nuss_update_tx_rx_chns+0x2c/0x9c [ti_am65_cpsw_nuss]
[ 82.489442] am65_cpsw_set_channels+0x30/0x4c [ti_am65_cpsw_nuss]
[ 82.495531] ethnl_set_channels+0x224/0x2dc
[ 82.499713] ethnl_default_set_doit+0xb8/0x1b8
[ 82.504149] genl_family_rcv_msg_doit+0xc0/0x124
[ 82.508757] genl_rcv_msg+0x1f0/0x284
[ 82.512409] netlink_rcv_skb+0x58/0x130
[ 82.516239] genl_rcv+0x38/0x50
[ 82.519374] netlink_unicast+0x1d0/0x2b0
[ 82.523289] netlink_sendmsg+0x180/0x3c4
[ 82.527205] __sys_sendto+0xe4/0x158
[ 82.530779] __arm64_sys_sendto+0x28/0x38
[ 82.534782] invoke_syscall+0x44/0x100
[ 82.538526] el0_svc_common.constprop.0+0xc0/0xe0
[ 82.543221] do_el0_svc+0x1c/0x28
[ 82.546528] el0_svc+0x28/0x98
[ 82.549578] el0t_64_sync_handler+0xc0/0xc4
[ 82.553752] el0t_64_sync+0x190/0x194
[ 82.557407] ---[ end trace 0000000000000000 ]---
Fixes: da70d184a8c3 ("net: ethernet: ti: am65-cpsw: Introduce multi queue Rx")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
On J7 platforms, setting up multiple RX flows was failing
as the RX free descriptor ring 0 is shared among all flows
and we did not allocate enough elements in the RX free descriptor
ring 0 to accommodate for all RX flows.
This issue is not present on AM62 as separate pair of
rings are used for free and completion rings for each flow.
Fix this by allocating enough elements for RX free descriptor
ring 0.
However, we can no longer rely on desc_idx (descriptor based
offsets) to identify the pages in the respective flows as
free descriptor ring includes elements for all flows.
To solve this, introduce a new swdata data structure to store
flow_id and page. This can be used to identify which flow (page_pool)
and page the descriptor belonged to when popped out of the
RX rings.
Fixes: da70d184a8c3 ("net: ethernet: ti: am65-cpsw: Introduce multi queue Rx")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Rick reported that his Pluggable USB4 dock does not work anymore after
upgrading to v6.10 kernel.
It looks like commit c6ca1ac9f472 ("thunderbolt: Increase sideband
access polling delay") makes the device router enumeration happen later
than what might be expected by the dock (although there is no such limit
in the USB4 spec) which probably makes it assume there is something
wrong with the high-speed link and reset it. After the link is reset the
same issue happens again and again.
For this reason lower the sideband access delay from 5ms to 1ms. This
seems to work fine according to Rick's testing.
Reported-by: Rick Lahaye <rick@581238.xyz>
Closes: https://lore.kernel.org/linux-usb/000f01db247b$d10e1520$732a3f60$@581238.xyz/
Tested-by: Rick Lahaye <rick@581238.xyz>
Fixes: c6ca1ac9f472 ("thunderbolt: Increase sideband access polling delay")
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
If dev_get_regmap() fails, it returns NULL pointer not ERR_PTR(),
replace IS_ERR() with NULL pointer check, and return -ENODEV.
Fixes: d0f8e97866bf ("i2c: muxes: add support for tsd,mule-i2c multiplexer")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
ALSA SoC Sound has Generic Sound Card (Simple-Card, Audio-Graph-Card,
Audio-Graph-Card2). Adds its Maintainer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87ikt2a41c.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The "*cmd" variable can be controlled by the user via debugfs. That means
"new_cam" can be as high as 255 while the size of the uc->updated[] array
is UCSI_MAX_ALTMODES (30).
The call tree is:
ucsi_cmd() // val comes from simple_attr_write_xsigned()
-> ucsi_send_command()
-> ucsi_send_command_common()
-> ucsi_run_command() // calls ucsi->ops->sync_control()
-> ucsi_ccg_sync_control()
Fixes: 170a6726d0e2 ("usb: typec: ucsi: add support for separate DP altmode devices")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/325102b3-eaa8-4918-a947-22aca1146586@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the device was already runtime suspended then during system suspend
we cannot access the device registers else it will crash.
Also we cannot access any registers after dwc3_core_exit() on some
platforms so move the dwc3_enable_susphy() call to the top.
Cc: stable@vger.kernel.org # v5.15+
Reported-by: William McVicker <willmcvicker@google.com>
Closes: https://lore.kernel.org/all/ZyVfcUuPq56R2m1Y@google.com
Fixes: 705e3ce37bcc ("usb: dwc3: core: Fix system suspend on TI AM62 platforms")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241104-am62-lpm-usb-fix-v1-1-e93df73a4f0d@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the read of USB_PDPHY_RX_ACKNOWLEDGE_REG failed, then hdr_len and
txbuf_len are uninitialized. This commit stops to print uninitialized
value and misleading/false data.
Cc: stable@vger.kernel.org
Fixes: a4422ff22142 (" usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Signed-off-by: Rex Nie <rex.nie@jaguarmicro.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20241030133632.2116-1-rex.nie@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the driver is uninstalled and the VF is disabled concurrently, a
kernel crash occurs. The reason is that the two actions call function
pci_disable_sriov(). The num_VFs is checked to determine whether to
release the corresponding resources. During the second calling, num_VFs
is not 0 and the resource release function is called. However, the
corresponding resource has been released during the first invoking.
Therefore, the problem occurs:
[15277.839633][T50670] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
...
[15278.131557][T50670] Call trace:
[15278.134686][T50670] klist_put+0x28/0x12c
[15278.138682][T50670] klist_del+0x14/0x20
[15278.142592][T50670] device_del+0xbc/0x3c0
[15278.146676][T50670] pci_remove_bus_device+0x84/0x120
[15278.151714][T50670] pci_stop_and_remove_bus_device+0x6c/0x80
[15278.157447][T50670] pci_iov_remove_virtfn+0xb4/0x12c
[15278.162485][T50670] sriov_disable+0x50/0x11c
[15278.166829][T50670] pci_disable_sriov+0x24/0x30
[15278.171433][T50670] hnae3_unregister_ae_algo_prepare+0x60/0x90 [hnae3]
[15278.178039][T50670] hclge_exit+0x28/0xd0 [hclge]
[15278.182730][T50670] __se_sys_delete_module.isra.0+0x164/0x230
[15278.188550][T50670] __arm64_sys_delete_module+0x1c/0x30
[15278.193848][T50670] invoke_syscall+0x50/0x11c
[15278.198278][T50670] el0_svc_common.constprop.0+0x158/0x164
[15278.203837][T50670] do_el0_svc+0x34/0xcc
[15278.207834][T50670] el0_svc+0x20/0x30
For details, see the following figure.
rmmod hclge disable VFs
----------------------------------------------------
hclge_exit() sriov_numvfs_store()
... device_lock()
pci_disable_sriov() hns3_pci_sriov_configure()
pci_disable_sriov()
sriov_disable()
sriov_disable() if !num_VFs :
if !num_VFs : return;
return; sriov_del_vfs()
sriov_del_vfs() ...
... klist_put()
klist_put() ...
... num_VFs = 0;
num_VFs = 0; device_unlock();
In this patch, when driver is removing, we get the device_lock()
to protect num_VFs, just like sriov_numvfs_store().
Fixes: 0dd8a25f355b ("net: hns3: disable sriov before unload hclge layer")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241101091507.3644584-1-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 6ed05c68cbca ("usb: musb: sunxi: Explicitly release USB PHY on
exit") will cause that usb phy @glue->xceiv is accessed after released.
1) register platform driver @sunxi_musb_driver
// get the usb phy @glue->xceiv
sunxi_musb_probe() -> devm_usb_get_phy().
2) register and unregister platform driver @musb_driver
musb_probe() -> sunxi_musb_init()
use the phy here
//the phy is released here
musb_remove() -> sunxi_musb_exit() -> devm_usb_put_phy()
3) register @musb_driver again
musb_probe() -> sunxi_musb_init()
use the phy here but the phy has been released at 2).
...
Fixed by reverting the commit, namely, removing devm_usb_put_phy()
from sunxi_musb_exit().
Fixes: 6ed05c68cbca ("usb: musb: sunxi: Explicitly release USB PHY on exit")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241029-sunxi_fix-v1-1-9431ed2ab826@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
HP 320 FHD Webcam (03f0:654a) seems to have flaky firmware like other
webcam devices that don't like the frequency inquiries. Also, Mic
Capture Volume has an invalid resolution, hence fix it to be 16 (as a
blind shot).
Link: https://bugzilla.suse.com/show_bug.cgi?id=1232768
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20241105120220.5740-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Backmerging to get the latest fixes from v6.12-rc6.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
This reverts commit d80a3091308491455b6501b1c4b68698c4a7cd24, reversing
changes made to 637f41476384c76d3cd7dcf5947caf2c8b8d7a9b:
2cf246143519 ("net: hns3: fix kernel crash when 1588 is sent on HIP08 devices")
3e22b7de34cb ("net: hns3: fixed hclge_fetch_pf_reg accesses bar space out of bounds issue")
d1c2e2961ab4 ("net: hns3: initialize reset_timer before hclgevf_misc_irq_init()")
5f62009ff108 ("net: hns3: don't auto enable misc vector")
2758f18a83ef ("net: hns3: Resolved the issue that the debugfs query result is inconsistent.")
662ecfc46690 ("net: hns3: fix missing features due to dev->features configuration too early")
3e0f7cc887b7 ("net: hns3: fixed reset failure issues caused by the incorrect reset type")
f2c14899caba ("net: hns3: add sync command to sync io-pgtable")
e6ab19443b36 ("net: hns3: default enable tx bounce buffer when smmu enabled")
The series is making the driver poke into IOMMU internals instead of
implementing appropriate IOMMU workarounds.
Link: https://lore.kernel.org/069c9838-b781-4012-934a-d2626fa78212@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RTC update work involves runtime resuming the UFS controller. Hence,
only start the RTC update work after runtime power management in the UFS
driver has been fully initialized. This patch fixes the following kernel
crash:
Internal error: Oops: 0000000096000006 [#1] PREEMPT SMP
Workqueue: events ufshcd_rtc_work
Call trace:
_raw_spin_lock_irqsave+0x34/0x8c (P)
pm_runtime_get_if_active+0x24/0x9c (L)
pm_runtime_get_if_active+0x24/0x9c
ufshcd_rtc_work+0x138/0x1b4
process_one_work+0x148/0x288
worker_thread+0x2cc/0x3d4
kthread+0x110/0x114
ret_from_fork+0x10/0x20
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Closes: https://lore.kernel.org/linux-scsi/0c0bc528-fdc2-4106-bc99-f23ae377f6f5@linaro.org/
Fixes: 6bf999e0eb41 ("scsi: ufs: core: Add UFS RTC support")
Cc: Bean Huo <beanhuo@micron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241031212632.2799127-1-bvanassche@acm.org
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2024-11-04
Alexander Hölzl contributes a patch to fix an error in the CAN j1939
documentation.
Thomas Mühlbacher's patch allows building of the {cc770,sja1000}_isa
drivers on x86_64 again.
A patch by me targets the m_can driver and limits the call to
free_irq() to devices with IRQs.
Dario Binacchi's patch fixes the RX and TX error counters in the c_can
driver.
The next 2 patches target the rockchip_canfd driver. Geert
Uytterhoeven's patch lets the driver depend on ARCH_ROCKCHIP. Jean
Delvare's patch drops the obsolete dependency on COMPILE_TEST.
The last 2 patches are by me and fix 2 regressions in the mcp251xfd
driver: fix broken coalescing configuration when switching CAN modes
and fix the length calculation of the Transmit Event FIFO (TEF) on
full TEF.
* tag 'linux-can-fixes-for-6.12-20241104' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: mcp251xfd_get_tef_len(): fix length calculation
can: mcp251xfd: mcp251xfd_ring_alloc(): fix coalescing configuration when switching CAN modes
can: rockchip_canfd: Drop obsolete dependency on COMPILE_TEST
can: rockchip_canfd: CAN_ROCKCHIP_CANFD should depend on ARCH_ROCKCHIP
can: c_can: fix {rx,tx}_errors statistics
can: m_can: m_can_close(): don't call free_irq() for IRQ-less devices
can: {cc770,sja1000}_isa: allow building on x86_64
can: j1939: fix error in J1939 documentation.
====================
Link: https://patch.msgid.link/20241104200120.393312-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"Where the last set of fixes was mostly drivers, this time the
devicetree changes all come at once, targeting mostly the Rockchips,
Qualcomm and NXP platforms.
The Qualcomm bugfixes target the Snapdragon X Elite laptops,
specifically problems with PCIe and NVMe support to improve
reliability, and a boot regresion on msm8939.
Also for Snapdragon platforms, there are a number of correctness
changes in the several platform specific device drivers, but none of
these are as impactful.
On the NXP i.MX platform, the fixes are all for 64-bit i.MX8 variants,
correcting individual entries in the devicetree that were incorrect
and causing the media, video, mmc and spi drivers to misbehave in
minor ways.
The Arm SCMI firmware driver gets fixes for a use-after-free bug and
for correctly parsing firmware information.
On the RISC-V side, there are three minor devicetree fixes for
starfive and sophgo, again addressing only minor mistakes. One device
driver patch fixes a problem with spurious interrupt handling"
* tag 'arm-fixes-6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (63 commits)
firmware: arm_scmi: Use vendor string in max-rx-timeout-ms
dt-bindings: firmware: arm,scmi: Add missing vendor string
riscv: dts: Replace deprecated snps,nr-gpios property for snps,dw-apb-gpio-port devices
arm64: dts: rockchip: Correct GPIO polarity on brcm BT nodes
arm64: dts: rockchip: Drop invalid clock-names from es8388 codec nodes
ARM: dts: rockchip: Fix the realtek audio codec on rk3036-kylin
ARM: dts: rockchip: Fix the spi controller on rk3036
ARM: dts: rockchip: drop grf reference from rk3036 hdmi
ARM: dts: rockchip: fix rk3036 acodec node
arm64: dts: rockchip: remove orphaned pinctrl-names from pinephone pro
soc: qcom: pmic_glink: Handle GLINK intent allocation rejections
rpmsg: glink: Handle rejected intent request better
arm64: dts: qcom: x1e80100: fix PCIe5 interconnect
arm64: dts: qcom: x1e80100: fix PCIe4 interconnect
arm64: dts: qcom: x1e80100: Fix up BAR spaces
MAINTAINERS: invert Misc RISC-V SoC Support's pattern
soc: qcom: socinfo: fix revision check in qcom_socinfo_probe()
arm64: dts: qcom: x1e80100-qcp: fix nvme regulator boot glitch
arm64: dts: qcom: x1e80100-microsoft-romulus: fix nvme regulator boot glitch
arm64: dts: qcom: x1e80100-yoga-slim7x: fix nvme regulator boot glitch
...
|
|
If Client send simultaneous SMB operations to ksmbd, It exhausts too much
memory through the "ksmbd_work_cache”. It will cause OOM issue.
ksmbd has a credit mechanism but it can't handle this problem. This patch
add the check if it exceeds max credits to prevent this problem by assuming
that one smb request consumes at least one credit.
Cc: stable@vger.kernel.org # v5.15+
Reported-by: Norbert Szetei <norbert@doyensec.com>
Tested-by: Norbert Szetei <norbert@doyensec.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
ksmbd_user_session_put should be called under smb3_preauth_hash_rsp().
It will avoid freeing session before calling smb3_preauth_hash_rsp().
Cc: stable@vger.kernel.org # v5.15+
Reported-by: Norbert Szetei <norbert@doyensec.com>
Tested-by: Norbert Szetei <norbert@doyensec.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
There is a race condition between ksmbd_smb2_session_create and
ksmbd_expire_session. This patch add missing sessions_table_lock
while adding/deleting session from global session table.
Cc: stable@vger.kernel.org # v5.15+
Reported-by: Norbert Szetei <norbert@doyensec.com>
Tested-by: Norbert Szetei <norbert@doyensec.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Commit 929ebc93ccaa ("cpufreq: intel_pstate: Set asymmetric CPU
capacity on hybrid systems") overlooked a corner case in which some
CPUs may be offline to start with and brought back online later,
after the intel_pstate driver has been registered, so their asymmetric
capacity will not be set.
Address this by calling hybrid_update_capacity() in the CPU
initialization path that is executed instead of the online path
for those CPUs.
Note that this asymmetric capacity update will be skipped during
driver initialization and mode switches because hybrid_max_perf_cpu
is NULL in those cases.
Fixes: 929ebc93ccaa ("cpufreq: intel_pstate: Set asymmetric CPU capacity on hybrid systems")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/1913414.tdWV9SEqCh@rjwysocki.net
|
|
Modify intel_pstate_register_driver() to clear hybrid_max_perf_cpu
before calling cpufreq_register_driver(), so that asymmetric CPU
capacity scaling is not updated until hybrid_init_cpu_capacity_scaling()
runs down the road. This is done in preparation for a subsequent
change adding asymmetric CPU capacity computation to the CPU init path
to handle CPUs that are initially offline.
The information on whether or not hybrid_max_perf_cpu was NULL before
it has been cleared is passed to hybrid_init_cpu_capacity_scaling(),
so full initialization of CPU capacity scaling can be skipped if it
has been carried out already.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/4616631.LvFx2qVVIh@rjwysocki.net
|
|
The code currently uses list_for_each_entry_rcu() while holding an SRCU
lock, triggering false positive warnings with CONFIG_PROVE_RCU=y
enabled:
drivers/nvme/host/core.c:3770 RCU-list traversed in non-reader section!!
While the list is properly protected by SRCU lock, the code uses the wrong
list traversal primitive. Replace list_for_each_entry_rcu() with
list_for_each_entry_srcu() to correctly indicate SRCU-based protection
and eliminate the false warning.
Fixes: be647e2c76b2 ("nvme: use srcu for iterating namespace list")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
This is a partial revert to commit 76a0a3f9cc2f ("e1000e: fix force smbus
during suspend flow"). That commit fixed a sporadic PHY access issue but
introduced a regression in runtime suspend flows.
The original issue on Meteor Lake systems was rare in terms of the
reproduction rate and the number of the systems affected.
After the integration of commit 0a6ad4d9e169 ("e1000e: avoid failing the
system during pm_suspend"), PHY access loss can no longer cause a
system-level suspend failure. As it only occurs when the LAN cable is
disconnected, and is recovered during system resume flow. Therefore, its
functional impact is low, and the priority is given to stabilizing
runtime suspend.
Fixes: 76a0a3f9cc2f ("e1000e: fix force smbus during suspend flow")
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix a race condition in the i40e driver that leads to MAC/VLAN filters
becoming corrupted and leaking. Address the issue that occurs under
heavy load when multiple threads are concurrently modifying MAC/VLAN
filters by setting mac and port VLAN.
1. Thread T0 allocates a filter in i40e_add_filter() within
i40e_ndo_set_vf_port_vlan().
2. Thread T1 concurrently frees the filter in __i40e_del_filter() within
i40e_ndo_set_vf_mac().
3. Subsequently, i40e_service_task() calls i40e_sync_vsi_filters(), which
refers to the already freed filter memory, causing corruption.
Reproduction steps:
1. Spawn multiple VFs.
2. Apply a concurrent heavy load by running parallel operations to change
MAC addresses on the VFs and change port VLANs on the host.
3. Observe errors in dmesg:
"Error I40E_AQ_RC_ENOSPC adding RX filters on VF XX,
please set promiscuous on manually for VF XX".
Exact code for stable reproduction Intel can't open-source now.
The fix involves implementing a new intermediate filter state,
I40E_FILTER_NEW_SYNC, for the time when a filter is on a tmp_add_list.
These filters cannot be deleted from the hash list directly but
must be removed using the full process.
Fixes: 278e7d0b9d68 ("i40e: store MAC/VLAN filters in a hash with the MAC Address as key")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In an event where the platform running the device control plane
is rebooted, reset is detected on the driver. It releases
all the resources and waits for the reset to complete. Once the
reset is done, it tries to build the resources back. At this
time if the device control plane is not yet started, then
the driver timeouts on the virtchnl message and retries to
establish the mailbox again.
In the retry flow, mailbox is deinitialized but the mailbox
workqueue is still alive and polling for the mailbox message.
This results in accessing the released control queue leading to
null-ptr-deref. Fix it by unrolling the work queue cancellation
and mailbox deinitialization in the reverse order which they got
initialized.
Fixes: 4930fbf419a7 ("idpf: add core init and interrupt request")
Fixes: 34c21fa894a1 ("idpf: implement virtchnl transaction manager")
Cc: stable@vger.kernel.org # 6.9+
Reviewed-by: Tarun K Singh <tarun.k.singh@intel.com>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When the device control plane is removed or the platform
running device control plane is rebooted, a reset is detected
on the driver. On driver reset, it releases the resources and
waits for the reset to complete. If the reset fails, it takes
the error path and releases the vport lock. At this time if the
monitoring tools tries to access link settings, it call traces
for accessing released vport pointer.
To avoid it, move link_speed_mbps to netdev_priv structure
which removes the dependency on vport pointer and the vport lock
in idpf_get_link_ksettings. Also use netif_carrier_ok()
to check the link status and adjust the offsetof to use link_up
instead of link_speed_mbps.
Fixes: 02cbfba1add5 ("idpf: add ethtool callbacks")
Cc: stable@vger.kernel.org # 6.7+
Reviewed-by: Tarun K Singh <tarun.k.singh@intel.com>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix Flow Director not allowing to re-map traffic to 0th queue when action
is configured to drop (and vice versa).
The current implementation of ethtool callback in the ice driver forbids
change Flow Director action from 0 to -1 and from -1 to 0 with an error,
e.g:
# ethtool -U eth2 flow-type tcp4 src-ip 1.1.1.1 loc 1 action 0
# ethtool -U eth2 flow-type tcp4 src-ip 1.1.1.1 loc 1 action -1
rmgr: Cannot insert RX class rule: Invalid argument
We set the value of `u16 q_index = 0` at the beginning of the function
ice_set_fdir_input_set(). In case of "drop traffic" action (which is
equal to -1 in ethtool) we store the 0 value. Later, when want to change
traffic rule to redirect to queue with index 0 it returns an error
caused by duplicate found.
Fix this behaviour by change of the type of field `q_index` from u16 to s16
in `struct ice_fdir_fltr`. This allows to store -1 in the field in case
of "drop traffic" action. What is more, change the variable type in the
function ice_set_fdir_input_set() and assign at the beginning the new
`#define ICE_FDIR_NO_QUEUE_IDX` which is -1. Later, if the action is set
to another value (point specific queue index) the variable value is
overwritten in the function.
Fixes: cac2a27cd9ab ("ice: Support IPv4 Flow Director filters")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Unloading the ice driver while switchdev port representors are added to
a bridge can lead to kernel panic. Reproducer:
modprobe ice
devlink dev eswitch set $PF1_PCI mode switchdev
ip link add $BR type bridge
ip link set $BR up
echo 2 > /sys/class/net/$PF1/device/sriov_numvfs
sleep 2
ip link set $PF1 master $BR
ip link set $VF1_PR master $BR
ip link set $VF2_PR master $BR
ip link set $PF1 up
ip link set $VF1_PR up
ip link set $VF2_PR up
ip link set $VF1 up
rmmod irdma ice
When unloading the driver, ice_eswitch_detach() is eventually called as
part of VF freeing. First, it removes a port representor from xarray,
then unregister_netdev() is called (via repr->ops.rem()), finally
representor is deallocated. The problem comes from the bridge doing its
own deinit at the same time. unregister_netdev() triggers a notifier
chain, resulting in ice_eswitch_br_port_deinit() being called. It should
set repr->br_port = NULL, but this does not happen since repr has
already been removed from xarray and is not found. Regardless, it
finishes up deallocating br_port. At this point, repr is still not freed
and an fdb event can happen, in which ice_eswitch_br_fdb_event_work()
takes repr->br_port and tries to use it, which causes a panic (use after
free).
Note that this only happens with 2 or more port representors added to
the bridge, since with only one representor port, the bridge deinit is
slightly different (ice_eswitch_br_port_deinit() is called via
ice_eswitch_br_ports_flush(), not ice_eswitch_br_port_unlink()).
Trace:
Oops: general protection fault, probably for non-canonical address 0xf129010fd1a93284: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: maybe wild-memory-access in range [0x8948287e8d499420-0x8948287e8d499427]
(...)
Workqueue: ice_bridge_wq ice_eswitch_br_fdb_event_work [ice]
RIP: 0010:__rht_bucket_nested+0xb4/0x180
(...)
Call Trace:
(...)
ice_eswitch_br_fdb_find+0x3fa/0x550 [ice]
? __pfx_ice_eswitch_br_fdb_find+0x10/0x10 [ice]
ice_eswitch_br_fdb_event_work+0x2de/0x1e60 [ice]
? __schedule+0xf60/0x5210
? mutex_lock+0x91/0xe0
? __pfx_ice_eswitch_br_fdb_event_work+0x10/0x10 [ice]
? ice_eswitch_br_update_work+0x1f4/0x310 [ice]
(...)
A workaround is available: brctl setageing $BR 0, which stops the bridge
from adding fdb entries altogether.
Change the order of operations in ice_eswitch_detach(): move the call to
unregister_netdev() before removing repr from xarray. This way
repr->br_port will be correctly set to NULL in
ice_eswitch_br_port_deinit(), preventing a panic.
Fixes: fff292b47ac1 ("ice: add VF representors one by one")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When sealing or unsealing a key blob we currently do not wait for
the AEAD cipher operation to finish and simply return after submitting
the request. If there is some load on the system we can exit before
the cipher operation is done and the buffer we read from/write to
is already removed from the stack. This will e.g. result in NULL
pointer dereference errors in the DCP driver during blob creation.
Fix this by waiting for the AEAD cipher operation to finish before
resuming the seal and unseal calls.
Cc: stable@vger.kernel.org # v6.10+
Fixes: 0e28bf61a5f9 ("KEYS: trusted: dcp: fix leak of blob encryption key")
Reported-by: Parthiban N <parthiban@linumiz.com>
Closes: https://lore.kernel.org/keyrings/254d3bb1-6dbc-48b4-9c08-77df04baee2f@linumiz.com/
Signed-off-by: David Gstir <david@sigma-star.at>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
KASAN reports an out of bounds read:
BUG: KASAN: slab-out-of-bounds in __kuid_val include/linux/uidgid.h:36
BUG: KASAN: slab-out-of-bounds in uid_eq include/linux/uidgid.h:63 [inline]
BUG: KASAN: slab-out-of-bounds in key_task_permission+0x394/0x410
security/keys/permission.c:54
Read of size 4 at addr ffff88813c3ab618 by task stress-ng/4362
CPU: 2 PID: 4362 Comm: stress-ng Not tainted 5.10.0-14930-gafbffd6c3ede #15
Call Trace:
__dump_stack lib/dump_stack.c:82 [inline]
dump_stack+0x107/0x167 lib/dump_stack.c:123
print_address_description.constprop.0+0x19/0x170 mm/kasan/report.c:400
__kasan_report.cold+0x6c/0x84 mm/kasan/report.c:560
kasan_report+0x3a/0x50 mm/kasan/report.c:585
__kuid_val include/linux/uidgid.h:36 [inline]
uid_eq include/linux/uidgid.h:63 [inline]
key_task_permission+0x394/0x410 security/keys/permission.c:54
search_nested_keyrings+0x90e/0xe90 security/keys/keyring.c:793
This issue was also reported by syzbot.
It can be reproduced by following these steps(more details [1]):
1. Obtain more than 32 inputs that have similar hashes, which ends with the
pattern '0xxxxxxxe6'.
2. Reboot and add the keys obtained in step 1.
The reproducer demonstrates how this issue happened:
1. In the search_nested_keyrings function, when it iterates through the
slots in a node(below tag ascend_to_node), if the slot pointer is meta
and node->back_pointer != NULL(it means a root), it will proceed to
descend_to_node. However, there is an exception. If node is the root,
and one of the slots points to a shortcut, it will be treated as a
keyring.
2. Whether the ptr is keyring decided by keyring_ptr_is_keyring function.
However, KEYRING_PTR_SUBTYPE is 0x2UL, the same as
ASSOC_ARRAY_PTR_SUBTYPE_MASK.
3. When 32 keys with the similar hashes are added to the tree, the ROOT
has keys with hashes that are not similar (e.g. slot 0) and it splits
NODE A without using a shortcut. When NODE A is filled with keys that
all hashes are xxe6, the keys are similar, NODE A will split with a
shortcut. Finally, it forms the tree as shown below, where slot 6 points
to a shortcut.
NODE A
+------>+---+
ROOT | | 0 | xxe6
+---+ | +---+
xxxx | 0 | shortcut : : xxe6
+---+ | +---+
xxe6 : : | | | xxe6
+---+ | +---+
| 6 |---+ : : xxe6
+---+ +---+
xxe6 : : | f | xxe6
+---+ +---+
xxe6 | f |
+---+
4. As mentioned above, If a slot(slot 6) of the root points to a shortcut,
it may be mistakenly transferred to a key*, leading to a read
out-of-bounds read.
To fix this issue, one should jump to descend_to_node if the ptr is a
shortcut, regardless of whether the node is root or not.
[1] https://lore.kernel.org/linux-kernel/1cfa878e-8c7b-4570-8606-21daf5e13ce7@huaweicloud.com/
[jarkko: tweaked the commit message a bit to have an appropriate closes
tag.]
Fixes: b2a4df200d57 ("KEYS: Expand the capacity of a keyring")
Reported-by: syzbot+5b415c07907a2990d1a3@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/000000000000cbb7860611f61147@google.com/T/
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
